Search NASA⌕ Search

SEARCH · Search NASA

Results for “Tunnel Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Wind tunnel tests on a tail-less swept wing span-distributed cargo aircraft configuration

The configuration consisted of a 30 deg -swept, untapered, untwisted wing utilizing a low-moment cambered airfoil of 20 percent streamwise thickness designed for low wave drag at M = 0.6, C sub L = 0.4. The tests covered a range of Mach numbers 0.3 to 0.725 and chord Reynolds number 1,100,000 to 2,040,000, angles of attack up to model buffet and sideslip angles + or - 4 deg. Configuration build up, wing pod filleting, airfoil modification and trailing edge control deflection effects were briefly investigated. Three wing tip vertical tail designs were also tested. Wing body filleting and a simple airfoil modification both produced increments to maximum lift/drag ratio. Addition of pods eliminated pitch instability of the basic wing. While the magnitude of these benefits probably was Reynolds number sensitive, they underline the potential for improving the aerodynamics of the present configuration. The cruise parameter (product of Mach number and lift/drag ratio) attained a maximum close to the airfoil design point. The configuration was found to be positively stable with normal control effectiveness about all three axes in the Mach number and C sub L range of interest.

Rao, D. M.↗

Low speed wind tunnel test of ground proximity and deck edge effects on a lift cruise fan V/STOL configuration, volume 1

The characteristics were determined of a lift cruise fan V/STOL multi-mission configuration in the near proximity to the edge of a small flat surface representation of a ship deck. Tests were conducted at both static and forward speed test conditions. The model (0.12 scale) tested was a four fan configuration with modifications to represent a three fan configuration. Analysis of data showed that the deck edge effects were in general less critical in terms of differences from free air than a full deck (in ground effect) configuration. The one exception to this was when the aft edge of the deck was located under the center of gravity. This condition, representative of an approach from the rear, showed a significant lift loss. Induced moments were generally small compared to the single axis control power requirements, but will likely add to the pilot work load.

Stewart, V. R.↗

A comparison of predictions obtained from wind tunnel tests and the results from cruising flight: Airbus and Concorde

Following a summary of the methods used to establish aerodynamic data and propulsion data, a comparison was made in the form of the drag (or thrust) difference between flight results and predictions made on the basis of these data. Certain hypothesis and improvements on aerodynamic data were presented in order to explain the slight deficit found on Airbus and Concorde.

Berger, J.↗

Initial wind tunnel tests at Mach 4 and 7 of a hydrogen-burning, airframe-integrated scramjet

A research investigation of a new, fixed-geometry, hydrogen-burning scramjet engine concept, designed for total airframe integration, is currently in progress. Two heavily instrumented engine models incorporate inlet and combustor designs developed previously in component tests. Initial tests of these subscale engine models are being conducted in ground facilities at conditions simulating flight at Mach numbers 4 and 7. The scramjet test results which are presented include inlet performance, ignition/reaction aids, inlet-combustor interactions, and engine performance in terms of thrust balance measurements and internal pressure and heating rate distributions. The relationship of these results to flight engine performance is discussed.

Guy, R. W.↗

Low-speed wind-tunnel tests of a 1/10-scale model of an advanced arrow-wing supersonic cruise configuration designed for cruise at Mach 2.2

The low-speed longitudinal and lateral-directional characteristics of a scale model of an advanced arrow-wing supersonic cruise configuration were investigated in tests conducted at a Reynolds number of 4.19 x 10 to the 6th power based on the mean aerodynamic chord, with an angle of attack range from - 6 deg to 23 deg and sideslip angle range from -15 deg to 20 deg. The effects of segmented leading-edge flaps, slotted trailing-edge flaps, horizontal and vertical tails, and ailerons and spoilers were determined. Extensive pressure data and flow visualization pictures with non-intrusive fluorescent mini-tufts were obtained.

Yip, L. P.↗

Wind-tunnel/flight correlation study of aerodynamic characteristics of a large flexible supersonic cruise airplane CXB-70-1). 1: Wind-tunnel tests of a 0.03-scale model at Mach numbers from 0.6 to 2.53

The longitudinal and lateral forces and moments for a 0.03 scale deformed rigid, static force model of the XB-70-1 airplane were determined. Control effectiveness was determined for the elevon in pitch and roll, for the canard, and for the rudders. Component effects of the canard, deflected with tips, variable position canopy, bypass doors, and bleed dump fairing were measured. The effects of small variations in inlet mass flow ratio and small amounts of asymmetric deflection of the wing tips were assessed.

Daugherty, J. C.↗

Two-dimensional wind-tunnel tests of a NASA supercritical airfoil with various high-lift systems. Volume 1: Data analysis

High-lift systems for a NASA, 9.3%, method for calculating the viscous flow about two-dimensional multicomponent airfoils was evaluated by comparing its predictions with test data. High-lift systems derived from supercritical airfoils were compared in terms of performance to high-lift systems derived from conventional airfoils. The high-lift systems for the supercritical airfoil were designed to achieve maximum lift and consisted of: a single-slotted flap; a double-slotted flap and a leading-edge slat; and a triple-slotted flap and a leading-edge slat. Agreement between theoretical predictions and experimental results are also discussed.

Omar, E.↗

Force and moment data from a wind-tunnel test of a tilt-nacelle V/STOL propulsion system with an attitude control vane

A large scale, tilt nacelle V/STOL propulsion system, with an attitude control vane assembly mounted in the exhaust, was tested. The effectiveness of the control vane as well as the aerodynamic characteristics of the entire propulsion system were determined. The results, in the form of tabulated coefficients, for both the vane forces and moments and the total forces and moments produced by the propulsion system are presented.

Betzina, M. D.↗

Wind-tunnel test of an articulated helicopter rotor model with several tip shapes

Six interchangeable tip shapes were tested: a square (baseline) tip, an ogee tip, a subwing tip, a swept tip, a winglet tip, and a short ogee tip. In hover at the lower rotational speeds the swept, ogee, and short ogee tips had about the same torque coefficient, and the subwing and winglet tips had a larger torque coefficient than the baseline square tip blades. The ogee and swept tip blades required less torque coefficient at lower rotational speeds and roughly equivalent torque coefficient at higher rotational speeds compared with the baseline square tip blades in forward flight. The short ogee tip required higher torque coefficient at higher lift coefficients than the baseline square tip blade in the forward flight test condition.

Berry, J. D.↗

Icing tunnel tests of a glycol-exuding porous leading edge ice protection system on a general aviation airfoil

A glycol-exuding porous leading edge ice protection system was tested. Results show that the system is very effective in preventing ice accretion (anti-ice mode) or removing ice from an airfoil. Minimum glycol flow rates required for anti-icing are a function of velocity, liquid water content in the air, ambient temperature, and droplet size. Large ice caps were removed in only a few minutes using anti-ice flow rates. It was found that the shed time is a function of the type of ice, size of the ice cap, angle of attack, and glycol flow rate. Wake survey measurements show that there is no significant drag penalty for the installation or operation of the system tested.

Kohlman, D. L.↗

Phase 2 and 3 wind tunnel tests of the J-97 powered, external augmentor V/STOL model

Modifications were made to the model to improve longitudinal acceleration capability during transition from hovering to wing borne flight. A rearward deflection of the fuselage augmentor thrust vector is shown to be beneficial in this regard. Other agmentor modifications were tested, notably the removal of both endplates, which improved acceleration performance at the higher transition speeds. The model tests again demonstrated minimal interference of the fuselage augmentor on aerodynamic lift. A flapped canard surface also shows negligible influence on the performance of the wing and of the fuselage augmentor.

Garland, D. B.↗

Evaluation of four subcritical response methods for on-line prediction flutter onset in wind-tunnel tests

The methods were evaluated for use in tests where the flutter model is excited solely by airstream turbulence. The methods were: randomdec, power-spectral-density, peak-hold, and cross-spectrum. The test procedure was to maintain a constant Mach number (M) and increase the dynamic pressure (g) in incremental steps. The test Mach numbers were 0.65, 0.75, 0.82, 0.90, and 1.15. The four methods provided damping trends by which the flutter mode could be tracked and extrapolated to a flutter-onset q. A hard flutter point was obtained at M = 0.82. The peak-hold and cross-spectrum methods gave reliable results and could be most readily used for on-line testing. At M = 0.82, a p-k analysis predicted the same flutter mode as the experiment but a 6-percent lower flutter q. At the subcritical dynamic pressures, calculated damping values were appreciably lower than measured data.

Ruhlin, C. L.↗

Elastic suspension of a wind tunnel test section

Experimental verification of the theory describing arbitrary motions of an airfoil is reported. The experimental apparatus is described. A mechanism was designed to provide two separate degrees of freedom without friction or backlash to mask the small but important aerodynamic effects of interest.

Hacker, R.↗

Rolling flow wind tunnel tests of F-18 aircraft

The lateral directional characteristics of an F-18 aircraft was investigated. Aerodynamic derivatives associated with pure roll rate, or the 'p' derivatives were obtained. The model is described and the procedures used to obtain and correct the data, and a graphical presentation of the results are presented. These results include graphs of the lateral directional static stability derivatives versus angle of attack, and the lateral directional force and moment coefficients versus nondimensional roll rate. Results are presented for several configurations including complete, complete without vertical tails, complete without horizontal tails, fuselage wing and fuselage alone. Each of these configuations was tested with and without wing leading edge extensions. The basic control surfaces were deflected and the results were investigated.

Lutze, F. H.↗

Static calibration for measurement of loads in wind tunnel tests on Shuttle surface tiles

A description is given of the procedures used for the static calibrations of the Coe (1981) sensor array to determine normal force, pitching moment, and rolling moment from the ensemble of sensor outputs. The use of independent data to confirm the validity of the calibration is also described. Two methods are used in calibrating the Coe sensors. In the first, calibration loads and readings are arranged in matrix form and are assumed to be related in a linear fashion. In the second, each Coe sensor reading is regarded as a sum of contributions from each of the calibration loads. It is shown that the Coe load sensors, in conjunction with either of two data analysis methods, can be used to determine the forces and moments experienced by a Shuttle TPS tile.

Rummler, D. R.↗

Loads and performance data from a wind-tunnel test of model articulated helicopter rotors with 2 different blade torsional stiffnesses

A passive means of tailoring helicopter rotor blades to improve performance and reduce loads was evaluated. The parameters investigated were blade torsional stiffness, blade section camber, and distance between blade structural elastic axis and blade tip aerodynamic center. This offset was accomplished by sweeping the tip. The investigation was conducted at advance ratios of 0.20, 0.30, and 0.40. Data are presented without analysis; however, cross referencing of performance data and harmonic loads data may be useful to the analyst for validating aeroelastic theories and design methodologies as well as for evaluating passive aeroelastic tailoring or rotor blade parameters.

Yeager, W. T., Jr.↗