Search NASA⌕ Search

SEARCH · Search NASA

Results for “Yield Strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

The combined effects of hydrogen and aging condition on the deformation and fracture behavior of a precipitation-hardened nickel-base superalloy

The effect of hydrogen (H) on the deformation behavior of Monel K-500 in various isothermal heat treatment conditions (non-aged, under-aged, peak-aged, and over-aged) was assessed via uniaxial mechanical testing. H-charged and non-charged specimens were strained to failure to facilitate a comparison of ductility, fracture surface morphology, strength, and work hardening behavior. For all examined heat treatment conditions, H charging leads to a significant reduction in ductility, which is accompanied by a consistent change in fracture surface morphology from ductile microvoid coalescence to brittle intergranular fracture. While H charging led to a systematic enhancement in the yield strength of all heat treatments, the three age-hardened conditions exhibited a more than 2-fold increase relative to the non-aged heat treatment. This suggests that H modifies the dislocation–precipitate interactions, which also manifest themselves through changes in work hardening metrics related to the dislocation storage and recovery rates. In particular, the H-charged peak-aged specimen exhibited a significant increase in initial hardening (dislocation storage) rate relative to the H-charged under-aged specimen. Transmission electron microscopy of these samples revealed the onset of widespread dislocation looping in the H-charged peak-aged sample, in addition to the planar slip bands characteristic of the non-charged condition. This result suggests that hydrogen induces the particle shearing-to-looping transition at smaller particle sizes. Possible mechanistic explanations for this observed behavior are presented.

36 MATERIALS SCIENCE↗

Cyclic behavior of turbine disk alloys at 650 C

Five gas turbine disk alloys representing a range of strengths and processing methods were tested for resistance to both cyclic crack initiation and propagation at 650 C using a 0.33 Hz fatigue cycle and a cycle incorporating a 900 s tensile dwell. At the low strain ranges pertinent to disks, resistance to crack initiation increased with increasing tensile yield strength among the alloys, though the advantage was somewhat smaller for the creep fatigue cycle. Cyclic crack growth resistance, however, decreased with increasing strength and very markedly so for the dwell cycle.

Cowles, B. A.↗

Effects of niobium and tantalum on the microstructure and strength of ferritic-martensitic steels

Herein, detailed investigations of two ferritic-martensitic steels, i.e., Nb- and Ta-steel, indicate that the higher Nb diffusivity and the lower nucleation driving force of Nb-carbide promote preferential nucleation of Nb-carbides at grain boundaries and thus a higher boundary occupancy than Ta-carbides, which favored greater creep resistance of Nb-steel than that of Ta-steel despite their similar yield strength.

36 MATERIALS SCIENCE↗

Mechanical properties of niobium radio-frequency cavities

Radio-frequency cavities made of bulk niobium are one of the components used in modern particle accelerators. The mechanical stability is an important aspect of cavity design, which typically relies on finite-element analysis simulations using material properties from tensile tests on sample. This contribution presents the results of strain and resonant frequency measurements as a function of a uniform pressure up to 722 kPa, applied to single-cell niobium cavities with different crystallographic structure, purity and treatments. In addition, burst tests of high-purity multi-cell cavities with different crystallographic structure have been conducted up to the tensile strength of the material. Finite-element analysis of the single-cell cavity geometry is in good agreement with the observed behavior in the elastic regime assuming a Young's modulus value of 88.5 GPa and a Poisson's ratio of 0.4, regardless of crystallographic structure, purity or treatment. However, the measured yield strength and tensile strength depend on crystallographic structure, material purity and treatment. In particular, the results from this study show that the mechanical properties of niobium cavities with large crystals are comparable to those of cavities made of fine-grain niobium.

36 MATERIALS SCIENCE↗

The Effects of Annealing after Equal Channel Angular Extrusion (ECAE) on Mechanical and Magnetic Properties of 49Fe-49Co-2V Alloy

Equal channel angular extrusion (ECAE) of 49Fe-49Co-2V, also known as Hiperco® 50A or Permendur-2V, greatly improves the strength and ductility of this alloy, while sacrificing soft magnetic performance. In this work, ECAE Hiperco specimens were subjected to post-ECAE annealing in order to improve soft magnetic properties. The microstructure, mechanical properties, and magnetic performance are summarized in this study. Annealing begins above 650°C and a steep decline in yield strength is observed for heat treatments between 700 and 840°C due to grain growth and the Hall-Petch effect, although some strength benefit is still observed in fully annealed ECAE material compared to conventionally processed bar. Soft magnetic properties were assessed through B-H hysteresis curves from which coercivity (Hc) values were extracted. Hc decreases rapidly with annealing above 650°C as well, i.e. improved soft magnetic behavior. The observed trend is attributed to annealing and grain growth in this temperature regime, which facilitates magnetic domain wall movement. The coercivity vs. grain size results generally follow the trend predicted in the literature. The magnetic behavior of annealed ECAE material compares favorably to conventional bar, possibly due to mild crystallographic texturing which enhances properties in the post-ECAE annealed material. Overall, this study highlights a definitive tradeoff between mechanical and magnetic properties brought about by post-ECAE annealing and grain growth.

annealing↗

The effect of microstructure and strength on the fracture toughness of an 18 ni, 300 grade maraging steel

Methods for increasing the strength of maraging steels are discussed. An investigation was conducted to systematically vary the strength of 18 weight percent nickel, 300 grade maraging steel, to isolate any attending microstructural changes, and to study the effects of these changes on the fracture toughness of the alloy. A study aimed at determining the aging behavior of the program alloy was carried out to provide data by which to estimate yield strength. The effects of various alloying materials on the strength of the maraging steel are examined. The mechanical properties of the 300 grade maraging steel were determined by tension tests, fatigue precracked Charpy impact tests, and plane strain fracture toughness tests.

Psioda, J. A.↗

Effects cascade debris and helium bubbles on the strength of aged plutonium

The radioactive decay of aging Pu is dominated by α-decay. This persistent α-decay produces crystalline defects in the form of dislocation loops and helium bubbles that evolve with time. Comparable defects are produced in other metallic alloys when subject to neutron irradiation, and these defects are known to modify the plastic deformation of irradiated materials. Models have been developed for these irradiated materials and validated against experimental confirmations of yield strength and the concomitant microstructural evolution. In this paper, we deploy those previously developed models and apply their mechanics to plutonium aging.

Chemical elements↗

Microstructural, Oxidation, and Mechanical Behavior of NbTi-Based Refractory Alloys with 5 to 10 Pct Co, Cr, and Ni Additions

NbTi-based refractory alloys with additions of Co, Cr, and Ni represent an interesting medium-entropy alloy system with potential for protective oxide film formation, high strength, and ductility. This study investigates the microstructural evolution, oxidation behavior, and mechanical properties of NbTi-based alloys containing 5 to 10 at. pct Co, Cr, and Ni. CALPHAD predictions suggest that this composition range can be heat treated to obtain a predominantly body-centered cubic matrix phase. Mechanical properties, including microhardness, yield strength, maximum strength, and specific strength are evaluated through isothermal compression tests conducted between room temperature and 800 °C. The oxidation kinetics of these alloys are assessed through discontinuous oxidation tests. Parabolic oxidation kinetics were observed for NbTi–10Ni and NbTi–5Co, while linear oxidation kinetics were found for NbTi–10Cr and NbTi–10(CoCrNi). Microstructures and oxide layers are characterized using X-ray diffraction, electron backscatter diffraction, energy-dispersive X-ray spectroscopy, and scanning electron microscopy. All alloys exhibit significant mechanical softening between room temperature and 800 °C, with elastic-perfectly plastic flow observed at 800 °C. The addition of 10 pct Cr to NbTi resulted in two BCC phases up to 1050 °C, conflicting with CALPHAD predictions of a single-phase solid solution at this temperature, and resulting in higher flow stress at 800 °C. NbTi–10(CoCrNi) exhibited the lowest flow stress at 800 °C despite having more ‘cocktail effect’ potential and insufficient molar fractions of Co, Cr, or Ni to form a desirable protective oxide film.

36 MATERIALS SCIENCE↗

Highly luminescent two dimensional excitons in atomically thin CdSe nanosheets

Atomically thin Cadmium Selenide (CdSe) nanosheets have been synthesized using a surfactant mediated growth technique. The transmission electron microscopy studies confirm the presence of single layered nanosheets with thickness 1.31 nm and their stacking structures which are complemented by the small angle x-ray scattering measurements. The strongly bound and polarized character of two dimensional excitonic states with enhanced oscillator strength yielding distinct narrow blue luminescence has been observed from the CdSe nanosheets using room temperature based optical studies.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

The effect of TiB2 reinforcement on the mechanical properties of an Al-Cu-Li alloy-based metal-matrix composite

The addition of ceramic particles to aluminum based alloys can substantially improve mechanical properties, especially Young's modulus and room and elevated temperature strengths. However, these improvements typically occur at the expense of tensile ductility. The mechanical properties are evaluated to a metal matrix composite (MMC) consisting of an ultrahigh strength aluminum lithium alloy, Weldalite (tm) 049, reinforced with TiB2 particles produced by an in situ precipitation technique called the XD (tm) process. The results are compared to the behavior of a nonreinforced Weldalite 049 variant. It is shown that both 049 and 049-TiB2 show very attractive warm temperature properties e.g., 625 MPa yield strength at 150 C after 100 h at temperature. Weldalite 049 reinforced with a nominal 4 v pct. TiB2 shows an approx. 8 pct. increase in modulus and a good combination of strength (529 MPa UTS) and ductility (6.5 pct.) in the T3 temper. And the high ductility of Weldalite 049 in the naturally aged and underaged tempers makes the alloy a good, high strength matrix for ceramic reinforcement.

Source record↗

Corrosion and Fatigue Behavior of High-Strength Steel Treated with a Zn-Alloy Thermo-diffusion Coating

High and low cycle fatigue tests were conducted on high-strength steel using four-point bending. The materials tested were ASTM A723 steel in the as-machined condition, grit-blasted condition, MIL-DTL-16232 heavy manganese phosphate-coated condition, and ASTM A1059 Zn-alloy thermo-diffusion coated (Zn-TDC). The ASTM A723 steel base material exhibits a yield strength of ~1000 MPa. The effects of the surface treatments versus uncoated steel were examined. The fatigue life of the Zn-TDC specimens was generally reduced on as-coated specimens versus uncoated or phosphate-coated specimens. Several mechanisms are examined including the role of compressive residual stress relief with the Zn-TDC process as well as fatigue crack initiation from the hardened Zn-Fe alloy surface layer produced in the gas-metal reaction. Additionally, the effects of corrosion pitting on the fatigue life of coated specimens are explored as the Zn-TDC specimens exhibit significantly improved corrosion resistance over phosphate-coated and oiled specimens.

36 MATERIALS SCIENCE↗

Intermediate strength alloys for high temperature service in liquid-salt cooled energy systems

An alloy consists essentially of, in terms of weight percent: 6 to 8.5 Cr, 5.5 to 13.5 Mo, 0.4 to 7.5 W, 1 to 2 Ti, 0.7 to 0.85 Mn, 0.05 to 0.3 Al, up to to 0.1 Co, 0.08 to 0.5 C, 1 to 5 Ta, 1 to 4 Nab, 1 to 3 Hf, balance Ni. The alloy is characterized by, at 850.degree. C., a yield strength of at least 36 Ksi, a tensile strength of at least 40 Ksi, a creep rupture life at 12 Ksi of at least 72.1 hours, and a corrosion rate, expressed in weight loss [g/(cm2sec)].times.10.sup.-11 during a 1000 hour immersion in liquid FLiNaK at 850.degree. C., in the range of 8 to 25.

36 MATERIALS SCIENCE↗

Synergistic Effects of Molten Salt Corrosion and Proton Irradiation on Grain Boundary Strength in Ni-20Cr

Nickel-based alloys are leading contenders for use as structural materials in molten salt reactors. While there have been extensive studies on the impact of fluoride/chloride-based molten salt corrosion on the microstructural evolution of various nickel-based alloys, the effects of simultaneous molten salt corrosion and radiation on the mechanical integrity of grain boundaries (GBs) remain underexplored. In this study, we use a Ni-20Cr model alloy to investigate this issue, subjecting it to simultaneous molten fluoride salt corrosion and proton irradiation. We performed cross-sectional and chemically-sensitive electron microscopy characterization of the microstructures of these materials, identifying the characteristic corrosion-induced microstructure and local chemical heterogeneity near GBs. After developing a sample preparation method for reliable characterization of GB strength, we assess the mechanical degradation of GBs using in situ push-to-pull micro tensile tests. Our findings reveal that voids induced by corrosion are the primary influence on the failure mode of GBs, regardless of whether proton irradiation is present. For materials that exhibit ductile fracture, those subjected to simultaneous corrosion and radiation exhibit lower yield strengths than those exposed to corrosion alone, which may be linked to the previously observed phenomenon of proton irradiation-decelerated intergranular corrosion in molten salt.

36 - MATERIALS SCIENCE↗

Weld bead reinforcement removal: A method of improving the strength and ductility of peaked welds in 2219-T87 aluminum alloy plate

The results of a study to determine the degree to which the ductility and tensile properties of peaked welds could be enhanced by removing the reinforcing bead and fairing the weld nugget into the adjacent parent metal are presented. The study employed 2219-T87 aluminum alloy plate, tungsten inert gas (TIG) welding, and 2319 filler wire. The study concluded that significant improvements in peak weld, ultimate strength, and ductility can be obtained through removal and fairing of the weld reinforcing bead. The specimens so treated and tested in this program exhibited ultimate strength improvements of 2 to 3 percent for peak angles of 5.8 to 10 degrees and 10 to 22 percent for welds with peak angles of 11.7 to 16.9 degrees. It was also determined that removal of the weld bead enhanced the ability of peaked welds to straighten when exposed to cyclic loading at stress levels above the yield strength.

Lovoy, C. V.↗

Yielding and deformation behavior of the single crystal nickel-base superalloy PWA 1480

Interrupted tensile tests were conducted to fixed plastic strain levels in 100 ordered single crystals of the nickel based superalloy PWA 1480. Testing was done in the range of 20 to 1093 C, at strain rate of 0.5 and 50%/min. The yield strength was constant from 20 to 760 C, above which the strength dropped rapidly and became a stong function of strain rate. The high temperature data were represented very well by an Arrhenius type equation, which resulted in three distinct temperature regimes. The deformation substructures were grouped in the same three regimes, indicating that there was a fundamental relationship between the deformation mechanisms and activation energies. Models of the yielding process were considered, and it was found that no currently available model was fully applicable to this alloy. It was also demonstrated that the initial deformation mechanism (during yielding) was frequently different from that which would be inferred by examining specimens which were tested to failure.

Milligan, W. W., Jr.↗

Yielding and deformation behavior of the single crystal superalloy PWA 1480

Interrupted tensile tests were conducted to fixed plastic strain levels in 100 ordered single crystals of the nickel based superalloy PWA 1480. Testing was done in the range of 20 to 1093 C, at strain rate of 0.5 and 50 percent/min. The yield strength was constant from 20 to 760 C, above which the strength dropped rapidly and became a strong function of strain rate. The high temperature data were represented very well by an Arrhenius type equation, which resulted in three distinct temperature regimes. The deformation substructures were grouped in the same three regimes, indicating that there was a fundamental relationship between the deformation mechanisms and activation energies. Models of the yielding process were considered, and it was found that no currently available model was fully applicable to this alloy. It was also demonstrated that the initial deformation mechanism (during yielding) was frequently different from that which would be inferred by examining specimens which were tested to failure.

Milligan, Walter W.↗

Mechanical Tensile Testing of Hiperco 50A at Cryogenic Temperature

Hiperco 50A is a highly desired material for use in cryogenic applications, specifically for adiabatic demagnetization refrigerators (ADRs) due to its magnetic field shielding capabilities. Although the alloy has good strength, there is a concern with the material's brittle behavior which is believed to worsen at low temperature based on previous tests. The testing described here investigates the mechanical properties of Hiperco 50A at cryogenic temperature through mechanical tensile testing to failure and evaluation of the failed coupons. The methods and techniques used to determine the elongation, yield strength, ultimate tensile strength, and break strength of the material as well as the results will be presented here.

material properties↗

Helium irradiation induced ultra-high strength nanotwinned Cu with nanovoids

There are mounting studies that show nanotwinned (NT) metals have enhanced radiation tolerance. Yet, the mechanical deformability of irradiated nanotwinned metals is a largely under explored subject. Here we look at the mechanical properties of He ion irradiated nanotwinned Cu with preexisting nanovoids. In comparison with coarse-grained Cu, nanovoid nanotwinned (NV-NT) Cu exhibits prominently improved radiation tolerance. Moroever, in situ micropillar compression tests show that the irradiated NV-NT Cu has an ultrahigh yield strength of ~1.6 GPa with significant plasticity. Post radiation analyses show that twin boundaries are decorated with He bubbles and thick stacking faults. These stacking fault modified twin boundaries introduce significant strengthening in NT Cu. This study provides further insight into the design of high-strength, advanced radiation tolerant nanostructured materials for nuclear reactor applications.

36 MATERIALS SCIENCE↗