Search NASA⌕ Search

SEARCH · Search NASA

Results for “aerodynamic optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Application of an optimized winglet configuration to an advanced commercial transport

The design is presented of an aircraft which employs an integrated wing and winglet lift system. Comparison was made with a conventional baseline configuration employing a high-aspect-ratio supercritical wing. An optimized wing-winglet combination was selected from four proposed configurations for which aerodynamic, structural, and weight characteristics were evaluated. Each candidate wing-winglet configuration was constrained to the same induced drag coefficient as the baseline aircraft. The selected wing-winglet configuration was resized for a specific medium-range mission requirement, and operating costs were estimated for a typical mission. Study results indicated that the wing-winglet aircraft was lighter and could complete the specified mission at less cost than the conventional wing aircraft. These indications were sensitive to the impact of flutter characteristics and, to a lesser extent, to the performance of the high-lift system. Further study in these areas is recommended to reduce uncertainty in future development.

Shollenberger, C. A.↗

Optimum structural design with static aeroelastic constraints

The static aeroelastic performance characteristics, divergence velocity, control effectiveness and lift effectiveness are considered in obtaining an optimum weight structure. A typical swept wing structure is used with upper and lower skins, spar and rib thicknesses, and spar cap and vertical post cross-sectional areas as the design parameters. Incompressible aerodynamic strip theory is used to derive the constraint formulations, and aerodynamic load matrices. A Sequential Unconstrained Minimization Technique (SUMT) algorithm is used to optimize the wing structure to meet the desired performance constraints.

Bowman, Keith B↗

Project HyBuJET

A conceptual Hypersonic Business Jet (HyBuJet) was examined. The main areas of concentration include: aerodynamics, propulsion, stability and control, mission profile, and atmospheric heating. In order to optimize for cruise conditions, a waverider configuration was chosen for the high lift drag ratio and low wave drag. The leading edge and lower surface of a waverider was mapped out from a known flow field and optimized for cruising at Mach 6 and at high altitudes. The shockwave generated by a waverider remains attached along the entire leading edge, allowing for a larger compression along the lower surface. Three turbofan ramjets were chosen as the propulsion of the aircraft due to the combination of good subsonic performance along with high speed propulsive capabilities. A combination of liquid silicon convective cooling for the leading edges with a highly radiative outer skin material was chosen to reduce the atmospheric heating to acceptable level.

Ramsay, Tom↗

Aerodynamic and structural studies of joined-wing aircraft

A method for rapidly evaluating the structural and aerodynamic characteristics of joined-wing aircraft was developed and used to study the fundamental advantages attributed to this concept. The technique involves a rapid turnaround aerodynamic analysis method for computing minimum trimmed drag combined with a simple structural optimization. A variety of joined-wing designs are compared on the basis of trimmed drag, structural weight, and, finally, trimmed drag with fixed structural weight. The range of joined-wing design parameters resulting in best cruise performance is identified. Structural weight savings and net drag reductions are predicted for certain joined-wing configurations compared with conventional cantilever-wing configurations.

Kroo, Ilan↗

Development of the quasi-procedural method for use in aircraft configuration optimization

The performance of the quasi-procedural analysis system in optimization tasks is investigated. In particular, the quasi-procedural method is applied to the complete mission optimization of a medium-sized transport aircraft using a vortex-lattice aerodynamic model and finite element structural analysis of the wing and the tail. Some modifications and improvements to the system, required in order to complete this task, are described. The performance of the system is compared with that of the standard procedural system, and it is shown that the quasi-procedural approach reduces the analysis required to reach the optimum. The overall cost is shown to be strongly dependent on the analysis architecture and data structure.

Gage, P.↗

Finite state aeroelastic model for use in rotor design optimization

In this article, a rotor aeroelastic model based on a newly developed finite state dynamic wake, coupled with blade finite element analysis, is described. The analysis is intended for application in rotor blade design optimization. A coupled simultaneous system of differential equations combining blade structural dynamics and aerodynamics is established in a formulation well-suited for design sensitivity computation. Each blade is assumed to be an elastic beam undergoing flap bending, lead-lag bending, elastic twist, and axial deflections. Aerodynamic loads are computed from unsteady blade element theory where the rotor three-dimensional unsteady wake is described by a generalized dynamic wake model. Correlation of results obtained from the analysis with flight test data is provided to assess model accuracy.

He, Chengjian↗

Propulsion/airframe interference for ducted propfan engines with ground effect

The advanced propfan propulsion systems design of the next-generation subsonic transport aircraft has been of interest to many airline companies in the past several years. This is due to the studies which indicate that an efficient ducted propfan engine technology offers a significant reduction in aircraft fuel consumption. However, because of the geometric complexity of the configuration, one challenge is the integration of the ducted propfan engine with the airframe so that aerodynamic interference effects frequently encountered near the nacelle can be minimized, or perhaps, optimized. To understand this interaction phenomenon better, it is desirable to have a reliable and efficient computational tool that can predict propeller effects on the flowfield around complex configurations.

Arabshahi, Abdollah↗

Optimization of Turbine Blade Design for Reusable Launch Vehicles

To facilitate design optimization of turbine blade shape for reusable launching vehicles, appropriate techniques need to be developed to process and estimate the characteristics of the design variables and the response of the output with respect to the variations of the design variables. The purpose of this report is to offer insight into developing appropriate techniques for supporting such design and optimization needs. Neural network and polynomial-based techniques are applied to process aerodynamic data obtained from computational simulations for flows around a two-dimensional airfoil and a generic three- dimensional wing/blade. For the two-dimensional airfoil, a two-layered radial-basis network is designed and trained. The performances of two different design functions for radial-basis networks, one based on the accuracy requirement, whereas the other one based on the limit on the network size. While the number of neurons needed to satisfactorily reproduce the information depends on the size of the data, the neural network technique is shown to be more accurate for large data set (up to 765 simulations have been used) than the polynomial-based response surface method. For the three-dimensional wing/blade case, smaller aerodynamic data sets (between 9 to 25 simulations) are considered, and both the neural network and the polynomial-based response surface techniques improve their performance as the data size increases. It is found while the relative performance of two different network types, a radial-basis network and a back-propagation network, depends on the number of input data, the number of iterations required for radial-basis network is less than that for the back-propagation network.

Shyy, Wei↗

Guidance and Control Algorithms for the Mars Entry, Descent and Landing Systems Analysis

The purpose of the Mars Entry, Descent and Landing Systems Analysis (EDL-SA) study was to identify feasible technologies that will enable human exploration of Mars, specifically to deliver large payloads to the Martian surface. This paper focuses on the methods used to guide and control two of the contending technologies, a mid- lift-to-drag (L/D) rigid aeroshell and a hypersonic inflatable aerodynamic decelerator (HIAD), through the entry portion of the trajectory. The Program to Optimize Simulated Trajectories II (POST2) is used to simulate and analyze the trajectories of the contending technologies and guidance and control algorithms. Three guidance algorithms are discussed in this paper: EDL theoretical guidance, Numerical Predictor-Corrector (NPC) guidance and Analytical Predictor-Corrector (APC) guidance. EDL-SA also considered two forms of control: bank angle control, similar to that used by Apollo and the Space Shuttle, and a center-of-gravity (CG) offset control. This paper presents the performance comparison of these guidance algorithms and summarizes the results as they impact the technology recommendations for future study.

Davis, Jody L.↗

Parametric Design of Injectors for LDI-3 Combustors

Application of a partially calibrated National Combustion Code (NCC) for providing guidance in the design of the 3rd generation of the Lean-Direct Injection (LDI) multi-element combustion configuration (LDI-3) is summarized. NCC was used to perform non-reacting and two-phase reacting flow computations on several LDI-3 injector configurations in a single-element and a five-element injector array. All computations were performed with a consistent approach for mesh-generation, turbulence, spray simulations, ignition and chemical kinetics-modeling. Both qualitative and quantitative assessment of the computed flowfield characteristics of the several design options led to selection of an optimal injector LDI- 3 design that met all the requirements including effective area, aerodynamics and fuel-air mixing criteria. Computed LDI-3 emissions (namely, NOx, CO and UHC) will be compared with the prior generation LDI- 2 combustor experimental data at relevant engine cycle conditions.

injectors↗

Update on the Development of a Flutter Analysis Capability for Unconventional Aircraft Concepts Using HCDstruct

Following years of development, the Higher-fidelity Conceptual Design and structural optimization (HCDstruct) tool is being extended to support dynamic aeroservoelastic analysis and structural optimization for advanced aircraft concepts. These required enhancements include: the development of an aerodynamic matching routine for correcting Nastran’s doublet-lattice method aerodynamics; the implementation of control surface structural models; and the implementation of support for Nastran’s flutter solution sequence (SOL 145). This paper presents an update on the implementation of generalized control surface structural models and support for Nastran SOL 145.

Quinlan, Jesse R.↗

Mars Sample Return Earth Entry System Helicopter Drop Test Reconstruction

The Mars Sample Return campaign conducted four successful helicopter drop tests of the Earth Entry System at the Utah Test and Training Range on October, 2023. The tests acquired data for the 52.5 deg sphere cone geometry that can be used to develop models for the terminal descent aerodynamics and flight dynamics used to model ground impact conditions. The acquired test data included both sensor data outputs from an on-board inertial measurement unit, global positioning system, and video cameras as well as atmospheric measurements from weather balloons. This data was processed using a Kalman filter/smoother to reconstruct the capsule’s trajectory and aerodynamics. An equation-error method was used to reconcile the aerodynamics by solving for a set of dispersions in the aerodynamic database that form a best-fit to the reconstructed aerodynamics. The reconstructed trajectories were compared with flight simulations generated using Program to Optimize Simulated Trajectories II. The results indicate that the simulation underpredicted the vehicle oscillation amplitudes. The reconstruction exhibits a persistent low-amplitude oscillation that does not damp out as predicted.

Chris D Karlgaard↗

Mars Sample Return Earth Entry System Helicopter Drop Test Reconstruction

The Mars Sample Return campaign conducted four successful helicopter drop tests of the Earth Entry System at the Utah Test and Training Range on October, 2023. The tests acquired data for the 52.5 deg sphere cone geometry that can be used to develop models for the terminal descent aerodynamics and flight dynamics used to model ground impact conditions. The acquired test data included both sensor data outputs from an on-board inertial measurement unit, global positioning system, and video cameras as well as atmospheric measurements from weather balloons. This data was processed using a Kalman filter/smoother to reconstruct the capsule’s trajectory and aerodynamics. An equation-error method was used to reconcile the aerodynamics by solving for a set of dispersions in the aerodynamic database that form a best-fit to the reconstructed aerodynamics. The reconstructed trajectories were compared with flight simulations generated using Program to Optimize Simulated Trajectories II. The results indicate that the simulation underpredicted the vehicle oscillation amplitudes. The reconstruction exhibits a persistent low-amplitude oscillation that does not damp out as predicted.

Chris D Karlgaard↗

Wing optimization for space shuttle orbiter vehicles

The results were presented of a parametric study performed to determine the optimum wing geometry for a proposed space shuttle orbiter. The results of the study establish the minimum weight wing for a series of wing-fuselage combinations subject to constraints on aerodynamic heating, wing trailing edge sweep, and wing over-hang. The study consists of a generalized design evaluation which has the flexibility of arbitrarily varying those wing parameters which influence the vehicle system design and its performance. The study is structured to allow inputs of aerodynamic, weight, aerothermal, structural and material data in a general form so that the influence of these parameters on the design optimization process can be isolated and identified. This procedure displays the sensitivity of the system design of variations in wing geometry. The parameters of interest are varied in a prescribed fashion on a selected fuselage and the effect on the total vehicle weight is determined. The primary variables investigated are: wing loading, aspect ratio, leading edge sweep, thickness ratio, and taper ratio.

Surber, T. E.↗

Effect of Transition Aerodynamics on Aeroassist Flight Experiment Trajectories

Various transition methods are used here to study the viscous effects encountered in low density, hypersonic flight, through the transition from free molecular to continuum flow. Methods utilizing Viking data, Shuttle Orbiter data, a Potter number parameter, and a Shock Reynolds number were implemented in the Program to Optimize Simulated Trajectories (POST). Simulations of the Aeroassist Flight Experiment (AFE) using open loop guidance were used to assess the aerodynamic performance of the vehicle. A bank angle was found for each transition method that would result in a 200 nautical-mile apogee. Once this was done, the open loop guidance was replaced by the proposed guidance algorithm for the AFE. Simulations were again conducted using that guidance and the different transitions for comparison. For the gains used, the guidance system showed some sensitivity in apogee altitude to the transition method assumed, but the guidance was able to successfully complete the mission.

Minier, Elizabeth A.↗

Aerostructural Level Set Topology Optimization for a Common Research Model Wing

The purpose of this work is to use level set topology optimization to improve the design of a representative wing box structure for the NASA common research model. The objective is to minimize the total compliance of the structure under aerodynamic and body force loading, where the aerodynamic loading is coupled to the structural deformation. A taxi bump case was also considered, where only body force loads were applied. The trim condition that aerodynamic lift must balance the total weight of the aircraft is enforced by allowing the root angle of attack to change. The level set optimization method is implemented on an unstructured three-dimensional grid, so that the method can optimize a wing box with arbitrary geometry. Fast matching and upwind schemes are developed for an unstructured grid, which make the level set method robust and efficient. The adjoint method is used to obtain the coupled shape sensitivities required to perform aerostructural optimization of the wing box structure.

Dunning, Peter D.↗

Computationally Efficient Control Co-Design Optimization Framework with Mixed-Fidelity Fluid and Structure Analysis: OpenTurbineCoDe (OTCD) - ARPA-E ATLANTIS Phase I Project (Final Technical Report)

The goal of the Department of Energy (DOE) Advanced Research Projects Agency-Energy (ARPA-E) Aerodynamic Turbines Lighter and Afloat with Nautical Technologies and Integrated Servo-control (ATLANTIS) Program is to develop new technologies for floating offshore wind turbines, or wind farms, using the discipline of control co-design (CCD.) In this context, our goal is to develop a computationally efficient optimization framework for design of floating offshore wind turbines. Our specific aim is to utilize high-fidelity structural, aerodynamic, aero-structural tools, and to derive control-oriented reduced- or low-order models directly from the high-fidelity tools. We proposed a mixed-fidelity modeling approach which means that we are also using low- and mid-fidelity tools when necessary. This research is conducted by a multidisciplinary team consisting of Rutgers University, University of Michigan, Brigham Young University, and the National Renewable Energy Laboratory (NREL). The computational framework, called OpenTurbineCoDe, is designed to integrate, where possible, traditional structural, aerodynamic, aeroelastic models (e.g., OpenFAST) and advanced control algorithms with higher fidelity simulation tools including Reynolds-averaged Navier–Stokes (RANS) solvers, and three-dimensional structural finite element solvers. All the high-fidelity tools used in this research provide numerically exact gradients to facilitate both efficient optimization and local linearization for control implementation.

17 WIND ENERGY↗

Aerodynamic Parameter Estimation for the X-43A (Hyper-X) from Flight Data

Aerodynamic parameters were estimated based on flight data from the third flight of the X-43A hypersonic research vehicle, also called Hyper-X. Maneuvers were flown using multiple orthogonal phase-optimized sweep inputs applied as simultaneous control surface perturbations at Mach 8, 7, 6, 5, 4, and 3 during the vehicle descent. Aerodynamic parameters, consisting of non-dimensional longitudinal and lateral stability and control derivatives, were estimated from flight data at each Mach number. Multi-step inputs at nearly the same flight conditions were also flown to assess the prediction capability of the identified models. Prediction errors were found to be comparable in magnitude to the modeling errors, which indicates accurate modeling. Aerodynamic parameter estimates were plotted as a function of Mach number, and compared with estimates from the pre-flight aerodynamic database, which was based on wind-tunnel tests and computational fluid dynamics. Agreement between flight estimates and values computed from the aerodynamic database was excellent overall.

Morelli, Eugene A.↗