Search NASA⌕ Search

SEARCH · Search NASA

Results for “atomic migration”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Radiation damage buildup by athermal defect reactions in nickel and concentrated nickel alloys

We develop a new method using binary collision approximation simulating the Rutherford backscattering spectrometry in channeling conditions (RBS/C) from molecular dynamics atom coordinates of irradiated cells. The approach allows comparing experimental and simulated RBS/C signals as a function of depth without fitting parameters. The simulated RBS/C spectra of irradiated Ni and concentrated solid solution alloys (CSAs, NiFe and NiCoCr) show a good agreement with the experimental results. The good agreement indicates the damage evolution under damage overlap conditions in Ni and CSAs at room temperature is dominated by defect recombination and migration induced by irradiation rather than activated thermally.

36 MATERIALS SCIENCE↗

Thermal conductance enhanced via inelastic phonon transport by atomic vacancies at Cu/Si interfaces

Understanding and controlling heat transfer across interfaces has become an important issue for the performance of micro- and nanoscale electronics, as well as achieving a high figure of merit for thermoelectrics. Intrinsic and extrinsic defects can have a significant impact on thermal transport in bulk materials and across interfaces, but the mechanism is not well understood. Here, nonequilibrium molecular dynamics simulations are used to determine the impact of interfacial atomic vacancies on thermal transport across a Cu/Si junction. In contrast to the reduction in thermal transport typically seen with bulk defects, we find that by introducing atomic vacancies at a concentration of 6.3% near the interface in either or both materials, the interfacial thermal conductance can be increased by up to 76%. By controlling the initial positions of the vacancies and keeping track of their movements and population, we find that interfacial thermal transport is dependent on temperature, vacancy concentration, and distribution, and a positive correlation between the conductance and point defect activities (extent of vacancy migration, rate of Frenkel defect creation and annihilation) is observed. Further calculations based on the phonon density of states and normal mode decomposition reveal that the increase in interfacial thermal conductance originates primarily from high-frequency phonons, supported by enhanced inelastic phonon transport which contributes to more than 60% of the increase. Our findings suggest a practical way to manipulate inelastic phonon conversion through the presence of defects, which provides an alternative perspective on improving thermal transport between materials with a large lattice mismatch.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Specific features of defect and mass transport in concentrated fcc alloys

We report that diffusion and mass transport are basic properties that control materials performance, such as phase stability, solute decomposition and radiation tolerance. While understanding diffusion in dilute alloys is a mature field, concentrated alloys are much less studied. Here, atomic-scale diffusion and mass transport via vacancies and interstitial atoms are compared in fcc Ni, Fe and equiatomic Ni-Fe alloy. High temperature properties were determined using conventional molecular dynamics on the microsecond timescale, whereas the kinetic activation-relaxation (k-ART) approach was applied at low temperatures. The k-ART was also used to calculate transition states in the alloy and defect transport coefficients. The calculations reveal several specific features. For example, vacancy and interstitial defects migrate via different alloy components, diffusion is more sluggish in the alloy and, notably, mass transport in the concentrated alloy cannot be predicted on the basis of diffusion in its pure metal counterparts. Lastly, the percolation threshold for the defect diffusion in the alloy is discussed and it is suggested that this phenomenon depends on the properties and diffusion mechanisms of specific defects.

36 MATERIALS SCIENCE↗

Integrity Monitoring of Mercury Discharge Lamps

Mercury discharge lamps are critical in many trapped ion frequency standard applications. An integrity monitoring system can be implemented using end-of-life signatures observed in operational mercury discharge lamps, making it possible to forecast imminent failure and to take action to mitigate the consequences (such as switching to a redundant system). Mercury lamps are used as a source of 194-nm ultraviolet radiation for optical pumping and state selection of mercury trapped ion frequency standards. Lamps are typically fabricated using 202Hg distilled into high-purity quartz, or other 194-nm transmitting material (e.g., sapphire). A buffer gas is also placed into the bulb, typically a noble gas such as argon, neon, or krypton. The bulbs are driven by strong RF fields oscillating at .200 MHz. The lamp output may age over time by two internal mechanisms: (1) the darkening of the bulb that attenuates light transmission and (2) the loss of mercury due to migration or chemical interactions with the bulb surface. During fabrication, excess mercury is placed into a bulb, so that the loss rate is compensated with new mercury emanating from a cool tip or adjacent reservoir. The light output is nearly constant or varies slightly at a constant rate for many months/years until the mercury source is depleted. At this point, the vapor pressure abruptly falls and the total light output and atomic clock SNR (signal-to-noise ratio) decrease. After several days to weeks, the light levels decrease to a point where the atomic clock SNR is no longer sufficient to stay in lock, or the lamp self-extinguishes. This signature has been observed in four separate end-of-life lamp failures while operating in the Deep Space Network (DSN). A simple integrator circuit can observe and document steady-state lamp behavior. When the light levels drop over a predetermined time interval by a specified amount (e.g., 20 percent), an alarm is set. For critical operational applications, such as the DSN or in space flight, this warning provides notice that a failure may be imminent, and for operators or control algorithm to take action.

Tjoelker, Robert L.↗

Transitions in the morphology and critical stresses of gliding dislocations in multiprincipal element alloys

Refractory multiprincipal element alloys (MPEAs) are promising material candidates for high-temperature, high-strength applications. However, their deformation mechanisms, particularly at the dislocation scale, are unusual compared to those of conventional alloys, making it challenging to understand the origin of their high strength. Here, using an atomistically informed phase-field dislocation dynamics model, we study transitions in the morphology and critical stresses of long gliding screw dislocations over extended distances in a refractory MPEA. The model MPEA crystal accounts for the atomic-scale fluctuations in chemical composition across the glide planes via spatially correlated lattice energies and for the differences in glide resistances between screw and edge dislocations of unit length. Here, we show that the dislocation moves in a stop-start motion, alternating between wavy morphology in free flight and nearly recovered straight screw orientation in full arrest. The periods of wavy glide are due to variable kink-pair formation and migration rates along the length, where portions with higher rates glide more quickly. The critical stress to initiate motion corresponds to the stress required to form and migrate a kink pair at the weakest region along the length of the dislocation. Heterogeneity in lattice energy leads to variability in the local stress-strain response and to a strain hardening-like response, in which the critical stress to reactivate glide increases with glide distance. Statistical assessment of hundreds of realizations of dislocations indicates that the amount of hardening directly scales with the dispersion in underlying lattice energy.

3-dimensional systems↗

Atomic structure, energetics, dynamics, and manipulation of topological solitons in indium chains on Si(111) surfaces

Based on scanning tunneling microscopy and first-principles theoretical studies, we characterize the precise atomic structure of a topological soliton in In chains grown on Si(111) surfaces. Variabletemperature measurements of the soliton population allow us to determine the soliton formation energy to be 60 meV, smaller than one half of the band gap of 200 meV. Once created, these solitons have very low mobility, even though the activation energy is only about 20 meV; the sluggish nature is attributed to the exceptionally low attempt frequency for soliton migration. We further demonstrate local electric field enhanced soliton dynamics, and the feasibility of aggregating solitons into soliton polymers.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Degradation of Intercalated Graphite Epoxy Composites Exposed to Low Earth Orbit

Four different graphite fiber/epoxy composites were exposed to the wake-side low Earth orbit (LEO) environment on the Optical Reflector Materials Experiment III (ORMatE-III) platform mounted on the exterior of the ISS for two years in order to determine their long term durability in the space environment. Three of the composite samples used bromine intercalated P100 fibers and one used pristine P100 fibers. One of the P100-Br samples was coated with a protective SiO2 layer, and half of another was coated with SiO2. Results were compared with the EOIM-III experiment which exposed the same materials in LEO in the ram direction for 42 h on the Space Shuttle. Although the atomic oxygen (AO) fluence of the ORMatE-III samples was one-third of the EOIM-III exposure, the resulting effects were qualitatively the same. Both found that SiO2 coated intercalated graphite composites showed no AO erosion, verifying that conventional protection strategies are applicable to bromine intercalated composites. Both found that bromine intercalation does not alter the AO erosion rates of graphite fiber/epoxy composites. Both found no bromine was detected to have migrated into the surrounding epoxy, even for highly eroded fibers and epoxy, allaying fears that bromination could compromise the properties of the epoxy. And both found no corrosive bromine was detected to have been released by the fibers allaying fears that outgassing could degrade sensitive electronics. The uncoated EOIM-III samples suffered slightly greater erosion resulting in a slightly higher solar absorptance. The general conclusion is that ram AO exposure had very similar effects on graphite fiber epoxy composites in both the EOIM-III and ORMatE-III experiments, and in neither case did bromine intercalation of the fibers substantially influence that degradation.

Intercalated graphite↗

Intergranular corrosion of Ni-30Cr in high-temperature hydrogenated water after removing surface passivating film

Abstract High-resolution transmission electron microscopy and atom probe tomography are used to characterize the initial passivation and subsequent intergranular corrosion of degraded grain boundaries in a model Ni-30Cr alloy exposed to 360 °C hydrogenated water. Upon initial exposure for 1000 h, the alloy surface directly above the grain boundary forms a thin passivating film of Cr 2 O 3 , protecting the underlying grain boundary from intergranular corrosion. However, the metal grain boundary experiences severe Cr depletion and grain boundary migration during this initial exposure. To understand how Cr depletion affects further corrosion, the local protective film was sputtered away using a glancing angle focused ion beam. Upon further exposure, the surface fails to repassivate, and intergranular corrosion is observed through the Cr-depleted region. Through this combination of high-resolution microscopy and localized passive film removal, we show that, although high-Cr alloys are resistant to intergranular attack and stress corrosion cracking, degradation-induced changes in the underlying metal at grain boundaries make the material more susceptible once the initial passive film is breached.

(S)TEM↗

In-situ Characterization of CuFe2O4 and Cu/Fe3O4 Water-Gas Shift Catalysts

Mixtures of copper and iron oxides are used as industrial catalysts for the water-gas shift (WGS, CO + H2O → H2 + CO2). In-situ time-resolved X-ray diffraction, X-ray absorption fine structure, and atomic pair distribution function analysis were used to study the reduction of CuFe2O4 with CO and the behavior of CuFe2O4 and Cu/Fe2O3 catalysts under WGS reaction conditions. Metal↔oxygen↔metal interactions enhance the stability of Cu2+ and Fe3+ in the CuFe2O4 lattice, and the mixed-metal oxide is much more difficult to reduce than CuO or Fe2O3. Furthermore, after heating mixtures of CuFe2O4/CuO in the presence of CO or CO/H2O, the cations of CuO migrate into octahedral sites of the CuFe2O4 lattice at temperatures (200-250 oC) in which CuO is not stable. Above 250 oC, copper leaves the oxide, the occupancy of the octahedral sites in CuFe2O4 decreases, and diffraction lines for metallic Cu appear. From 350 to 450 oC, there is a massive reduction of CuFe2O4 with the formation of metallic Cu and Fe3O4. At this point, the sample becomes catalytically active for the production of H2 from the reaction of H2O with CO. Neutral Cu0 (i.e. no Cu+1 or Cu+2 cations) is the active species in the catalysts, but interactions with the oxide support are necessary in order to obtain high catalytic activity. These studies illustrate the importance of in-situ characterization when dealing with mixed-metal oxide WGS catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An integrated approach for structural characterization of complex solid state electrolytes: the case of lithium lanthanum titanate

For neutron scattering and first principles simulation we integrate them to reveal the atomic-level to nanoscale structure of lithium lanthanum titanate (LLTO), a representative solid electrolyte material with applications in Li-ion batteries. Furthermore, the integrated approach solves the hierarchical local structure of LLTO in detail, including the coupled chemical order and topological distortion, as well as their correlation length scale and the spatial modulation with coherent boundaries. Ab initio molecular dynamics simulations are used to map out the distribution of the mobile ions and identify the migration pathway. This integrated approach provides a powerful means for detailed study of materials with complex local chemical and topological environment.

25 ENERGY STORAGE↗

Origin of Hund's multiplicity rule in singly excited helium: Existence of a conjugate Fermi hole in the lower spin state

The origin of Hund's multiplicity rule in the low-lying excited states of the helium atom has been studied by considering the two-dimensional helium atom. The internal part of the full configuration interaction wave functions for the (2s) and (2p) singlet-triplet pairs of states has been extracted and visualized in the three-dimensional internal space (r{sub 1},r{sub 2}, {phi}{sub -}). The internal wave function of the singlet states without electron repulsion has a significant probability around the origin of the internal space while the corresponding probability of the triplet wave function is negligible in this region due to the presence of a Fermi hole. The electron-electron repulsion potential has been visualized also in the internal space. It manifests itself by three striking poles penetrating exactly into the spatial region defined by the Fermi hole. Because of the existence of these strong potential poles in the vicinity of the Fermi hole a major part of the singlet probability migrates out of this region. In contrast, the corresponding triplet wave function is less affected by these poles due to the presence of the Fermi hole. The singlet probability is shown to migrate from its original region close to the origin to a region far away where either r{sub 1} or r{sub 2} are large. This results in a more diffuse electron density distribution and a smaller electron repulsion energy of the singlet state than of the corresponding triplet state. The mechanism of the evolution of the singlet probability toward the region of large r{sub i} (i =1, 2) in the presence of the electron repulsion potential has been rationalized on the basis of a new concept called conjugate Fermi hole.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Oxygen vacancy defects in Ta{sub 2}O{sub 5} showing long-range atomic re-arrangements

The structure, formation energy, and energy levels of the various oxygen vacancies in Ta{sub 2}O{sub 5} have been calculated using the λ phase model. The intra-layer vacancies give rise to unusual, long-range bonding rearrangements, which are different for each defect charge state. The 2-fold coordinated intra-layer vacancy is the lowest cost vacancy and forms a deep level 1.5 eV below the conduction band edge. The 3-fold intra-layer vacancy and the 2-fold inter-layer vacancy are higher cost defects, and form shallower levels. The unusual bonding rearrangements lead to low oxygen migration barriers, which are useful for resistive random access memory applications.

36 MATERIALS SCIENCE↗

Sliding of coherent twin boundaries

Coherent twin boundaries (CTBs) are internal interfaces that can play a key role in markedly enhancing the strength of metallic materials while preserving their ductility. They are known to accommodate plastic deformation primarily through their migration, while experimental evidence documenting large-scale sliding of CTBs to facilitate deformation has thus far not been reported. We show here that CTB sliding is possible whenever the loading orientation enables the Schmid factors of leading and trailing partial dislocations to be comparable to each other. This theoretical prediction is confirmed by real-time transmission electron microscope experimental observations during uniaxial deformation of copper pillars with different orientations and is further validated at the atomic scale by recourse to molecular dynamics simulations. Our findings provide mechanistic insights into the evolution of plasticity in heavily twinned face-centered cubic metals, with the potential for optimizing mechanical properties with nanoscale CTBs in material design.

36 MATERIALS SCIENCE↗

Evaluation of electrochemical performance and redox activity of Fe in Ti doped layered P2-Na0.67Mn0.5Fe0.5O2 cathode for sodium ion batteries

Here, we report a wet synthesis-based titanium doping strategy to improve the structural stability and electrochemical performances, such as cycling stability and rate capability, of P2-type Na 0.67 Fe 0.5 Mn 0.5 O 2 layered oxide cathodes. Through Ti 4+ doping aimed at replacing some of the Mn and Fe atoms in the crystal structure, effective mitigation of the Jahn Teller distortion caused by active Mn 3+ before charging and Fe 4+ after charging was achieved. X-ray diffraction (XRD), Raman spectroscopy, Electrochemical Impedance Spectroscopy (EIS) and Mössbauer spectroscopy were used to investigate the effects of the Ti 4+ dopant before and after cycling. It was observed that Ti 4+ doping increased the Na layer thickness, minimized the lattice volume strain, showed better structural stability, minimally decreased Fe migration to the Na layer, and lowered charge transfer resistance in these P2-type cathodes. Overall, our reported synthesis methodology and electrochemical characterizations highlight the feasibility of Ti doping in sodium layered oxide P2-type cathodes.

25 ENERGY STORAGE↗