Search NASA⌕ Search

SEARCH · Search NASA

Results for “computer-aided”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Small Satellite-sized Hypersonic Inflatable Aerodynamic Decelerators for Interplanetary Science Missions

To make the most of ridesharing opportunities, small satellite (SmallSat) mission designers endeavor to pack as much payload into a SmallSat-class form factor as possible. The mass and volume constraints of this smaller vehicle class present a challenge for interplanetary mission sets that require a means of achieving orbit insertion at their destination of interest. For a fully propulsive orbit insertion design, this may translate to the propellant mass being a significant fraction of the overall vehicle mass and prolonged insertion time. Aerocapture is a single quick maneuver that can significantly reduce the required propellant mass for orbit insertion. Because aerocapture uses a planet’s atmosphere to achieve the necessary change in velocity, a protective aeroshell is needed. The constraints imposed on secondary payloads render traditional rigid aeroshells mass and space prohibitive for the SmallSat class of vehicles; thus, warranting consideration of deployable designs that can be stowed compactly until needed for atmospheric entry. The Hypersonic Inflatable Aerodynamic Decelerator (HIAD) is a deployable aeroshell that leverages inflatable toroids to achieve the large drag area needed for aerodynamic deceleration. While the technology is currently being analyzed for Mars human-scale missions, it has the potential applicability for interplanetary SmallSat-scale missions as well. This paper highlights a study conducted during an internship at NASA Langley Research Center to investigate the feasibility of using a scaled-down HIAD design in SmallSat aerocapture missions. Several scaling methodologies are investigated including use of parametric models and direct computer-aided design (CAD) model scaling. Candidate HIAD configurations that conform to secondary payload adapter requirements are identified. The Program to Optimize Simulated Trajectories II (POST2) is utilized to conduct orbit insertion performance and trajectory sensitivity studies using the candidate configurations at Earth, Venus, and Mars. The results of the study indicate that multiple SmallSat-sized HIAD designs, targeting a range of SmallSat payload classes, are feasible for planetary aerocapture missions to Mars and Venus as well as Earth-based aerocapture missions.

Shelly C. Mann↗
NASA NTRSDate not supplied

Investigating the Applications of In-Situ Resource Utilization for Future Crewed Mars Missions

Several advancements are necessary before humans can safely explore Mars. One emerging strategy is In-Situ Resource Utilization (ISRU): the process of extracting raw materials found onsite and converting them into usable products to ensure a constant flow of vital resources and greatly reduce overall mission cost. Scientists must confirm the presence and accessibility of these resources for future crewed missions. Our team investigated the feasibility of ISRU in NE Syrtis, a region of Mars with varied geology, mineralogy, and hydrological history. NE Syrtis has abundant subsurface water and a diverse suite of mineral deposits including olivine, phyllosilicates, sulfates, and carbonates–all of which can be leveraged for fuel, medical supplies, and/or construction materials. We conceptualized a joint rover and helicopter expedition to analyze and sample these minerals over a two-year primary mission using Java Mission-planning and Analysis for Remote Sensing (JMARS), Planetary Data Systems (PDS), and Computer-Aided Design (CAD). We plotted a strategic traverse to regions of interest identified from remote sensing data and planned operations at each target. Our mission aimed to prepare for human presence on Mars by demonstrating the utility and viability of ISRU-focused operations.

Zahra M. Ronizi↗
NASA NTRSDate not supplied

A Design Framework for Thick and Thin Tow-Steered Composites Using Mechanics of Structure Genome

The design of tow-steered composites is one of the most popular and promising topics under the class of variable stiffness structures. In this work, the authors propose a new design framework and tool for the optimization of tow-steered composites. Mechanics of structure genome (MSG) provides accurate computation of plate/shell section properties including thick and highly curved structures. The computed section properties can be directly used in commercial computer-aided engineering tools. Tow-steered composites are modeled through a design framework wherein tow paths are parameterized in a general way and projected onto a finite element mesh, and MSG calculates the local shell/plate properties. The result is a complete workflow from design parameter input to structural performance evaluation. An open-source optimization software package is used to enable constrained optimization of structural stiffness for the broad tow-steered composite design space. Numerical examples are provided to demonstrate the capabilities of this tool and the promise and potential of tow-steered designs that optimize structural performance while satisfying manufacturing constraints.

Su Tian↗
NASA NTRSDate not supplied

A Design Framework for Thick and Thin Tow-Steered Composites Using Mechanics of Structure Genome

The design of tow-steered composites is one of the most popular and promising topics under the class of variable stiffness structures. In this work, the authors propose a new design framework and tool for the optimization of tow-steered composites. Mechanics of structure genome (MSG) provides accurate computation of plate/shell section properties including thick and highly curved structures. The computed section properties can be directly used in commercial computer-aided engineering tools. Tow-steered composites are modeled through a design framework wherein tow paths are parameterized in a general way and projected onto a finite element mesh, and MSG calculates the local shell/plate properties. The result is a complete workflow from design parameter input to structural performance evaluation. An open-source optimization software package is used to enable constrained optimization of structural stiffness for the broad tow-steered composite design space. Numerical examples are provided to demonstrate the capabilities of this tool and the promise and potential of tow-steered designs that optimize structural performance while satisfying manufacturing constraints.

Su Tian↗
NASA NTRS2023

Plug20 Test Report: Particle Image Velocimetry (PIV) Measurements

This report provides turbulent flow statistics made using particle image velocimetry (PIV) for several internally mixed exhaust systems with external plugs (Plug20 designs). The tests were conducted at the NASA Glenn Research Center’s Aero-Acoustic Propulsion Laboratory (AAPL) in May and June 2022. The corresponding acoustic data for the configurations and flows presented in this report can be found in an earlier Technical Memorandum, NASA/TM-20210010291, “Plug20 Test Report.” The Plug20 nozzle family was designed to represent commercial supersonic vehicles in the 2025 to 2035 timeframe with a bypass ratio around 4, having an internal mixer, with and without an external plug to improve nacelle boattail drag and shock. The flow conditions measured represent engine cycles for commercial supersonic aircraft at takeoff, having pressure ratios of 2.0 and heated fan and core streams, measured both with and without a flight stream surrounding the plume. A few unheated flow conditions were also tested to tie results to other baseline test results. The PIV measurements in both streamwise and cross-stream planes are described, along with brief analysis to visually catalog the contents and confirm their validity. In this analysis, the streamwise PIV is found to match benchmark datasets within its experimental error. However, the cross-stream turbulent quantities measured by two systems do not match each other or the streamwise measurements in amplitude—caution is required when using the cross-stream data. Data acquired and included in this report are (1) velocity statistics of the plumes in both a streamwise and several cross-stream planes, and (2) the hot nozzle geometry. Tabular forms of the data and computer-aided design (CAD) files of the hot geometry are presented as supplemental files described in Appendix A (TM-20230006779SUPPL1.zip) and Appendix B (TM-20230006779SUPPL2.zip).

Turbulence↗
NASA NTRS2023

NASA Space Environment Analog for Training, Engineering, Science, and Technology (SEATEST) 6 Detailed Final Report

After more than 50 years since the last crewed lunar landing, plans for more missions to the moon are in development. For these missions, efficient and sustainable logistics will be critical. Additionally, innovative methods of cargo transfer to and from a lunar outpost should be considered for successfully establishing a permanent presence on the moon. SEATEST (Space Environment Analog for Training, Engineering, Science, and Technology) is an immersive mission-analogous operational atmosphere where buoyancy effects and supplemental weights can simulate partial gravity conditions similar to those astronauts will experience on the moon. SEATEST 6 took place at the University of Southern California (USC) Wrigley Marine Science Center on Santa Catalina Island from July 18-30, 2023. The analog was used to collect preliminary logistics data on two different offloading conceptual methods (a davit and a zipline) during a simulated lunar mission. Pre-test analysis indicated for a crew of two on a 14-day mission, approximately three Medium Pressurized Logistics Containers (MPLC) sized logistics containers (or a total of 37.5 single Cargo Transfer Bag Equivalents (CTBE)) would be needed to support a mission. A Computer-Aided Design (CAD) analysis was employed on the SEATEST airlock mockup to determine how many logistic containers would fit with two suited crewmembers, don/doff stands, and hatch operations. It was determined that for SEATEST, a total of 15 1.0 Small Pressurized Logistics Containers (SPLCs) and 8 2.0 SPLCs would adequately fit into the approximate 9.5 cubic meter airlock volume. This does not fully represent a complete 14-day logistic supply; however, it does provide a preliminary estimate to initiate design conversations between logistics teams and crew at this early stage of development. Data were collected in eight logistics transfer scenarios over two days with four scenarios per day. Five test subject crew participated in scenarios as pairs. Scenarios included two sizes of logistics containers – 1.0 SPLC (equivalent to a single Cargo Transfer Bag (CTB) and 2.0 SPLC (equivalent to two CTBs). Planed evaluations included the use of a logistics port compared to transfer through an Airlock hatch, offloading methods based on either a davit or a zipline system, choreography of cargo in the airlock to permit ingress and suit doffing, and dust removal protocols for an understanding of the overall impact to transfer ops. Data collected included objective data (task times for conducting overall tasks and subtasks, full audio/video of test activities, and inadvertent “dings” on hardware) and subjective data (crew consensus of: task acceptability and capability assessment ratings related to best practices, considerations, and constraints for EVA-driven logistics transfer ConOps, sim quality of the test environment, and more general debrief comments). The two logistic offloading transfer concepts (davit, zipline) presented both advantages and limitations. The davit’s flexibility in allowing the crew to pick up the containers without physical interaction was well regarded by the crew. Some limitations of select davit hardware components were noted, but the overall concept was acceptable. The zipline system proved to be the most efficient way of moving logistics from the lander to the airlock and eliminated the need for dust operations. However, extended and repetitive lifting of containers to the line could be fatiguing. In conclusion, logistics transfer could hypothetically be achieved without an offloading method; however, the time requirement for such operations would be prohibitive. Results of crew subjective feedback proposed a combined or hybrid davit/zipline method to increase efficiency.

Logistics↗
NASA NTRSDate not supplied

Conceptual Design of a Test Section for a Cryogenic Transfer Line Experiment

This project presents the development of a comprehensive computer-aided design (CAD) model for the Transfer Line test section, which is an upcoming test module for the Flow Boiling and Condensation Experiment (FBCE) aboard the International Space Station. The FBCE aims to serve as the primary platform to study two-phase flow in microgravity, and the Transfer Line module aims to utilize its existing hardware to study cryogenic chilldown; a critical component of cryogenic propellant transfer in space. The CAD model was created using SolidWorks software and includes the test section’s main components: a heat transfer line, a flow visualization line, insulation, high-speed visible imaging, and infrared imaging. The heat transfer line primarily consists of a stainless steel tube that will be heated via Joule heating. The flow visualization line consists of segmented Indium-Titanium-Oxide coated sapphire tubes, which allow for visualization of flow regimes by high-speed and infrared cameras, similar thermal properties as the stainless steel tube, and Joule heating via the ITO coating resistance. Polyether Ether Ketone was used to insulate and encapsulate the two sections. High-speed visible imaging and infrared imaging were also incorporated to view the propagation of fluid during inverted annular flow and map out the thermal profile of the ITO-coated sapphire tube. This model serves as the guiding concept design for the Transfer Line project and will assist the project team during future safety reviews and concept design reviews. Overall, this work is significant in two-phase flow research and offers a promising path towards an established facility for cryogenic transfer line research in microgravity.

Flow boiling↗
NASA NTRS2019

Manufacturing of Thermoset Polyimide Composites by Laser Sintering

Selective Laser Sintering (SLS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the computer-aided design (CAD) model. SLS generally uses thermoplastic polymeric powders such as polyamides. The resultant 3D-printed objects are often weaker in their strength compared to traditionally processed materials, due to their higher porosity. This paper described the process development of using melt-processable imide oligomers terminated with reactive 4-phenylethynylphthalic anhydride (4-PEPA) to conduct laser sintering (LS). The first successful 3D-printing of high temperature RTM370 thermoset polyimide carbon fiber composites were further post-cured to promote additional crosslinking for achieving higher temperature (T g = 370°C) capability. Another novel imide oligomer, RTM385-SLS, formulated with a complex melt viscosity [ƞ*] of ~104-105 poise is also suitable for LS. RTM385-SLS resin powder was mixed with 20-25% of hexagonal boron nitride (h-BN) and subjected to LS to print out “Green” specimens which could be further post-cured to afford a thermally conductive but electrically insulating composites with high T g of 385 °C. The cured composite specimens were then subjected to mechanical testing, thermal conductivity and porosity measurements as well as SEM characterization.

additive Manufacturing↗
DOE OSTI2026

Beam-water Interaction System for PFAS Treatment

Per- and polyfluoroalkyl substances (PFAS) are persistent environmental contaminants that resist conventional water treatment due to the strength of their carbon fluorine bonds. Electron-beam irradiation has shown potential for PFAS degradation; however, its effectiveness is limited by shallow energy penetration, restricting treatment to the upper region of the water surface. This project addresses this limitation through the design of a compact mixing chamber and recirculation system to enhance surface renewal and improve treatment efficiency. The system, constrained to approximately 10 cm 20 cm 20 cm, was developed using computer-aided design, computational fluid dynamics (CFD), and MATLAB-based hydraulic analysis to evaluate flow behavior, head loss, and pump compatibility. A perforated-baffle geometry and controlled flow range of 1 3 GPM were implemented to promote uniform mixing while maintaining a stable free surface for electron-beam exposure. Modeling results indicate improved flow distribution and reduced dead zones, supporting more consistent interaction between contaminated water and the beam. The final design enhances hydrodynamic performance within system constraints, contributing to scalable electron-beam water treatment technologies for improved PFAS degradation.

Ramos, Gerardo [Northern Illinois U.]↗
DOE OSTI2026

Test cavity and Iris-to-Coax transition for tuning and high-power verification of SNS DTL iris couplers

The Spallation Neutron Source (SNS) Drift Tube Linac (DTL) employs iris couplers to efficiently deliver RF power into the accelerating structure. To support the development, tuning, and high‑power conditioning of these couplers prior to installation in the actual DTLs, a dedicated test cavity and an iris‑to‑coaxial transition structure have been designed. This work presents the electromagnetic design, simulation, and optimization of the test setup, enabling precise characterization of the iris coupler’s performance. The transition structure allows for tuning of the iris opening dimensions without requiring a waveguide taper or full‑size waveguide transitions, while maintaining impedance matching between the coaxial feed and the iris geometry to minimize reflection and power loss. During low‑power tests, the iris opening di-mensions can be evaluated using the iris‑to‑coax transi-tion attached to the test cavity. For high‑power condi-tioning, full‑size waveguides with ceramic vacuum win-dows are connected to the test cavity to replicate opera-tional conditions. Key design parameters were optimized using computer-aided simulation, and sensitivity studies were conducted to assess the impact of mechanical toler-ances on RF performance. The resulting test platform provides a reliable and efficient means for tuning and validating iris couplers, contributing to improved opera-tional stability in the SNS DTL.

Lee, Sung-Woo [ORNL] (ORCID:000000030915835X)↗
DOE OSTI2026

Design and Characterization of the 162.5 MHz RF Component Layout for Fermilab's PIP-II Reference Line

The Proton Improvement Plan II (PIP-II) Reference Line at Fermi National Accelerator Laboratory distributes phase-stable radio-frequency (RF) signals throughout the accelerator. PIP-II requires stable timing and phase reference signals so its accelerating cavities transfer energy to the particle beam at the correct point in each RF cycle. The full system includes 162.5, 325, and 650 MHz sections corresponding to the frequency sections of the PIP-II Linac, with this project focusing on the 162.5 MHz section. The Reference Line must provide a phase stable source signal while responding to phase changes caused by environmental conditions or system drift. Its RF components will be mounted on aluminum heat plates inside a temperature controlled enclosure to further limit temperature-driven phase changes. To prepare the system for manufacture, the project reviewed component functions and dimensions, developed a computer-aided design (CAD) model, and arranged the hardware to support short cable paths, grounding, fastener access, and maintenance. Several full scale, three dimensional printed prototypes allowed the available components to be mounted and inspected. These fit checks revealed mechanical conflicts and guided revisions to component placement, countersink geometry, labeling, and plate thickness. Electrical characterization was also performed on selected RF hardware to compare its measured behavior with the performance metrics that were set for our design. Overall, the project produced a manufacturable 162.5 MHz layout, physical fit-check prototypes, and documented electrical measurements that support review before metal fabrication. The 325 and 650 MHz layouts remain future work because they require additional minor mechanical changes.

Subedi, Harsheet [Unlisted, US, CA] (ORCID:0009000↗
DOE OSTI2025

A simple introduction to the SiMPL method for density-based topology optimization

We introduce a novel method for solving density-based topology optimization problems: Sigmoidal Mirror descent with a Projected Latent variable (SiMPL). The SiMPL method (pronounced as “the simple method”) optimizes a design using only first-order derivative information of the objective function. The bound constraints on the density field are enforced with the help of the (negative) Fermi–Dirac entropy, which is also used to define a non-symmetric distance function called a Bregman divergence on the set of admissible designs. This Bregman divergence leads to a simple update rule that is further simplified with the help of a so-called latent variable. Because the SiMPL method involves discretizing the latent variable, it produces a sequence of pointwise-feasible iterates, even when high-order finite elements are used in the discretization. Numerical experiments demonstrate that the method outperforms other popular first-order optimization algorithms. In conclusion, to outline the general applicability of the technique, we include examples with (self-load) compliance minimization and compliant mechanism optimization problems.

Calculus of Variations and Optimization↗
DOE OSTI2025

A Simple, Scalable Large Deformation Solid Mechanics Implementation in the MOOSE Framework

This article describes a large deformation solid mechanics solver implemented as part of the freely available and open source MOOSE finite element simulation framework. The article documents the choices made in developing the solid mechanics framework and describes novel formulations for the gradient operator and constitutive modeling framework made to simplify implementations of different coordinate systems, stabilized gradient operators, and different constitutive model inputs and outputs. In the process, the article describes a new formulation that casts objective integration of the Cauchy stress as a linear transformation of the small stress rate. Finally, the article presents key implementation details and examines the parallel efficiency of the solid mechanics solver implemented in MOOSE. The implementation retains a good weak scaling efficiency beyond 1,000 parallel processes. The article includes a discussion of the factors limiting the parallel efficiency of implicit, large deformation solid mechanics codes on current high-performance computers, with the main current limitation being the scalability of the algebraic multigrid methods used to solve the linearized equilibrium equations.

Applied computing → Computer-aided design↗
NASA NTRS2001

Creation and utilization of a World Wide Web based space radiation effects code: SIREST

In order for humans and electronics to fully and safely operate in the space environment, codes like HZETRN (High Charge and Energy Transport) must be included in any designer's toolbox for design evaluation with respect to radiation damage. Currently, spacecraft designers do not have easy access to accurate radiation codes like HZETRN to evaluate their design for radiation effects on humans and electronics. Today, the World Wide Web is sophisticated enough to support the entire HZETRN code and all of the associated pre and post processing tools. This package is called SIREST (Space Ionizing Radiation Effects and Shielding Tools). There are many advantages to SIREST. The most important advantage is the instant update capability of the web. Another major advantage is the modularity that the web imposes on the code. Right now, the major disadvantage of SIREST will be its modularity inside the designer's system. This mostly comes from the fact that a consistent interface between the designer and the computer system to evaluate the design is incomplete. This, however, is to be solved in the Intelligent Synthesis Environment (ISE) program currently being funded by NASA.

NASA Discipline Radiation Health↗
NASA NTRS1993

CASRE ?? Eay-to-Use Software Reliability Measurement Tool

This paper describes the implementation of a software reliability measurement tool, CASRE, that incorporates the methematical modeling capabilities of the public domain tool SMERFS, and is being implemented in a Microsoft Windows environment.

software reliability Computer-Aided Software Relia↗
NASA NTRS2007

Interfacing WIPL-D with Mechanical CAD Software

of almost any popular CAD format, e.g. IGES, Parasolid, DXF, ACIS etc. The solid models are processed (simplified) and meshed in GiD(R), and then converted into WIPL-D Pro input file by simple Fortran or Matlab code. This algorithm allows the user to control the mesh of imported geometry, and to assign electric p~perties to metalic and dielectric surfaces. Implementation of the algorithm is demonstrated by examples obtained from the NASA Discovery mission, Phoenix Lander 2008. Results for radiation pattern of Phoenix Lander UHF relay antenna with effect of Martian surface, both simulated in WIPL-D Pro and measured, are shown for comparison.

method of moments (MoM)↗