Search NASA⌕ Search

SEARCH · Search NASA

Results for “friction data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Sea Surface Slope Statistics for Intermediate and Shore Scale Ocean Waves Measured Using a Low-Altitude Aircraft

Ocean surface remote sensing techniques often rely on scattering or emission linked to shorter- scale gravity-capillary ocean wavelets. However, it is increasingly apparent that slightly longer wavelengths of O(10 to 500 cm) are vital components in the robust sea surface description needed to link varied global remote sensing data sets. This paper describes a sensor suite developed to examine sea surface slope variations in the field using an aircraft flying at very low altitude (below 30 m) and will also provide preliminary measurements detailing changes in slope characteristics versus sea state and friction velocity. Two-dimensional surface slope is measured using simultaneous range measurements from three compact short-range laser altimeters mounted in an equilateral triangle arrangement with spacing of about 1 m. In addition, all three lasers provide independent wave elevation profiles after GPS-aided correction for aircraft altitude. Laser range precision is 1 cm rms while vertical motion correction is 15 cm rms. The measurements are made along-track at approximately 1 m intervals setting the spatial scale of the measurement to cover waves of intermediate to long scale. Products available for this array then include surface elevation, two-dimensional slope distribution, and the cross- and along-track 1-D slope distributions. To complement the laser, a down-looking mm-wave radar scatterometer is centered within the laser array to measure radar backscatter simultaneously with the laser slope. The radar's footprint is nominally 1 m in diameter. Near-vertical radar backscatter is inversely proportional to the small-scale surface slope variance and to the tilt of the underlying (laser-measured) surface facet. Together the laser and radar data provide information on wave roughness from the longest scales down to about 1 cm. These measurements are complemented by aircraft turbulence probe data that provides robust surface flux information.

Vandemack, Douglas↗
NASA NTRS1982

The dryout region in frictionally heated sliding contacts

Some conditions under which boiling and two-phase flow can occur in or near a wet sliding contact are determined and illustrated. The experimental apparatus consisted of a tool pressed against an instrumented slider plate and motion picture sequences at 4000 frames/sec. The temperature and photographic data demonstrated surface conditions of boiling, drying, trapped gas evolution (solutions), and volatility of fluid mixture components. The theoretical modeling and analysis are in reasonable agreement with experimental data.

Hendricks, R. C.↗
NASA NTRS1982

The dryout region in frictionally heated sliding contacts

Some conditions under which boiling and two-phase flow can occur in or near a wet sliding contact are determined and illustrated. The experimental apparatus consisted of a tool pressed against an instrumented slider plate and motion picture sequences at 4000 frames/sec. The temperature and photographic data demonstated surface conditions of boiling, dry, trapped gas evolution (solutions), and volatility of fluid mixture components. The theoretical modeling and analysi are in reasonable agreement with experimental data. Previously announced in STAR as N82-28574

Hendricks, R. C.↗
NASA NTRS1984

Durable solid lubricant coatings for foil gas bearings to 315 deg C

The durability and friction characteristics of bonded solid lubricant films on compliant gas bearings were measured. Coating compositions, which were judged to be suitable for use to at least 315 C, were selected for this study. Most of the data were obtained with polyimide-bonded graphite fluoride coatings and with silicate-bonded graphite coatings. These coatings were applied to the bore of Inconel 750 foil bearings. The journals were A286 stainless steel, with a rms surface finish of 0.2 microns. The foils were subjected to repeated start/stop cycles under a 14 kPa (2 psi) bearing unit load. Sliding contact occurred during lift-off and coast down at surface velocities less than 6 m/s (3000 rpm). Testing continued until 9000 cycles were accumulated or until a rise in starting torque indicated that the coating had failed. The coatings were evaluated in the temperature range from 25 C to 315 C. Comparisons in coating performance as well as discussions of their properties and methods of application are given.

Wagner, R. C.↗
NASA NTRS1987

Investigation of low-speed turbulent separated flow around airfoils

Described is a low-speed wind tunnel experiment to measure the flowfield around a two-dimensional airfoil operating close to maximum lift. Boundary layer separation occurs on the upper surface at x/c=0.85. A three-component laser velocimeter, coupled with a computer-controlled data acquisition system, was used to obtain three orthogonal mean velocity components and three components of the Reynolds stress tensor in both the boundary layer and wake of the airfoil. Pressure distributions on the airfoil, skin friction distribution on the upper surface of the airfoil, and integral properties of the airfoil boudary layer are also documented. In addition to these near-field flow properties, static pressure distributions, both upstream and downstream from the airfoil and on the walls of the wind tunnel, are also presented.

Wadcock, Alan J.↗
NASA NTRS1992

Data reduction formulas for the 16-foot transonic tunnel: NASA Langley Research Center, revision 2

The equations used by the 16-Foot Transonic Wind Tunnel in the data reduction programs are presented in nine modules. Each module consists of equations necessary to achieve a specific purpose. These modules are categorized in the following groups: (1) tunnel parameters; (2) jet exhaust measurements; (3) skin friction drag; (4) balance loads and model attitudes calculations; (5) internal drag (or exit-flow distribution); (6) pressure coefficients and integrated forces; (7) thrust removal options; (8) turboprop options; and (9) inlet distortion.

Mercer, Charles E.↗
DOE OSTI2023

Utah FORGE: Fault Reactivation Through Fluid Injection Induced Seismicity Laboratory Experiments

Included are results from shear reactivation experiments on laboratory faults pre-loaded close to failure and reactivated by the injection of fluid into the fault. The sample comprises a single-inclined-fracture (SIF) transecting a cylindrical sample of Westerly granite. All experiments are conducted at ambient temperature and follow a similar protocol: (i) application of confining stresses (3MPa) on the fault fully saturated with DI water, (ii) shear-mobilization through the increase of axial loading at a constant displacement rate until a post-peak steady-state condition is reached, (iii) reduction of axial loading and related shear stress to a prescribed fraction of the peak steady-state frictional strength (typically 60% to 90%, representing intermediate to high magnitudes) and (iv), fault reactivation triggered by a stepwise increase of pore pressure on the fault in 0.1 MPa increments held constant for 1-5 minutes. Mechanical data from three ISCO pumps connected to a Temco pressure vessel measure axial, confining, and fault-related parameters, including fluid pressure (kPa), fluid flow rate (mL/min), and axial displacement (mm). See included code for initial data analysis and visualization for select experiments. Resource names represent experiment numbers found in the "Read Me" file, which describes each experimental setup and parameters.

15 GEOTHERMAL ENERGY↗
NASA NTRS1976

Re-examination of compliant wall experiments in air with water substrates

A possible alternative explanation is proposed for compliant wall drag reductions measured in previous investigations. Standing waves were observed to form on the surfaces of compliant wall models in air with water substrates as the freestream velocity was increased from 15 to 30 m/s. These waves resembled sine waves with half of the wave protruding over the upstream portion of the model and the other half being recessed over the downstream end of the model. These data coupled with results of recent drag reduction experiments suggest that standing waves could have caused a shift in the model center of gravity creating a bending moment that was interpreted as a reduction in the skin friction drag.

Hefner, J. N.↗
NASA NTRS1984

The National Transonic Facility - A research perspective

The capabilities of the National Transonic Facility (NTF) at NASA-Langley and its impact on aerodynamics investigations are surveyed. The fan-driven, closed-circuit transonic wind tunnel has an 8.2 sq ft slotted test section. Trials can be run from Mach 0.2-1.2, pressures of 1-8.9 atm, and temperatures of -320 to 150 F using nitrogen as the working gas. Instrumentation has been developed for monitoring force, pressure, attitude, deformation, temperature, skin friction, flow transition, and flow velocity as well as visualizing flows around the models. Pressures of 15-130 psi are available, as are Re up to 120 million at Mach 1. Correlations are being made with flight data from the Shuttle, 767, X-29A, and TACT aircraft for real-world extrapolations. The NTF, when combined with computational fluid dynamics techniques, will permit testing of aerodynamically sophisticated shapes while narrowing the design goals for each model during basic research in fluid mechanics, transport, and aerodynamic phenomena.

Campbell, J. F.↗
NASA NTRS1984

An experimental investigation of two-dimensional thrust augmenting ejectors, part 2

The flow-field within a two-dimensional thrust augmenting ejector has been documented experimentally. Results are presented on the mean velocity field and the turbulent correlations by Laser Doppler Velocimeter, surface pressure distribution, surface temperature distribution, and thrust performance for two shroud geometries. The maximum primary nozzle pressure ratio tested was 3.0. The tests were conducted at primary nozzle temperature ratios of 1.0, 1.8 and 2.7. Two ejector characteristic lengths have been identified based on the dynamics of the ejector flow field, i.e., a minimum length L sub m below which no significant mixing occurs, and a critical length L sub c associated with the development of U'V' correlation in the ejector. These characteristic lengths divide the ejector flow field into three distinctive regions: the entrance region where there is no direct interaction between the primary flow and the ejector shroud; the interaction region where there is an increased momentum of induced flow near the shroud surface; and a pipe flow region characterized by an increased skin friction where x is the distance downstream from the ejector inlet. The effect of the coflowing induced flow has been shown to produce inside the ejector a centerline velocity that has increased over the free-jet data.

Bernal, L.↗
NASA NTRS1992

Oscillating-flow regenerator test rig: Woven screen and metal felt results

We present correlating expressions, in terms of Reynolds or Peclet numbers, for friction factors, Nusselt numbers, enhanced axial conduction ratios, and overall heat flux ratios in four porous regenerator samples representative of stirling cycle regenerators: two woven screen samples and two random wire samples. Error estimates and comparison of data with others suggest our correlations are reliable, but we need to test more samples over a range of porosities before our results will become generally useful.

Gedeon, D.↗
NASA NTRS2001

Innovative Technologies for a Space Station Microgravity Furnace

Several Innovations were developed for a high gradient directional solidification vacuum furnace with quench capability, called the Quench Module Insert. The QMI hot zone employs advanced heater elements in a multiple zone configuration and uses a novel instrumentation approach for temperature control. A fiber interface material provides a low friction, high heat extraction interface between a reconfigurable cold zone and the science sample. The quench utilizes a metal phase change to provide rapid, resource efficient quenching of science samples. This paper provides conceptual details and performance data on these innovations.

Carswell, B.↗
NASA NTRS2003

Nonlinear Dynamics of the Superfluid Transition: What may We learn on orbit?

Linear response (specifically, Fourier's Law) in He-4 has been observed to fail in heat flow experiments near the superfluid transition. A detailed analysis of the data suggests that the hydrostatic pressure gradient across the helium column limits the divergence of the correlation length in our earth-based experiments. This is consistent with other observations, such as the surprising lack of mutual friction and hysteresis near the superfluid transition, and a 'rounding' of the transition that appears to be independent of heat flux in the low heat flux limit. I will discuss these unusual results from earth-based measurements, and will show predictions for the very different results that may result when we make our measurements on orbit as part of the M1 Mission of the Low- Temperature, Microgravity Physics Facility. This work has been funded by the Fundamental Physics Discipline within the Physical Sciences Research Office of NASA, and is conducted by the DYNAMX (UNM) and CQ (Caltech) Groups, with assistance from the Low Temperature Science and Quantum Sensors Group at JPL.

Duncan, Rob↗
NASA NTRSDate not supplied

LS-DYNA User-Defined Internal Ballistic Modeling

- LS-DYNA Explicit Finite Element Analysis software and CADPROG Internal Ballistic Analysis code are integrated as a single modeling tool to analyze pyro-mechanical devices. - Combining these two codes allows the ballistic calculations to be performed without modeling the propellant in an FEA mesh. At each LS-DYNA time step, CADPROG is analytically run using the kinematic data (stroke, velocity, chamber volume) fed back from the LS-DYNA simulation. Calculated pressure is then applied to a piston or any applicable surface mesh in LS-DYNA model interactively. -All external loads such as friction, damping loads, assisting/resisting loads, locking/unlocking loads are modeled in LS-DYNA and coupled with pressure loads from CADPROG to create a fully defined equation of motion -Both codes are written in Fortran 77. CADPROG is inserted in LS-DYNA source code as a user-defined subroutine and re-compiled to generate a custom executable.

pyrotechnics↗
DOE OSTI2022

Physics-Informed and Data-Driven Prediction of Residual Stress in Three-Dimensional Machining

Efficient and reliable prediction of machining-induced residual stress (RS) is a key requirement for truly integrated computational materials engineering (ICME). Currently available process modeling approaches, including empirical, analytical, and numerical methodologies lack predictive power and require substantial calibration and validation data. Moreover, most model-based approaches consider only two-dimensional (2D) (i.e., orthogonal), cutting processes. Meanwhile, industrial processes such as milling, turning, and drilling are inherently three-dimensional (3D). The present work attempts to bridge the gap between 2D and 3D through careful consideration of the process physics, including geometric, kinematic, and size-effect constraints to realize robust prediction of how RS develops in 3D machining. Using a novel in-situ experimental technique and digital image correlation (DIC) to determine equivalent Hertzian contact widths, contact pressures, and friction coefficients, the proposed methodology leverages a discretized conversion algorithm that includes multi-pass shakedown effects. This paper presents a semi-analytical model to predict machining-induced RS in 3D turning operations, which are used representatively for 3D processes more generally. Rather than follow a ‘brute force’ 3D FEM approach or conduct countless experiments to train a purely data-driven machine learning algorithm, the proposed approach builds on previous 2D modeling work. Through careful consideration of the process physics, including complex geometry/kinematic considerations of 3D turning, the authors demonstrated an experimentally calibrated approach, as well as validation based on published RS data. Model predictions and previously published measurement data of RS depth profiles for turning of Inconel 718 were compared for a range of process parameters. Correlation between the proposed 3D model and validation data was found to be within the margin of experimental error for most conditions. The proposed model appears to capture the overall behavior of 3D RS depth profiles with acceptable accuracy, particularly the key metrics of near-surface stress, peak stress magnitude and location, as well as overall stress profile depth. This report presents a physics-informed, data-driven approach for efficient calibration of a 2D model for machining-induced RS through DIC analysis of in-situ characterized subsurface displacement fields.

42 ENGINEERING↗
NASA NTRS1971

Possible flow regimes of adiabatic one-dimensional compressible fluid flow with friction in convergent and divergent ducts.

An analytical solution for the compressible one-dimensional flow in convergent and divergent ducts with friction is obtained. It is found that a nondimensional parameter, N, can be formed using the friction factor, duct half-angle and the ratio of specific heats of the gas. Seven flow regimes are describable with the solution, based on certain bounds on the magnitude of N. The regimes are discussed and corollary data are presented graphically.

Shouman, A. R.↗
NASA NTRS1973

Design for pressure regulating components

The design development for Pressure Regulating Components included a regulator component trade-off study with analog computer performance verification to arrive at a final optimized regulator configuration for the Space Storable Propulsion Module, under development for a Jupiter Orbiter mission. This application requires the pressure regulator to be capable of long-term fluorine exposure. In addition, individual but basically identical (for purposes of commonality) units are required for separate oxidizer and fuel pressurization. The need for dual units requires improvement in the regulation accuracy over present designs. An advanced regulator concept was prepared featuring redundant bellows, all metallic/ceramic construction, friction-free guidance of moving parts, gas damping, and the elimination of coil springs normally used for reference forces. The activities included testing of actual size seat/poppet components to determine actual discharge coefficients and flow forces. The resulting data was inserted into the computer model of the regulator. Computer simulation of the propulsion module performance over two mission profiles indicated satisfactory minimization of propellant residual requirements imposed by regulator performance uncertainties.

Wichmann, H.↗
NASA NTRS1977

ALSEP-quasar differential VLBI

A program of ALSEP-quasar very-long-baseline interferometry (VLBI) is being carried out. These observations employ primarily a 'four-antenna' technique whereby simultaneous observations with two antennas at each end of an intercontinental baseline are used to derive the differential interferometric phase between a compact extragalactic radio source (usually a quasar) and a number of ALSEP transmitters on the lunar surface. A continuous ALSEP-quasar differential phase history over a period of a few hours will lead to milliarcsecond angular accuracy in measuring the lunar position against the quasar reference frame if suitable calibration measurements are obtained. Development of this application of the four-antenna technique has been underway for more than a year and is producing high-quality data utilizing Deep Space Network stations. These high-accuracy observations are of value to tie the lunar ephemeris to a nearly inertial extragalactic reference frame, to test gravitational theories, and to measure the earth-moon tidal friction interaction.

Slade, M. A.↗