SEARCH · Search NASA

Results for “linear flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

All sources NASA NTRS DOE OSTI

NASA NTRS2002

Boundary Layer Transition on Slender Cones in Conventional and Low Disturbance Mach 6 Wind Tunnels

An experimental investigation was conducted on a 5-degree half-angle cone and a 5-degree half-angle flared cone in a conventional Mach 6 wind tunnel to examine the effects of facility noise on boundary layer transition. The influence of tunnel noise was inferred by comparing transition onset locations determined from the present test to that previously obtained in a Mach 6 low disturbance quiet tunnel. Together, the two sets of experiments are believed to represent the first direct comparison of transition onset between a conventional and a low disturbance wind tunnel using a common test model and transition detection technique. In the present conventional hypersonic tunnel experiment, separate measurements of heat transfer and adiabatic wall temperatures were obtained on the conical models at small angles of attack over a range of Reynolds numbers, which resulted in laminar, transitional, and turbulent flow. Smooth model turbulent heating distributions are compared to that obtained with transition forced via discrete surface roughness. The model nosetip radius was varied to examine the effects of bluntness on transition onset. Despite wall to total temperature differences between the transient heating measurements and the adiabatic wall temperature measurement, the two methods for determining sharp cone transition onset generally yielded equivalent locations. In the 'noisy' mode of the hypersonic low disturbance tunnel, transition onset occurred earlier than that measured in the conventional hypersonic tunnel, suggesting higher levels of freestream acoustic radiation relative to the conventional tunnel. At comparable freestream conditions, the transition onset Reynolds number under low disturbance conditions was a factor of 1.3 greater than that measured on flared cone in the LaRC conventional hypersonic tunnel and a factor of 1.6 greater that the flared cone run in the low disturbance tunnel run 'noisy'. Navier-Stokes mean flow computations and linear stability analysis were conducted to assess the experimental results and have indicated N factors associated with sharp flared cone transition onset to be approximately a factor of 2 lower than that inferred from the corresponding low disturbance tunnel measurements.

Horvath, Thomas J.↗

NASA NTRS2003

Nonlinear Aeroacoustics Computations by the Space-Time CE/SE Method

The Space-Time Conservation Element and Solution Element Method, or CE/SE Method for short, is a recently developed numerical method for conservation laws. Despite its second order accuracy in space and time, it possesses low dispersion errors and low dissipation. The method is robust enough to cover a wide range of compressible flows: from weak linear acoustic waves to strong discontinuous waves (shocks). An outstanding feature of the CE/SE scheme is its truly multi-dimensional, simple but effective non-reflecting boundary condition (NRBC), which is particularly valuable for computational aeroacoustics (CAA). In nature, the method may be categorized as a finite volume method, where the conservation element (CE) is equivalent to a finite control volume (or cell) and the solution element (SE) can be understood as the cell interface. However, due to its careful treatment of the surface fluxes and geometry, it is different from the existing schemes. Currently, the CE/SE scheme has been developed to a matured stage that a 3-D unstructured CE/SE Navier-Stokes solver is already available. However, in the present review paper, as a general introduction to the CE/SE method, only the 2-D unstructured Euler CE/SE solver is chosen and sketched in section 2. Then applications of the 2-D and 3-D CE/SE schemes to linear, and in particular, nonlinear aeroacoustics are depicted in sections 3, 4, and 5 to demonstrate its robustness and capability.

Loh, Ching Y.↗

NASA NTRS1985

The Goertler Instability on an Airfoil

Goertler vortices arise in boundary layers along concave surfaces due to centrifugal effects. This paper presents some results of an experiment conducted to study the development of these vortices on an airfoil with a pressure gradient in the concave region where an attached laminar boundary layer was insured with suction through a perforated panel. The sublimating chemical technique was used to visualize Goertler vortices and the velocity field was measured by laser velocimetry. The vortex wavelength clearly varied with Goertler number as predicted by linear theory. Both flow visualization and velocity measurements indicated vortex damping in the convex zone. Secondary instability was observed at the higher Goertler numbers.

Mangalam, S. M.↗

NASA NTRS2016

Multiparameter Flowfield Measurements in High-Pressure, Cryogenic Environments Using Femtosecond Lasers

Femtosecond laser electronic excitation tagging (FLEET) and Rayleigh scattering (RS) from a femtosecond laser are demonstrated in the NASA Langley 0.3-m Transonic Cryogenic Tunnel (TCT). The measured signals from these techniques are examined for their thermodynamic dependencies in pure nitrogen. The FLEET signal intensity and signal lifetimes are found to scale primarily with the gas density, as does the RS signal. Several models are developed, which capture these physical behaviors. Notably, the FLEET and Rayleigh scattering intensities scale linearly with the flow density, while the FLEET signal decay rates are a more complex function of the thermodynamic state of the gas. The measurement of various flow properties are demonstrated using these techniques. While density was directly measured from the signal intensities and FLEET signal lifetime, temperature and pressure were measured using the simultaneous FLEET velocity measurements while assuming the flow had a constant total enthalpy. Measurements of density, temperature, and pressure from the FLEET signal are made with accuracies as high as 5.3 percent, 0.62 percent, and 6.2 percent, respectively, while precisions were approximately 10 percent, 0.26 percent, and 11 percent for these same quantities. Similar measurements of density from Rayleigh scattering showed an overall accuracy of 3.5 percent and a precision of 10.2 percent over a limited temperature range (T greater than 195 K). These measurements suggest a high degree of utility at using the femtosecond-laser based diagnostics for making multiparameter measurements in high-pressure, cryogenic environments such as large-scale TCT facilities.

Burns, Ross A.↗

NASA NTRS2018

Toward Simultaneous Velocity and Density Measurements Using FLEET and Laser Rayleigh Scattering

Femtosecond laser electronic excitation tagging (FLEET) velocimetry and laser Rayleigh scattering are conducted concurrently and are evaluated for their suitability to measure velocity and density simultaneously in NASA Langley’s 0.3-m Transonic Cryogenic Tunnel. FLEET velocimetry measurements are shown to be accurate to within 1.5 percent of the measured velocity throughout the facility testing envelope and exhibit a zero-velocity precision of 0.4 m/s. Rayleigh scattering density measurements indicate a characteristically linear dependence on flow density while having an accuracy within 5.4 percent of the measured density and a precision less than or equal to 6 percent. The preliminary assessment indicates that the joint technique would be advantageous for deployment in high-pressure, cryogenic test facilities.

Burns, Ross A.↗

NASA NTRS1987

Application of stability theory to laminar flow control - Progress and requirements

Paper briefly summarizes the current status of linear stability theory as applied to laminar flow control for aerodynamics. Results indicate that the conventional 'N factor' method of correlating stability theory and transition has a broad application range, including low- and high-speeds, two- and three-dimensional mean flow and TS, Gortler and crossflow disturbance modes. Linear theory is particularly applicable to the laminar flow control problem as, for system efficiency, control must be exercised and disturbances maintained in the linear regime. Current areas of concern for LFC, which require further stability theory research, include TS-crossflow interaction, combined disturbance fields (roughness, waviness, noise) and suction-induced disturbances. Some results on wave-interactions are presented.

Bushnell, D. M.↗

NASA NTRS1992

Airfoil wake and linear theory gust response including sub and superresonant flow conditions

The unsteady aerodynamic gust response of a high solidity stator vane row is examined in terms of the fundamental gust modeling assumptions with particular attention given to the effects near an acoustic resonance. A series of experiments was performed with gusts generated by rotors comprised of perforated plates and airfoils. It is concluded that, for both the perforated plate and airfoil wake generated gusts, the unsteady pressure responses do not agree with the linear-theory gust predictions near an acoustic resonance. The effects of the acoustic resonance phenomena are clearly evident on the airfoil surface unsteady pressure responses. The transition of the measured lift coefficients across the acoustic resonance from the subresonant regime to the superresonant regime occurs in a simple linear fashion.

Henderson, Gregory H.↗

NASA NTRS1987

Amorphous silicon deposition diagnostics using coherent anti-Stokes Raman spectroscopy

This paper reports on an in situ silicon deposition process diagnostics, using CARS performed at state-of-the-art a-Si:H film deposition conditions in a reactor designed for a-Si:H solar cell fabrication. The diagnostics procedure measures the silane depletion in an RF plasma as a function of the silane flow rate (where the relationship is linear between 50-percent depletion, at a flow rate of 5.6 sccm, and about 8-percent depletion, at 80 sccm) and the RF power (where the silane depletion is linearly dependent on the RF power in the region of 4 to 12 W). The linear RF power dependence of the silane depletion is considered to be consistent with the mechanism of silane decomposition primarily by electron impact dissociations, while the flow rate dependence is interpreted in terms of the residence time of the SiH4 molecules in the glow discharge region, where an increase of the residence time at a low flow rate results in a high depletion ratio.

Shing, Y. H.↗

NASA NTRS1953

Steady vibrations of wing of circular plan form

This paper treats the problem of determining the lift, moment, and induced drag of a thin wing of circular plan form in uniform incompressible flow on the basis of linearized theory. As contrasted to a similar paper by Kinner, in which the acceleration potential method was used, the present paper utilizes the concept of the velocity potential. Calculations of the lift and moment are presented for several deformed shapes. It is shown that considerable deviations exist between the strip theory analysis and the more exact theory. The lift, moment, and induced drag are also determined for a harmonically oscillatory circular plan form wing. As contrasted to a similar paper by Schade, in which the acceleration potential method was used, the present paper utilizes the concept of the velocity potential. Expressions for lift, moment, and induced drag are given and finally specialized to the case of a slowly oscillating circular wing.

FLUTTER - WINGS↗

NASA NTRS1985

The Goertler vortex instability mechanism in three-dimensional boundary layers

The two-dimensional boundary layer on a concave wall is centrifugally unstable with respect to vortices aligned with the basic flow for sufficiently high values of the Goertler number. However, in most situations of practical interest the basic flow is three-dimensional and previous theoretical investigations do not apply. The linear stability of the flow over an infinitely long swept wall of variable curvature is considered. If there is no pressure gradient in the boundary layer the instability problem can always be related to an equivalent two-dimensional calculation. However, in general, this is not the case and even for small values of the crossflow velocity field dramatic differences between the two and three-dimensional problems emerge. When the size of the crossflow is further increased, the vortices in the neutral location have their axes locally perpendicular to the vortex lines of the basic flow.

Hall, P.↗

NASA NTRS1987

Star formation in X-ray cluster cooling flows

The basic equations for X-ray cluster cooling flows, including the effects of star formation, are derived. It is confirmed that cooling flows are thermally unstable, and it is found that the fastest-growing linear perturbations in the flow are radial, comoving, and isobaric. A local approximation for the star formation rate is developed which allows analytic solutions to be found for both isobaric and gravity-dominated cooling flows. These solutions are used to show how star formation reduces the gas density, thereby lowering the cooling rate, which raises the gas temperature relative to the non-star-forming case. The analytic solutions are also used to estimate the spatial distribution of newly formed stars. It is found that star formation must proceed at a nearly maximal rate if isothermal mass profiles are to result.

White, Raymond E., III↗

NASA NTRS1981

Accuracy and convergence of a finite element algorithm for laminar boundary layer flow

The Galerkin-weighted residuals formulation is employed to derive an implicit finite element solution algorithm for a generally non-linear initial-boundary value problem. Solution accuracy and convergence with discretization refinement are quantized in several error norms, for the non-linear parabolic partial differential equation system governing laminar boundary layer flow, using linear, quadratic and cubic functions. Richardson extrapolation is used to isolate integration truncation error in all norms, and Newton iteration is employed for all equation solutions performed in double-precision. The mathematical theory supporting accuracy and convergence concepts for linear elliptic equations appears extensible to the non-linear equations characteristic of laminar boundary layer flow.

Soliman, M. O.↗

NASA NTRS2022

The Harmonic Linearized Navier-Stokes Equations for Transition Prediction in Three-Dimensional Flows

The conventional method to predict the onset of laminar-turbulent transition in convectively unstable boundary-layer flows is based on the logarithmic amplification ratio, the so-called N-factor, of the linear instability waves. To calculate the N-factor, the flow variables are decomposed into a laminar basic state solution and the linear disturbances, which are assumed to be harmonic in time. The most commonly used linear stability analysis approaches include the locally parallel linear stability theory (LST) and the nonlocal, weakly nonparallel parabolized stability equations (PSE). However, these methods do not account for strong streamwise gradients that are encountered in several configurations of interest, such as those in the vicinity of roughness elements, steps, gaps, or corners. To compute the linear evolution of disturbances along such strongly nonparallel regions, the harmonic linearized Navier-Stokes equations (HLNSE) need to be solved. The discretization of the HLNSE for spanwise/azimuthally inhomogeneous laminar basic states yields a linear system of complex arithmetic with a leading dimension of the order of 10^(7) to 10^(8) even in relatively simple flows. A combined multithread and multiprocessor algorithm is implemented for the direct solution of such linear systems. Results for a supersonic boundary layer over a three-dimensional roughness patch show good agreement with experimental measurements when the evolution of the instability waves over the roughness patch is included via the HLNSE. Additionally, inflow-resolvent analysis based on the HLNSE for discrete-roughness-induced disturbances in the nose tip of a blunt cone at Mach 6 demonstrates the importance of including the disturbance amplification along the near vicinity of the roughness element and separation region.

Boundary Layer Stability↗

NASA NTRS2010

Traffic Flow Management Using Aggregate Flow Models and the Development of Disaggregation Methods

A linear time-varying aggregate traffic flow model can be used to develop Traffic Flow Management (tfm) strategies based on optimization algorithms. However, there are no methods available in the literature to translate these aggregate solutions into actions involving individual aircraft. This paper describes and implements a computationally efficient disaggregation algorithm, which converts an aggregate (flow-based) solution to a flight-specific control action. Numerical results generated by the optimization method and the disaggregation algorithm are presented and illustrated by applying them to generate TFM schedules for a typical day in the U.S. National Airspace System. The results show that the disaggregation algorithm generates control actions for individual flights while keeping the air traffic behavior very close to the optimal solution.

Sun, Dengfeng↗

NASA NTRS1989

Effect of wall cooling on the stability of compressible subsonic flows over smooth humps and backward-facing steps

The effect of wall cooling on the two-dimensional linear stability of subsonic flows over two-dimensional surface imperfections is investigated. Results are presented for flows over smooth humps and backward-facing steps with Mach numbers up to 0.8. The results show that, whereas cooling decreases the viscous instability, it increases the shear-layer instability and hence it increases the growth rates in the separation region. The coexistence of more than one instability mechanism makes a certain degree of wall cooling most effective. For the Mach numbers 0.5 and 0.8, the optimum wall temperatures are about 80 pct and 60 pct of the adiabatic wall temperature, respectively. Increasing the Mach number decreases the effectiveness of cooling slightly and reduces the optimum wall temperature.

Al-Maaitah, Ayman A.↗

NASA NTRS1990

Effect of wall cooling on the stability of compressible subsonic flows over smooth humps and backward-facing steps

Al-Maaitah, Ayman A.↗

NASA NTRS1979

Volcanic features of Io

The various volcanic landforms observed on Io by Voyager 1 are described and compared with similar features on earth. Ionian calderas, observed to cover 5% of the surface, are generally found to be of low relief, similar to certain terrestrial calderas. Flow patterns observed include dark, linear markings with lobate margins resembling terrestrial lava flows, bright lobate markings originating at calderas, and a bright flow feature surrounding the calderas. Positive relief features associated with volcanic structures include pancake-like constructions similar to low volcanic cones, sheet-like structures, rugged mountains, and a type of surface upheaval. Bright and dark diffuse markings have also been found. The implications of the high rates of volcanic activity and the apparent abundance of sulfur on Io for the type of volcanism observed are discussed, and it is concluded that while there are strong arguments for sulfur flows on the surface of Io, silicate volcanism of the type observed on earth may also occur.

Carr, M. H.↗

NASA NTRS1990

Liquid-Flow Controller With Trickle Preflow

Liquid-flow controller allows pressure in liquid to increase steeply with flow as flow starts, then provides more-gradual nearly linear rise of pressure with flow as flow and pressure increase beyond preset breakpoint. Controller alternative version of mechanism described in "Liquid-Flow Controller Responds To Pressure" (MFS-28329) and "Liquid-Flow Controller With Preset Break Pressure" (MFS-28330). Material cut out of cone at tip of pintle. Liquid always passes from shell, albeit at low rate. When pressure in shell great enough to force orifice away from pintle, liquid flows at greater rate.

Cox, George B., Jr.↗