SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thin-film, tandem-junction, amorphous silicon (a-Si) photovoltaic modules were constructed in which a part of the a-Si alloy cell material is used to form bypass protection diodes. This integral design circumvents the need for incorporating external, conventional diodes, thus simplifying the manufacturing process and reducing module weight.
Composite materials are widely used in various types of engineering structures. To a large extent, the properties of composite materials are dependent on the fabrication process. But even the composite materials manufactured by the same process may demonstrate differences in their elastic properties. For design purposes, one should be aware of the potential variations in load-carrying capacity and dynamic behavior of such structures that can arise due to the uncertainty in elastic moduli. A more realistic analysis of composite structures should be performed with the variations of the elastic moduli being taken into consideration at the same time. The present paper is a generalization of a study where the influence of uncertainty in elastic moduli on the axial buckling load was discussed. Here, we consider another case of buckling, shells under uniform external pressure. In addition, this paper deals with the variability of natural frequencies by use of convex modeling, which is apparently the first study of this kind in the literature. A numerical approach to the uncertainty problem is nonlinear programming, which we apply to solve the same problem to generate a set of comparable numerical data. The results from both methods show good agreement throughout. Thus, the effectiveness of the analytic convex modeling is clearly demonstrated. The bounds of he natural frequency and the buckling load provide the designer with a better view of the vibrational behavior and the actual load carrying capacities possessed by the composite structure.
Despite efforts in the search for alternative means of energy, combustion still remains the key source. Most propulsion systems primarily use combustion for their needed thrust. Associated with these propulsion systems are the high-velocity hot exhaust gases produced as the byproducts of combustion. These exhaust products often apply uneven high temperature and pressure over the surfaces of the appended structures exposed to them. If the applied pressure and temperature exceed the design criteria of the surfaces of these structures, they will not be able to protect the underlying structures, resulting in the failure of the vehicle mission. An understanding of the flow field associated with hot exhaust jets and the interactions of these jets with the structures in their path is critical not only from the design point of view but for the validation of the materials and manufacturing processes involved in constructing the materials from which the structures in the path of these jets are made. The hot exhaust gases often flow at supersonic speeds, and as a result, various incident and reflected shock features are present. These shock structures induce abrupt changes in the pressure and temperature distribution that need to be considered. In addition, the jet flow creates a gaseous plume that can easily be traced from large distances. To study the flow field associated with the supersonic gases induced by a rocket engine, its interaction with the surrounding surfaces, and its effects on the strength and durability of the materials exposed to it, NASA Glenn Research Center s Combustion Branch teamed with the Ceramics Branch to provide testing and analytical support. The experimental work included the full range of heat flux environments that the rocket engine can produce over a flat specimen. Chamber pressures were varied from 130 to 500 psia and oxidizer-to-fuel ratios (o/f) were varied from 1.3 to 7.5.
Lunar regolith will be used for a variety of purposes such as oxygen and propellant production and manufacture of various materials. The design and development of chemical conversion reactors for processing lunar regolith will require an understanding of the coupling among the chemical, mass and energy transport processes occurring at the length and time scales of the overall reactor with those occurring at the corresponding scales of the regolith particles. To this end, a coupled transport model is developed using, as an example, the reduction of ilmenite-containing regolith by a continuous flow of hydrogen in a flow-through reactor. The ilmenite conversion occurs on the surface and within the regolith particles. As the ilmenite reduction proceeds, the hydrogen in the reactor is consumed, and this, in turn, affects the conversion rate of the ilmenite in the particles. Several important quantities are identified as a result of the analysis. Reactor scale parameters include the void fraction (i.e., the fraction of the reactor volume not occupied by the regolith particles) and the residence time of hydrogen in the reactor. Particle scale quantities include the time for hydrogen to diffuse into the pores of the regolith particles and the chemical reaction time. The paper investigates the relationships between these quantities and their impact on the regolith conversion. Application of the model to various chemical reactor types, such as fluidized-bed, packed-bed, and rotary-bed configurations, are discussed.
Lunar regolith will be used for a variety of purposes such as oxygen and propellant production and manufacture of various materials. The design and development of chemical conversion reactors for processing lunar regolith will require an understanding of the coupling among the chemical, mass and energy transport processes occurring at the length and time scales of the overall reactor with those occurring at the corresponding scales of the regolith particles. To this end, a coupled transport model is developed using, as an example, the reduction of ilmenite-containing regolith by a continuous flow of hydrogen in a flow-through reactor. The ilmenite conversion occurs on the surface and within the regolith particles. As the ilmenite reduction proceeds, the hydrogen in the reactor is consumed, and this, in turn, affects the conversion rate of the ilmenite in the particles. Several important quantities are identified as a result of the analysis. Reactor scale parameters include the void fraction (i.e., the fraction of the reactor volume not occupied by the regolith particles) and the residence time of hydrogen in the reactor. Particle scale quantities include the time for hydrogen to diffuse into the pores of the regolith particles and the chemical reaction time. The paper investigates the relationships between these quantities and their impact on the regolith conversion. Application of the model to various chemical reactor types, such as fluidized-bed, packed-bed, and rotary-bed configurations, are discussed.
This paper presents the detailed design and optimization of a three-stage axial supercritical carbon dioxide (sCO2) compressor to support the advancement of sCO 2 power cycles, recognized for their efficiency and compactness in energy conversion. The three-stage design is a scaled model of the original nine-stage 100 MW design. The aerodynamic design and structural analysis were performed at the University of Cincinnati, and the results are presented. The first stage of the design has been meticulously manufactured and experimentally tested at University of Notre Dame Turbomachinery Laboratory. The design process starts with the preliminary design process, considering the required operating boundary conditions and geometrical constraints for full stage design. The design is then scaled down to 3-stage based on the power limitation. The definition for design parameters has been inspired from the EEE HPC design and tweaked to fit the sCO 2 operation. Axisymmetric analysis is performed next and the parametric geometry modeler -Tblade3 has been used to create 3D blade geometry from the results which can then be exported for the 3D CFD analysis and optimization. An efficiency of 89.85% is predicted for the final design at the design point.
Issued in 2001, Presidential Executive Order 13221 directed federal agencies to purchase products with low standby power, with the goal of 1) reducing energy consumption in federal facilities, and 2) drawing attention to the problem of high standby power consumption, with guidance provided by the Federal Energy Management Program (FEMP). At that time, standby power was newly recognized as an increasing building energy load. Since then, procurement of products with low standby power have been set in place in acquisition processes, and the purchasing power of the federal government continues to influence manufacturers’ design decisions related to standby power. In recent years, FEMP has shifted effort from direct manufacturer outreach for data collection, to integrating low standby requirement into broader acquisition programs including Energy Star and Electronic Product Environmental Assessment Tool (EPEAT). Another milestone has been the labeling of low standby products on the GSA Advantage website to simplify and enhance compliance. Looking forward into the program’s future, this question arises “How do we design programs over time to reflect market and technology changes, by adjusting programmatic requirements while maintaining effectiveness?” This paper discusses that question for the case of standby power, which transitioned from covering a single to multiple environmental attributes, both in the context of the program’s past and future.
Exploiting grain boundary engineering in the design of alloys for extreme environments provides a promising pathway for enhancing performance relative to coarse-grained counterparts. Due to its attractive properties as a plasma facing material for fusion devices, tungsten presents an opportunity to exploit this approach in addressing the significant materials challenges imposed by the fusion environment. Here, we employ a ternary alloy design approach for stabilizing W against recrystallization and grain growth while simultaneously enhancing its manufacturability through powder metallurgical processing. Mechanical alloying and grain refinement in W-10 at.% Ti-(10,20) at.% Cr alloys are accomplished through high-energy ball milling with transitions in the microstructure mapped as a function of milling time. We demonstrate the multi-modal nature of the resulting nanocrystalline grain structure and its stability up to 1300 °C with the coarser grain size population correlated to transitions in crystallographic texture that result from the preferred slip systems in BCC W. Field-assisted sintering is employed to consolidate the alloy powders into bulk samples, which, due to the deliberately designed compositional features, are shown to retain ultrafine grain structures despite the presence of minor carbides formed during sintering due to carbon impurities in the ball-milled powders.
Abstract The coating and drying of inks and slurries are important steps to manufacture a plethora of products. Drying processes, particularly, comprise energy‐intensive steps that affect product cost and quality. Prior work has highlighted failures of various multicomponent diffusivity models to conserve mass in dryer modeling and challenges in predicting process limits given variability in published values of key thermodynamic parameters. Herein, we develop a computational model and benchtop drying experiments to investigate these concerns for drying polymer‐laden coatings. Model predictions of process limits in a single‐zone drying oven demonstrate that published variability in Flory–Huggins parameter yields large variations in predicted operating temperatures above which blistering occurs. This indicates that caution should be exercised when choosing approaches to obtain or predict the Flory–Huggins parameter, and that both benchtop drying experiments and a set of additional experiments, such as sorption experiments, are needed to fully characterize and optimize a given drying process.
Advanced manufacturing techniques have enabled the production of materials with state-of-the-art properties. In many cases however, the development of physics-based models of these techniques lags behind their development in the lab. This means that material and process development proceeds largely via trial and error. This is sub-optimal since experiments are cost-, time-, and labor-intensive. In this work we propose a machine learning framework, differential property classification (DPC), which enables an experimenter to leverage machine learning's unparalleled pattern matching capability to pursue data-driven experimental design. DPC takes two possible experiment parameter sets and outputs a prediction of which will produce a material with a more desirable property specified by the operator. We demonstrate the success of DPC on AA7075 tube manufacturing process and mechanical property data using shear assisted processing and extrusion (ShAPE), an emerging solid phase processing technology. We show that by focusing on the experimenter's need to choose between multiple candidate experimental parameters, we can reframe the challenging regression task of predicting material properties from processing parameters, into a classification task on which machine learning models can achieve good performance.
Engineered non-stochastic cellular materials show promising characteristics on the laboratory scale,with nearly ideal specific stiffness and strength scaling at ultralight mass density. These propertiessuggest performance benefits in any application with combined stiffness and mass constraints, suchas air vehicles. We investigate here the application of re-configurable cellular composite materialsand structures to lighter than air vehicles. We describe the properties and applicability of these materials,provide an example analysis of governing loading conditions associated with airships, showan example optimization method for navigating the design space, and describe how recent advancesin cellular material manufacturing and reconfiguration enable system performance benefits includingnew concepts of operation. Lastly, we propose lighter than air vehicles that are assembled andmaintained in-flight, eliminating structural compromises associated with transitional flight modesand ground handling.Engineered non-stochastic cellular material properties suggest performance benefits in lighter than air vehicles due tostiffness and mass constraints that are intrinsic to the airship design problem. Recent advances in cellular materialmanufacturing and reconfiguration enable system performance benefits including new concepts of operation, such aslighter than air vehicles that are assembled and maintained in-flight, eliminating structural compromises associatedwith transitional flight modes and ground handling. Existing engineered cellular materials display properties allowinglarge large scale airships design as monocoque cellular solids. Inevitable improvements in cellular material propertiesand manufacturing will improve feasibility even further. Given the suggestion that the two most significant technologygaps exist across all current airship projects are manufacturing and assembly processes and ground handling [7],a strategy that encompasses construction and maintenance in flight could provide critical rephrasing of the systemdesign problem through these new concepts of operation. Refactoring of traditional manufacturing, operation, andservice process constraints could extend to other domains in aerospace systems and manufacturing in general.In future work, the complexity of the design task would benefit from a form of optimization in order to find themost suitable geometry for a chosen application. For example, the Sequential Least SQuares Programming (SLSQP)function from within the SciPy Minimize library is a multiobjective constrained optimization method that has beenapplied to fixed wing aircraft design. [17] In this situation it would allow for several objective functions such as drag,bending stiffness, buoyancy and cost of transport to be incorporated into a composite objective function.
Additive manufacturing (AM) is increasingly utilized in aerospace applications. However, post-processing is required for many applications, so intricate designs are limited. Plasma electrolytic oxidation (PEO) was investigated as a post-processing treatment on Ti-6-4 (or Ti-6Al-4V: Alpha-beta titanium alloy with a high specific strength and excellent corrosion resistance)additively manufactured specimens. The “Keronite Black” PEO treatment reduced the surface roughness (Ra) of test specimens by approximately 0.5 μm. This reduction in Ra compared to the as-printed sample was hypothesized to benefit corrosion and fatigue properties because increased Ra is known to negatively impact corrosion and fatigue characteristics. Up to a 101% improvement in the corrosion potential (Ɛcorr) was observed. Although fatigue characteristics varied by PEO parameters, there was no significant fatigue debit due to the PEO treatment. Additionally, no effect to adhesion characteristics was observed due to PEO treatment. It is recommended that additional studies investigate the ability of PEO treatments to improve the corrosion, fatigue, chemical compatibility, radiation hardening, particle shedding characteristics, and flammability/oxidizer compatibility of aerospace additively manufactured components.
Extreme temperatures, both hot and cold, are anticipated in many of NASA space exploration missions as well as in terrestrial applications. One can seldom find electronics that are capable of operation under both regimes. Even for operation under one (hot or cold) temperature extreme, some thermal controls need to be introduced to provide appropriate ambient temperatures so that spacecraft on-board or field on-site electronic systems work properly. The inclusion of these controls, which comprise of heating elements and radiators along with their associated structures, adds to the complexity in the design of the system, increases cost and weight, and affects overall reliability. Thus, it would be highly desirable and very beneficial to eliminate these thermal measures in order to simplify system's design, improve efficiency, reduce development and launch costs, and improve reliability. These requirements can only be met through the development of electronic parts that are designed for proper and efficient operation under extreme temperature conditions. Silicon-on-insulator (SOI) based devices are finding more use in harsh environments due to the benefits that their inherent design offers in terms of reduced leakage currents, less power consumption, faster switching speeds, good radiation tolerance, and extreme temperature operability. Little is known, however, about their performance at cryogenic temperatures and under wide thermal swings. The objective of this work was to evaluate the performance of a new commercial-off-the-shelf (COTS) SOI parts over an extended temperature range and to determine the effects of thermal cycling on their performance. The results will establish a baseline on the suitability of such devices for use in space exploration missions under extreme temperatures, and will aid mission planners and circuit designers in the proper selection of electronic parts and circuits. The electronic part investigated in this work comprised of a CHT-NMOS80 high temperature N-channel MOSFET (metal-oxide semiconductor field-effect transistor) device that was manufactured by CISSOID. This high voltage, medium-power transistor is fabricated using SOI processes and is designed for extreme wide temperature applications such as geothermal well logging, aerospace and avionics, and automotive industry. It has a high DC current capability and is specified for operation in the temperature range of -55 C to +225 C
Modular Integrated Stackable Layers (MISL) is a computer system designed for simple, fast, and cost effective flexible reconfiguration in space environments such as the ISS and Orion projects for various uses. Existing applications include wireless and wired communications, data acquisition and instrumentation, and camera systems, and potential applications include bus protocol converters and subsystem control. MISL is based on Texas Instruments (TI)' MSP430 16-bit ultra-low-power microcontroller device. The purpose of my project was to integrate the MISL system with a liquid crystal display (LCD) touchscreen. The LCD, manufactured by Crystalfontz and part number CFAF320240F-035T-TS, is a 320 by 240 RGB resistive color screen including an optional carrier board. The vast majority of the project was done with Altium Designer, a tool for printed circuit board (PCB) schematic capture, 3D design, and FPGA (Field Programmable Gate Array) development. The new PCB was to allow the LCD to directly stack to the rest of MISL. Research was done with datasheets for the TI microcontroller and touchscreen display in order to meet desired hardware specifications. Documentation on prior MISL projects was also utilized. The initial step was to create a schematic for the LCD, power bus, and data bus connections between components. A layout was then designed with the required physical dimensions, routed traces and vias, power and ground planes, layer stacks, and other specified design rules such as plane clearance and hole size. Multiple consultation sessions were held with Hester Yim, the technical discipline lead for the Command and Data Handling Branch, and Christy Herring, the lead PCB layout designer in the Electronic Design and Manufacturing Branch in order to ensure proper configuration. At the moment, the PCB is awaiting revision by the latter-mentioned branch. Afterwards, the board will begin to undergo the manufacturing and testing process. Throughout the internship at Johnson Space Center, I gained several technical and professional skills. I gained proficiency in Altium Designer and experience using subversion clients, as well as knowledge in PSpice with OrCAD and battery design for spaceflight from on-site. I also gained networking, organization, and communication skills throughout meetings with coworkers and other interns. This internship at Johnson Space Center has impacted my future aspirations by further inspiring me to follow a career path into space rated engineering technology and human spaceflight applications. After graduation, I plan to attend graduate Modular Integrated Stackable Layers (MISL) is a computer system designed for simple, fast, and cost effective flexible reconfiguration in space environments such as the ISS and Orion projects for various uses. Existing applications include wireless and wired communications, data acquisition and instrumentation, and camera systems, and potential applications include bus protocol converters and subsystem control. MISL is based on Texas Instruments’ MSP430 16 bit ultra-low power microcontroller device. The purpose of my project was to integrate the MISL system with a liquid crystal display touchscreen. The LCD, manufactured by Crystalfontz and part number CFAF320240F-035T-TS, is a 320x240 RGB resistive color screen including an optional carrier board.The vast majority of the project was done with Altium Designer, a tool for printed circuit board (PCB) schematic capture, 3D design, and FPGA development. The new PCB was to allow the LCD to directly stack to the rest of MISL. Research was done with datasheets for the TI microcontroller and touchscreen display in order to meet desired hardware specifications. Documentation on prior MISL projects was also utilized. The initial step was to create a schematic for the LCD, power bus, and data bus connections between components. A layout was then designed with the required physical dimensions, routed traces and vias, power and ground planes, layer stacks, and other specified design rules such as plane clearance and hole size. Multiple consultation sessions were held with Hester Yim, the technical discipline lead for the Command and Data Handling Branch, and Christy Herring, the lead PCB layout designer in the Electronic Design and Manufacturing Branch in order to ensure proper configuration. At themoment, the PCB is awaiting revision by the latter-mentioned branch. Afterwards, the board will begin to undergo the manufacturing and testing process.Throughout the internship at Johnson Space Center, I gained several technical and professional skills. I gained proficiency in Altium Designer and experience using subversion clients, as well as knowledge in PSpice with OrCAD and battery design for spaceflight from on-site. I also gained networking, organization, and communication skills throughout meetings with coworkers and other interns. This internship at Johnson Space Center has impacted my future aspirations by further inspiring me to follow a career path into space rated engineering technology and human spaceflight applications. After graduation, I plan to attend graduate school for a master's or doctorate degree in electrical or computer engineering.
Additive manufacturing currently facilitates new avenues for materials discovery that have not been fully explored. In this study we reveal how additive manufacturing can be leveraged to produce dispersion strengthened (DS), multi-principal element alloys (MPEA) without the use of traditional mechanical alloying or chemical reactions. This new processing technique employed resonant acoustic mixing to coat an equiatomic NiCoCr powder with nano-scale yttrium oxides. Then, through laser powder bed fusion (L-PBF), the coated powder was successfully consolidated into 99.9% dense parts. Microstructural analysis confirmed the successful incorporation and dispersion of nano-scale oxides throughout the build volume. Furthermore, high temperature mechanical testing of the DS alloys showed significant improvements in strength and ductility over the baseline NiCoCr. As a result, this recently discovered processing route opens a new alloy design and production path that is synergistic between additive manufacturing and dispersion strengthening, possibly enabling a new generation of high-performance alloys.
The carbonation kinetics of monolithic cementing composites are strongly affected by gas transport which is, in turn, influenced by microstructural resistances and the presence of liquid water within pore networks. The non-uniform gas flow distribution within the CO 2 mineralization reactor can impart mass transfer resistance in the monolith microstructure, which affects the uptake of CO 2 (“carbonation”) of the cementing composites. This paper demonstrates how the gas spatial distribution (velocity and flow rate; quantified by CFD analysis) and processing conditions (temperature, relative humidity, and flow rate; quantified by factorial design) affect drying and carbonation, and in turn, the engineering properties of a representative ‘monolithic’ carbonate-cemented concrete component (i.e., herein concrete masonry unit: CMUs, also known as concrete block). It is shown that the gas flow distribution affects drying front penetration and results in moisture and carbonation gradients within the monolith. Particularly, variations in drying kinetics caused by non-uniformity of the contacting gas velocity impose gradients in moisture saturation, which results in increasing microstructural resistance to CO 2 transport. The resultant non-uniform carbonate-mineral formation (i.e., carbonate cementation), if not controlled, can produce gradients in mechanical properties and may alter failure patterns upon loading. Finally, these insights inform the optimal design of gas flow distribution systems and processing conditions within CO 2 mineralization reactors for the manufacturing of low-CO 2 concrete components using CO 2 -dilute industrial flue gas streams.
The aerospace, construction/architecture, and transportation manufacturing industries rely heavily on the mass production of near-net shape metallic and composite extrusions. While the production of raw extrusions is a relatively fast process, adding functional features such as holes and slots require additional time, cost, and energy to produce. To compensate for the inherent flexibility of extrusions, conventional machining requires rigid purpose-built fixtures for operations such as trimming, drilling and thinning. This approach requires that the machine tools be as large or larger than the parts themselves. This results in the need for excess shop floor space, energy for auxiliary equipment and motion systems, and significant capital expenditure. Considerable engineering expense and time involved in the designing, building, and proving out of part-specific fixtures for holding the components in specific configurations while machining add to the overall manufacturing cost. The primary objective of the technical collaboration between Oak Ridge National Laboratory and Fairmount Technologies (FT) is to improve the XM-3, a fixtureless CNC milling machine designed by FT. The machine was developed to trim, drill, and thin extrusions without part specific fixturing to make the manufacturing process more efficient and flexible. Dynamic measurements of the existing structure were collected, and modeling efforts were made to evaluate optimal machining parameters for the current system. Areas of improvement to increase the system stiffness, manufacturability, and machining efficiency were evaluated and highlighted for the next generation design. The impact of this effort may enable agile manufacturing across the commercial and defense aerospace industries, and other industries where extrusions are utilized like in the construction, architecture, and transportation industries.
The aerospace, construction/architecture, and transportation manufacturing industries rely heavily on the mass production of near-net shape metallic and composite extrusions. While the production of raw extrusions is a relatively fast process, adding functional features such as holes and slots require additional time, cost, and energy to produce. To compensate for the inherent flexibility of extrusions, conventional machining requires rigid purpose-built fixtures for operations such as trimming, drilling and thinning. This approach requires that the machine tools be as large or larger than the parts themselves. This results in the need for excess shop floor space, energy for auxiliary equipment and motion systems, and significant capital expenditure. Considerable engineering expense and time involved in the designing, building, and proving out of part-specific fixtures for holding the components in specific configurations while machining add to the overall manufacturing cost. The primary objective of the technical collaboration between Oak Ridge National Laboratory and Fairmount Technologies (FT) is to improve the XM-3, a fixtureless CNC milling machine designed by FT. The machine was developed to trim, drill, and thin extrusions without part specific fixturing to make the manufacturing process more efficient and flexible. Dynamic measurements of the existing structure were collected, and modeling efforts were made to evaluate optimal machining parameters for the current system. Areas of improvement to increase the system stiffness, manufacturability, and machining efficiency were evaluated and highlighted for the next generation design. The impact of this effort may enable agile manufacturing across the commercial and defense aerospace industries, and other industries where extrusions are utilized like in the construction, architecture, and transportation industries.