Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Titanium Alloys Thin Sheet Welding with the Use of Concentrated Solar Energy

The present study deals with the welding of titanium alloys thin sheets 1.3 mm thick, with the use of concentrated solar energy. The experimental part of the work took place at a medium size solar furnace at the installation of the Centre National de la Recherche Scientifique, at Odeillo, in Southern France, where similar and dissimilar defect-free welds of titanium Grades 4 and 6 were achieved, in the butt joint configuration. After the determination of the appropriate welding conditions, the optimum welded structures were examined and characterized microstructurally, by means of light optical microscopy, scanning electron microscopy, and microhardness testing. In addition, test pieces extracted from the weldments were tested under uniaxial tensile loading aiming to the estimation of the strength and the ductility of the joint. The analysis of the experimental results and the recorded data led to the basic concluding remarks which demonstrate increased hardness distribution inside the fusion area and severe loss of ductility, but adequate yield and tensile strength of the welds.

36 MATERIALS SCIENCE↗

Effect of Overaging on Fatigue Crack Propagation and Stress Corrosion Cracking Behaviors of an Al-Zn-Mg-Cu Alloy Thick Plate

The fatigue property as well as stress corrosion cracking (SCC) resistance of an Al-Zn-Mg-Cu alloy thick plate in peak-aged and overaged tempers (T7351 and T7651) is systematically investigated by fatigue crack propagation (FCP) test and slow strain rate test (SSRT). Microstructural characterization is examined by transmission electron microscopy and scanning electron microscopy. Results reveal that the T7351 alloy has lower strength but higher electrical conductivity as compared to T7651 alloy. The FCP resistance of T7351 alloy is superior to that of the T7651 alloy due to the coarser precipitates in the highly overaged alloy in which the strain localization is reduced by promoting homogeneous slip. In addition, the SSRT test suggests a higher SCC resistance in T7351 alloy. The enhanced SCC resistance is found to depend on grain boundary precipitate characteristics and crack propagation resistance of the alloys.

36 MATERIALS SCIENCE↗

The Microstructure, and Mechanical and Corrosion Properties of As-Cast and As-Extruded Mg-2%Zn-x%Cu Alloys After Solution and Aging Heat Treatments

The effects of different Cu concentrations and heat treatment on the microstructure, mechanical and corrosion properties of the as-cast and hot-extruded Mg-2%Zn alloys were studied. The results showed that T6 heat treatment led to the dissolution of intermetallics and breaking the continuous networks of intermetallics. Also, the grain size of the base alloy decreased with further Cu additions after solution and aging heat treatments. Microstructural characterization indicated that Mg(Zn,Cu) and Mg(Zn,Cu){sub 2} intermetallics were formed which their volume fractions increased with exceeding Cu additions. Moreover, the addition of 3 wt.% Cu and T6 heat treatment increased the Brinell hardness of both as-cast and hot-extruded specimens reached to 94 HBN and 116 HBN, respectively. The optimum amounts of the ultimate tensile strength and elongation values obtained from 0.1 wt.% Cu addition for both conditions after T6 treatment which were 253 MPa, 11.5% and 263 MPa, 14.7%, respectively. However, more Cu addition (> 0.5 wt.%) deteriorated the tensile properties of the alloy due to the high volume fraction of intermetallics. The yield tensile strength increased continuously with different Cu additions for the cast and extruded alloys after solution and aging heat treatments. After T6 heat treatment, extruded alloys showed better anti-corrosion properties than those of the cast alloys, while the extruded Mg-2%Zn-0.1%Cu alloy exhibited the best anti-corrosion property. Further Cu addition increased the volume fraction of intermetallics and enhanced the corrosion rate which was due to the galvanic couple effect.

36 MATERIALS SCIENCE↗

Retained Austenite Attributes and Mechanical Performance of Different Compositions of TRIP Steel Alloys

The main objective of this work is to correlate the different attributes of retained austenite phase in TRIP steel structure with its mechanical properties. Three different chemical compositions were used to produce TRIP steel alloys. The first alloy contains only silicon as a carbide precipitation inhibitor; in the second alloy, silicon is partially replaced with aluminum, while in the third alloy phosphorus is added to the silicon–aluminum alloy. These compositions were proposed in order to avoid the negative effect of silicon during galvanizing. These three steel alloys were cast, homogenized, hot-forged and then subjected to intercritical annealing treatment followed by cooling and isothermal treatment in salt bath with subsequent air-cooling. Microstructural characterization, using optical microscope, SEM and XRD, along with tensile testing was carried out. Retained austenite attributes include volume fraction, carbon content, total carbon content, retained austenite transformable index and its stability coefficient against strain-induced martensite (SIM) transformation. The effect of these attributes on the mechanical properties of the studied TRIP steel alloys was evaluated using tensile test date, i.e., ultimate tensile strength (UTS), ductility, yield strength to UTS ratio, performance index and strain-hardening exponent. The variation of strain-hardening rate and strain-hardening exponent with strain was also considered. The failure behavior of the studied steel alloys was investigated using SEM on tensile-tested specimens. The results show that Si/Al-alloy has the lowest retained austenite transformable index, lowest stability coefficient against SIM transformation, highest performance index and more stable and uniform variation in strain-hardening rate and strain-hardening exponent with strain. These properties satisfy the industrial constrains of the sheets used in automotive industry relating to better mechanical properties and galvanizability.

36 MATERIALS SCIENCE↗

Effect of Tempering Mode on the Microstructure and Mechanical Properties of a Lean Alloy Martensitic Steel: Conventional Reheating Versus Induction Reheating

The present study elucidates the effect of the reheating rate and tempering temperature on the type, size, and distribution of carbides/cementite formed within martensite (M)/lower bainite (LB) during the tempering of a high-strength low-alloy (HSLA) steel. A comparison is made between conventional reheating and induction reheating. All the experimental samples were quenched from the austenitization temperature of 920 °C for 30 min. An ultra-high yield strength of 1180 MPa and a good toughness of 94 J at 0 °C were obtained after tempering at 400 °C for 15 min by induction reheating (~ 100 °C/s), while in the case of conventional reheating (~ 2 °C/s) and tempering at 400 °C for 15 min, the steel had a high strength of 1159 MPa, but a poor toughness of 47 J at 0 °C. After induction reheating to 500 °C and tempering for 15 min, a higher toughness was obtained (91 J at 0 °C), but the strength was decreased to 967 MPa. Microstructural characterization revealed that fine needle-like carbides (ε-Fe{sub 2.4}C) were obtained by induction reheating to 400 °C and tempering for 15 min. However, samples tempered at 400 °C by conventional reheating and 500 °C by induction reheating both precipitated coarse θ-Fe{sub 3}C. In the former, θ-Fe{sub 3}C precipitated at locations that were previously austenite grain boundaries and led to tempered martensite embrittlement (TME). In the latter, Ostwald ripening occurred, and the precipitates could not maintain high strength. The excellent mechanical properties of induction reheated steel (400 °C, 15 min) are attributed to the following aspects: (a) The selection of appropriate tempering temperature did not lead to decarburization and ensured high strength, and (b) a high reheating rate promoted carbide dispersion and avoided TME in steel.

36 MATERIALS SCIENCE↗

Influence of Torsion on Precipitation and Hardening Effects during Aging of an Extruded AZ91 Alloy

The effect of torsional deformation by various routes prior to artificial aging treatment on the microstructure of extruded AZ91 rods was investigated. The tension and compression properties along the extruded direction were tested to evaluate the hardening effect. The results showed that torsional deformation can largely enhance the subsequent age-hardening effect. A detailed microstructural characterization revealed that torsional deformation produced a high density of dislocations and {10-12} twins, which can promote continuous precipitation and increase the number density of the Mg{sub 17}Al{sub 12} phase. In addition, part of dislocations and the {10-12} twins were retained after aging treatment. The combination of the increased precipitation hardening by Mg{sub 17}Al{sub 12}, dislocation strengthening and refinement strengthening contributed to the high hardening effect. Moreover, the hardening effect can be further increased by tailoring the torsion route. The torsion route exhibited little influence on the age-hardening effect, while it remarkably affected the texture of the twisted AZ91 rods. Reciprocating torsion had little influence on the texture. In contrast, unidirectional torsion caused the c-axis of the texture to rotate toward the extrusion direction, resulting in a texture softening effect. Therefore, combining reciprocating torsion and aging caused a higher hardening effect than combining unidirectional torsion and aging. The detailed strengthening mechanism was analyzed and is discussed.

36 MATERIALS SCIENCE↗

Hot Deformation Behavior and Processing Map of a Fe-11Mn-10Al-0.9C Duplex Low-Density Steel Susceptible to κ-Carbides

The hot deformation behavior of a Fe-11Mn-10Al-0.9C duplex low-density steel has been investigated, based on a series of isothermal compression tests at temperatures of 800-1100 °C and strain rates of 0.001-10 s{sup −1}. At relatively lower temperatures, with austenite decomposing, continuous dynamic recrystallization of ferrite and the formation of inter-granular κ-carbide were responsible for significant softening. At high deformation temperature where austenite was a dominant phase, dynamic recrystallization (DRX) is the restoration mechanism. Processing maps were developed at different plastic strains employing dynamic materials model and further verified through microstructural characterization. The optimal hot deformation condition at a large strain (0.7) was identified as deformation temperature of 950-1100 °C and strain rate of 0.01-1.0 s{sup −1}. In this domain, the original coarse grains could be replaced by the fine and uniform recrystallized grains, indicating that the high efficiency was dissipated by DRX. Meanwhile, two instable regions resulted from the formation of inter-granular κ-carbides and necklace structure should be avoided during hot processing.

36 MATERIALS SCIENCE↗

Evaluating the Discharge Performance of Heat-Treated Al-Sb Alloys for Al-Air Batteries

In this work, the combined effects of heat treatment and Sb addition on the discharge performance of Al-Sb alloys as anode for Al-air batteries have been evaluated experimentally. The results indicate that heat treatment decreases the electrochemical and discharge activities of Al-Sb alloys. Heat-treated Al-Sb alloys at 550 °C for 3 h show an improved anode performance. The Al-0.02Sb alloy exhibits a high discharge capacity and anodic efficiency of 2758 Ah kg{sup −1} and 92.6%, respectively. Further prolonging the heat treatment time results in a decrease in anode performance. Microstructure characterization indicates that such negative effect is due to the higher-temperature and prolonged heat treatment to bring out significant grain growth and coarsening of Al-Sb precipitates. The corresponding corrosion behaviors are also discussed in detail.

36 MATERIALS SCIENCE↗

Effect of Tool Offset and Rotational Speed in Dissimilar Friction Stir Welding of AISI 304 Stainless Steel and Mild Steel

In the present study, dissimilar friction stir welding was carried out between stainless steel (UNS S30400) and mild steel (UNS G10080) plates of 4 mm thickness using a tungsten carbide tool. The influence of tool rotational speeds (600, 875 rpm) and tool offsets (0.6, 1.2 mm) on mechanical properties, i.e., hardness, tensile strength, and impact toughness of welded joints was investigated. Maximum tensile strength of the joint was about 107.6% of the mild steel under rotational speed of 875 rpm and tool offset of 1.2 mm. The maximum hardness reached in the stir zone was about 281 HV{sub 0.5} due to the phase transformations and grain refinement. Charpy’s notch toughness of the welded joints was observed lower than the base materials. The microstructural characterizations were carried by using an optical microscope, and FESEM–EDS analysis which revealed the complex material mixing and material movement during the welding. Tungsten-rich bands were observed in the weld micrograph especially toward the advancing side. During this study, various wear mechanisms like oxidation wear, abrasive wear, and adhesion wear were responsible for the degradation of tungsten carbide tool.

36 MATERIALS SCIENCE↗

Influence of Two Different Salt Mixture Combinations of Na{sub 2}SO{sub 4}-NaCl-NaVO{sub 3} on Hot Corrosion Behavior of Ni-Base Superalloy Nimonic263 at 800 °C

Isothermal hot corrosion behavior of Nimonic263 alloy was studied under the influence of two different salt mixtures of 87.5 wt.% Na{sub 2}SO{sub 4} + 5 wt.% NaCl + 7.5 wt.% NaVO{sub 3} (3SM) and 74 wt.% Na{sub 2}SO{sub 4} + 21.7 wt.% NaCl + 4.3 wt.% NaVO{sub 3} (3SM-A) and also without salt mixtures up to 500 h at 800 °C. Corrosion kinetics showed that 3SM-A is more aggressive than 3SM. Multiple oxides, spinels, sulfides, vanadate compounds, and volatile compounds were observed during various hot corrosion reactions. The volatile compounds NaClO{sub 3} and CrMoO{sub 3}, and SO{sub 3} gas are attributed to the weight loss under both 3SMs. The Na{sub 2}SO{sub 4} of 3SM prevailed till 400 h, but that of 3SM-A disappeared within 5 h, as established conclusively by Raman spectra analysis. The sulfides plus internal oxide zone increased with the increased exposure duration as evident from the extensive EPMA analysis. Based on the critical analysis of corrosion kinetics and detailed microstructural characterization, fluxing and sulfidation followed by oxidation are identified as plausible hot corrosion mechanisms under both 3SMs. Besides, chlorination and high-temperature oxidation mechanisms occur under 3SM-A condition.

36 MATERIALS SCIENCE↗

Development of Fe-9Cr Alloy via High-Energy Ball Milling and Spark Plasma Sintering

Iron and chromium powders were mixed and mechanically alloyed via high-energy ball milling for different time durations (2–20 h) to produce an alloy powder with a nominal composition of Fe-9Cr (wt.%). The milled Fe-9Cr powders were analyzed using scanning electron microscopy (SEM), x-ray diffraction (XRD) and transmission electron microscopy (TEM) to understand the impact of ball milling (BM) time on the characteristics of the milled powder. The optimized milled powder samples were then consolidated via spark plasma sintering (SPS) for different dwell times and temperatures. The density of consolidated samples was found to reach a maximum of 98%. Microstructural characterization of the SPS samples were performed using XRD, SEM, TEM and electron backscatter diffraction. This study highlights the principles and importance of high-energy BM and SPS of Fe-9Cr model alloy for the future development of more complex oxide dispersion-strengthened alloys for various applications including advanced nuclear reactor applications.

36 MATERIALS SCIENCE↗

Creep Behavior and Phase Equilibria in Model Precipitate Strengthened Alumina-Forming Austenitic Alloys

Abstract Creep-rupture behavior and microstructural response in alumina-forming austenitic (AFA) alloys with two different precipitation strengthening mechanisms, “Laves-phase + M 23 C 6 carbide” and “coherent L1 2 γ′-Ni 3 (Al,Ti),” were explored as “model” cases of multi-phase, multi-scale heat-resistant AFA alloys for 650–750°C use. These alloys will be used to guide and verify computational alloy design and life-prediction modeling under an on-going eXtremeMAT project through the Office of Fossil Energy and Carbon Management, US Department of Energy. Computational thermodynamics were used to design and predict the amounts of strengthening and deteriorating secondary phases at 750°C. Creep-rupture lives of the alloys tested at 750°C and 100 MPa were in a range of 4000–9000 h, and the microstructure at the gage/grip after creep-rupture testing was compared with isothermally aged alloys for 1500 h, as well as the calculated phases. Detailed microstructure characterization includes phase identification, volume fraction measurement, and compositional analysis, which were correlated with the creep-rupture properties. High-temperature oxidation resistance was also screened and compared with commercial, chromia-forming heat-resistant steels. These model alloys also provide the basis for further design and optimization of next generation AFA alloys with improved creep resistance.

36 MATERIALS SCIENCE↗

Novel self-assembled two-dimensional layered oxide structure incorporated with Au nanoinclusions towards multifunctionalities

Two-dimensional (2D) layered oxides have recently attracted wide attention owing to the strong coupling among charges, spins, lattice, and strain, which allows great flexibility and opportunities in structure designs as well as multifunctionality exploration. In parallel, plasmonic hybrid nanostructures exhibit exotic localized surface plasmon resonance (LSPR) providing a broad range of applications in nanophotonic devices and sensors. A hybrid material platform combining the unique multifunctional 2D layered oxides and plasmonic nanostructures brings optical tuning into the new level. Here, a novel self-assembled Bi 2 MoO 6 (BMO) 2D layered oxide incorporated with plasmonic Au nanoinclusions has been demonstrated via one-step pulsed laser deposition (PLD) technique. Comprehensive microstructural characterizations, including scanning transmission electron microscopy (STEM), differential phase contrast imaging (DPC), and STEM tomography, have demonstrated the high epitaxial quality and particle-in-matrix morphology of the BMO-Au nanocomposite film. DPC-STEM imaging clarifies the magnetic domain structures of BMO matrix. Three different BMO structures including layered supercell (LSC) and superlattices have been revealed which is attributed to the variable strain states throughout the BMO-Au film. Owing to the combination of plasmonic Au and layered structure of BMO, the nanocomposite film exhibits a typical LSPR in visible wavelength region and strong anisotropy in terms of its optical and ferromagnetic properties. This study opens a new avenue for developing novel 2D layered complex oxides incorporated with plasmonic metal or semiconductor phases showing great potential for applications in multifunctional nanoelectronics devices.

36 MATERIALS SCIENCE↗

Mass production of high-performance single atomic FeNC electrocatalysts via sequenced ultrasonic atomization and pyrolysis process

Mass production of highly efficient, durable, and inexpensive single atomic catalysts is currently the major challenge associated with the oxygen reduction reaction (ORR) for fuel cells. In this study, we develop a general strategy that uses a simple ultrasonic atomization coupling with pyrolysis and calcination process to synthesize single atomic FeNC catalysts (FeNC SACs) at large scale. The microstructure characterizations confirm that the active centers root in the single atomic Fe sites chelating to the four-fold pyridinic N atoms. The identified specific Fe active sites with the variable valence states facilitate the transfer of electrons, endowing the FeNC SACs with excellent electrochemical ORR activity. The FeNC SACs were used as cathode catalysts in a homemade Zn-air battery, giving an open-circuit voltage (OCV) of 1.43 V, which is substantially higher than that of commercial Pt/C catalysts. This study provides a simple approach to the synthesis of single atomic catalysts at large scale.

36 MATERIALS SCIENCE↗

High-entropy Al 0.3 CoCrFeNi alloy fibers with high tensile strength and ductility at ambient and cryogenic temperatures

High-entropy alloys (HEAs) are multi-component systems based on novel alloy composition designs with entropy maximization. They feature an array of unique mechanical properties when compared with traditional alloys. In this study, HEA fibers with diameters ranging from 1 to 3.15 mm in diameter, with the composition of Al 0.3 CoCrFeNi (atomic percent, at.%), were successfully fabricated by hot-drawing, followed by microstructural characterization using scanning-electron microscopy (SEM) and transmission-electron microscopy (TEM). The compositional variations within and between fibers were determined using energy-dispersive X-ray spectroscopy in TEM along with atomic-probe tomography (APT). These analyses revealed a homogeneous face-centered cubic (FCC) structure in the as-cast material, while post processing (e.g., forging and wire drawing) produced nanosized B2 particles in an FCC matrix. Electron back-scatter diffraction (EBSD) was used to determine the evolution of the texture and grain boundary character after processing of the fibers. The tensile strength and plasticity of the fibers were determined at both 298 K (1207 MPa/7.8%) and 77 K (1600 MPa/17.5%). Detailed TEM analyses revealed that the improvement of mechanical properties at 77 K (i.e. increased strength and ductility) is due to a change in deformation mechanisms from the planar slip of dislocations to nano-twinning. Such properties could be beneficial for cryogenic applications.

36 MATERIALS SCIENCE↗

Neutron irradiation-induced microstructure damage in ultra-high temperature ceramic TiC

Titanium carbide (TiC) is an ultra-high temperature ceramic with potential as a structural material candidate for advanced reactor concepts. However, the irradiation tolerance of TiC is not well understood. Here, we reveal the key irradiation damage microstructure degradation processes in TiC using mixed spectrum neutron irradiations at dose of ~2 displacements per atom (dpa) at temperatures of ~220, 620, and 1115 °C, combined with state-of-art microstructure characterization using transmission electron microscopy (TEM) and high-resolution TEM (HRTEM). The helium injection (~65 atomic parts per million) produced by neutron transmutation also occurred in the sample. TiC was observed to form irradiation-induced interstitial-type dislocation loops and He-stabilized cavities. At 220 and 620 °C, the analysis of the electron diffraction patterns, rel-rod imaging and HRTEM revealed that the dislocation loops were faulted Frank loops with Burgers vector b Frank = 1/3<111> lying on {111} planes. A detailed Burgers vector identification performed by the g.b technique revealed that the dislocation loops forming at 1115 °C were unfaulted, edge-type, with Burgers vectors b = a<100> and a/2<110> with corresponding {100} and {110} habit planes. Using continuum mechanics, we estimated the critical radius at which a faulted dislocation loop transitions to a perfect loop to be 9 nm. Further, no amorphization occurred in TiC under-investigated irradiation conditions while macroscopic swelling under point defect swelling regime was observed. He-stabilized cavities were detected at 1115 °C, but not at lower temperature irradiation. These observations indicate the onset of long-range vacancy migration in TiC occurs between 620 and 1115 °C.

36 MATERIALS SCIENCE↗

Crystallographic orientation and spatially resolved damage in a dispersion-hardened Al alloy

The in-situ neutron diffraction technique, in combination with both the full-field crystal elasto-viscoplastic finite element model and microstructural characterization, was used to study the deformation-induced damage anisotropy in a commercial Al alloy, subjected to uniaxial tensile and cyclic loading. The simulations capture well the crystallographic-orientation-dependent lattice strain behavior. The hard grains, e.g. those orientated with the <111> and <422> orientations parallel with the uniaxial loading direction (LD), feature large Taylor factors and seem more prone to form damage-related band structures. Their effective elastic moduli decrease with the accumulation of damage, which are different from the soft grains orientated with the <200> orientation along the LD. Correlation between the distribution of voids and that of the residual lattice strain developed after failure may exist. The maximum tensile type residual lattice strain observed after failure may be resulted from the band structure formed in the hardest <111> grains. It was revealed that the band structure triggered by the hard particles could be one of sources of damage. In addition, while the specimen was obviously damaged, a fast stress relief was evidenced after unloading from the tension, especially at the beginning of unloading. Our present investigations provide a novel method for exploring the damage mechanisms of polycrystalline materials during plastic deformation.

36 MATERIALS SCIENCE↗

Microstructure, fatigue, and impact toughness properties of additively manufactured nickel alloy 718

A complete understanding of processing-structure-property-performance relationship of additively manufactured (AM) components are critical from an application standpoint. Therefore, in the current investigation, a comprehensive microstructural characterization and mechanical properties (tensile, fatigue and impact toughness) evaluation of nickel alloy 718 AM by the laser powder bed fusion (L-PBF) technique have been performed. AM builds were made from powders manufactured via different atomization conditions. Although the standard post-heat treatment procedure led to the removal of severe interdendritic segregation both grain boundary and intra-grain precipitation of d phase occurred. Regardless of d phase presence, axial fatigue properties of both the AM builds were similar to design handbook wrought fatigue data. However, due to the d phase, impact toughness properties were comparable to the wrought material conditions that exhibited d phase. Fractured surfaces of Charpy impact samples exhibited crack propagation extensively along the boundaries decorated by d precipitates.

Komarasamy, Mageshwari↗