Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Lanthanide migration and immobilization in metallic fuels

It is recognized that the lanthanide fission products can enhance the fuel-cladding chemical interaction (FCCI), which is a key concern of using metallic fuels such as U-Zr in a sodium-cooled fast reactor. The present work conducts a critical review on the analysis of lanthanide functions in FCCIs. Available in-pile and out-of-pile data are first collected and analyzed, then the theories for lanthanide migration and redistribution in the fuel in operation are analyzed. For mitigating FCCIs, one of the effective method is applying fuel additives for immobilizing lanthanides. The review investigates four candidates of fuel additives (Pd, Sn, Sb and In), and it is concluded that Sb can be the best candidate among the four elements based on current available thermodynamic data and microstructure characterizations. Considering that FCCIs lead to formation of metallic alloys/compounds between lanthanides and steel cladding constituents (Fe, Cr, and Ni), the review also analyzes the thermodynamic data such as enthalpy of formation of the alloys and/or metallic compounds and identify the solidus temperature of each alloy.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Influence of hot isostatic pressing on the performance of aluminum alloy fabricated by ultrasonic additive manufacturing

Ultrasonic additive manufacturing (UAM) is a solid-state manufacturing technique employing principles of ultrasonic welding coupled with mechanized tape layering to fabricate fully functional parts. However, UAM-fabricated parts often exhibit a reduction in strength when loaded normal to the welding interfaces (Z-direction). Here, the effect of hot isostatic pressing (HIP) on UAM builds of aluminum alloy was explored. Tensile testing and microstructure characterization were conducted; it was established that HIP eliminated the brittle Z-direction fracture and improved the strength and ductility of the Z-direction specimens. HIP eliminated voids and produced recrystallized structure; however, welding interfaces survived the HIP treatment.

36 MATERIALS SCIENCE↗

A new magnesium sheet alloy and its multi-stage homogenization for simultaneously improved ductility and strength at room temperature

We report that a new Mg-2Zn-0.3Ca-0.2Ce-0.1Mn (ZXEM2000) alloy and a multi-stage homogenization process have been designed and developed based on CALculation of Phase Diagram (CALPHAD) modeling results and experimental validation. The new sheet alloy offers an excellent combination of ductility (about 29% elongation) and yield strength (157 MPa), promising room-temperature forming applications. Microstructure characterization reveals that the exceptional properties of this alloy are mainly attributed to the weak basal texture, fine average grain size and high density of nano-scale Mn and Mg 6 Zn 3 Ca 2 precipitates achieved through multi-stage heat treatment and thermomechanical processing.

36 MATERIALS SCIENCE↗

Thermal Stability and Mechanical Properties of Cold-Sprayed Nickel-Yttria Coating

The microstructural evolution under the extreme environments imposed during cold spray deposition of cermet coatings and the microstructural recovery during post-processing annealing treatments is rather complex and not well understood. Here, Ni-Yttria cermet coatings on an SS304 substrate were produced using cold spray technique, resulting in a bimodal grain structure. The grain growth, phase stability, hardness, and wear properties are observed in as-deposited and annealed (at 400 °C) Ni-Yttria and pure Ni coatings. A multimodal microstructural characterization using electron microscopy, and atom probe tomography shows the structural and compositional stability of yttria particles and Ni grains. A fragmentation of Y-rich particles and dispersion in Ni was observed, however, no forced mixing/dissolution of Y in Ni is detected. Nano-yttria dispersed within the Ni grains slowed the grain growth during annealing. After annealing, Yttria reinforced coating was 1.5 times harder and showed better thermal and mechanical stability compared to the Ni coating.

Gwalani, Bharat↗

Helium partitioning to the core-shelled Ta nanoclusters in nanocrystalline Cu-Ta alloy

In this work, a nanocrystalline (NC) Cu-10at.%Ta alloy is irradiated with helium at different temperatures to assess the stability and effectiveness of Ta nanoclusters in trapping helium and suppressing swelling. Advanced microstructural characterization of the room-temperature irradiated specimens indicated the presence of small He-bubbles (∼1-2 nm) at the peak damage depth mainly at the core and along the interface of Ta nanoclusters with Cu matrix. Few bubbles were found along grain boundaries, with much smaller bubbles homogenously distributed within the copper lattice. High-temperature irradiation exhibited bubbles of ∼3-5 nm, which were primarily associated with nanoclusters as compared to other locations, with no observed faceting of the bubbles. In conclusion, atom probe analysis confirmed helium partitioning to the Ta nanoclusters indicating the effective entrapment of these He atoms.

36 MATERIALS SCIENCE↗

Tribological behavior of spark plasma sintered Ti 3 SiC 2 MAX phase composites

Ti₃SiC₂ MAX phases are considered promising candidates for tribological applications; but, their low hardness (5-6 GPa) can lead to increased abrasive wear and higher wear rates. This study investigates the effect of incorporating hard SiC particles on microstructure, mechanical, and tribological behavior of Ti₃SiC₂-SiC-based MAX phase composites prepared using spark plasma sintering at 1400 °C, 40 MPa, 15-minute holding time. Phase and microstructural characterization of composites confirmed the formation of Ti₃SiC₂ MAX phase (90%) along with TiC as a minor phase (10%). For Ti₃SiC₂-SiC, homogeneous distribution of SiC grains within Ti₃SiC₂ matrix resulted in increased hardness from ~11.6 GPa to ~14.8 GPa; however, the flexural strength decreased from ~615 MPa to ~597 MPa due to coefficient of thermal expansion mismatch. Tribological behavior of Ti₃SiC₂-SiC MAX phase composites was assessed using unidirectional sliding ball-on-flat tests with a 52100 steel ball at different loads and a constant speed of 0.05 m/s. SiC reinforced composites exhibited a decreased friction coefficient from 0.39 to 0.29 and wear rates comparable to Ti₃SiC₂ (7-10×10⁻³ mm³/N·m). SEM and EDS analysis of the worn surfaces indicated material transfer from the steel ball counter body and its oxidation due to frictional heating, at lower loads (2N and 5N), whereas at higher load (10N), fracture of the transfer layer dominated, with the presence of microcracks, delamination, grain pull-outs, and wear debris. Improved mechanical properties and good adhesion of SiC with Ti₃SiC₂ matrix resulted in reduced microcracks and grain pull-outs, making Ti₃SiC₂-SiC/Steel tribo-pair more suitable for tribological applications.

36 MATERIALS SCIENCE↗

Reduced Dislocation Introduction in III–V/Si Heterostructures with Glide-Enhancing Compressively Strained Superlattices

The novel use of a GaAs y P 1-y /GaP compressively-strained superlattice (CSS) to provide enhanced control over misfit dislocation (MD) evolution and threading dislocation density (TDD) during GaP/Si metamorphic heteroepitaxy is demonstrated. Here, the insertion of the CSS just after critical thickness, and thus prior to substantial dislocation introduction, is found to yield significantly reduced TDD in relaxed, 500 nm thick, n-type GaP/Si versus comparable control samples. The impact of CSS period count on average TDD and the overall dislocation network morphology was examined, supported by quantitative microstructural characterization, revealing a nearly 20× relative TDD reduction (to 2.4 ± 0.4×10 6 cm -2 ) with a 3-period CSS structure. A similarly low TDD (3.0 ± 0.6×10 6 cm -2 ) is maintained when the resultant n-GaP/Si virtual substrate is used for the growth of a subsequent n-type GaAs 0.75 P 0.25 -terminal GaAs y P 1-y step-graded metamorphic buffer. Although the physical mechanism for TDD reduction provided by these structures is not yet entirely understood, this initial work suggests that enhanced glide dynamics of MDs at or within the CSS placed early in the growth leads to a reduction in the total number of dislocations introduced overall, as opposed to annihilation-based reduction that occurs in conventional strained-layer superlattice dislocation filter approaches.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of the CO 2 Chemisorption in Li 5 FeO 4 , a New High Temperature CO 2 Captor Material. Effect of the CO 2 and O 2 Partial Pressures

Pentalithium ferrite (Li 5 FeO 4 ) was tested in this paper as possible CO 2 captor, both by theoretical calculations and experimental measurements. The pristine Li 5 FeO 4 compound with orthorhombic structure was synthesized via solid-state reaction and it was structural and microstructurally characterized. Later, sample was heat-treated at temperatures from room temperature to 900 °C under different CO 2 or CO 2 –O 2 atmospheres. Li 5 FeO 4 exhibits excellent CO 2 chemisorption abilities with a capture capacity about 12.9 mmol/g, which is outstanding in comparison to other previously reported ceramic captors. This material is able to react with CO 2 from 200 °C to approximately 715 °C showing a high kinetic of reaction even at CO 2 partial pressure values as low as 0.2. Finally and additionally, results suggest that oxygen addition does enhance the CO 2 chemisorption on Li 5 FeO 4 at temperatures below 700 °C, although oxygen addition seems to favor the desorption process at higher temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Self-Assembled BaTiO 3 –Au x Ag 1– x Low-Loss Hybrid Plasmonic Metamaterials with an Ordered “Nano-Domino-like” Microstructure

Metallic plasmonic hybrid nanostructures have attracted enormous research interest due to the combined physical properties coming from different material components and the broad range of applications in nanophotonic and electronic devices. However, the high loss and narrow range of property tunability of the metallic hybrid materials have limited their practical applications. In this study, a metallic alloy-based self-assembled plasmonic hybrid nanostructure, i.e., a BaTiO 3 –Au x Ag 1– x (BTO) vertically aligned nanocomposite, has been integrated by a templated growth method for low-loss plasmonic systems. Comprehensive microstructural characterizations including high-resolution scanning transmission electron microscopy (HRSTEM), energy-dispersive X-ray spectroscopy (EDS), and three-dimensional (3D) electron tomography demonstrate the formation of an ordered “nano-domino-like” morphology with Au 0.4 Ag 0.6 nanopillars as cylindrical cores and BTO as square shells. By comparing with the BTO–Au hybrid thin film, the BTO–Au 0.4 Ag 0.6 alloyed film exhibits much broader plasmon resonance, hyperbolic dispersion, low-loss, and thermally robust features in the UV–vis–NIR wavelength region. This study provides a feasible platform for a complex alloyed plasmonic hybrid material design with low-loss and highly tunable optical properties toward all-optical integrated devices.

36 MATERIALS SCIENCE↗

Exceptional NH 3 Detection by Cu(cyhdc) MOF Sensor Due to H 2 O Coadsorption

Metal–organic framework (MOF)-based electrical impedance sensors are a growing class of sensors that show utility in the detection of environmentally toxic gases. Detection of trace NH 3 has been particularly difficult to design due to the low electrical response of NH 3 . However, this has been circumvented by judiciously selecting a MOF that has enhanced electrical response to NH 3 due to coadsorption with predominant atmospheric gases such as water. Herein, an MOF Cu(cyhdc) based sensor has been successfully demonstrated for the enhanced detection of environmentally toxic NH 3 gas. The sensor shows a change in impedance when it is exposed to 5 ppm of NH 3 . At 20 °C, >30% relative humidity (RH) is necessary to elicit a change, with the response increasing with RH and reaching 3170× at 92% RH, producing the largest published response to NH 3 for a MOF direct electrical sensor. In the absence of water, no change is observed toward 5 ppm of NH 3 over 20–50 °C. Here, this electrical response is largely driven by huge decreases in the imaginary component of the impedance, attributed to increased capacitance at the surface of the MOF crystallites upon NH 3 and H 2 O coadsorption. Complementary structural and microstructural characterization proves that the Cu(cyhdc) crystalline structure and morphology remain intact under trace NH 3 and/or H 2 O adsorption. Despite extremely low NH 3 , loadings seen in TGA, XPS, and FT-IR confirm NH 3 and H 2 O adsorption, and changes to the metal-carboxylate IR peak positions are observed upon NH 3 adsorption. Concentrated primarily at the outer surfaces of the MOF crystallites, this NH 3 and H 2 O coadsorption effectively increases the surface capacitance across the Cu(cyhdc) powder and enables direct electrical detection of trace NH 3 . Together, these results demonstrate how coadsorption of specific molecules (H 2 O) can be used to enable the electrical detection of trace toxic gases that would otherwise not have produced a MOF sensor response.

ammonia↗

Stochasticity at Scales Leads to Lithium Intercalation Cascade

Porous intercalation electrodes are synonymous with the promise of lithium-ion batteries toward electromobility. These electrodes exhibit stochastic geometrical features spanning different length scales. The implication of microstructural inhomogeneity on the lithium intercalation dynamics is hitherto unknown. In this work, starting from three-dimensional (3D), X-ray tomograms of intercalation electrode microstructures, we characterize the microstructural variability in porous intercalation electrodes. Furthermore, a physics-based analysis of electrochemical response reveals that the stochastic features can cause preferential lithiation fronts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Switchable Chiral Selection of Aspartic Acids by Dynamic States of Brushite

Here, we show the chiral recognition and separation of aspartic acid (Asp) enantiomers by achiral brushite due to the asymmetries of their dynamical steps in its nonequilibrium states. Growing brushite has a higher adsorption affinity to d-Asp, while l-Asp is predominant on the dissolving brushite surface. Microstructural characterization reveals that chiral selection is mainly attributed to brushite [101] steps, which exhibit two different configurations during crystal growth and dissolution, respectively, with each preferring a distinct enantiomer due to this asymmetry. Because these transition step configurations have different stabilities, they subsequently result in asymmetric adsorption. Furthermore, by varying free energy barriers through solution thermodynamic driving force (i.e., supersaturation), the dominant nonequilibrium intermediate states can be switched and chiral selection regulated. This finding highlights that the dynamic steps can be vital for chiral selection, which may provide a potential pathway for chirality generation through the dynamic nature.

36 MATERIALS SCIENCE↗

Entropy and crystal-facet modulation of P2-type layered cathodes for long-lasting sodium-based batteries

Abstract P2-type sodium manganese-rich layered oxides are promising cathode candidates for sodium-based batteries because of their appealing cost-effective and capacity features. However, the structural distortion and cationic rearrangement induced by irreversible phase transition and anionic redox reaction at high cell voltage (i.e., >4.0 V) cause sluggish Na-ion kinetics and severe capacity decay. To circumvent these issues, here, we report a strategy to develop P2-type layered cathodes via configurational entropy and ion-diffusion structural tuning. In situ synchrotron X-ray diffraction combined with electrochemical kinetic tests and microstructural characterizations reveal that the entropy-tuned Na 0.62 Mn 0.67 Ni 0.23 Cu 0.05 Mg 0.07 Ti 0.01 O 2 (CuMgTi-571) cathode possesses more {010} active facet, improved structural and thermal stability and faster anionic redox kinetics compared to Na 0.62 Mn 0.67 Ni 0.37 O 2 . When tested in combination with a Na metal anode and a non-aqueous NaClO 4 -based electrolyte solution in coin cell configuration, the CuMgTi-571-based positive electrode enables an 87% capacity retention after 500 cycles at 120 mA g −1 and about 75% capacity retention after 2000 cycles at 1.2 A g −1 .

25 ENERGY STORAGE↗

Evolution of dislocations during the rapid solidification in additive manufacturing

Materials processed by fusion-based additive manufacturing (AM) typically exhibit relatively high dislocation densities, along with cellular structures and elemental segregation. This representative structural feature significantly influences material performance; however, post-mortem microstructure characterizations of AM materials cannot capture the dynamic evolution of dislocations during the manufacturing process, thereby offering limited mechanism-based guidance for further advancing AM techniques and facilitating the qualification and certification of AM products. In this study, we conduct operando high-energy synchrotron X-ray diffraction experiments on wire-laser directed energy deposition of 316 L stainless steel. Through a unique configuration, our operando synchrotron experiments semi-quantitatively probe the dislocation density in solid phases and their dynamic changes during solidification and subsequent cooling. By integrating this advanced synchrotron technique with multi-physics simulation, in-situ neutron diffraction, and multi-scale electron microscopy characterization, our mechanistic study aims to elucidate the effects of rapid cooling and subsequent thermal cycling on the dislocation generation and evolution.

36 MATERIALS SCIENCE↗

Impact of nitrogen on lithium-induced corrosion and cracking of RAFM steel

The emergence of private fusion enterprises, combined with advancements in U.S. and EU ITER-TBM as well as EU DEMO liquid breeder blanket concepts, has renewed focus on the materials challenges. This study examines the compatibility of reduced activation ferritic/martensitic (RAFM) steel in liquid Lithium (Li) containing various Nitrogen (N) concentrations, tested at 600 and 700 °C for 500 and 1000 h under static conditions. Microstructural characterization revealed the corrosion-induced dissolution and precipitation in Li containing 0.082 and 0.17 wt.% N at 600 °C, while limited dissolution and precipitation were observed in N-gettered Li using zirconium (Zr) and titanium (Ti) foils at 600 °C. Tensile testing at room temperature after Li exposure revealed a decrease in strength and ductility of the RAFM steel as a function of N content in Li. Severe embrittlement was observed after 500 h in Li containing 0.17 wt.% N at 600 °C and after 500 h in hot-gettered Li at 700 °C. Chromium (Cr) depletion from the steel matrix was observed, leading to the formation of M6C-type carbides on the surface identified by electron microscopy (SEM), X-ray diffraction (XRD), in agreement with thermodynamic calculations. These findings highlight the critical materials challenges posed by liquid Li breeder blanket concepts, emphasizing the need for improved strategies to address Li-induced dissolution, precipitation, and steel embrittlement due to N contamination of the coolant.

Romedenne, Marie [ORNL] (ORCID:0000000317936561)↗

Investigations towards incorporation of Eu 3+ and Cm 3+ during ZrO 2 crystallization in aqueous solution

Nuclear energy provides a widely applied carbon-reduced energy source. Following operation, the spent nuclear fuel (SNF), containing a mixture of radiotoxic elements such as transuranics, needs to be safely disposed of. Safe storage of SNF in a deep geological repository (DGR) relies on multiple engineered and natural retention barriers to prevent environmental contamination. In this context, zirconia (ZrO 2 ) formed on the SNF rod cladding, could be employed as an engineered barrier for immobilization of radionuclides via structural incorporation. This study investigates the incorporation of Eu 3+ and Cm 3+ , representatives for trivalent transuranics, into zirconia by co-precipitation and crystallization in aqueous solution at 80 °C. Complementary structural and microstructural characterization has been carried out by powder X-ray diffraction (PXRD), spectrum imaging analysis based on energy-dispersive X-ray spectroscopy in scanning transmission electron microscopy mode (STEM-EDXS), and luminescence spectroscopy. The results reveal the association of the dopants with the zirconia particles and elucidate the presence of distinct bulk and superficially incorporated species. Hydrothermal aging for up to 460 days in alkaline media points to great stability of these incorporated species after initial crystallization, with no indication of phase segregation or release of Eu 3+ and Cm 3+ over time. These results suggest that zirconia would be a suitable technical retention barrier for mobilized trivalent actinides in a DGR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quantitative assessment of Ni + and He + ion irradiation damage in a tungsten heavy alloy under the simulated nuclear fusion environment

A 90W-7Ni-3Fe (wt.%) tungsten heavy alloy has been sequentially Ni + and He + ion irradiated at 700 °C to simulate the high temperature irradiation environment of a fusion reactor interior. W/Ni–Fe-W dual-phase alloys have been proposed to serve as plasma facing materials and require detailed investigation of their behavior under fusion relevant conditions to assess their overall applicability. To evaluate material performance under five years of simulated fusion reactor service, microstructural characterization of the nanoscale defect distribution has been performed on both constituent phases, revealing peak swelling in the W phase of approximately 0.03%. The γ-phase (Ni–Fe-W) is found to swell approximately 0.68% under the same irradiation conditions, indicating significant cavity formation and growth. Additionally, a novel multi-projection imaging approach has been applied to determine the extent of damage segregation along the dual-phase W-to-γ interface and exposes that these interfaces act as sink sites for the accumulation of cavities. Interphase boundaries are noted to possess an 11.8% areal coverage of defects along the boundary plane, primarily on the γ-phase side of the boundary. The accumulation of cavities at these interphase boundaries is anticipated to adversely affect overall material toughness, and this work reveals a pressing need for mechanical property testing of irradiated W–Ni-Fe dual-phase alloys.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-throughput synthesis of high-entropy alloys via parallelized electric field assisted sintering

Materials discovery and design is an expensive and time-consuming process, though necessary to advance many engineering fields. In this work, a novel tooling design is utilized in conjunction with electric field assisted sintering (EFAS) to effectively create a new high-throughput synthesis technique: parallelized EFAS. Through this technique, a wide range of material compositions and geometries can be synthesized in parallel as isolated samples or as part of contiguous arrays. Multiple tooling designs are explored to examine both the flexibility and limitations of the technique. A series of increasing complex alloys is produced simultaneously using in situ alloying, beginning with pure Ni and adding equimolar constituents up to the septenary high-entropy alloy AlCoCrCuFeMnNi. Microstructural characterization reveals each sample is effectively fully dense and chemically homogenous while exhibiting phases in agreement with CALPHAD predictions. Scalability of parallelized EFAS is then experimentally demonstrated and the implications for materials discovery and automation are discussed.

36 - MATERIALS SCIENCE↗