Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Nonlinear steady-state response of a rotor-support system

A numerical method is presented to determine the steady-state nonlinear response of a rotor-support system due to deadband and rubbing using discrete Fourier transformation and inverse discrete Fourier transformation. Damaging subharmonic and superharmonic responses are found to occur in presence of a side force. The calculated results agree with the general trends which have been observed experimentally by other investigators. The effects of selected nondimensionalized parameters on rotor response are studied.

Noah, Sherif T.↗

On-line identification and attitude control for SCOLE

This paper documents on-line linear least-square identification and attitude control of SCOLE, a laboratory apparatus representing an offset-feed antenna attached to the Space Shuttle. Identification is done autonomously by starting a slew maneuver in pitch or roll with reaction jets and observing the time history data of associated Euler angles when the jets are quiescent. Linear least-square analysis is used to select the parameters that best fit the output of an Autoregressive (AR) model to the data. The control effectiveness of the jets is determined in a subsequent test, again using linear least squares. The parameters so derived are used to design switching lines for time-optimal attitude control. This report describes the identification and control algorithms and the experimental apparatus and procedures used. Also, experimental data are presented that reflect the performance of the identification algorithms and the attitude control system.

Montgomery, R. C.↗

Simultaneous structural and control optimization via linear quadratic regulator eigenstructure assignment

A method for simultaneous structural and control design of large flexible space structures (LFSS) to reduce vibration generated by disturbances is presented. Desired natural frequencies and damping ratios for the closed loop system are achieved by using a combination of linear quadratic regulator (LQR) synthesis and numerical optimization techniques. The state and control weighing matrices (Q and R) are expressed in terms of structural parameters such as mass and stiffness. The design parameters are selected by numerical optimization so as to minimize the weight of the structure and to achieve the desired closed-loop eigenvalues. An illustrative example of the design of a two bar truss is presented.

Becus, G. A.↗

Analytical investigation of the dynamics of tethered constellations in earth orbit

This Quarterly Report on Tethering in Earth Orbit deals with three topics: (1) Investigation of the propagation of longitudinal and transverse waves along the upper tether. Specifically, the upper tether is modeled as three massive platforms connected by two perfectly elastic continua (tether segments). The tether attachment point to the station is assumed to vibrate both longitudinally and transversely at a given frequency. Longitudinal and transverse waves propagate along the tethers affecting the acceleration levels at the elevator and at the upper platform. The displacement and acceleration frequency-response functions at the elevator and at the upper platform are computed for both longitudinal and transverse waves. An analysis to optimize the damping time of the longitudinal dampers is also carried out in order to select optimal parameters. The analytical evaluation of the performance of tuned vs. detuned longitudinal dampers is also part of this analysis. (2) The use of the Shuttle primary Reaction Control System (RCS) thrusters for blowing away a recoiling broken tether is discussed. A microcomputer system was set up to support this operation. (3) Most of the effort in the tether plasma physics study was devoted to software development. A particle simulation code has been integrated into the Macintosh II computer system and will be utilized for studying the physics of hollow cathodes.

Lorenzini, Enrico C.↗

Parametric studies of electric propulsion systems for orbit transfer vehicles

The present parametric tradeoff study for OTV electric propulsion systems encompasses ammonia and hydrogen arcjets as well as Xe-ion propulsion systems with performance characteristics currently being projected for 1993 operation. In all cases, the power source is a nuclear-electric system with 30 kg/kW(e) specific mass, and the mission involves the movement of payloads from lower orbits to GEO. Attention is given to payload capabilities and associated propellant requirements. Mission trip time is identified as the key parameter for selection; while arcjets are preferable for shorter trip times, ion propulsion is more advantageous for longer trip times due to reduced propellant mass fraction.

Manvi, R.↗

A methodology for the assessment of manned flight simulator fidelity

A relatively simple analytical methodology for assessing the fidelity of manned flight simulators for specific vehicles and tasks is offered. The methodology is based upon an application of a structural model of the human pilot, including motion cue effects. In particular, predicted pilot/vehicle dynamic characteristics are obtained with and without simulator limitations. A procedure for selecting model parameters can be implemented, given a probable pilot control strategy. In analyzing a pair of piloting tasks for which flight and simulation data are available, the methodology correctly predicted the existence of simulator fidelity problems. The methodology permitted the analytical evaluation of a change in simulator characteristics and indicated that a major source of the fidelity problems was a visual time delay in the simulation.

Hess, Ronald A.↗

Goddard Mission Analysis System (GMAS)

Written to simulate complex satellite orbits including attitude control and orbital maneuvers, GMAS also performs shadow and station coverage studies and graph-selected orbital parameters for two satellites. Written in FORTRAN and ASSEMBLER.

Mcgarry, F. E.↗

Reflecting boundary conditions for graded p-n junctions

In a graded junction, the formalism for handling reflecting boundary conditions must be modified. Since a significant drift term is present, zero recombination velocity at the surface does not imply a zero excess carrier gradient but rather zero overall flux. A model for analyzing p-n junctions fabricated by implantation or diffusion is presented, assuming the dominant recombination mechanism in the graded region is Auger. The model enables optimization of diode design. By proper selection of parameters, mainly by reducing surface concentration or by increasing the steepness of the dopant profile, it is possible to drastically reduce the saturation current generated by the graded region.

Schacham, S. E.↗

Concave-outward slow shocks in coronal mass ejections

Formation of slow shocks in a simplified model corona consisting of closed magnetic field lines near the coronal base with overlying open magnetic field lines is analyzed. An increase in the magnetic field strength in the closed region is utilized to drive the corona outward, generating slow shocks for a suitable selection of parameters. The study demonstrates that concave-upward slow shocks can be formed in a magnetic environment, and provides evidence that nonlinear manifestations of all three wave modes (slow, intermediate, and fast) can occur as the corona adjusts from ambient conditions to those produced by the driver. The results show the existence of nonlinear disturbances due to all three wave modes in the coronal response to the expanding driver magnetic fields.

Steinolfson, R. S.↗

An analysis of the least-squares problem for the DSN systematic pointing error model

A systematic pointing error model is used to calibrate antennas in the Deep Space Network. The least squares problem is described and analyzed along with the solution methods used to determine the model's parameters. Specifically studied are the rank degeneracy problems resulting from beam pointing error measurement sets that incorporate inadequate sky coverage. A least squares parameter subset selection method is described and its applicability to the systematic error modeling process is demonstrated on Voyager 2 measurement distribution.

Alvarez, L. S.↗

Use of system identification techniques for improving airframe finite element models using test data

A method for using system identification techniques to improve airframe finite element models was developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

Hanagud, Sathya V.↗

A general graphical user interface for automatic reliability modeling

Reported here is a general Graphical User Interface (GUI) for automatic reliability modeling of Processor Memory Switch (PMS) structures using a Markov model. This GUI is based on a hierarchy of windows. One window has graphical editing capabilities for specifying the system's communication structure, hierarchy, reconfiguration capabilities, and requirements. Other windows have field texts, popup menus, and buttons for specifying parameters and selecting actions. An example application of the GUI is given.

Liceaga, Carlos A.↗

Transient natural convection heat and mass transfer in crystal growth

A numerical analysis of transient combined heat and mass transfer across a rectangular cavity is performed. The physical parameters are selected to represent a range of possible crystal growth in solutions. Good agreements with measurement data are observed. It is found that the thermal and solute fields become highly oscillatory when the thermal and solute Grashof numbers are large.

Han, Samuel S.↗

Use of system identification techniques for improving airframe finite element models using test data

A method for using system identification techniques to improve airframe finite element models using test data has been developed and demonstrated. The method uses linear sensitivity matrices to relate changes in selected physical parameters to changes in the total system matrices. The values for these physical parameters were determined using constrained optimization with singular value decomposition. The method was confirmed using both simple and complex finite element models for which pseudo-experimental data was synthesized directly from the finite element model. The method was then applied to a real airframe model which incorporated all of the complexities and details of a large finite element model and for which extensive test data was available. The method was shown to work, and the differences between the identified model and the measured results were considered satisfactory.

Hanagud, Sathya V.↗

Lunar mission aerobrake performance study

Nine lunar mission scenarios were developed to show the transfer vehicle performance benefits of aerobraking into low Earth orbit (LEO) upon Earth return as opposed to an all-propulsive maneuver. The initial mass in LEO (IMLEO) of the lunar transfer vehicle is considered the measure of vehicle performance. Four types of mission profiles in conjunction with two vehicle concepts were used to construct the scenarios. These nine scenarios were designed to represent a broad range of possible lunar missions so that a general knowledge base of aerobraking and lunar transfer vehicle performance levels could be obtained. Also discussed are the mass sensitivities of each transfer vehicle to changes in the selected design parameters: Isp, crew module mass, payload to surface, and aerobrake mass fraction. A parametric study was performed on two of the mission scenarios to help quantify the performance benefits by adding a set of drop tanks to the vehicle. The parametric study also provides partial derivatives which show the sensitivities of IMLEO to the four design parameters listed. A ranking is given based on vehicle performance.

Mulqueen, J.↗

Study and Development of an Air Conditioning System Operating on a Magnetic Heat Pump Cycle

This report describes the design of a laboratory scale demonstration prototype of an air conditioning system operating on a magnetic heat pump cycle. Design parameters were selected through studies performed by a Kennedy Space Center (KSC) System Simulation Computer Model. The heat pump consists of a rotor turning through four magnetic fields that are created by permanent magnets. Gadolinium was selected as the working material for this demonstration prototype. The rotor was designed to be constructed of flat parallel disks of gadolinium with very little space in between. The rotor rotates in an aluminum housing. The laboratory scale demonstration prototype is designed to provide a theoretical Carnot Cycle efficiency of 62 percent and a Coefficient of Performance of 16.55.

Wang, Pao-Lien↗

Configuration control of seven-degree-of-freedom arms

A seven degree of freedom robot arm with a six degree of freedom end effector is controlled by a processor employing a 6 by 7 Jacobian matrix for defining location and orientation of the end effector in terms of the rotation angles of the joints, a 1 (or more) by 7 Jacobian matrix for defining 1 (or more) user specified kinematic functions constraining location or movement of selected portions of the arm in terms of the joint angles, the processor combining the two Jacobian matrices to produce an augmented 7 (or more) by 7 Jacobian matrix, the processor effecting control by computing in accordance with forward kinematics from the augmented 7 by 7 Jacobian matrix and from the seven joint angles of the arm a set of seven desired joint angles for transmittal to the joint servo loops of the arm. One of the kinematic functions constraints the orientation of the elbow plane of the arm. Another one of the kinematic functions minimizes a sum of gravitational torques on the joints. Still another kinematic function constrains the location of the arm to perform collision avoidance. Generically, one kinematic function minimizes a sum of selected mechanical parameters of at least some of the joints associated with weighting coefficients which may be changed during arm movement. The mechanical parameters may be velocity errors or gravity torques associated with individual joints.

Seraji, Homayoun↗

Design characteristics of a heat pipe test chamber

LeRC has designed a heat pipe test facility which will be used to provide data for validating heat pipe computer codes. A heat pipe test chamber that uses helium gas for enhancing heat transfer was investigated. The conceptual design employs the technique of guarded heating and guarded cooling to facilitate accurate measurements of heat transfer rates to the evaporator and from the condenser. The design parameters are selected for a baseline heat pipe made of stainless steel with an inner diameter of 38.10 mm and a wall thickness of 1.016 mm. The heat pipe operates at a design temperature of 1000 K with an evaporator radial heat flux of 53 W/sq. cm.

Baker, Karl W.↗