Search NASA⌕ Search

SEARCH · Search NASA

Results for “static testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Sensitivity Effects of High Temperature Overhead Conductors to Line Rating Variables

For traditional overhead transmission lines, the maximum allowable conductor operating temperature on ASCR, AAC, or AAAC lines for determining the static line ratings can be quite low, typically well under 100 C. At these low temperatures, the primary driver for determining static line ratings are assumptions made about the wind speed and direction and the ambient temperature. Assumptions for solar loading and emitted thermal radiation, driven by line emissivity and absorptivity, are secondary factors, and only provide small changes to the static ratings. However, when considering newer high temperature conductors such as ACSS, ACCR, ZTACIR, and ACCC® the maximum allowable conductor temperatures can be significantly higher, up to 250° C. This higher temperature shifts the importance of the emissivity assumptions of the overhead transmission line, due to the nature of the T4 dependence of the radiative heat loss compared to the T1 dependence of the convective heat loss, as well as shifting the dependency on local wind conditions. Typical assumptions in the United States for the emissivity/absorptivity of overhead transmission lines in determining the static ratings are to use a value of 0.5 for both parameters or set a value in the range of 0.7 to 0.9. Recent experimental tests at EPRI have shown that higher emissivity aging assumptions may not be valid in some regions of the US, and that actual values may be much lower (0.25-0.45) than older studies have predicted (0.8-0.9). Here, the assumptions of different US Regional Transmission Operators (RTOs) and different utilities within RTOs are examined for the static ratings for traditional lower operating temperatures up to 100° C as well as with the higher maximum temperature conductors associated with newer conductor designs at 250° C. The sensitivity of the static ratings is examined at both lower and higher temperature conductors with respect to overhead line emissivity and absorptivity, wind speed, wind direction, and solar loading, and ambient temperature. It is shown that the effects of the conductor absorptivity, solar flux and ambient temperature on the static rating are increased when the transmission line has a lower maximum conductor temperature. The effects of the conductor emissivity, wind direction and wind speed have increased effects on the static rating when the transmission line has a higher maximum conductor temperature. In addition, example weather data is used to calculate the conductor temperature with different line emissivity and absorptivity assumptions. This shows the effect of assumptions made for emissivity only has a minor impact for low temperature lines, but for high temperature transmission lines can cause a 150-200° C temperature swing.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Rotating Detonation Combustion for Gas Turbines: Modeling and System Synthesis to Exceed 65% Efficiency Goal (Phase II)

As of May 2019, all RDE test hardware and test operations were completed for this program. Over 700 hot fire tests were conducted at 4 facilities with 7 RDE assemblies, with the data available for future analysis. In particular, measured static and dynamic pressure and computational fluid dynamics (CFD) provided basis for pressure gain combustion (PGC) analysis of the Engineering Scale RDE. It was demonstrated via measurements and CFD that a carefully designed diffuser can recover some total pressure of the highly oscillatory RDE exhaust. In general, the isolator/injector is largest contributor of pressure losses; however a low loss design was demonstrated that improves significantly on previous natural-gas/air RDEs. Also, a tailored injector and mixing technique was demonstrated that allowed NG-air RDE operation with overall equivalence ratio of less than 0.6. CFD models by AR, the UofM and Purdue University were extensively used throughout the program to refine diffuser design for improved pressure recovery, to simulate injection and mixing, to estimate turbine interaction, to estimate combustor pressure gain anchored with test data and to provide input to other design and analytical tasks. CFD analyses were completed for many of the configurations tested at Purdue with the 13.4” RDE including the shark fin and low area ratio isolators. Results were compared favorably to available hot fire test particle image velocimetry (PIV) measurements and wave speeds. The results of these CFD analyses suggest a modest pressure gain of 33% with a sufficiently low area ratio isolator. A thermodynamic power plant system model was set up which utilizes an RDE combustor. The performance of the RDE combustor module was scaled based on measurements from the Engineering Scale RDE tests with low loss injector and tailored fuel flow. This combined model indicates potential for significant plant efficiency improvement. The successful tailored fuel injection test result with lower than .6 equivalence ratio has implication that a power plant can use a RDE combustor configuration where all the air flows through the combustion zone thereby not requiring a bypass mixer. In this configuration, the results of the natural gas combined cycle (NGCC) plant system indicate net efficiency of 66.4%.

02 PETROLEUM↗

Mechanisms Engineering Test Loop (METL) Operations and Testing Report (FY2020)

This report documents the operations and testing that was performed at the Mechanisms Engineering Test Loop (METL) during FY2020. The METL facility had a very successful second year of operations having logged over 730 days (as of September 19, 2020) of operations with molten sodium either flowing or static. The METL piping and vessel system was filled with sodium on September 19, 2018 after a successful transfer of sodium from fifteen 55-gallon drums. FY2020 saw the successful reconditioning and insertion of the Gear Test Assembly (GTA) for its second round of testing, the full use of the 18-inch Flexi-Cask system, the second extraction of the GTA from METL, and the removal of sodium from the GTA test article by the carbonation process followed by an alcohol wash. In addition, METL is being prepared to support a second larger experiment, a thermal hydraulic experiment, called Thermal Hydraulic Experimental Test Article (THETA).

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Parametric Testing and Evaluation of a Novel Biphasic Absorption Process for Post-Combustion Carbon Capture

A novel biphasic CO2 absorption process (BiCAP) is being developed at the University of Illinois. BiCAP is enabled by using a new class of biphasic solvents developed based on multi-property criteria for postcombustion carbon capture. The process was previously demonstrated at the lab-scale, including in 10 kWe absorption and desorption column systems. In the current study, the process has been scaled up by building and testing a 40 kWe integrated capture skid at a power plant. Parametric tests for two biphasic solvents were conducted with the synthetic flue gas made of bottle CO2 gas and air to validate the performance and operational flexibility of the unit with respect to varying process or operating conditions. Operation of the phase separator, which is unique equipment to BiCAP, was verified to be stable and efficient. Two liquid phases could be separated via static settlement based on a density difference and >90% of the CO2 absorbed was concentrated in the separated CO2-rich phase. Results of parametric tests showed that the minimum heat duty appeared at the optimal stripping pressure. A higher stripping temperature was more favourable to improve overall energy performance. Introducing a secondary cold solvent feed stream to the top of the stripper via bypassing the cross heat exchanger helped reduce the heat loss carried with water vapour. Test results also revealed that the heat duty requirement was comparable when the CO2 concentration in flue gas decreased from ~11 to 4 vol.% as the phase separation decoupled the absorption and desorption steps in BiCAP. Under typical steady-state conditions, both biphasic solvents lowered the process heat duty by >40% compared with the reference 30 wt.% monoethanolamine solvent.

Absorption↗

Nonlinear bleaching, absorption, and scattering of 532-nm-irradiated plasmonic nanoparticles

Single-pulse irradiation of Au and Ag suspensions of nanospheres and nanodisks with 532-nm 4-ns pulses has identified complex optical nonlinearities while minimizing material damage. For all materials tested, we observe competition between saturable absorption (SA) and reverse SA (RSA), with RSA behavior dominating for intensities above {approx}50 MW/cm{sup 2}. Due to reduced laser damage in single-pulse experiments, the observed intrinsic nonlinear absorption coefficients are the highest reported to date for Au nanoparticles. We find size dependence to the nonlinear absorption enhancement for Au nanoparticles, peaking in magnitude for 80-nm nanospheres and falling off at larger sizes. The nonlinear absorption coefficients for Au and Ag spheres are comparable in magnitude. On the other hand, the nonlinear absorption for Ag disks, when corrected for volume fraction, is several times higher. These trends in nonlinear absorption are correlated to local electric field enhancement through quasi-static mean-field theory. Through variable size aperture measurements, we also separate nonlinear scattering from nonlinear absorption. For all materials tested, we find that nonlinear scattering is highly directional and that its magnitude is comparable to that of nonlinear absorption. These results indicate methods to improve the efficacy of plasmonic nanoparticles as optical limiters in pulsed laser systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of high-speed shaft bearing loads in wind turbine gearboxes through dynamometer testing

Many wind turbine gearboxes require repair or replacement well before reaching the end of their design life. The most common failure is bearing axial cracks, commonly called white etching cracks (WECs), which typically occur in the inner raceways of the high-speed parallel-stage rolling element bearings. Although the root causes of WECs are debated, one theory is that they are related to routine dynamic operating conditions and occasional transient events prevalent in wind turbines that can result in high bearing stress and sliding of the rolling elements. Here, this paper examined wind turbine gearbox high-speed shaft bearing loads and stresses through modeling and full-scale dynamometer testing. Bearing outer race loads were directly measured and predicted using a variety of modeling tools in normal operations, misaligned conditions, and transient events particularly prone to bearing sliding. Test data and models of bearing loads were well correlated. Neither operational misalignment due to rotor moments nor static generator misalignment affected the bearing loads when compared with pure-torque conditions. Thus, it is not likely that generator misalignment is a causal factor of WECs. In contrast, during transient events, the bearings experienced alternating periods of high stress, torque reversals, and loads under the minimum requisite at high rotating speeds while showing indications of sliding, all of which could be related to the formation of WECs.

17 WIND ENERGY↗

Stress-constrained topology optimization of lattice-like structures using component-wise reduced order models

We report lattice-like structures can provide a combination of high stiffness with light weight that is useful in many applications, but a resolved finite element mesh of such structures results in a computationally expensive discretization. This computational expense may be particularly burdensome in many-query applications, such as optimization. We develop a stress-constrained topology optimization method for lattice-like structures that uses component-wise reduced order models as a cheap surrogate, providing accurate computation of stress fields while greatly reducing run time relative to a full order model. We demonstrate the ability of our method to produce large reductions in mass while respecting a constraint on the maximum stress in a pair of test problems. The ROM methodology provides a speedup of about 150x in forward solves compared to full order static condensation and provides a relative error of less than 5% in the relaxed stress.

97 MATHEMATICS AND COMPUTING↗

Investigation of shear-banding mechanism in fully dense nanocrystalline Ni sheet

Evolution of shear banding in fully dense electrodeposited nanocrystalline Ni was successfully monitored by using a digital image correlation technique under a quasi-static uniaxial tensile load. To investigate the microscopic physical mechanism of the shear banding, in-situ tensile testing for the nanocrystalline Ni sample was conducted in a transmission electron microscope and fracture surface of the sample was examined by field emission scanning electron microscope. The results suggest that grain boundary migration based on atomic diffusion is a main carrier of the shear banding.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Carbon dioxide/water foams stabilized with a zwitterionic surfactant at temperatures up to 150 °C in high salinity brine

According to the article, stabilization of CO 2 -in-water (C/W) foams with surfactants at high temperature and high salinity conditions is challenging given limitations in the solubility and thermal stability of surfactants, particularly for surfactants other than anionic ones. Here we show that a single zwitterionic surfactant, cetyl betaine (CH 3 (CH 2 ) 15 N + (CH 3 ) 2 CH 2 COO - ), stabilizes viscous C/W foam (>15 cP) in crushed limestone (76-Darcy) at a temperature up to 150 °C and over a wide range in salinity up to 22% total dissolved solids (TDS) at superficial velocity of 940 ft/day. According to liquid chromatography mass spectrometry (LC/MS), cetyl betaine has high thermal stability with negligible chemical degradation after incubation at 135 °C for 30 days. Interfacial tension (IFT) at the C/W interface was reduced significantly from ~37 mN/m to <5 mN/m with the addition of 0.08 mmol/L of cetyl betaine. Relative to ionic surfactants, the relatively weak electrostatic repulsion between the local charges in the headgroup is shown to produce strong adsorption at the C/W interface (~134 Å2/molecule), resulting in generation of viscous foam (~6 cP) even in pure water without added salt. At a low superficial velocity of 6 ft/day (shear rate 45 s -1 ) in a beadpack, foam was still formed with cetyl betaine. Static adsorption of cetyl betaine on carbonates was on the order of 1 mg/m 2 , and core flood test also proved that cetyl betaine could stabilize viscous C/W foam (>20 cP) within 6 pore volumes of injection at 120 °C. The surfactant stabilized viscous C/W foam at low oil fractions and broke in the presence of large fractions of oil, both of which are desirable in CO 2 mobility control and oil displacement. The ability to form foams at high temperatures and over a wide range in salinity is important for various practical applications including CO 2 enhanced oil recovery, fracturing with energized fluids and CO 2 sequestration.

nuclear (including radiation effects), carbon sequ↗

Static characterization of a soft elastomeric capacitor for non destructive evaluation applications

A large and flexible strain transducer consisting of a soft elastomeric capacitor (SEC) has been proposed by the authors. Arranged in a network setup, the sensing strategy offers tremendous potential at conducting non-destructive evaluation of large-scale surfaces. In prior work, the authors have demonstrated the performance of the sensor at tracking strain history, localizing cracks, and detecting vibration signatures. In this paper, we characterize the static performance of the proposed SEC. The characterization includes sensitivity of the signal, and temperature and humidity dependences. Tests are conducted on a simply supported aluminum beam subjected to bending as well as on a free standing sensor. The performance of the SEC is compared against off-the-shelf resistance-based strain gauges with resolution of 1 με. A sensitivity of 1190 pF/ε is obtained experimentally, in agreement with theory. Results also show the sensor linearity over the given level of strain, showing the promise of the SEC at monitoring of surface strain.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Development of a hybrid deterministic/stochastic method for 1D nuclear reactor kinetics

A new method has been implemented for solving the time-dependent neutron transport equation efficiently and accurately. This is accomplished by coupling the hybrid stochastic-deterministic steady-state coarse-mesh radiation transport (COMET) method [1,2] with the new predictor-corrector quasi-static method (PCQM) developed at Politecnico di Torino [3]. In this paper, the coupled method is implemented and tested in 1D slab geometry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Calculation of the static and dynamical correlation energy of pseudo-one-dimensional beryllium systems via a many-body expansion

Due to the importance of both static and dynamical correlation in the bond formation, low-dimensional beryllium systems constitute interesting case studies to test correlation methods. Aiming to describe the whole dissociation curve of extended Be systems we chose to apply the method of increments (MoI) in its multireference (MR) formalism. To gain insight into the main characteristics of the wave function, we started by focusing on the description of small Be chains using standard quantum chemical methods. In a next step we applied the MoI to larger beryllium systems, starting from the Be{sub 6} ring. The complete active space formalism was employed and the results were used as reference for local MR calculations of the whole dissociation curve. Although this is a well-established approach for systems with limited multireference character, its application regarding the description of whole dissociation curves requires further testing. Subsequent to the discussion of the role of the basis set, the method was finally applied to larger rings and extrapolated to an infinite chain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Inferring the gravitational potential of the Milky Way with a few precisely measured stars

The dark matter halo of the Milky Way is expected to be triaxial and filled with substructure. It is hoped that streams or shells of stars produced by tidal disruption of stellar systems will provide precise measures of the gravitational potential to test these predictions. We develop a method for inferring the Galactic potential with tidal streams based on the idea that the stream stars were once close in phase space. Our method can flexibly adapt to any form for the Galactic potential: it works in phase-space rather than action-space and hence relies neither on our ability to derive actions nor on the integrability of the potential. Our model is probabilistic, with a likelihood function and priors on the parameters. The method can properly account for finite observational uncertainties and missing data dimensions. We test our method on synthetic data sets generated from N-body simulations of satellite disruption in a static, multi-component Milky Way, including a triaxial dark matter halo with observational uncertainties chosen to mimic current and near-future surveys of various stars. We find that with just eight well-measured stream stars, we can infer properties of a triaxial potential with precisions of the order of 5%-7%. Without proper motions, we obtain 10% constraints on most potential parameters and precisions around 5%-10% for recovering missing phase-space coordinates. These results are encouraging for the goal of using flexible, time-dependent potential models combined with larger data sets to unravel the detailed shape of the dark matter distribution around the Milky Way.

79 ASTRONOMY AND ASTROPHYSICS↗

Holes in the static Einstein universe and a model of the cosmological voids

A spherically symmetric, static model of the cosmological voids is constructed in the framework of the Tolman-Oppenheimer-Volkov equation with the cosmological constant. Extension of the Tooper result (dimensionless form of the TOV equation) is provided for nonzero {lambda}. Then, the equation is simplified in {alpha}{yields}0, {lambda}{yields}0, and {lambda}/{alpha}=const regime, suitable for largest structures in {lambda}-dominated universe. Voids are treated as underdensity regions in the static Einstein universe. Both overdensity and underdensity (relative to static universe) solutions exist. They are identified with standard astrophysical spherical objects and voids, respectively. The model is tested against observed properties (the radius - the central density relation) and density profiles of voids. Analytical formulas for radial density contrast profile and radii of the voids are derived. Some consequences for cosmological N-body simulations are suggested. Hints on the dark matter/dark energy EOS filling the voids are provided.

79 ASTRONOMY AND ASTROPHYSICS↗

Predicting Dynamic-to-Static Correction Factor from Petrophysical Data and Chemostratigraphy using Unsupervised Machine Learning

Estimating static mechanical properties of stratigraphic layers is critical for optimizing subsurface engineering applications. To estimate dynamic-to-static correction factor F ds (static-to-dynamic Young’s modulus ratio) across the Caney shale interval in Oklahoma, USA, we integrated triaxial test measurements and petrophysical data, including well logs and X-ray fluorescence (XRF) using unsupervised machine learning (ML). We used a novel workflow that includes principal component analysis (PCA) to reduce data set dimensionality of well logs and XRF data sets—both separately and combined—creating three scenarios, and later applied inverse distance weighting (IDW) to derive F ds profiles for these scenarios. Furthermore, we applied K-means clustering on each scenario to predict depositional facies, and built a stiffness zonation profile through chemostratigraphic analysis of the terrigenous elements to validate the predicted F ds . The predicted F ds profile from each scenario using the PCA-IDW method was compared with the constant F ds approach from our previous study by calculating the root mean square error (RMSE). The combined data sets scenario yielded the lowest RMSE value of 0.113, while the RMSE values for the well logs and XRF scenarios were 0.131 and 0.129, respectively. In addition, the predicted F ds from the XRF scenario well-matched the stiffness zonation from the chemostratigraphic analysis that was built using the optimized K-means clustering of nine clusters for that scenario. These methods and findings offer a valuable tool for refining lithological classification and improving the F ds profile, potentially enhancing drilling and stimulation strategies for subsurface energy engineering applications.

clastic rock↗

Effect of Part Size, Displacement Rate, and Aging on Compressive Properties of Elastomeric Parts of Different Unit Cell Topologies Formed by Vat Photopolymerization Additive Manufacturing

Due to its ability to achieve geometric complexity at high resolution and low length scales, additive manufacturing (AM) has increasingly been used for fabricating cellular structures (e.g., foams and lattices) for a variety of applications. Specifically, elastomeric cellular structures offer tunability of compliance as well as energy absorption and dissipation characteristics. However, there are limited data available on compression properties for printed elastomeric cellular structures of different designs and testing parameters. In this work, the authors evaluate how unit cell topology, part size, the rate of compression, and aging affect the compressive response of polyurethane-based simple cubic, body-centered, and gyroid structures formed by vat photopolymerization AM. Finite element simulations incorporating hyperelastic and viscoelastic models were used to describe the data, and the simulated results compared well with the experimental data. Of the designs tested, only the parts with the body-centered unit cell exhibited differences in stress–strain responses at different part sizes. Of the compression rates tested, the highest displacement rate (1000 mm/min) often caused stiffer compressive behavior, indicating deviation from the quasi-static assumption and approaching the intermediate rate response. The cellular structures did not change in compression properties across five weeks of aging time, which is desirable for cushioning applications. This work advances knowledge on the structure–property relationships of printed elastomeric cellular materials, which will enable more predictable compressive properties that can be traced to specific unit cell designs.

36 MATERIALS SCIENCE↗

Evaluating the Durability of Balance of Systems Components Using Combined-Accelerated Stress Testing

The degradation of photovoltaic (PV) balance of systems (BoS) components is not well-studied, but the consequences include offline modules, strings, and inverters; system shutdown; arc faults; and fires. A utility provider experienced a ~30% failure rate in their power transfer chain, originally attributed to branch connectors. Field-failed specimen assemblies were therefore examined, consisting of cable connector, branch connector, and discrete fuse components. Previous papers and presentations have focused on the development of the test method using a benchtop prototype. This presentation covers the early results of C-AST aging of static and dynamic specimens.

balance of systems↗

Dense Plasma X-ray Scattering: Methods and Applications

We have developed accurate x-ray scattering techniques to measure the physical properties of dense plasmas. Temperature and density are inferred from inelastic x-ray scattering data whose interpretation is model-independent for low to moderately coupled systems. Specifically, the spectral shape of the non-collective Compton scattering spectrum directly reflects the electron velocity distribution. In partially Fermi degenerate systems that have been investigated experimentally in laser shock-compressed beryllium, the Compton scattering spectrum provides the Fermi energy and hence the electron density. We show that forward scattering spectra that observe collective plasmon oscillations yield densities in agreement with Compton scattering. In addition, electron temperatures inferred from the dispersion of the plasmon feature are consistent with the ion temperature sensitive elastic scattering feature. Hence, theoretical models of the static ion-ion structure factor and consequently the equation of state of dense matter can be directly tested.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗