Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Preliminary modeling of triply periodic minimal surface (TPMS) structures using RELAP5-3D

With the United States Department of Energy (DOE)’s goal of quadrupling the nation’s nuclear energy supply by 2050, and with the Advanced Fuels Campaign pushing for new types of advanced reactor fuels and geometries, the need has arisen for new nuclear fuel designs. One such design is to swap out current nuclear fuel geometries in exchange for another type of geometry, called a Triply Periodic Minimal Surface (TPMS). TPMSs are self-supporting, infinitely repeating lattices—attributes that lend themselves well to additive manufacturing. These surfaces also possess enhanced heat transfer properties thanks to their internal area changes and large surface-area-to-volume ratios. Their drawback, however, is an increased pressure drop. Given the small amount of correlations and data (Reynolds numbers in the 2,000–8,000 range), and the minimal amount of experience so far obtained by modeling TPMS structures using 1D systems codes such as the Reactor Excursion and Leak Analysis Program (RELAP5-3D), further research into this topic was needed. Using data from the University of Wisconsin - Madison (UW), curve fits were created for both a Heat Transfer Coefficient (HTC) correlation and a Darcy friction factor empirical coefficient correlation. The curves’ coefficients and multipliers were then output and utilized in RELAP5-3D models of two upcoming experiments—Flow Loop for INFLUX Pressure drop (FLIP) and Microreactor Agile Non-nuclear Experimental Test (MAGNET)—aimed at increasing the available data for Reynolds numbers to the 16,000–36,000 range for TPMS structures. The models were run under the conditions utilized by a Computational Fluid Dynamics (CFD) analysis performed by another group at Idaho National Laboratory. Only CFD pressure drop values were obtained from the FLIP test, and those values showed that the RELAP5-3D models had a lower rate of pressure increase in comparison to the CFD values. In addition, there seemed to be a vertical shift upward in the pressure drop for both models whenever the TPMS porosity decreased, and the RELAP5-3D models showed a higher vertical shift in comparison to the CFD values. The MAGNET results did not correspond to any CFD or experimental results against which they could be compared, so they were instead compared against the proposed CFD input conditions. These values were then compared with each other to make sure the model seemed to be performing as expected, paving the way for future tests that can be run for the purpose of further analyses and comparisons. The pressure drop increased with temperature and mass flow rate independently. The temperature change would decrease with increasing mass flow rate and temperature, which was just as we expected based on the fact that the lower viscosity and decreased density would result in higher friction and churning losses. The last metric that was assessed was the enthalpy flow change, which increased with increasing mass flow rate and decreasing temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Deep Learning Estimation of Daily Ground–Level NO 2 Concentrations from Remote Sensing Data

The limited number of nitrogen dioxide (NO 2 ) surface measurements calls for the development of highly accurate approaches to estimating surface NO 2 concentrations. In this study, we leverage a new satellite instrument, the TROPOspheric Monitoring Instrument (TROPOMI), along with other predictor variables, to estimate daily surface NO 2 concentrations over Texas in 2019. We use the deep convolutional neural network (Deep-CNN), an advanced deep learning algorithm, to obtain estimates and achieve a correlation coefficient (R) of 0.91, an index of agreement (IOA) of 0.95, and a mean absolute bias (MAB) of 1.75 ppb in surface NO 2 estimation. Additionally, we leverage a novel approach, SHapley Additive exPlanations (SHAP), to describe how Deep-CNN understands each predictor variable. The SHAP results show that the Deep-CNN model has an advanced understanding of the dataset, revealing that TROPOMI closely captures levels of NO 2 . In addition, we show the superiority of our Deep-CNN model at estimating surface NO 2 over other well-known machine learning and regression models in the field, including the support vector machines (SVM), random forest (RF), and multiple linear regression (MLR). Although SVM and RF show strong capabilities at estimating surface NO 2 concentrations, their accuracy is inferior to that of the Deep-CNN model, ranking second and third in model accuracy in this study. The MLR, however, shows a poor ability at NO 2 estimation and ranks last among all models. Furthermore, testing the impact of sample size on model performance, we also show that, compared to other models, Deep-CNN needs more samples to trigger its strength at surface NO 2 estimation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Material Extrusion Printing of Poly(Acrylonitrile‐Styrene‐Acrylate) and Poly(Acrylonitrile‐Butadiene‐Styrene) Structures Reinforced with Poly(Phenylene Oxide) Additives for Improved Thermomechanical Properties and their Surface Analysis by Time‐of‐Flight Secondary Ion Mass Spectrometry

Fused filament fabrication offers the ability to 3D print complex geometries made from plastic filament materials; however, these parts are mechanically outperformed by parts created by traditional fabrication methods. To overcome this challenge, a high-performance polymer poly(2,6-dimethyl-1,4-phenylene oxide) (PPO) is incorporated as an additive into two common engineering thermoplastics, poly(acrylonitrile-styrene-acrylate) (ASA) and poly(acrylonitrile-butadiene-styrene) (ABS). Structures printed from these polymer blends are more mechanically robust compared to those prepared from the parent polymers, with low loading levels (1–5 wt%) of PPO improving the elastic strength by up to ≈30% relative to the parent terpolymers. Even at higher loading levels (10 and 20 wt% PPO), there is no evidence of additive aggregation in the model thin films, which is supported by compositional analysis of the copolymers and chemical analysis via time-of-flight secondary ion mass spectrometry. The enhancements in mechanical properties of ASA and ABS blends appear to be a consequence of homogeneous incorporation of the PPO additive. In conclusion, this work explores expanding materials-property space using miscible blends of engineering thermoplastics to improve mechanical performance as a general approach to overcoming challenges with parts created by melt-based material extrusion printing.

additive manufacturing↗
DOE OSTI2025

Dependence of Exciton Spin Dynamics on Quantum Confinement Dimensionality in CsPbBr 3 Nanocrystals

Semiconductor nanomaterials offer a promising platform to produce optically addressable spins for use in quantum technologies. Here, in this study, we examine CsPbBr 3 nanospheres, cubes, and rods spanning the zero-dimensional (0D) to three-dimensional (3D) transition to investigate the influence of dimensionality and shape on exciton spin decoherence. Using circularly polarized transient absorption spectroscopy, we find that the spin relaxation rate is independent of the surface to volume ratio and instead follows a dependence on the length of the shortest dimension. Additionally, differences in surface quality and termination appear to have no effect on the spin relaxation rate for measured materials, and instead the spin relaxation rate is most clearly correlated with the exciton binding energy. Finally, decreasing the dimensionality of the nanomaterials decreases the influence of multiexciton interactions on the spin relaxation rate.

CsPbBr3 nanocrystals↗
NASA NTRS1995

Thruster momentum transfer studies and magnetoplasmadynamic (MPD) thruster use in materials/surface modification

This research project involves the systematic study of the MPD thruster for dual uses. Though it was designed as a thruster for space vehicles, the characteristics of the plasma make it an excellent candidate for industrial applications. This project will seek to characterize the system for use in materials processing and characterization. Crystals grown at Fisk University for use with solid state detectors will be studied. Surface modification on ZnCdTe, CdTe, and ZnTe will be studied using AFM, XPS and SAES. In addition to the surface modification studies, design work on a momentum transfer measurement device has been completed. The design and limitations of the device will be presented.

Thompson, E.↗
NASA NTRS2017

Viscous Three-Dimensional Simulation of Flow in an Axial Low Pressure Compressor at Engine Icing Operating Points

Viscous three-dimensional simulations of the Honeywell ALF502R-5 low pressure compressor (sometimes called a booster) using the NASA Glenn code GlennHT have been carried out. A total of ten simulations were produced. Five operating points are investigated, with each point run with two different wall thermal conditions. These operating points are at, or near, points where engine icing has been determined to be likely. In the future, the results of this study will be used for further analysis such as predicting collection efficiency of ice particles and ice growth rates at various locations in the compressor. A mixing plane boundary condition is used between each blade row, resulting in convergence to steady state within each blade row. The k-omega turbulence model of Wilcox, combined with viscous grid spacing near the wall on the order of one, is used to resolve the turbulent boundary layers. For each of the operating points, heat transfer coefficients are generated on the blades and walls. The heat transfer coefficients are produced by running the operating point with two different wall thermal conditions and then solving simultaneously for the heat transfer coefficient and adiabatic wall temperature at each point. Average Nusselt numbers are calculated for the most relevant surfaces. The values are seen to scale with Reynolds number to approximately a power of 0.7. Additionally, images of surface distribution of Nusselt number are presented. Qualitative comparison between the five operating points show that there is relatively little change in the character of the distribution. The dominant observed effect is that of an overall scaling, which is expected due to Reynolds number differences. One interesting aspect about the Nusselt number distribution is observed on the casing (outer diameter) downstream of the exit guide vanes (EGVs). The Nusselt number is relatively high between the pairs of EGVs, with two lower troughs downstream of each EGV trailing edge. This is of particular interest since rather complex ice shapes have been observed in that region.

compressor↗
DOE OSTI2022

Multifunctional Thiol-Containing Additives for Improved Photoluminescence and Photovoltaic Performance of Cs 0.15 FA 0.85 PbI 3 Perovskites

Thiol containing molecules as both interfacial surface ligands and additives are promising modulators for enhancing photoluminescence (PL) properties, stability, and photovoltaic (PV) performance of metal halide perovskites. However, alkanethiols are much more effective for improving photoluminescence (PL) intensity and stability in metal halide perovskite nanocrystals than in their thin film analogues. Herein, we investigate how additional functional groups on a pyrimidine core can alter thiol reactivity and influence the PL, stability, and PV performance of organic metal halide perovskites. Through an investigation of five different pyrimidine derivatives, it is shown that all derivatives containing thiol groups form thiolates in the presence of the perovskite precursors and increase the photoluminescence intensity of the perovskite film. The largest all-around improvement to the PL intensity, stability, and photovoltaic performance of Cs 0.15 FA 0.85 PbI 3 perovskites is realized through the addition of a hydroxyl group combined with a trifluoromethyl group to form 4-hydroxy-6-(trifluoromethyl)pyrimidine-2-thiol. Furthermore, this investigation helps illuminate how combinations of functional groups can be employed to further increase the beneficial effects over monofunctional additives in organic metal halide perovskites.

14 SOLAR ENERGY↗
NASA NTRS2018

Additive Construction with Mobile Emplacement: Multifaceted Planetary Construction Materials Development

The National Aeronautics and Space Administration's Additive Construction with Mobile Emplacement (ACME) project is developing construction materials with which infrastructure elements, including habitats, will be additively constructed for planetary surface missions. These materials must meet requirements such as the ability to be produced from available in-situ resources to eliminate the cost of launching materials from Earth, the ability to be emplaced via three dimensional building techniques, the ability to resist aging in extreme environments including radiation and micrometeorite bombardment, and the ability to provide the necessary structural integrity for a given building. This paper reviews the constraints placed on such planetary construction materials and details the work of the ACME team in characterizing materials that could one day construct planetary surface structures on Mars or the Moon. Material compositions, compressive strength, and requirements for additive construction on planetary surfaces are discussed. Due to the multifunctional requirements of the material, an optimization is necessary to balance between the site-specific regolith composition, emplacement via additive construction techniques, and characteristics of the final structure.

simulant↗
DOE OSTI2023

Influence of local symmetry on lattice dynamics coupled to topological surface states

Herein we investigate coupled electron-lattice dynamics in the topological insulator Bi 2 Te 3 with time-resolved photoemission and time-resolved x-ray diffraction. It is well established that coherent phonons can be launched by optical excitation, but selection rules generally restrict these modes to zone-center wave vectors and Raman-active branches. We find that the topological surface state couples to additional modes, including a continuum of surface-projected bulk modes from both Raman and infrared branches, with possible contributions from surface-localized modes when they exist. Our calculations show that this surface vibrational spectrum occurs naturally as a consequence of the translational and inversion symmetries broken at the surface, without requiring the splitting-off of surface-localized phonon modes. The generality of this result suggests that coherent phonon spectra are useful by providing unique fingerprints for identifying surface states in more controversial materials. These effects may also expand the phase space for tailoring surface state wave functions via ultrafast optical excitation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1980

Simulation of electromagnetic aspects of lightning

Electromagnetic processes peculiar to the direct-strike case are reviewed with respect to their implications for lightning electromagnetic simulation. At low frequencies (quasistatic) there are important surface-charge-density and corona effects in addition to the surface-current-density effects. At resonant frequencies the frequency-spectral content of the excitation and properties of the arc (attachment, detachment, time history, spatial distribution, resistance, etc.) are significant. Of great complexity in all this are nonlinear aspects of the arc and corona around the system of interest. The complexity of these various processes requires rigor in the simulator design. Potential simulation concepts are presented and their relative merits are discussed.

Baum, C. E.↗
NASA NTRS1991

Triton's global heat budget

Internal heat flow from radioactive decay in Triton's interior along with absorbed thermal energy from Neptune total 5 to 20 percent of the insolation absorbed by Triton, thus comprising a significant fraction of Triton's surface energy balance. These additional energy inputs can raise Triton's surface temperature between approx. 0.5 to 1.5 K above that possible with absorbed sunlight alone, resulting in a factor of approx. 1.5 to 2.5 increase in Triton's basal atmospheric pressure. If Triton's internal heatflow is concentrated in some areas, as is likely, local effects such as enhanced sublimation with subsequent modification of albedo could be quite large. Furthermore, indications of recent albedo change on Triton suggest that Triton's surface temperature and pressure may not now be in steady state, further suggesting that atmospheric pressure on Triton was as much as 10 times higher in the recent past.

Brown, R. H.↗
NASA NTRS1991

Triton's global heat budget

Internal heat flow from radioactive decay in Triton's interior along with absorbed thermal energy from Neptune total 5 to 20 percent of the isolation absorbed by Triton, thus comprising a significant fraction of Triton's surface energy balance. These additional energy inputs can raise Triton's surface temperature between about 0.5 and 1.5 K above that possible with absorbed sunlight alone, resulting in an increase of about a factor of about 1.5 to 2.5 in Triton's basal atmospheric pressure. If Triton's internal heat flow is concentrated in some areas, as is likely, local effects such as enhanced sublimation with subsequent modification of albedo could be quite large. Furthermore, indications of recent global albedo change on Triton suggest that Triton's surface temperature and pressure may not now be in steady state, further suggesting that atmospheric pressure on Triton was as much as ten times higher in the recent past.

Brown, R. H.↗
NASA NTRS2003

Energy Requirements of Hydrogen-utilizing Microbes: A Boundary Condition for Subsurface Life

Microbial ecosystems based on the energy supplied by water-rock chemistry carry particular significance in the context of geo- and astrobiology. With no direct dependence on solar energy, lithotrophic microbes could conceivably penetrate a planetary crust to a depth limited only by temperature or pressure constraints (several kilometers or more). The deep lithospheric habitat is thereby potentially much greater in volume than its surface counterpart, and in addition offers a stable refuge against inhospitable surface conditions related to climatic or atmospheric evolution (e.g., Mars) or even high-energy impacts (e.g., early in Earth's history). The possibilities for a deep microbial biosphere are, however, greatly constrained by life s need to obtain energy at a certain minimum rate (the maintenance energy requirement) and of a certain minimum magnitude (the energy quantum requirement). The mere existence of these requirements implies that a significant fraction of the chemical free energy available in the subsurface environment cannot be exploited by life. Similar limits may also apply to the usefulness of light energy at very low intensities or long wavelengths. Quantification of these minimum energy requirements in terrestrial microbial ecosystems will help to establish a criterion of energetic habitability that can significantly constrain the prospects for life in Earth's subsurface, or on other bodies in the solar system. Our early work has focused on quantifying the biological energy quantum requirement for methanogenic archaea, as representatives of a plausible subsurface metabolism, in anoxic sediments (where energy availability is among the most limiting factors in microbial population growth). In both field and laboratory experiments utilizing these sediments, methanogens retain a remarkably consistent free energy intake, in the face of fluctuating environmental conditions that affect energy availability. The energy yields apparently required by methanogens in these sediment systems for sustained metabolism are about half that previously thought necessary. Lowered energy requirements would imply that a correspondingly greater proportion of the planetary subsurface could represent viable habitat for microorganisms.

Hoehler, Tori M.↗
DOE OSTI2019

Epitaxial TiO x Surface in Ferroelectric BaTiO 3 : Native Structure and Dynamic Patterning at the Atomic Scale

Surfaces and interfaces of ferroelectric oxides exhibit enhanced functionality, and therefore serve as a platform for novel nano and quantum technologies. Experimental and theoretical challenges associated with examining the subtle electro-chemo-mechanical balance at metal-oxide surfaces have hindered the understanding and control of their structure and behavior. Here, we combine advanced electron-microscopy and first-principles thermodynamics methods to reveal the atomic-scale chemical and crystallographic structure of the surface of the seminal ferroelectric BaTiO 3 . Here, we show that the surface is composed of a native < 2-nm thick TiOx rock-salt layer in epitaxial registry with the BaTiO 3 . Using electron-beam irradiation, we successfully patterned artificially TiO x sites with sub-nanometer resolution, by inducing Ba escape. Therefore, our work offers electro-chemo-mechanical insights into ferroelectric surface behavior in addition to a method for scalable high-resolution beam-induced chemical lithography for selectively driving surface phase transitions, and thereby functionalizing metal-oxide surfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Alteration of pool boiling heat transfer on metallic surfaces by in situ oxidation

The critical heat flux during pool boiling has been investigated for a range of applications including electrical power generation and thermal management. Reported experimental CHF values during pool boiling of water on flat metallic surfaces, however, show a large discrepancy across studies. Here, we address this discrepancy in CHF values by accounting for oxidation of metallic surfaces during boiling. We studied the effect of in situ oxidation on flat Cu and Ni surfaces by changing the duration that samples were held in saturated water before conducting boiling experiments. The morphology and chemical composition of surfaces after the boiling experiments were analyzed by atomic force microscopy and X-ray photoelectron spectroscopy, respectively. Cu surfaces showed gradually increasing CHF values as the duration in saturated water increased, which could be attributed to the increase in roughness due to the formation of Cu 2 O nanostructures. Conversely, Ni surfaces showed relatively stable CHF and morphology as a nearly flat layer of NiO formed, with one exception: formation of a highly wetting hydroxide, Ni(OH) 2 , on a Ni coupon held in saturated water for 24 h resulted in a uniquely high CHF value, signifying the importance of surface chemistry in addition to morphology. Finally, the fundamental mechanisms resulting in the wide spread of CHF values on metallic surfaces elucidated in this work will lead to more accurate estimation of CHF as well as a deeper mechanistic understanding of CHF values on engineered surfaces.

42 ENGINEERING↗
NASA NTRS1979

On the internal structure of the major satellites of the outer planets

The structures and thermal evolutions of the large icy-satellites of the outer solar system are considered. It is shown (for bodies comparable in size and mass to the Galilean satellites, having sizeable mass fraction of H2O, and with meteoritic abundances of radioactive materials contained within their silicate fractions) that the crust of solid ice over a liquid mantle predicted by conductive heat-transfer calculations is unstable to large-scale solid-state convection. For appropriate material parameters, convective heat-transfer rates are sufficient to freeze a large liquid mantle on a time scale that is short compared to the lifetime of the body. It is also concluded that the ice layer is convecting at the present time. A reevaluation of previous work, using improved values for material parameters and boundary conditions, reverses earlier conclusions and implies a rigid outer crust with resulting long-term stability of surface features to creep deformation. The combination of a rigid crust with active internal convection presents the additional possibility of surface features that are produced and maintained by dynamic internal processes.

Reynolds, R. T.↗
NASA NTRS1985

Improving Emittance of High-Temperature Insulating Tile

Simple addition to ceramic insulating tiles provides backup properties that minimize transfer of heat through tiles when their surfaces become damaged. Addition of 3 percent by weight of 320- or 600-grit silicon carbide powder to ceramic during production results in impregnated tile material that resists overheating. Silicon carbide increases emittance and decreases transmittance of ceramic.

Gzowski, E. R.↗
NASA NTRS2003

Thermomechanical Properties of Interface Modified M40J Carbon/PMR-II-50 Composites

To increase performance and durability of high-temperature composites for potential rocket engine components, it is necessary to optimize wetting and interfacial bonding between high modulus carbon fibers and high-temperature polyimide resins. It has been previously demonstrated that the electro-oxidative shear treatments used by fiber manufacturers are not effective on higher modulus fibers that have fewer edge and defect sites in the surface crystallites. In addition, sizings commercially supplied on most carbon fibers are not compatible with polyimides. In this study, the surface chemistry and energy of high modulus carbon fibers (M40J and M60J, Torray) and typical fluorinated polyimide resins, such as PMR-11-50 were characterized. A continuous desizing system that uses an environmentally friendly chemical- mechanical process was developed for tow level fiber. Composites were fabricated with fibers containing the manufacturer's sizing, desized, and further treated with a reactive finish. Results of room temperature tests show that desizing reduces interface sensitive properties compared to the manufacturer's sizing and that subsequent surface re-treatment with reactive finish increases interface sensitive properties. Properties of thermally aged composites and composites with varying finish concentrations will also be discussed.

Allred, Ronald E.↗