Search NASA⌕ Search

SEARCH · Search NASA

Results for “vortex”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Interaction of an oscillating vortex with a turbulent boundary layer

An oscillating vortex embedded within a turbulent boundary layer was generated experimentally by forcing a periodic lateral translation of a half-delta wing vortex generator. The objective of the experiment was to investigate the possibility that a natural oscillation, or meander, might be responsible for flattened vortex cores observed in previous work, which could also have contaminated previous turbulence measurements. The effect of this forced oscillation was characterized by comparison of measurements of the mean velocities and Reynolds stresses at two streamwise stations, for cases with and without forcing. The Reynolds stresses were affected significantly by the forced oscillation, mainly through contributions from the individual production terms, provided that the vortex was not too diffuse.

Westphal, R. V.↗
NASA NTRS1989

Zero-Gravity Vortex Vent and PVT Gaging System

Space Station and satellite reservicing will require the ability to vent gas on orbit from liquid supply or storage tanks and to gage liquid quantity under microgravity conditions. In zero gravity, (zero-g) the vortex vent is capable of venting gas from a tank of liquid containing gas randomly distributed as bubbles. The concept uses a spinning impeller to create centrifugal force inside a vortex tube within a tank. This creates a gas pocket and forces the liquid through a venturi and back into the tank. Gas is then vented from the gas pocket through a liquid detector and then out through an exhaust port. If the liquid detector senses liquid in the vent line, the fluid is directed to the low-pressure port on the venturi and is returned to the tank. The advantages of this system is that it has no rotating seals and is compatible with most corrosive and cryogenic fluids. A prototype was designed and built at the NASA Johnson Space Center and flown on the KC-135 zero-g aircraft. During these test flights, where microgravity conditions are obtained for up to 30 sec, the prototype demonstrated that less than 0.10 percent of the volume of fluid vented was liquid when the tank was half full of liquid. The pressure volume temperature (PVT) gaging system is used in conjunction with the vortex vent to calculate the amount of liquid remaining in a tank under microgravity conditions. The PVT gaging system is used in conjunction with the vortex vent to gage liquid quantity in zero or low gravity. The system consists of a gas compressor, accumulator, and temperature and pressure instrumentation. To measure the liquid in a tank a small amount of gas is vented from the tank to the compressor and compressed into the accumulator. Pressure and temperature in the tank and accumulator are measured before and after the gas transfer occurs. Knowing the total volume of the tank, the volume of the accumulator, the volume of the intermediate lines, and initial and final pressures and temperatures, the mass of the gas leaving the tank is equated to the mass of the gas entering the accumulator. The volume of liquid remaining in the tank is calculated using the ideal gas law.

Downey, M. G.↗
NASA NTRS1989

Dynamics of a class of vortex rings

The contour dynamics method is extended to vortex rings with vorticity varying linearly from the symmetry axis. An elliptic core model is also developed to explain some of the basic physics. Passage and collisions of two identical rings are studied focusing on core deformation, sound generation and stirring of fluid elements. With respect to core deformation, not only the strain rate but how rapidly it varies is important and accounts for greater susceptibility to vortex tearing than in two dimensions. For slow strain, as a passage interaction is completed and the strain relaxes, the cores return to their original shape while permanent deformations remain for rapidly varying strain. For collisions, if the strain changes slowly the core shapes migrate through a known family of two-dimensional steady vortex pairs up to the limiting member of the family. Thereafter energy conservation does not allow the cores to maintain a constant shape. For rapidly varying strain, core deformation is severe and a head-tail structure in good agreement with experiments is formed. With respect to sound generation, good agreement with the measured acoustic signal for colliding rings is obtained and a feature previously thought to be due to viscous effects is shown to be an effect of inviscid core deformation alone. For passage interactions, a component of high frequency is present. Evidence for the importance of this noise source in jet noise spectra is provided. Finally, processes of fluid engulfment and rejection for an unsteady vortex ring are studied using the stable and unstable manifolds. The unstable manifold shows excellent agreement with flow visualization experiments for leapfrogging rings suggesting that it may be a good tool for numerical flow visualization in other time periodic flows.

Shariff, Karim↗
NASA NTRS1989

Ground evaluation of seeding an in-flight wingtip vortex using infrared imaging flow visualization technique

An experimental simulation of an in-flight wingtip vortical flow visualization technique uses infrared imaging to observe strong and concentrated vortices. This experiment is phase 1 of a two-phase infrared evaluation program. The system includes a vortex generator (model 320 Vortec Vortex Tube) which generates the required vortex. The mouth of the unit is mounted close to the free end of a half-inch diameter, sixteen and a half foot long stainless steel tubing (sized after tubing currently installed in the wings of an experimental Beechcraft Sundowner 180 aircraft). Dichloro difluoromethane (Freon-12) is entrained into the generated vortex. A breakdown of the vortices is indicated by the rapid diffusion and the resulting pattern is tracked using the infrared imager and video systems. Flow rates (volume and mass) are estimated at the laboratory and proposed flight conditions. The nominal flight altitude is expected to be 2500 feet.

Akinyanju, Ted↗
NASA NTRS1989

Tip vortex geometry of a hovering helicopter rotor in ground effect

The wide-field shadowgraph method has been used to photograph the tip vortices of a hovering helicopter rotor in ground effect. The shadowgraphs were used to obtain quantitative measurements of the rotor tip vortex geometry both in and out of ground effect. Many important phenomena are visible in the rotor wake using this method. These include the variation in descent and contraction rates of the tip vortices in ground effect, and the interaction between tip vortices in the far wake. The tip vortex geometry from the shadowgraphs is compared with the tip vortex geometry predicted using a free wake hover performance analysis. The free wake analysis accurately predicts the tip vortex geometry both in and out of ground effect. Performance data from the test is compared with the performance predicted using several methods, including the free wake analysis. All methods provided reasonable predictions for the helicopter performance in ground effect.

Light, Jeffrey S.↗
NASA NTRS1990

N2O as a dynamical tracer in the Arctic vortex

This paper reports N2O measurements obtained by the Airborne Tunable Laser Absorption Spectrometer from 14 flights of the NASA ER-2 aircraft during the 1989 Airborne Arctic Stratospheric Expedition field campaign. In the altitude range expected for ozone loss, N2O has a long photochemical lifetime, making it an excellent tracer of lower stratospheric air motions. As in the southern hemisphere, the zonal wind speed maximum and large gradients of potential vorticity and N2O identify the vortex edge. The N2O profiles inside the vortex indicate net descent relative to outside the vortex and to the summer polar lower stratosphere. The descent of the N2O profile during the Arctic night relative to the summer profile is comparable to the downward shift in the vertical profile observed in the 1987 Antarctic winter vortex. Winter profiles at the poles are very similar above the 435 K potential temperature surface, but divergent below.

Loewenstein, M.↗
NASA NTRS1990

Euler solutions for self-generated rotor blade-vortex interactions

A finite-difference procedure was developed, on the basis of the conservation form of the unsteady three-dimensional Euler equations, for the prediction of rotor blade-vortex interactions (BVIs). Numerical solution procedures were obtained for the analysis of the model parallel BVIs and the more realistic helicopter self-generated-rotor BVIs. It was found that, for self-generated subcritical interactions, the accuracy of the predicted leading edge pressures relied heavily on the user-specified vortex core radius and on the CAMRAD-code-predicted geometry of the interaction vortex elements and their relative orientation with respect to the blade. It was also found that the free-wake model used in CAMRAD to predict the tip vortex trajectory for use in the Euler solution yields lower streamwise and higher axial wake convective velocities than those inferred from the experimental data.

Hassan, A. A.↗
NASA NTRS1990

A numerical study of longitudinal vortex interaction with a boundary layer

A numerical study of vortex generator aerodynamics has been carried out with a reduced set of Navier-Stokes equations. These are used to model the physical process of longitudinal vortex interaction with a turbulent boundary layer on a flat plate in incompressible flow. Comparison with experimental data is used to validate the approach, and detailed predictions are made. Results show an increase in skin friction and a decrease in integral layer thicknesses where the flow is toward the wall, and the reverse where the flow is away from the wall. The major controlling parameters of vortex strength, spacing and height are each found to have optimum values for which the efficiency of boundary-layer thinning is maximized. Vortex core spreading and secondary vorticity produced in the layer are observed and studied, as well as circulation decay and other features of the flow.

Russell, D. A.↗
NASA NTRS1990

Influence of free stream turbulence on a trailing line vortex

Low-speed wind tunnel experiments have been conducted to investigate the influence of free stream turbulence on the mean behavior of a trailing line vortex. Perforated plates and screens were used to produce turbulence levels ranging between 0.03 percent and 5 percent of the free stream velocity in the vicinity of the vortex generator. Smoke was used to provide a visual image of the vortex and photographic and videotape records were taken. Experiments have shown that high turbulence levels cause vortices to meander but with little evidence of structural change. At lower turbulence intensities, some types of vortex oscillations were observed which suggest possible instabilities.

Ash, Robert L.↗
NASA NTRS1991

Flight test to determine feasibility of a proposed airborne wake vortex detection concept

This investigation was conducted to determine the radial extent at which aircraft mounted flow vanes or roll rate gyros can sense the circulatory flow field that exists around the lift induced vortex system generated by an aircraft in flight. The probe aircraft was equipped with wingtip sensors for measuring angle of attack and angle of sideslip, and with a fuselage mounted gyroscope for measuring roll rate. Analysis of flight test data indicated that the vortex was detectable at a lateral distance of about 105 feet (best results) using unsophisticated equipment. Measurements were made from the centerline of the probe aircraft to the center of the nearest vortex with the probe aircraft flying between one half and one and one half miles behind the vortex generating aircraft.

Branstetter, James R.↗
NASA NTRS1991

Computation of compressible quasi-axisymmetric slender vortex flow and breakdown

The unsteady, compressible Navier-Stokes equations are used to compute and analyze compressible quasi-axisymmetric isolated vortices. The Navier-Stokes equations are solved using an implicit, upwind, flux difference splitting finite volume scheme. The developed three dimensional solver was verified by comparing its solution profiles with those of a slender, quasi-axisymmetric vortex solver for a subsonic, quasi-axisymmetric vortex in an unbounded domain. The Navier-Stokes solver is then used to solve for a supersonic, quasi-axisymmetric vortex flow in a configured circular duct. Steady and unsteady vortex-shock interactions and breakdown were captured. The problem was also calculated using the Euler solver of the same code; the results were compared with those of the Navier-Stokes solver. The effect of the initial swirl was investigated.

Kandil, Osama A.↗
NASA NTRS1991

Guiding principles for vortex flow controls

In the practice of vortex flow controls, the most important factor is that the persistency and obstinacy of a concentrated vortex depend on its stability and dissipation. In this paper, the modern nonlinear stability theory for circulation-preserving flows is summarized, and the dissipation for general viscous flows is analyzed in terms of the evolution of total enstrophy. These analyses provide a theoretical base for understanding relevant physics of vortex flows, and lead to some guiding principles and methods for their controls. Case studies taken from various theoretical and/or experimental works of vortex controls, due to the present authors as well as others, confirm the feasibility of the recommended principles and methods.

Wu, J. Z.↗
NASA NTRS1991

Computation of steady and unsteady compressible quasi-axisymmetric vortex flow and breakdown

The unsteady, compressible Navier-Stokes equations are used to compute and analyze compressible quasi-axisymmetric isolated vortices. The Navier-Stokes equations are solved using an implicit, upwind, flux-difference splitting finite-volume scheme. The developed three-dimensional solver has been verified by comparing its solution profiles with those of a slender, quasi-axisymmetric vortex solver for a subsonic, isolated quasi-axisymmetric vortex in an unbounded domain. The Navier-Stokes solver is then used to solve for a supersonic quasi-axisymmetric vortex flow in a configured circular duct. Steady and unsteady vortex-shock interactions and breakdown have been captured. The problem has also been calculated using the Euler solver of the same code and the results are compared with those of the Navier-Stokes solver. The effect of the initial swirl has been tentatively studied.

Kandil, Osama A.↗
NASA NTRS1991

Experimental study of a vortex-shedding flowmeter

A prototype of a vortex-shedding flowmeter with no moving parts is investigated for the loading of hypergolic fuels into the Space Shuttle Orbiter. Eliminating moving parts is intended to reduce the need for servicing the meter, and the vortex shedder is compared to the turbine flowmeter presently in use. A flow test loop is designed and employed to conduct experimental investigations in which the output characteristics are examined. The relationship between vortex frequency and flow rate is almost linear, as is the relationship between vortex shedding frequency and the Reynolds and Strouhal numbers. The results are consistent with calculations and suggest that the flowmeter is a possible replacement for measuring the loading of hypergols into the Space Shuttle Orbiter.

Thinh, Ngo D.↗
NASA NTRS1991

Aerodynamics of airfoils with vortex trapped by two spanwise fences

An airfoil configuration is presented whose lift is enhanced by a trapped-vortex flow field. Based on the research to date, it is recommended that two spanwise fences be used to enclose the trapped vortex and that the fence heights be adjusted so that the equilibrium condition can be achieved with little or no mass removal from the core region of the vortex. It is also shown that the vortex bubble can be located fore and aft on the airfoil to control aerodynamic parameters, such as the pitching moment. Applications of the high-lift concept presented here are briefly discussed.

Rossow, Vernon J.↗
NASA NTRS1991

Wing tip vortex calculations with an unstructured adaptive-grid Euler solver

A solution-adaptive grid method has been developed for computing tip-vortex flowfields around rectangular wings. This method uses subdivision in order to locally refine the grid in regions with high vorticity. Two different flow solvers are used. Each solves the three-dimensional Euler equations on unstructured grids. Computed results are compared to experimentally measured surface pressures and vortex velocities on a NACA 0015 rectangular wing. Predicted results for surface pressures and integrated lift agree well with the experimental data. The predicted size of the rotational vortex core is larger than the experimentally-measured value and the peak velocities are less. This discrepancy appears to be caused by deficiencies in the inviscid Euler-equation model. This model cannot capture the complex viscous effects at the tip that determine the detailed structure of the resulting vortex. In spite of this limitation, the present Euler unstructured adaptive-grid method demonstrates the ability to convert vortical flows with low numerical diffusion. Applications for modeling helicopter rotor wake systems are discussed.

Strawn, Roger C.↗
NASA NTRS1991

Review of the physics of enhancing vortex lift by unsteady excitation

A review aimed at providing a physical understanding of the crucial mechanisms for obtaining super lift by means of unsteady excitations is presented. Particular attention is given to physical problems, including rolled-up vortex layer instability and receptivity, wave-vortex interaction and resonance, nonlinear streaming, instability of vortices behind bluff bodies and their shedding, and vortex breakdown. A general theoretical framework suitable for handling the unsteady vortex flows is introduced. It is suggested that wings with swept and sharp leading edges, equipped with devices for unsteady excitations, could yield the first breakthrough of the unsteady separation barrier and provide super lift at post-stall angle of attack.

Wu, J. Z.↗
NASA NTRS1992

Measurements of the unsteady vortex flow over a wing-body at angle of attack

Measurements of the unsteady vortex flow over a wing-body at high angles of attack were carried out on a generic test model of a pointed body of revolution with double-delta wings. Vortex patterns and trajectories were quantified from digitized laser sheet video images. The velocity-field measurements showed the jetlike flow in the unburst vortex, unsteady secondary structures below the primary core, and then the reversed flow in the burst vortex. Results of hot-film anemometry revealed the presence of peak frequencies in the velocity spectra over the wing and near the trailing edge, which varied linearly with freestream speed and increased as the measurement point moved upstream. Good Strouhal correlation was found with previous results obtained for a smaller generic wing-body model.

Debry, Benoit↗