Results for “AATT” — Page 4

NASA NTRS2020

Fiber-Optic Strain-Based Deflection and Twist Sensing for a High-Aspect-Ratio Swept Wing

Designs of aircraft structures have been moving toward leaner, lightweight designs for increased fuel efficiency. The Passive Aeroelastic Tailored (PAT) wing developed under the NASA Advanced Air Transport Technology (AATT) project is an example of a swept-wing design with high aspect ratio that incorporates lightweight highly-flexible tailored composite construction. The passive aeroelastic tailored structural design has explored the design space to enable aeroelastically tailored wing structures to increase aspect ratios (from 9 to 14) and ultimately reduce weight by 20 percent to 25 percent without impacting aeroelastic performance. To further study the aeroelastic performance of such a wing, the NASA Armstrong Flight Research Center (AFRC) (Edwards, California) has developed efficient real-time structural algorithms that are used in conjunction with a fiber-optic measurement system for lightweight vehicle applications. The AFRC Fiber Optic Sensing System (FOSS) provides up to 8,000 distributed surface strain measurements at one-half-inch increments and can be used to estimate a variety of structural parameters such as shape and load. This report discusses the implementation of strain-based displacement and twist-sensing techniques applied to the PAT wing test article tested at the NASA AFRC Flight Loads Laboratory. Empirical FOSS strain data are collected under varying loading conditions. Strain data are processed with the displacement and twist-sensing algorithms and independently verified by comparison to conventional ground-based instrumentation.

Pena, Francisco↗

NASA NTRS2019

Wind Tunnel Testing of Active Flow Control on High-Lift Common Research Model

A 10%-scale high-lift version of the Common Research Model (CRM-HL) and an Active Flow Control (AFC) version of the model equipped with a simple-hinged flap (CRM-SHLAFC) were successfully tested. The tests were performed in the 14- by 22-Foot Subsonic Tunnel (14x22) at the NASA Langley Research Center (LaRC). The CRM-HL has a set of 37° inboard and outboard single-element Fowler flaps. The CRM-SHL-AFC has a set of 50° inboard and 55° outboard simple-hinged flaps equipped with integrated modular AFC cartridges on the flap shoulder. Both high-lift configurations share the same 30° slats and engine nacelle. Three new types of AFC devices were examined: the Double-Row Sweeping Jets (DRSWJ), the Alternating Pulsed Jets (APJ), and the High Efficiency Low Power (HELP) actuators. The DRSWJ and the APJ actuators used two rows of unsteady jets, whereas the HELP actuators used a combination of unsteady and steady jets, to overcome strong adverse pressure gradients while minimizing the mass flow usage. Nozzle pressure ratio, mass flow consumption and the power coefficient, which takes account of both supply air pressure and mass flow usage for the actuators, were used for judging the performance efficiency of the AFC devices. A prestall lift performance degradation for the CRM-HL configuration was resolved with a properly placed nacelle chine. The configuration with nacelle chine was chosen as the representative reference conventional high-lift case for comparison with the CRMSHL- AFC. The AFC-induced lift coefficient increment (DCL) was maintained for the entire lift curve over the CRM-SHL-AFC case with no AFC for almost all flow-control cases examined. The lift curve of the reference CRM-HL have a slightly steeper slope compared to those of the CRM-SHL-AFC configurations. The HELP actuation concept was extremely effective in controlling flow separation in the “linear region” of the curves comparing lift coefficient to mass flow rate. The HELP actuation achieved a targeted DCL of 0.50 using a moderate amount of mass flow and supply air pressure. The CRM-SHL-AFC configuration equipped with HELP actuation was able to match or exceed the lift performance of the reference conventional high-lift configuration (i.e., CRM-HL equipped with a nacelle chine), thus meeting the NASA Advanced Air Transport Technology (AATT) project goal.

Lin, John C.↗

NASA NTRS2019

Surface Flow Visualization of the High-Lift Common Research Model

A 10% scale version of the High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The CRM-HL experiment included various configurations such as conventional and simple-hinged flaps, with and without engine nacelle/pylon, with and without nacelle chine, different Active Flow Control (AFC) methods (sweeping jets, alternating pulsed jets, and preconditioned boundary layer blowing), and their various parameters. This particular study is focused on the surface flow visualization of the conventional CRM-HL model at landing configuration. The conventional CRM-HL model with the single-slotted Fowler flap system serves as a baseline for the AFC-enabled simplified high-lift configuration as well as a high-lift technology development platform due to its publicly open geometry. Surface flow visualizations were performed using fluorescent minitufts, which were found to be nonintrusive to the aerodynamic performance. Tuft flow visualizations are supplemented with the relevant pressure and force measurements in order to understand the flow characteristics developed on the conventional CRM- HL model. In addition, three dimensional, unsteady, compressible Computational Fluid Dynamic (CFD) simulations were performed for selective cases. The surface streamlines and transverse velocity fluctuations obtained by the CFD simulations are qualitatively compared to the tuft direction and tuft unsteadiness, respectively. Force measurements of the CRM-HL model show performance degradation at higher angles of attack. Surface flow visualizations revealed the performance loss due to the nacelle/pylon wake that grows with angle of attack and eventually promotes flow separation over the inboard wing. This performance loss was successfully recovered by placing a chine on the engine nacelle.

Koklu, Mehti↗

NASA NTRSDate not supplied

TPSAS-NF1676L-32708-DND

Proposed Effort under Advanced Air Transport Technology (AATT): - Select advanced Al alloy with formability and additive manufacturability, high combined strength and toughness - Fabricate single-piece Integrally Stiffened Cylinders (~10 ft. dia. x 10 ft. long) with longitudinal stiffeners - Demonstrate joining technology for assembly of two cylinders into 20-ft. long fuselage structure - Optimize structural design incorporating tailored, selective reinforcement for durability and damage tolerance - Build-up window, door and circumferential ring frames with large-scale additive manufacturing - Structural test to validate manufacturing demonstration, structural models and analysis

Taminger, Karen M↗

NASA NTRSDate not supplied

Unsteady Pressure Measurement on a Simplified High-Lift Configuration of the Common Research Model using Active Flow Control

The High-Lift Common Research Model (CRM-HL) is a product of the NASA Advanced Air Transport Technology (AATT) Project intended to study various high-lift aerodynamic phenomena including enhanced lift, acoustic noise generation, and optimum placement of leading and trailing-edge devices. The current study was conducted in the NASA Langley 14-by 22-Foot Subsonic Tunnel (14x22) for the purpose of evaluating enhanced lift through the use of active flow control (AFC). The current paper documents the effect of sweeping-jet actuation combined with steady blowing on a simplified high-lift configuration using unsteady pressure measurements. The time-series parameters for the measurements are documented as well as the data acquisition system used to acquire the data. An uncertainty analysis will be presented in order to document the system performance and provide an estimate of the data quality. Repeatability of the data will be shown along with trends associated with model angle of attack, and those associated with changes in the nozzle pressure ratio (NPR) of the AFC system.

Common Research Model↗

NASA NTRSDate not supplied

Permanent Magnetic Synchronous Motor (PMSM) Model Development

The Advanced Air Transport Technology (AATT) Project seeks to enhance the capabilities of fixed-wing subsonic transport through improved energy efficiency and environmental compatibility. One element of this effort is the use of high efficiency PMSM systems. Understanding the behavior and limitations of the se motors allows the National Aeronautics and Space Administration (NASA) to collaborate with and inform its partners worldwide. PMSM modeling is achieved using MATLAB®-Simulink® (The Math Works, Inc., Natick, Massachusetts). Through the analysis of an existing high-fidelity NASA Electrical Aircraft Testbed (NEAT) model, simplified models of varying fidelity can be developed with the goal of building a PMSM model capable of running in real-time for use in a piloted simulation environment. By utilizing system identification methods, it has been demonstrated that internal electrical components like the inverter can be represented by a simple variable gain thus greatly reducing the required simulation step size and subsequently decreasing model run-time by multiple orders of magnitude

motor controls↗

NASA NTRSDate not supplied

Unsteady Pressure Measurements on a Simplified High-Lift Configuration of the Common Research Model using Active Flow Control

The High-Lift Common Research Model (CRM-HL) is a product of the NASA Advanced Air Transport Technology (AATT) Project intended to study various high-lift aerodynamic phenomena including enhanced lift, acoustic noise generation, and optimum placement of leading and trailing-edge devices. The current study was conducted in the NASA Langley 14-by 22-Foot Subsonic Tunnel (14x22) for the purpose of evaluating enhanced lift through the use of active flow control (AFC). The current paper documents the effect of sweeping-jet actuation combined with steady blowing on a simplified high-lift configuration using unsteady pressure measurements. The time-series parameters for the measurements are documented as well as the data acquisition system used to acquire the data. An uncertainty analysis will be presented in order to document the system performance and provide an estimate of the data quality. Repeatability of the data will be shown along with trends associated with model angle of attack, and also those associated with changes in the nozzle pressure ratio (NPR) of the AFC system.

Active Flow Control↗

NASA NTRSDate not supplied

Update on ScreenVane Testing in W8

Summary of on-going work on the NASA AATT Boundary Layer Ingesting Tailcone System (BLITS) work. Includes a summary of the overall project as well as recent work on ScreenVane development and facility upgrades to test the BLI2DTF in the GRC W8 Facility

BLI↗

NASA NTRS2022

Low-Speed Performance Enhancement Using Localized Active Flow Control: Localized Active Flow Control Simulations on a Reference Aircraft (2/4)

A study of the potential implementations of localized active flow control (AFC) technology onto future airplanes is presented. This collaborative investigation addresses key objectives of the NASA Advanced Air Transport Technology (AATT) Project, in terms of reduction in fuel consumption and lower emission. It specifically targets the goals set forth in a roadmap developed by the NASA/Boeing team. The roadmap is a result of a series of meetings held between the two parties over the years and it represents a shared vision for practical implementations, leading up to flight demonstrations of localized flow control. If successful, localized flow control may lead to important ramifications for next generation airplanes from both the economic and environmental perspectives. Under this contract localized AFC has been used to improve aerodynamic performance during high-lift operations using Computational Fluid Dynamics (CFD). Specifically, AFC has been applied at the aileron and at various location in the wing leading edge (LE) regions. The applications target reduced drag and enhanced lift over the range of practical angles of attack, including stall. These benefits translate to airplane performance improvements, such as longer range or larger payload. The CFD results are used to quantify potential aerodynamic benefits, as well as the input required for actuation. This helps identify the most promising candidates, which potentially provide material net airplane level enhancements using onboard fluidic sources. The airplane configuration selected for the CFD study is a representative of a future short/medium-range twin-engine airplane dubbed the Reference Aircraft. A slew of AFC applications has been explored and their aerodynamic performance enhancements were benchmarked against the baseline Reference Aircraft. Promising AFC candidates have been deemed practical and potentially suitable for both the aileron and the wing LE implementations. The findings on the Reference Aircraft are used to guide the development of the AFC-enhanced aileron for the CRM-HL. The wind-tunnel model of the CRM-HL will be used by NASA to validate the AFC concepts, complementing the CFD-based analysis and the integration study (final report document #3).

CFD↗

NASA NTRSDate not supplied

Power and Propulsion: Small Core Advanced Thermal Management Project Overview

This presentation is intended to provide an overview of the various efforts under the Advanced Air Transport Technology (AATT) project related to engine thermal management. Sustainable flight is the key motivator for all our efforts, and innovative thermal technologies play a crucial role in achieving this goal. The technologies described in this presentation can be applied to both traditional gas turbines and advanced cycles which utilize alternative fuels. Within our project, we utilize the capabilities of artificial intelligence (AI), machine learning (ML), and additive manufacturing. This ranges from using AI to generate heat exchanger fin topologies, to using ML for a reduction in computational cost which allows for a more thorough design exploration. Many times, the resulting topologies can only be realized through additive manufacturing techniques. Most of what’s presented is currently low TRL, but the intent is to achieve TRL 4 by the end of the project.

Propulsion↗

NASA NTRSDate not supplied

High Fidelity Adaptively Refined CFD and Reduced Order Models of a High Aspect Ratio Aeroelastic Wing Wind-Tunnel Model

The NASA Advanced Air Transport Technology (AATT) goal of reduced fuel burn for transport aircraft has led to the NASA N+3 High Aspect Ratio Wing (HARW) subproject. This project requires identifying, developing, and demonstrating key technologies and integrated multidisciplinary solutions to enable a safe, high performance, aeroelastic wing. Since this aircraft will have a high aspect ratio wing, aeroelasticity is expected to be a major issue in the design. In this paper high fidelity computational fluid dynamics (CFD) is performed with flow adapted meshes. A system identification of the aerodynamics is developed using both a multi-modal multi-sine time-marching and a multi-mode linear frequency domain method. GLA, MLA and flutter suppression simulations will be performed.

Robert Bartels↗

NASA NTRSDate not supplied

Simplified Applied Loads of a Transonic Truss-Braced Wing Derived from Computational Fluid Dynamics

The transonic truss-braced wing (TTBW) concept is under consideration by the NASA Advanced Air Transport Technology (AATT) project due to its potential to reduce fuel consumption of transport aircraft. To properly evaluate the TTBW concept, detailed structural modeling and subsequent test planning is underway, which requires a simplified set of discrete applied loads that simulate the distributed aerodynamic pressures. Given the unique architecture of the TTBW and its intended operation in the transonic regime, computational fluid dynamics (CFD) is the ideal approach to employ to ensure the aerodynamics of this configuration are sufficiently captured. To convert aerodynamic results into input for structural models, application of a data transfer tool, Discrete Data Transfer Between Dissimilar Meshes (DDTBDM), is presented to resolve aerodynamic pressures from CFD into single load vectors at hardpoints along both the wing and the strut. Evaluation of mapping the aerodynamic forces to hardpoints at rib and spar intersections in a structural model is performed, and the results are also compared with a linear static aeroelastic analysis. The structural responses indicate that distributing forces along only the wing and strut forward spars is insufficient for simulating the distributed aerodynamic loads. Adding moments along the forward spars improved the global response of the wing, but the point moments created unrealistic local rotations within the structure. When distributing loads along both the forward and aft spars of the wing and strut, the global response was less sensitive to the inclusion of point moments, which indicated the arrangement of point forces alone was sufficient input for structural design work and testing and provided a more continuous loading profile.

Finite Element↗

NASA NTRSDate not supplied

Simplified Applied Loads of a Transonic Truss-Braced Wing Derived from Computational Fluid Dynamic

The transonic truss-braced wing (TTBW) concept is under consideration by the NASA Advanced Air Transport Technology (AATT) project due to its potential to reduce fuel consumption of transport aircraft. To properly evaluate the TTBW concept, detailed structural modeling and subsequent test planning is underway, which requires a simplified set of discrete applied loads that simulate the distributed aerodynamic pressures. Given the unique architecture of the TTBW and its intended operation in the transonic regime, computational fluid dynamics (CFD) is the ideal approach to employ to ensure the aerodynamics of this configuration are sufficiently captured. To convert aerodynamic results into input for structural models, application of a data transfer tool, Discrete Data Transfer Between Dissimilar Meshes (DDTBDM), is presented to resolve aerodynamic pressures from CFD into single load vectors at hardpoints along both the wing and the strut. Evaluation of mapping the aerodynamic forces to hardpoints at rib and spar intersections in a structural model is performed, and the results are also compared with a linear static aeroelastic analysis. The structural responses indicate that distributing forces along only the wing and strut forward spars is insufficient for simulating the distributed aerodynamic loads. Adding moments along the forward spars improved the global response of the wing, but the point moments created unrealistic local rotations within the structure. When distributing loads along both the forward and aft spars of the wing and strut, the global response was less sensitive to the inclusion of point moments, which indicated the arrangement of point forces alone was sufficient input for structural design work and testing and provided a more continuous loading profile.

Finite Element↗

NASA NTRSDate not supplied

ISAAC Integrated Structural Assembly of Advanced Composites

The NASA Langley Research Center obtained the Integrated Structural Assembly of Advanced Composites (ISAAC) robotic system in 2014 to add state-of-the-art automated manufacturing of composites to our traditional in-house design, analysis, and experimentation capabilities. ISAAC is used to explore fabrication of parts with novel designs and for research into new composite manufacturing techniques. Automated fiber placement (AFP) was the initial manufacturing capability on ISAAC and has been used to support a range of aeronautics and space projects including the Advanced Composites Project (ACP), Composites for Exploration Upper Stage (CEUS), and Advanced Air Transportation Technologies (AATT). In addition to AFP, ISAAC can now provide through-thickness reinforcement of composites by adding stitches through dry fabric prior to resin infusion. Stitching is of interest since it can improve damage tolerance, reduce final assembly time, and reduce inspection requirements. ISSAC can stitch traditional single-needle seams and perform stitching operations using two needles when access is only available to one side of the part. Stitching capability is being advanced in the High-Rate Composites Aircraft Manufacturing (HiCAM) project today. This lecture will describe the work with ISAAC today and new exciting plans for the future.

automated fiber placement↗

NASA NTRSDate not supplied

NASA’s Efficient Quiet Integrated Propulsors (Equip) Technical Challenge

Advances in aircraft propulsor technology - ducted and unducted - are key elements to developing a sustainable aviation future. Increasing propulsive efficiency comes with significant challenges. The long-term trend in aircraft engine design has been towards higher bypass ratios to increase efficiency and decrease noise. Current designs are pushing against limits on engine size; the engine must fit under the wing and overcome the nacelle weight, aerodynamic drag, and airframe integration penalties associated with an ultra-high bypass ratio. The next-generation ducted engines will have shorter inlets and smaller rotor-stator spacing to minimize nacelle area. This increases the potential for non-uniform flow at the fan face and less area for acoustic liners. Unducted engines eliminate the nacelle penalty while presenting challenges to noise and operability in distorted flow environments. The overall diameter in both cases raises questions about engine-airframe integration to maximize efficiency gains and minimize installation penalties. The National Aeronautics and Space Administration (NASA) Advanced Air Vehicles Program (AAVP) approved the Efficient Quiet Integrated Propulsor (EQuIP) Technical Challenge (TC) under the Advanced Air Transport Technology (AATT) Project to work on next-generation propulsor technologies in collaboration with NASA’s government and industry partners in the Sustainable Flight National Partnership. The EQuIP TC leverages NASA resources with Federal Aviation Administration (FAA) and industry investments under the FAA’s Continuous Lower Energy Emissions and Noise (CLEEN) program to address technical challenges on the propulsor subject to the flow field imposed by the engine-airframe-flight environment. The EQuIP TC complements NASA Aeronautics Research Mission Directorate’s (ARMD) existing investments in sustainable aviation for the next-generation of commercial aircraft and contributes to meeting the noise and efficiency goals set by the Sustainable Flight National Partnership and U.S. Aviation Climate Action Plan. This paper introduces the EQuIP TC, describes key parts of its development, and presents the background research used to scope its impact.

Propulsion↗

NASA NTRSDate not supplied

Testing of High-Lift Common Research Model at Takeoff Configurations

The 10% scale High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The main objective of the wind tunnel test was to improve the aerodynamic performance of a representative aircraft model during takeoff operations using localized active flow control (AFC). This approach involves the application of AFC concepts locally to a relatively small region; therefore, it has the potential to cause minimal architectural change to current aircraft configurations. In addition, the power requirements of localized AFC could be supplied with onboard air resources. Recent exploratory studies identified the aileron as a target area for improving lift-to-drag ratio using localized AFC concepts. The idea is to deflect the ailerons beyond their nominal deflection angles and use AFC to reduce flow separation that occurs at larger aileron deflections. Several AFC concepts with different configurations were evaluated with the goal of achieving high-lift performance improvement. The assessment of AFC configurations is reported in a companion paper. The focus of the current paper is to report the data relevant to the CRM-HL takeoff configurations and establish a reference case for localized AFC application. Three takeoff configurations —reference, nominal, and high-lift improved—are documented. These takeoff configurations are obtained by varying aileron deflection. Wind tunnel measurements including surface static pressures and force and moment data are presented. In addition, surface tuft flow visualization, mainly on the aileron, is provided to understand the flow characteristics developed over the aileron during takeoff.

Lift-to-Drag↗

NASA NTRSDate not supplied

Active Flow Control Enhanced Aileron of the High-Lift Common Research Model at Takeoff Condition

An experimental investigation was conducted in the NASA Langley 14- by 22-Foot Subsonic Tunnel on the NASA 10% scale High-Lift Common Research Model (CRM-HL) to improve the high-lift aerodynamic performance of the takeoff configuration. Active flow control (AFC) was applied at the aileron hinge line to control flow separation at high aileron deflection angles ( δ a ) to increase lift-to-drag ratio (R/J). Improvements in low speed R/J can increase vehicle payload and/or range resulting in a more efficient vehicle. Aileron deflection angles of 0°, 7.5°, 16°, and 25° were investigated. Flow control was applied to the two largest aileron deflections, which are considered the high-lift (HL) improved takeoff configurations. A companion paper will discuss baseline flow characteristics of the CRM-HL at the three takeoff conditions: reference, nominal, and HL-improved. In this paper, we focus on the aerodynamic improvement obtained when AFC was applied to δ a = 16° relative to the nominal configuration, δ a = 7.5°. Multiple flow control parameters, including actuator type, spacing, and intensity, were investigated to evaluate the efficiency of the actuation system. The different AFC configurations tested were assessed with tuft visualization, steady surface pressure data, and force and moment data. The results indicated that all actuation types and spacings examined led to an increase in lift across the range of angles of attack investigated. Flow separation was mitigated with the injection of momentum at the aileron hinge line. The configurations with the smallest spacing produced the highest improvement in L/D . Steady jet actuation showed higher efficiency but similar aerodynamic performance when compared to the sweeping jet actuators. This work was performed in support of the NASA Advanced Air Transport Technology (AATT) Project.

High-Lift Common Research Model↗

NASA NTRSDate not supplied

Testing of High-Lift Common Research Model at Takeoff Configurations

The 10% scale High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The main objective of the wind tunnel test was to improve the aerodynamic performance of a representative aircraft model during takeoff operations using localized active flow control (AFC). This approach involves the application of AFC concepts locally to a relatively small region; therefore, it has the potential to cause minimal architectural change to current aircraft configurations. In addition, the power requirements of localized AFC could be supplied with onboard air resources. Recent exploratory studies identified the aileron as a target area for improving lift-to-drag ratio using localized AFC concepts. The idea is to deflect the ailerons beyond their nominal deflection angles and use AFC to reduce flow separation that occurs at larger aileron deflections. Several AFC concepts with different configurations were evaluated with the goal of achieving high-lift performance improvement. The assessment of AFC configurations is reported in a companion paper. The focus of the current paper is to report the data relevant to the CRM-HL takeoff configurations and establish a reference case for localized AFC application. Three takeoff configurations —reference, nominal, and high-lift improved—are documented. These takeoff configurations are obtained by varying aileron deflection. Wind tunnel measurements including surface static pressures and force and moment data are presented. In addition, surface tuft flow visualization, mainly on the aileron, is provided to understand the flow characteristics developed over the aileron during takeoff.

Wind tunnel test↗