Search NASA⌕ Search

SEARCH · Search NASA

Results for “ACCIDENT CAUSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

SATS Transient Fission Gas Release Test with Irradiated Fuel under Loss of Coolant Accident Conditions

The transient fission gas release (tFGR) during the temperature ramp associated with a loss-of-coolant accident (LOCA) in light-water reactors (LWRs) is likely a significant contribution to the total pressure in a fuel rod and may cause an unexpected rod burst. The lack of data related to tFGR continues to be a key gap in understanding LWR cladding burst behavior under LOCA conditions. To fully characterize this behavior, tFGR data must be collected from several different systems that can capture all relevant testing conditions. Oak Ridge National Laboratory (ORNL) has developed a system to measure the integral tFGR from irradiated fuel segments. This system was designed to integrate with the existing Severe Accident Test Station (SATS) and to build upon decades of experience capturing fission gas to characterize fuel behavior. The tFGR system consists of a sweep gas system to transport gases from the in-cell SATS apparatus to an out-of-cell fission gas detection system composed of a series of cold traps to capture the off-gas from the heating tests and a gamma spectrometry system to detect and measure 85 Kr. Initial system testing operations were completed during which 85 Kr collection and measurement were verified along with the ability to detect stable inert gases. A tFGR test with a high-burnup fuel specimen was successfully conducted by the in-cell SATS-tFGR system at ORNL. The posttest examination is under way, the result of which will be reported in FY24.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Improving Dose Modeling With Dynamic Modeling Tools [Slides]

Utilities aiming for higher fuel enrichment for power uprates or extended operation times before refueling must conduct a new dose analysis. Current conservative dose estimation standards may cause utilities to exceed regulatory limits for proposed increased fuel enrichment. A more accurate modeling of doses from reactor accidents can lower these conservative assumptions. Prescott et al. (2022) demonstrated that the Event Modeling Risk Assessment using Linked Diagrams (EMRALD) software tool, developed at Idaho National Laboratory (INL), can be coupled with the Modular Accident Analysis Program (MAAP5) for dynamic accident analysis in reactor plants. EMRALD forms models of potential accident scenarios, while MAAP5 simulates the accident progression and dose consequences. By integrating these software tools with utility-specific data, a more precise estimation of dose consequences from plant accidents can be achieved. Preliminary findings indicate that EMRALD provides accurate mean core damage frequencies for generalized accident scenarios. Future work includes expanding the model to account for plant-specific data and mitigation factors.

97 - MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Crush Gun Impact of Lightly Confined Explosive with Rounded Projectiles at Nominal Velocity 35 m/s

Blunt, crushing impact of high explosives can cause internal shear heating sufficient to ignite a deflagration. Low-velocity impact of this sort is plausible in handling accident scenarios, e.g. if a charge is dropped or an object is dropped onto a charge. This mechanism can also be activated during sub-shock fragment impact. Efforts to model this viscous shear heating mechanism are currently being developed and refined. The Crush Gun apparatus was created to provide a controlled low-velocity impact stimuli to explosive samples. Infrared thermography captures temporal- and spatially-resolved heating that occurs during the impact event.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2022

Synthetic Sling Failure: Evaluations and Recommendations

The information and evaluations provided in this report were compiled to address the recurring problem of synthetic sling failure. As safety is the number one priority in all work aspects, a solution must be devised to prevent accidents from occurring. In revision 0, a total of thirteen cases regarding synthetic sling failure were evaluated in order to determine their causes, effects, and preventative measures. From the collected data, it was found that all cases in which the synthetic sling contacted the edge of its load resulted in sling failure. Revision 1 provides updated synthetic fling failures between the years of 2009 revision 0 and 2021 revision 1.

42 ENGINEERING↗
DOE OSTI2020

Determining Compression Characteristics of Honeycomb Material - 19674

The objective is to determine compression test characteristics of stainless steel honeycomb material to be able to represent honeycomb structures accurately in analytical models used to simulate hypothetical accident scenarios of shipping packages. Honeycomb is a material used primary in the aerospace industry due to its high strength-to-weight ratio. Because it doesn't have a shelf life and can withstand high heats, it is an excellent candidate for a structural material in package designs. Honeycomb has orthotropic material properties. The honeycomb currently being evaluated is made of metal ribbons spot welded together to form hexagon pattern between metal plates. The hexagon ribbons are brazed to the metal plates. The complexity of the honeycomb significantly lengthens the simulation time, which is further complicated when the brazing, welding, and imperfections of the material is considered. This means to affectively represent the honeycomb in simulation programs, such as Abaqus, the material needs to be approximated as a uniform orthotropic material. This requires material properties in each of the three directions, T, W, and L. The T direction is defined as the 'strong' direction, perpendicular to the honeycomb sheet. The L direction is parallel the ribbon and the W direction is perpendicular to the ribbon. Honeycomb has 3 different compression stages. Stage 1 is the initial compression where the honeycomb maintains its structural integrity and does not permanently deform from loads from normal operations. Stage 2 is when the initial buckling causes irreversible damage to the honeycomb. Stage 2 is the one we are most interested in because it absorbs the most energy from a hypothetical accident scenario. During Stage 2, the honeycomb fails layer-by-layer, indicating that the more layers, the longer material crushing is sustained, and thus the more energy that is absorbed. Stage 3 is final compression, similar to compressing solid metal. During stage 3 the stress increases with a diminishing rate of elongation and the honeycomb is completely failed where the plates between the honeycomb core sandwich the crushed honeycomb ribbon. The stress-strain graph bellow shows compression test of 3 different samples in the T direction. The red lines divide the three stages. The far left is Stage 1, the middle stage 2, and the right stage 3. The data collected is displayed in the table below. The expressions in the table represent the regression formula that represents each stage of the compression on a stress-strain graph. Stage 1 is assumed to intersect with the origin; data for stage 3 for the crush in W and L directions where unable to be gathered due to the nature of failure for those directions. Stage 1 and 2 are linear regressions while stage 3 is a degree 2, to best match the curve. Linear regression is used on stage 2 because ultimately that represents the energy absorbed. With more data, a degree n x 2 regression would be a more appropriate regression for stage 2, where n is the number of layers. The table below is the approximation of each scenario and stage. Each stage starts and ends at the intersection of the next stage. There where two main objectives for these tests: firstly to understand how honeycomb performs under extreme compression, and secondly to be able to numerically represent the honeycomb structure. Both of these where completed to varying degrees. It is important understood how the honeycomb fails. If it is crushed in the T direction it retains its integrity even after being crushed, however when crushed in the L and W crush direction, if it fails, it disintegrates, and loses all integrity. Also, the more layers the more time the material spends in stage 2. Failure is started by buckling, thus if there is any imperfection, the stress will not spike but transition straight into stage 2. The data collected and aggregated can be used for initial simulation of honeycomb used in packages. The initial testing has set the ground work for more data to be collected in order to verify results and to allow more confidence in the simulation results. This is only the initial data collected. The next steps is to continue to collect more data to verify results and to test more variants of honeycomb, with different brazing, layers, and shape.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Temperature sensitivity of the equilibrium neutronics and accident analysis of the HTR-10

Pebble-Bed High-Temperature Gas-cooled Reactors (PB-HTGR) are moderated by the graphite in the fuel pebbles and the graphite reflector surrounding the pebble-bed. Because graphite is by far the most abundant material in PB-HTGRs and the primary moderator, accurate modeling of the graphite material, including density, impurities, and temperatures, is crucial for accurate computational modeling and simulation of these reactors. While main characteristics of the graphite components are often known, the local temperature is less well known and often averaged over all components. Here, this work studies the impact of considering accurate temperature profiles in the graphite material on the generation of a small PB-HTGR model at the state of equilibrium operation and on short-term accident progression. The fuel compositions for the PB-HTGR were determined using a jump-in equilibrium modeling method, the Axial Radial Zone Equilibrium Modeling (AR-ZEM) method. In contrast to previous work, the AR-ZEM method was used considering thermal-hydraulic feedback from the MELCOR code to determine temperatures of the fuel pebbles and the surrounding graphite reflector. The consideration of an axial and radial temperature profile in the core and reflector, as opposed to uniform material temperatures, had an impact of almost 1,300 pcm on the equilibrium core eigenvalue and caused significant differences in the discharged plutonium fuel inventory with up to 4.9% and 11.0% for Pu-239 and Pu-242, respectively. To assess the impact on short-term accident progression, two Anticipated Transient Without SCRAM (ATWS) events, a Pressurized Loss of Forced Coolant (PLOFC) and a Control Rod Withdrawal (CRW) with loss of flow, were simulated with MELCOR. The use of temperature profiles in the equilibrium core models did not reveal a significant impact on the temperature, power, or reactivity responses during the transients. In conclusion, a need for consideration of accurate temperature profiles, in particular for the graphite reflector, was found for the generation of equilibrium PB-HTGRs core models using jump-in methods, but detailed temperature profiles may not be necessary when performing conservative transient analysis.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

BISON validation of FeCrAl cladding mechanical failure during simulated reactivity-initiated accident conditions*

Here, a reactivity-initiated accident (RIA) is a postulated design basis accident in light water reactors (LWRs) in which a rapid reactivity insertion induces a fission rate increase and a fuel pellet temperature rise. During RIA, the fuel pellet thermally expands and may cause pellet-cladding mechanical interaction (PCMI). Separate effects PCMI tests were performed on C26M FeCrAl cladding tube samples, introducing biaxial stress via a well understood modified burst test (MBT) system. A high-speed camera in the MBT system captured the projections, covering a 360° view of the cladding deformation and enabling a digital image correlation (DIC) method to quantify the surface strains with high fidelity. Representative hot zero-power RIA mechanical loading conditions were applied to the sample, and the test duration ranged from 20 to 500 ms at an average temperature of 573 K. BISON finite element–based fuel performance code modeling was performed against the high-fidelity DIC data produced from the MBTs. Validation calculations were conducted with 2D models and systematically compared with test data of the burst time, burst pressure, burst hoop strains, and hoop strain rates. Based on the behaviors from the separate effects test, BISON calculations satisfactorily predicted the cladding deformation behaviors. Sensitivity analysis was conducted to identify highly influential mechanical properties responsible for the cladding failure behavior during the MBT experiments. The results highlight the significance of the cladding's mechanical strength in governing cladding strain, followed by the significance of the mechanical interactions between the pellet and the cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Characterization of Surrogate Molten Salt Reactor Aerosol Streams

Measuring the aerosol evolution from MSRs is important for monitoring the off-gas system of the reactor and is particularly important for detecting off-normal conditions. In a molten salt reactor (MSR) accident scenario, an aerosol release would be a major factor in the source term. This aerosol stream would likely be generated from a breach in the cover gas system, which causes particles produced from fission itself to escape, or from a salt spill that produces aerosols through splashing and secondary reactions. The particle size of the produced aerosols is anticipated to vary greatly and range from 0.01 to 10 µm. The transport of these aerosols would be dependent on the particle size. A better understanding of aerosol generation, size, and monitoring methods are needed to inform estimation and mitigation of potential aerosolized source terms from MSRs. While salt spill experiments are being performed at Argonne National Laboratory, the development of aerosol characterization and monitoring methods are being developed at Oak Ridge National Laboratory. To generate prototypic aerosols for use in testing monitoring instruments and mitigation methods, a surrogate aerosol stream was produced with a Collison nebulizer, and the particle size distributions were measured with a cascade impactor. The results demonstrated that by changing the nebulizer pressure, the aerosol particle size distribution can be adjusted to best match the region of interest for experiments with higher pressures, driving the particle size down. However, nearly all aerosols formed exceeded 1 µm in diameter, providing a lower bound for the surrogate aerosol stream. In addition to verifying the applicability of this surrogate aerosol stream, this work has shown that a laser induced breakdown spectroscopy monitoring system that is under development is resilient to changes in particle sizes, increasing its robustness for off-gas monitoring.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2026

Cluster Dynamics Simulations of Intra-Granular Fission Gas Bubble Size and Pressure Evolution in UO 2

Fission gases such as xenon (Xe) play a critical role in determining the behavior and response of nuclear fuel. Given that Xe has little solubility in UO 2 , it accumulates and forms bubbles, which significantly impact fuel performance. Intra- and inter-granular bubble nucleation and growth can lead to fuel swelling, and once bubbles interconnect at grain boundaries, fission gas can be released into the plenum. At low temperatures, limited uranium vacancy mobility can restrict swelling, therefore causing the bubbles to become highly pressurized. Consequently, this can induce micro-cracking, promote fission gas release (increasing the likelihood of cladding failure), and even lead to fuel pulverization under accident conditions such as a loss of coolant accident. As bubble evolution is strongly influenced by local temperature and fission rate, markedly different behavior occurs across the radial profile of the fuel pellet. Capturing the mechanisms that underpin bubble evolution is therefore important to predict these behaviors in the fuel. Previous models describing important mechanisms informed by lower length scale simulations have been developed under the NEAMS program. These can describe the evolution of a single bubble type (i.e., single value for radius and pressure) at each position in the pellet, for instance using the Centipede cluster dynamic code. However, in reality, a full distribution in bubble sizes and pressures exists within the microstructure at a given position in the pellet. To address this the cluster dynamics code Xolotl, which can predict Xe and vacancy phase space (i.e., bubble distributions) for intra-granular bubbles, has been used before. Prior work benchmarked the Xolotl code against the Centipede cluster dynamics code to ensure compatibility and to verify that mobile defect properties are adequately transferred between the two codes, along with some physics improvements. In this work, we go further by introducing a physics-based set of improvements that will allow us to accurately predict bubble size distributions and internal bubble pressures under representative UO 2 irradiation conditions. The improvements include (i) coupling bubble-defect reaction energies to a virial equation of state (EOS), (ii) including a bubble surface tension contribution, (iii) incorporating radiation-induced re-solution of Xe and vacancies, (iv) enabling pressure-driven dislocation loop punching through an effective emission of interstitial clusters informed by interstitial loop energetics, (v) accounting for radiation induced athermal diffusion of Xe, and (vi) implementing a Booth-type grain boundary sink representation for all mobile defects and defect clusters. After these modifications, we observe good agreement of Xolotl fission gas bubble size and concentration predictions with legacy experimental measurements. Additionally, it allows the distribution of Xe bubble pressures and radius to also be predicted and compared to data produced through the Advanced Fuels Campaign (AFC) program. Here, we have done this by running simulations under conditions similar to the AFC post-irradiation examination (PIE) samples irradiated at North Anna 2 light water reactor (LWR). Our results shows excellent agreement with these experimental measurements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Dynamic P-Q Capability and Abnormal Operation Analysis of a Wind Turbine with Doubly-Fed Induction Generator

After several accidents occurred in wind farms in the United States and around the world, the subsynchronous oscillation (SSO) issues in grid-connected wind farms have gained serious attention. Particularly, these issues have caused significant challenges to wind turbines with a doubly fed induction generator (DFIG) because it is connected to the grid via both its stator and rotor paths. Traditionally, a P-Q capability chart is utilized to assure the safe operation boundary for a synchronous generator. But the energy conversion characteristics of a DFIG wind turbine are completely different. A critical factor to affect the reliable operation of a DFIG wind turbine is the rated current and pulse-width modulation (PWM) saturation constraints of its power converters. These constraint conditions can be affected by the wind turbine rotating speed and grid conditions. However, a detailed study of DFIG P-Q capability from these perspectives has not been conducted, which has hindered adequate understanding of many abnormal wind turbine operations reported in the literature and the development of advanced control technologies to overcome the challenges. The proposed study in this paper considers vector control implementation to DFIG power electronic converters in the dq reference frame, and the models and algorithms developed for the P-Q capability study have addressed specific DFIG power converter constraints that are different from those of a traditional synchronous generator. The paper especially focuses on exploring the dynamic natures of DFIG P-Q capability under uncertain and variable conditions to explore the root causes of many abnormal operations of DFIG wind turbines reported in the literature. The proposed study is validated through an electromagnetic transient simulation model of a grid-connected DFIG wind turbine. The proposed study has the potential to lead to the development of new DFIG control technologies that can help overcome the challenges for many abnormal operations of DFIG wind turbines.

17 WIND ENERGY↗
DOE OSTI2024

Safety Basis Compliant Flexible Operations [Capstone Project]

Compliant nuclear operations must be weighed against the radiological risk to the worker, public, and the environment. This project set out to look at one facility at Los Alamos National Laboratory (LANL or the Laboratory) and compare the risk with the operational restrictions associated with the Technical Safety Requirements (TSRs). The hope was to identify controls that could be reduced or simplified while maintaining compliance with 10 CFR 830, Nuclear Safety Management. This would result in increasing facility operational flexibility and efficiency. Controls were identified to be simplified or eliminated based on risk. This identification was initially envisioned from the perspective of reanalysis of the accident and hazard analysis consequences. Additionally, it was envisioned that fire testing could show that the consequences of a fire are not as dramatic as analyzed. Specific facility controls were identified that cause operational inefficiencies. Based on data collection, two controls were identified for further evaluation. The first control was combustible loading within the waste storage buildings, and the second control is related to the seismic power cutoff switch. In evaluating the combustible loading control, the thought is that the fire suppression system (FSS) provides adequate protection and the combustible loading controls do not need elevation to a TSR control. The FSS, along with the Fire Protection Program, would provide protection to prevent a fire from impacting large amounts of stored waste material. The seismic switch was more of a challenge. When reviewing the facility operation, it was determined that the facility does not operate anywhere near the established material-at-risk (MAR – radioactive material) limits. By adjusting these limits, a reduced consequence could be achieved and hence, a significant risk reduction achieved. A new operating mode would be used to achieve this reduction. A reduced MAR limit was successfully used as a test case for snow removal during this project. This project expands on that trial case as related to combustible loading and the seismic power cutoff switch TSRs. This will increase the efficiency of operations with reduced TSR controls while reducing overall facility risk. This is a win-win situation for Triad National Security, LLC (Triad) and the U.S. Department of Energy (DOE). Due to schedule and budgetary constraints, not all envisioned work scope was accomplished. However, it is maintained in this report for future efforts.

61 RADIATION PROTECTION AND DOSIMETRY↗
DOE OSTI2024

Mechanical degradation of duplex SiC-fiber reinforced SiC matrix composite tubes under a controlled high-temperature steam environment

This paper describes results from the mechanical evaluation of unirradiated SiC fiber–reinforced SiC matrix composite tubes under a controlled high-temperature steam environment. The experiments were aimed at identifying key material degradation behavior under environments relevant to loss-of-coolant accidents of light water reactors. Mechanical tests of the SiC composite tubes at 1000 °C under steam and inert environments were conducted using a unique test capability. Further, the material tested was a duplex tube with a thick monolithic SiC layer on the outer surface. The tubes were subjected to preloading at ~100 MPa in tension before exposure to high-temperature steam with up to 75% of the preload at a constant displacement. In the presence of matrix cracks, the steam exposure caused embrittlement of the SiC composite tubes and failure at a stress level below the pretest stress. The material degradation was explained by a fiber oxidation model, which can be applied to various SiC cladding concepts. The embrittlement could be a limiting factor for using SiC cladding subjected to loss-of-coolant accident conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Demonstration and Verification of Thermo-Mechanical Bowing in a Limited Free-Bow SFR Concept Using MOOSE

Core bowing due to thermal gradients and irradiation induced swelling and creep introduces significant reactivity feedback effects in liquid metal-cooled fast spectrum reactors. During startup, normal operations, and transient events, differential thermal and flux gradients cause expansion, creep, and swelling, which results in bowing in preferential directions depending on local material properties and load-pad and restraint-ring design. The bowing phenomenon produces negative reactivity during accident conditions provided the restraint system has been properly designed to optimally guide the deformation outwards in the active core region. Under the Department of Energy Nuclear Energy Advanced Modeling and Simulation program, a Multiphysics Object Oriented Simulation Environment (MOOSE)-based multiphysics approach to model core bowing is being developed. The present work expands on previous modeling of simpler International Atomic Energy Agency (IAEA) verification problems with these tools by modeling IAEA Verification Problem 4, which involves a symmetric sector of a reactor core with ducted assemblies undergoing differential thermal expansion due to thermal gradients bowing outward with duct-to-duct contact. This model is available on the National Reactor Innovation Center Virtual Test Bed repository. This example was verified against benchmark participant results, which includes bowing deformation evaluation and duct-to-duct interactions at load pads with mechanical contact.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this paper are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

Accident Tolerant Fuels↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this presentation are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

3D probabilistic fracture mechanics / computational fluid dynamics simulation of a reactor pressure vessel under transient conditions

Reactor pressure vessels (RPVs) are safety-critical light-water-reactor components that, under irradiation, experience long-term material degradation in the form of embrittlement. This can increase their susceptibility to fracture under thermal-shock conditions, which could occur during off-normal transients such as loss-of-coolant accidents (LOCAs). During a LOCA, the most severe conditions for the RPV occur when emergency core cooling water is injected through the cold legs into the water-and-steam-filled RPV. The rapid cooling of the downcomer and internal RPV surface causes decreased temperature and elevated thermally driven tensile stresses in the RPV wall. This, combined with long-term material embrittlement, may cause fracture initiation at pre-existing flaws, challenging the integrity of the RPV. Assessing RPV integrity during transients with a large spatial variation in the coolant temperature requires a modeling approach that considers the effects of spatially varying coolant temperature on the fracture probability of a population of flaws distributed throughout the RPV, accounting for spatially varying embrittlement. Here, the present study addresses this need by demonstrating first-of-its-kind coupling of a high-fidelity 3D computational fluid dynamics code with 3D probabilistic fracture mechanics This was accomplished using representative models of a pressurized-water reactor subjected to small- and medium-break LOCA conditions, both of which can result in large spatial temperature variations. While the observed impact of accounting for 3D effects was minimal under the small-break LOCA this study indicates a significant increase in the probability of fracture initiation under the medium-break LOCA when 3D effects are considered, relative to a spatially uniform cooling scenario.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Experimental Investigation of Uranium Volatility during Vapor Condensation

The predictive models that describe the fate and transport of radioactive materials in the atmosphere following a nuclear incident (explosion or reactor accident) assume that uranium-bearing particulates would attain chemical equilibrium during vapor condensation. Here, we show that kinetically driven processes in a system of rapidly decreasing temperature can result in substantial deviations from chemical equilibrium. This can cause uranium to condense out in oxidation states (e.g., UO 3 vs UO 2 ) that have different vapor pressures, significantly affecting uranium transport. To demonstrate this, we synthesized uranium oxide nanoparticles using a flow reactor under controlled conditions of temperature, pressure, and oxygen concentration. The atomized chemical reactants passing through an inductively coupled plasma cool from ~5000 to 1000 K within milliseconds and form nanoparticles inside a flow reactor. The ex situ analysis of particulates by transmission electron microscopy revealed 2–10 nm crystallites of fcc-UO 2 or α-UO 3 depending on the amount of oxygen in the system. α-UO 3 is the least thermodynamically preferred polymorph of UO 3 . The absence of stable uranium oxides with intermediate stoichiometries (e.g., U 3 O 8 ) and sensitivity of the uranium oxidation states to local redox conditions highlight the importance of in situ measurements at high temperatures. Therefore, we developed a laser-based diagnostic to detect uranium oxide particles as they are formed inside the flow reactor. Our in situ measurements allowed us to quantify the changes in the number densities of the uranium oxide nanoparticles (e.g., UO 3 ) as a function of oxygen gas concentration. Our results indicate that uranium can prefer to be in metastable crystal forms (i.e., α-UO 3 ) that have higher vapor pressures than the refractory form (i.e., UO 2 ) depending on the oxygen abundance in the surrounding environment. This demonstrates that the equilibrium processes may not dominate during rapid condensation processes, and thus kinetic models are required to fully describe uranium transport subsequent to nuclear incidents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Pellet Cladding Interaction In-Reactor Ramp Testing in a World without the Halden Boiling Water Reactor

One of the most crucial performance areas for fuel rods in water cooled nuclear power plants is interaction between cladding tubes and fuel pellets. Experimental programs in test reactors have provided key data to help fuel developers and plant operators understand Pellet Cladding Interaction (PCI) phenomena and optimize their strategies for reliable fuel performance. Approximately 50 years of “ramp” testing programs, where the fission heating rate is deliberately manipulated in test rods, have been performed in a handful of test reactors to reveal and understand PCI behaviors such as iodine-assisted stress corrosion cracking. Unfortunately, the test reactors most engaged in this type of work have all been retired over the years up to the recent and unexpected closure of the Halden Boiling Water Reactor which effectively caused a hiatus in PCI ramp testing programs. The need for ramp testing is crucial at this time to enable refined PCI understanding as more plants consider implementing flexible operations, increased fuel rod burnup limits, and new fuel technologies with enhanced accident tolerance. This paper reviews some of the key PCI phenomena that must be addressed with in-pile testing and surveys past test reactor’s methods for achieving the needed conditions. A strategic approach is then presented using test reactors and complimentary facilities which are still available today. Near term data opportunities are put forth along with capability development strategies that will ensure future longevity in this field of research.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗