Search NASA⌕ Search

SEARCH · Search NASA

Results for “AILERONS, SLOTTED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Wind tunnel investigation of a large-scale semispan model with an unswept wing and an upper-surface blown jet flat

An investigation of the static longitudinal aerodynamic characteristics of a large-scale semispan model with an unswept wing and an upper-surface blown jet flap for lift augmentation was conducted in the Langley full-scale tunnel. The wing had an aspect ratio of 7.8 (3.9 for the semispan) and a simulated turbofan engine mounted ahead of and above the wing in a nacelle with a rectangular-exit nozzle. The flap system had three spanwise flap segments: (1) an inboard plain flap located behind the engine and having a large radius of curvature to provide a smooth upper surface to enhance the turning of the jet sheet, (2) a double-slotted midspan flap, and (3) a drooped aileron equipped with blowing boundary-layer control. The wing was also equipped with a full-span leading-edge Krueger flap with blowing boundary-layer control. In addition to the aerodynamic measurements, noise measurements were also included in the investigation for positions above and below the wing.

Smith, C. C., Jr.↗
NASA NTRS1979

Aerodynamic characteristics of a large-scale semispan model with a swept wing and an augmented jet flap with hypermixing nozzles

The aerodynamic characteristics of the augmentor wing concept with hypermixing primary nozzles were investigated. A large-scale semispan model in the Ames 40- by 80-Foot Wind Tunnel and Static Test Facility was used. The trailing edge, augmentor flap system occupied 65% of the span and consisted of two fixed pivot flaps. The nozzle system consisted of hypermixing, lobe primary nozzles, and BLC slot nozzles at the forward inlet, both sides and ends of the throat, and at the aft flap. The entire wing leading edge was fitted with a 10% chord slat and a blowing slot. Outboard of the flap was a blown aileron. The model was tested statically and at forward speed. Primary parameters and their ranges included angle of attack from -12 to 32 degrees, flap angles of 20, 30, 45, 60 and 70 degrees, and deflection and diffuser area ratios from 1.16 to 2.22. Thrust coefficients ranged from 0 to 2.73, while nozzle pressure ratios varied from 1.0 to 2.34. Reynolds number per foot varied from 0 to 1.4 million. Analysis of the data indicated a maximum static, gross augmentation of 1.53 at a flap angle of 45 degrees. Analysis also indicated that the configuration was an efficient powered lift device and that the net thrust was comparable with augmentor wings of similar static performance. Performance at forward speed was best at a diffuser area ratio of 1.37.

Aiken, T. N.↗
NASA NTRS1943

Wind-Tunnel Investigation of the Characteristics of Blunt-Nose Ailerons on a Tapered Wing

Characteristics are determined for various modifications of 0.155-chord blunt-nose aileron on semispan model of tapered fighter plane wing. Ailerons with 40 percent nose balance reduced high-speed stick forces. Increased balance chord increases effectiveness and reduces high-speed stick forces. Increased balance chord increases effectiveness and reduces adverse effects of gap at aileron hose. Increase of nose radii increased negative slope of curve hinge-movement coefficient plotted against deflection. Extended deflection range decreased aileron effectiveness for small deflections but increased it at large deflections. Peak pressures at noses of ailerons are relatively high at moderate deflections.

AILERONS - EFFICIENCY↗
NASA NTRS1933

The Effects of Slots and Flaps on Lateral Control of a Low-wing Monoplane as Determined in Flight

This paper presents the results of flight tests made to determine the effect of slots and flaps on the lateral control of a low-wing monoplane. Maximum angular accelerations in roll and yaw produced by sudden application of the ailerons and maximum accelerations in yaw produced by sudden application of the rudder during gliding flight were recorded for the following wing arrangements: (a) no auxiliary device; (b) full-span slots; (c) plain flaps; (d) flaps and full-span slots; (e) wing-tip slots. Rolling- and yawing-moment coefficients were derived from the accelerations. The full span slots and the flaps each had about the same influence on the aileron rolling moments. At values of the lift coefficient obtainable with the plain wing, the effect of these devices was negligible. At the higher lift coefficients obtainable with these devices, the rolling-moment coefficients increased slightly but, despite this increase, the aileron effectiveness progressively decreased with increasing lift coefficient, owing to the corresponding reduction in air speed. In the range covered by the tests, the effectiveness of the controls was appreciably reduced by the wing-tip slots. The adverse yawing moment of the ailerons experienced at the large lift coefficients obtained with the flaps was appreciably less than at similar lift coefficients obtained with either full-span or wing-tip slots. The yawing moments produced by the rudder were only slightly affected by the use of the auxiliary devices. The airplane was found to be laterally unstable with all combinations tested. Because of the angular velocities acquired in the time taken to deflect the ailerons the rolling moments recorded in flight were only about two thirds the values that would have been obtained with the wing restrained as in wind-tunnel tests.

WING SLOTS↗
NASA NTRS1932

Preliminary investigation of rolling moments obtained with spoilers on both slotted and plain wings

A wind-tunnel study has been made to determine the possibility of developing spoilers suitable for providing the lateral control for airplanes in place of the usual ailerons. The first tests were made on a model wing with a fixed tip slot, but when it was found that the effectiveness of the spoilers did not depend to any great extent on the slot, tests were made on a plain wing also. In both cases certain spoiler positions were found which were free from the usual adverse rolling moments with small deflections. Five different forms of spoiler were tested, the best ones being simple plates, either straight or slightly curved to fit the contour of the airfoil when not deflected. Sufficient rolling moment can probably be obtained from spoilers of reasonable size to provide satisfactory lateral control for certain types of airplanes.

Weick, Fred E↗
NASA NTRS1931

The Effect of Slots and Flaps on the Lift and Drag of the Mcdonnell Airplanes Determined in Flight

This note contains the results of flight test conducted by the National Advisory Committee for Aeronautics on a low-wing monoplane equipped with leading-edge slots extending over the entire wing and flaps extending only to the ailerons, to find their effect on the lift and drag characteristics of the airplane. Curves are given showing the lift and drag characteristics of the airplane for the following conditions of the slots and flaps neutral; slots closed and flaps down; and slots open and flaps down. In addition, the high and low speed in level flight and the climbing characteristics are given. The results show that the slots used alone increase the maximum lift coefficient 54 per cent; the flaps alone increase it 38 per cent; and the slots and flaps in combination decrease the landing speed from 60 to 43 m.p.h.; increase the speed range of the airplane 40 per cent; and increase the glide angle at landing speed 4.2 degrees.

Soule, Hartley A↗
NASA NTRS1979

Low-speed wind-tunnel tests of a 1/10-scale model of an advanced arrow-wing supersonic cruise configuration designed for cruise at Mach 2.2

The low-speed longitudinal and lateral-directional characteristics of a scale model of an advanced arrow-wing supersonic cruise configuration were investigated in tests conducted at a Reynolds number of 4.19 x 10 to the 6th power based on the mean aerodynamic chord, with an angle of attack range from - 6 deg to 23 deg and sideslip angle range from -15 deg to 20 deg. The effects of segmented leading-edge flaps, slotted trailing-edge flaps, horizontal and vertical tails, and ailerons and spoilers were determined. Extensive pressure data and flow visualization pictures with non-intrusive fluorescent mini-tufts were obtained.

Yip, L. P.↗
NASA NTRS1925

Results of recent experiments with slotted wings

This report gives the results of a recent series of experiments performed on a wing designed for a cantilever monoplane. Both wings were trapezial in their ground plan, with their tips rounded elliptically. These wing sections combine all known devices for increasing the lift, namely, the slot, the increased camber and angle of attack by means of an aileron running the whole length of the span. The last advance included in the wing section was an increase in wing area by means of an auxiliary wing adjusted by a sort of rectangular joint.

BOUNDARY LAYER THICKNESS↗
NASA NTRS1979

Low-speed aerodynamic performance of a high-aspect-ratio supercritical-wing transport model equipped with full-span slat and part-span double-slotted flaps

An investigation was conducted in the Langley V/STOL tunnel to determine the static longitudinal and lateral-directional aerodynamic characteristics of an advanced high-aspect-ratio supercritical-wing transport model equipped with a full-span leading-edge slat and part-span double-slotted trailing-edge flaps. This wide-body transport model was also equipped with spoiler and aileron control surfaces, flow-through nacelles, landing gear, movable horizontal tails, and interchangeable wing tips with aspect ratios of 10 and 12. The model was tested with leading-edge slat and trailing-edge flap combinations representative of cruise, climb, takeoff, and landing wing configurations. The tests were conducted at free-stream conditions corresponding to Reynolds numbers (based on mean geometric chord) of 0.97 to 1.63 x 10 to the 6th power and corresponding Mach numbers of 0.12 to 0.20, through an angle-of-attack range of -2 deg to 24 deg and a sideslip-angle range of -10 deg to 5 deg.

Morgan, H. L., Jr.↗