Search NASA⌕ Search

SEARCH · Search NASA

Results for “ASTM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Acceptance criteria for welds in ASTM A106 grade B steel pipe and plate

Based on the RECERT Program findings, NASA-Langley funded a fatigue study of code-unacceptable welds. Usage curves were developed which were based on the structural integrity of the welds. The details of this study are presented in NASA CR-178114. The information presented is a condensation and reinterpretation of the information in NASA CR-178114. This condensation and reinterpretation generated usage curves for welds having: (1) indications 0.20 -inch deep by 0.40-inch long, and (2) indications 0.195-inch deep by 8.4-inches long. These curves were developed using the procedures used in formulating the design curves in Section VIII, Division 2 of the American Society of Mechanical Engineers Boiler and Pressure Vessel Code.

Hudson, C. M.↗
NASA NTRS1989

Results of the Round Robin on opening-load measurement conducted by ASTM Task Group E24.04.04 on Crack Closure Measurement and Analysis

An experimental Round Robin on the measurement of the opening load in fatigue crack growth tests was conducted on Crack Closure Measurement and Analysis. The Round Robin evaluated the current level of consistency of opening load measurements among laboratories and to identify causes for observed inconsistency. Eleven laboratories participated in the testing of compact and middle-crack specimens. Opening-load measurements were made for crack growth at two stress-intensity factor levels, three crack lengths, and following an overload. All opening-load measurements were based on the analysis of specimen compliance data. When all of the results reported (from all participants, all measurement methods, and all data analysis methods) for a given test condition were pooled, the range of opening loads was very large--typically spanning the lower half of the fatigue loading cycle. Part of the large scatter in the reported opening-load results was ascribed to consistent differences in results produced by the various methods used to measure specimen compliance and to evaluate the opening load from the compliance data. Another significant portion of the scatter was ascribed to lab-to-lab differences in producing the compliance data when using nominally the same method of measurement.

Phillips, Edward P.↗
NASA NTRS1988

ASTM Committee G-4 metals flammability test program - Data and discussion

Results of metals flammability tests performed on twenty-six metals in the NASA/White Sands Test Facility are discussed together with the test systems. The promoted combustion and ignition characteristics of these metals are described, and the metals are ranked according to their suitability for use in oxygen systems. In general, alloys with high copper and nickel contents and low iron content were found to rank higher than those that had high iron content, while alloys that had high aluminum content were ranked the lowest.

Stoltzfus, Joel M.↗
NASA NTRS2000

Model of ASTM Flammability Test in Microgravity: Iron Rods

There is extensive qualitative results from burning metallic materials in a NASA/ASTM flammability test system in normal gravity. However, this data was shown to be inconclusive for applications involving oxygen-enriched atmospheres under microgravity conditions by conducting tests using the 2.2-second Lewis Research Center (LeRC) Drop Tower. Data from neither type of test has been reduced to fundamental kinetic and dynamic systems parameters. This paper reports the initial model analysis for burning iron rods under microgravity conditions using data obtained at the LERC tower and modeling the burning system after ignition. Under the conditions of the test the burning mass regresses up the rod to be detached upon deceleration at the end of the drop. The model describes the burning system as a semi-batch, well-mixed reactor with product accumulation only. This model is consistent with the 2.0-second duration of the test. Transient temperature and pressure measurements are made on the chamber volume. The rod solid-liquid interface melting rate is obtained from film records. The model consists of a set of 17 non-linear, first-order differential equations which are solved using MATLAB. This analysis confirms that a first-order rate, in oxygen concentration, is consistent for the iron-oxygen kinetic reaction. An apparent activation energy of 246.8 kJ/mol is consistent for this model.

Steinberg, Theodore A↗
NASA NTRS2010

New ASTM Standards for Nondestructive Testing of Aerospace Composites

Problem: Lack of consensus standards containing procedural detail for NDE of polymer matrix composite materials: I. Flat panel composites. II. Composite components with more complex geometries a) Pressure vessels: 1) composite overwrapped pressure vessels (COPVs). 2) composite pressure vessels (CPVs). III. Sandwich core constructions. Metal and brittle matrix composites are a possible subject of future effort.

Waller, Jess M.↗
NASA NTRSDate not supplied

ASTM International Conference on Additive Manufacturing – 2022

The In-Situ Project: Correlating In-situ monitoring data and Non-Destructive Evaluation (NDE) methods to characterize defect populations in Laser Powder Bed Fusion (L-PBF) material NDE is critical to enable the safe use of additive manufactured (AM) parts in aerospace applications. However, traditional NDE methods are not fully adaptable to complex AM geometries to appropriately screen for critical defects, and L-PBF processes inherently generate defects. In-situ monitoring techniques can give information about the quality of the build process and indicate process variations that could potentially create defects. Proven, causal correlations between in-situ monitoring indications and resulting defects are needed to inform about the final quality of the part. Thus, the development of a new approach is necessary. NASA started a two-phase study that would investigate techniques for characterizing defect populations in L-PBF material, first in material with induced defects, then in a nominal L-PBF process, by correlating in-situ, NDE, and serial sectioning data. Objectives also include the evaluation of seeded defect methodologies for realistic defect creation, creating a baseline of defect populations in a Qualified Material Process (QMP), characterizing the effect of heat treatment, and correlating defect populations with tensile and fatigue properties. By comparing computed tomography images, in-situ monitoring images, and metallography images, the team has been able to draw preliminary conclusions. They include a better understanding of the limitation of the NDE tools, learning about the “healing” of the samples observed during layer building and a comparison study on different laser power variation samples. Those preliminary conclusions will help dictate the follow-up work that will be presented at the conference.

additive manufacturing↗