Results for “AUTOROTATION” — Page 4

NASA NTRS1984

Preliminary results of experimental and analytical investigations of the tumbling phenomenon for an advanced configuration

A sustained autorotative pitching motion usually called 'tumbling' has been observed during dynamic model tests of the X-29A configuration. The X-29 is an advanced design incorporating forward-swept wings and canards in a highly relaxed static stability condition. Beginning with a historical review of the tumbling phenomenon, this paper discusses the current experimental results of dynamic model tumbling tests of the X-29 and the initial efforts to establish an aerodynamic and mathematical model for analysis.

Whipple, R. D.↗

NASA NTRS1986

Structural and aerodynamic loads and performance measurements of an SA349/2 helicopter with an advanced geometry rotor

A flight test program was conducted to obtain data from an upgraded Gazelle helicopter with an advanced geometry, three bladed rotor. Data were acquired on upper and lower surface chordwise blade pressure, blade bending and torsion moments, and fuselage structural loads. Results are presented from 16 individual flight conditions, including level flights ranging from 10 to 77 m/sec at 50 to 3000 m altitude, turning flights up to 2.0 g, and autorotation. Rotor aerodynamic data include information from 51 pressure transducers distributed chordwise at 75, 88, and 97% radial stations. Individual tranducer pressure coefficients and airfoil section lift and pitching moment coefficients are presented, as are steady state flight condition parameters and time dependence rotor loads. All dynamic data are presented as harmonic analysis coefficients.

Heffernan, Ruth M.↗

NASA NTRS1988

Simulating Unpowered Helicopter Landings

Report presents results of experiment with visual, aural, and motion cues in simulations of helicopter landings without engine power. Helicopter simulators do not offer realistic environment, particularly in sensory cues for near-ground, low-speed flight. Evaluated importance of various cues in difficult autorotation. Conducted in vertical-motion simulator with experienced pilots as subjects.

Decker, William A.↗

NASA NTRS1988

Structural optimization of rotor blades with integrated dynamics and aerodynamics

The problem of structural optimization of helicopter rotor blades with integrated dynamic and aerodynamic design considerations is addressed. Results of recent optimization work on rotor blades for minimum weight with constraints on multiple coupled natural flap-lag frequencies, blade autorotational inertia and centrifugal stress has been reviewed. A strategy has been defined for the ongoing activities in the integrated dynamic/aerodynamic optimization of rotor blades. As a first step, the integrated dynamic/airload optimization problem has been formulated. To calculate system sensitivity derivatives necessary for the optimization recently developed, Global Sensitivity Equations (GSE) are being investigated. A need for multiple objective functions for the integrated optimization problem has been demonstrated and various techniques for solving the multiple objective function optimization are being investigated. The method called the Global Criteria Approach has been applied to a test problem with the blade in vacuum and the blade weight and the centrifugal stress as the multiple objectives. The results indicate that the method is quite effective in solving optimization problems with conflicting objective functions.

Chattopadhyay, Aditi↗

NASA NTRS1989

Integrated aerodynamic/dynamic optimization of helicopter rotor blades

An integrated aerodynamic/dynamic optimization procedure is used to minimize blade weight and 4 per rev vertical hub shear for a rotor blade in forward flight. The coupling of aerodynamics and dynamics is accomplished through the inclusion of airloads which vary with the design variables during the optimization process. Both single and multiple objective functions are used in the optimization formulation. The Global Criteria Approach is used to formulate the multiple objective optimization and results are compared with those obtained by using single objective function formulations. Constraints are imposed on natural frequencies, autorotational inertia, and centrifugal stress. The program CAMRAD is used for the blade aerodynamic and dynamic analyses, and the program CONMIN is used for the optimization. Since the spanwise and the azimuthal variations of loading are responsible for most rotor vibration and noise, the vertical airload distributions on the blade, before and after optimization, are compared. The total power required by the rotor to produce the same amount of thrust for a given area is also calculated before and after optimization. Results indicate that integrated optimization can significantly reduce the blade weight, the hub shear and the amplitude of the vertical airload distributions on the blade and the total power required by the rotor.

Chattopadhyay, Aditi↗

NASA NTRS1989

Structural optimization of rotor blades with integrated dynamics and aerodynamics

The problem of structural optimization of helicopter rotor blades with integrated dynamic and aerodynamic design considerations is addressed. Results of recent optimization work on rotor blades for minimum weight with constraints on multiple coupled natural flap-lag frequencies, blade autorotational inertia and centrifugal stress has been reviewed. A strategy has been defined for the ongoing activities in the integrated dynamic/aerodynamic optimization of rotor blades. As a first step, the integrated dynamic/airload optimization problem has been formulated. To calculate system sensitivity derivatives necessary for the optimization recently developed, Global Sensitivity Equations (GSE) are being investigated. A need for multiple objective functions for the integrated optimization problem has been demonstrated and various techniques for solving the multiple objective function optimization are being investigated. The method called the Global Criteria Approach has been applied to a test problem with the blade in vacuum and the blade weight and the centrifugal stress as the multiple objectives. The results indicate that the method is quite effective in solving optimization problems with conflicting objective functions.

Chattopadhyay, Aditi↗

NASA NTRS1990

An enhanced integrated aerodynamic load/dynamic optimization procedure for helicopter rotor blades

An enhanced integrated aerodynamic load/dynamic optimization procedure is developed to minimize vibratory root shears and moments. The optimization is formulated with 4/rev vertical and 3/rev inplane shears at the blade root as objective functions and constraints, and 4/rev lagging moment. Constraints are also imposed on blade natural frequencies, weight, autorotational inertia, centrifugal stress, and rotor thrust. The 'Global Criteria Approach' is used for formulating the multi-objective optimization. Design variables include spanwise distributions of bending stiffnesses, torsional stiffness, nonstructural mass, chord, radius of gyration, and blade taper ratio. The program CAMRAD is coupled with an optimizer, which consists of the program CONMIN and an approximate analysis, to obtain optimum designs. The optimization procedure is applied to an advanced rotor as a reference design. Optimum blade designs, obtained with and without a constraint on the rotor thrust, are presented and are compared to the reference blade. Substantial reductions are obtained in the vibratory root forces and moments. As a byproduct, improvements are also found in some performance parameters, such as total power required, which were not considered during optimization.

Chattopadhyay, Aditi↗

NASA NTRS1990

Aeroelastic optimization of a helicopter rotor using an efficient sensitivity analysis

To reduce oscillatory hub loads in forward flight, a structural optimization analysis of a hingeless helicopter rotor has been developed and applied. The aeroelastic analysis of the rotor is based on a finite element method in space and time, and linked with automated optimization algorithms. For the optimization analysis two types of structural representation are used: a generic stiffness-distribution and a single-cell thin-walled beam. For the first type, the design variables are nonstructural mass and its placement, chordwise center of gravity offset from the elastic axis, and stiffness. For the second type, width, height and thickness of spar are used as design variables. For the behavior constraints, frequency placement, autorotational inertia and aeroelastic stability of the blade are included. The required sensitivity derivatives are obtained using a direct analytical approach. An optimum oscillatory hub load shows a 25-77 percent reduction for the generic blade, and 30-50 percent reduction for the box-beam.

Lim, Joon W.↗

NASA NTRS1990

Application of optimization methods to helicopter rotor blade design

A procedure for the minimum weight design of helicopter rotor blades with constraints on multiple coupled flap-lag natural frequencies, autorotational inertia, and centrifugal stress is presented. Optimum designs are obtained for blades with both rectangular and tapered planforms and are compared within a reference blade. The effects of higher-frequency constraints and stress constraints on the optimum blade designs are assessed. The results indicate that there is an increase in blade weight and a significant change in the design variable distributions with an increase in the number of frequency constraints. The inclusion of stress constraints has different effects on the wall thickness distributions of rectangular and tapered blades, but tends to increase the magnitude of the nonstructural segment weight distributions for both blade types.

Chattopadhyay, A.↗

NASA NTRS1990

An enhanced integrated aerodynamic load/dynamic approach to optimum rotor blade design

An enhanced integrated aerodynamic load/dynamic optimization procedure is developed to minimize vibratory root shears and moments. The optimization is formulated with 4/rev vertical and 3/rev inplane shears at the blade root as objective functions and constraints, and 4/rev lagging moment. Constraints are also imposed on blade natural frequencies, weight, autorotational inertia, contrifugal stress, and rotor thrust. The Global Criteria Approach is used for formulating the multi-objective optimization. Design variables include spanwise distributions of bending stiffnesses, torsional stiffness, nonstructural mass, chord, radius of gyration, and blade taper ratio. The program CAMRAD is coupled with an optimizer, which consists of the program CONMIN and an approximate analysis, to obtain optimum designs. The optimization procedure is applied to an advanced rotor as a reference design. Optimum blade designs, obtained with and without a constraint on the rotor thrust, are presented and are compared to the reference blade. Substantial reductions are obtained in the vibratory root forces and moments. As a byproduct, improvements are also found in some performance parameters, such as total power required, which were not considered during optimization.

Chattopadhyay, Aditi↗

NASA NTRS1992

Fully integrated aerodynamic/dynamic optimization of helicopter rotor blades

A fully integrated aerodynamic/dynamic optimization procedure is described for helicopter rotor blades. The procedure combines performance and dynamic analyses with a general purpose optimizer. The procedure minimizes a linear combination of power required (in hover, forward flight, and maneuver) and vibratory hub shear. The design variables include pretwist, taper initiation, taper ratio, root chord, blade stiffnesses, tuning masses, and tuning mass locations. Aerodynamic constraints consist of limits on power required in hover, forward flight and maneuvers; airfoil section stall; drag divergence Mach number; minimum tip chord; and trim. Dynamic constraints are on frequencies, minimum autorotational inertia, and maximum blade weight. The procedure is demonstrated for two cases. In the first case, the objective function involves power required (in hover, forward flight and maneuver) and dynamics. The second case involves only hover power and dynamics. The designs from the integrated procedure are compared with designs from a sequential optimization approach in which the blade is first optimized for performance and then for dynamics. In both cases, the integrated approach is superior.

Walsh, Joanne L.↗

NASA NTRS1992

Fully integrated aerodynamic/dynamic optimization of helicopter rotor blades

This paper describes a fully integrated aerodynamic/dynamic optimization procedure for helicopter rotor blades. The procedure combines performance and dynamics analyses with a general purpose optimizer. The procedure minimizes a linear combination of power required (in hover, forward flight, and maneuver) and vibratory hub shear. The design variables include pretwist, taper initiation, taper ratio, root chord, blade stiffnesses, tuning masses, and tuning mass locations. Aerodynamic constraints consist of limits on power required in hover, forward flight and maneuver; airfoil section stall; drag divergence Mach number; minimum tip chord; and trim. Dynamic constraints are on frequencies, minimum autorotational inertia, and maximum blade weight. The procedure is demonstrated for two cases. In the first case the objective function involves power required (in hover, forward flight, and maneuver) and dynamics. The second case involves only hover power and dynamics. The designs from the integrated procedure are compared with designs from a sequential optimization approach in which the blade is first optimized for performance and then for dynamics. In both cases, the integrated approach is superior.

Walsh, Joanne L.↗

NASA NTRS1951

Empirical relation between induced velocity, thrust, and rate of descent of a helicopter rotor as determined by wind-tunnel tests on four model rotors

The empirical relation between the induced velocity, thrust, and rate of vertical descent of a helicopter rotor was calculated from wind tunnel force tests on four model rotors by the application of blade-element theory to the measured values of the thrust, torque, blade angle, and equivalent free-stream rate of descent. The model tests covered the useful range of C(sub t)/sigma(sub e) (where C(sub t) is the thrust coefficient and sigma(sub e) is the effective solidity) and the range of vertical descent from hovering to descent velocities slightly greater than those for autorotation. The three bladed models, each of which had an effective solidity of 0.05 and NACA 0015 blade airfoil sections, were as follows: (1) constant-chord, untwisted blades of 3-ft radius; (2) untwisted blades of 3-ft radius having a 3/1 taper; (3) constant-chord blades of 3-ft radius having a linear twist of 12 degrees (washout) from axis of rotation to tip; and (4) constant-chord, untwisted blades of 2-ft radius. Because of the incorporation of a correction for blade dynamic twist and the use of a method of measuring the approximate equivalent free-stream velocity, it is believed that the data obtained from this program are more applicable to free-flight calculations than the data from previous model tests.

Castles, Walter, Jr.↗

NASA NTRS1990

Current projects in Fuzzy Control

Viewgraphs on current projects in fuzzy control are presented. Three projects on helicopter flight control are discussed. The projects are (1) radio control by oral instructions; (2) automatic autorotation entry in engine failure; and (3) unmanned helicopter for sea rescue.

Sugeno, Michio↗

NASA NTRS1993

A model for tropical-extratropical transport of volcanic ash in the lower stratosphere

Large nonspherical volcanic ash particles up to 30 micrometer in size were collected between 17-19 km altitude over the Northern Hemisphere at high latitudes between October 1988 and April 1990. These particles may be derived from minor Plinian eruptions in the tropics rather than from localized volcanic activity close to the collection region. Ash particles were injected into the lower equatorial stratosphere where they entered a regime of efficient transport just above the tropopause from the tropical region towards the northern extratropical region. Transport is enhanced by stable autorotation that generates a sufficient lift force to loft nonspherical ash with a rough surface during transport, and by the gradually decreasing altitude of the tropopause from the tropics to the polar regions.

Rietmeijer, Frans J. M.↗

NASA NTRS1993

Effect of geometry, static stability, and mass distribution on the tumbling characteristics of generic flying-wing models

Results from an investigation to determine the low-speed tumbling characteristics of twelve generic flying-wing models are summarized. There is a concern that airplanes with flying-wing planforms could inadvertently enter an out-of-control tumbling motion under certain conditions. The objectives of this investigation were to: 1) identify the geometric and mass-related parameters that cause flying wings to be capable of sustained tumbling, 2) analyze some of the driving mechanisms that cause tumbling, and 3) determine the feasibility of using computer simulations to predict the tumbling characteristics of flying wings. Free-tumble and free-to-pitch tests were conducted with dynamically-scaled, generic flying wing models. The use of computer simulations as a predictive tool for tumbling was explored. Results indicated that center-of-gravity location, mass distribution, and geometric aspect ratio strongly affected the tumbling characteristics of the models tested and that positive static stability did not necessarily preclude tumbling. The magnitude of dynamic effects were found to be of the same order as static effects for the models undergoing autorotation-in-pitch. The simulations indicated that the dynamic terms in the equations of motion used to predict tumbling must be obtained using experimental methods that account for the large amplitude/high pitch-rate environment that characterizes tumbling.

Fremaux, C. M.↗

NASA NTRS1932

Effect of length of Handley Page tip slots on the lateral-stability factor, damping in roll

Tests have been made in the NACA 7 by 10 foot wind tunnel on a Clark Y wing model equipped with various lengths of Handley Page slots extending inward from the wing tips. The slot lengths tested ranged from 20 to 100 per cent of the semi span. The effect of slot lengths on damping in roll was determined by means of both free-autorotation and forced-rotation test. In addition, the maximum lift coefficient was found with each slot length. The optimum length of slot for satisfactory damping in roll over a large range of angles of attack was found to be slightly over 50 per cent of the semispan for the form of slot tested.

Weick, Fred E↗

NASA NTRS1951

Empirical Relation Between Induced Velocity, Thrust, and Rate of Descent of a Helicopter Rotor as Determined by Wind-tunnel Tests on Four Model Rotors

The empirical relation between the induced velocity, thrust, and rate of vertical descent of a helicopter rotor was calculated from wind tunnel force tests on four model rotors by the application of blade-element theory to the measured values of the thrust, torque, blade angle, and equivalent free-stream rate of descent. The model tests covered the useful range of C(sub t)/sigma(sub e) (where C(sub t) is the thrust coefficient and sigma(sub e) is the effective solidity) and the range of vertical descent from hovering to descent velocities slightly greater than those for autorotation. The three bladed models, each of which had an effective solidity of 0.05 and NACA 0015 blade airfoil sections, were as follows: (1) constant-chord, untwisted blades of 3-ft radius; (2) untwisted blades of 3-ft radius having a 3/1 taper; (3) constant-chord blades of 3-ft radius having a linear twist of 12 degrees (washout) from axis of rotation to tip; and (4) constant-chord, untwisted blades of 2-ft radius. Because of the incorporation of a correction for blade dynamic twist and the use of a method of measuring the approximate equivalent free-stream velocity, it is believed that the data obtained from this program are more applicable to free-flight calculations than the data from previous model tests.

Castles, Walter, Jr↗