Search NASA⌕ Search

SEARCH · Search NASA

Results for “AXIAL COMPRESSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1962

DEVELOPMENT OF DESIGN STRENGTH LEVELS FOR THE ELASTIC STABILITY OF MONOCOQUE CONES UNDER AXIAL COMPRESSION

Design relationships have been derived for the determination of elastic buckling strength levels for unpressurized monocoque truncated cones under axial compression. Theoretical implications have been considered in the establishment of a semi-empirical analysis leading to the development of probability based design expressions. Data from 170 tests by various investigators were statistically evaluated for the expected mean, 90%, and 99% probability strength levels. Dispersion of data was found to be slightly less than that of monocoque cylinders. Non-linear effects of radius to thickness ratio or strength deterioration with length to radius ratio were not discernible.

AXIAL COMPRESSION↗
NASA NTRS1994

Actuator Exerts Tensile Or Compressive Axial Load

Compact, manually operated mechanical actuator applies controlled, limited tensile or compressive axial force. Designed to apply loads to bearings during wear tests in clean room. Intended to replace hydraulic actuator. Actuator rests on stand and imparts axial force to part attached to clevis inside or below stand. Technician turns control screw at one end of lever. Depending on direction of rotation of control screw, its end of lever driven downward (for compression) or upward (for tension). Lever pivots about clevis pin at end opposite of control screw; motion drives downward or upward link attached via shearpin at middle of lever. Link drives coupling and, through it, clevis attached to part loaded.

Nozzi, John↗
NASA NTRS1967

Analysis of stability-critical orthotropic cylinders subjected to axial compression

Analytical procedure for determining critical buckling loads of orthotropic cylinders subjected to axial compression loading has been defined. Three modes of instability have been considered - general instability, local instability caused by panel and interframe buckling, and local instability caused by yielding and crippling in areas of stress concentration.

Finley, R. L.↗
NASA NTRS1976

Buckling of eccentrically stringer-stiffened cylindrical panels under axial compression

The paper presents numerical results, based on Donnell shell theory, for the axial compressive buckling loads for eccentrically stringer-stiffened circular cylindrical panels, in a study of the effect of boundary conditions and panel width on the buckling load. The two cases of inside and outside stiffeners were considered. The complete cylinder buckling load was reached only for panels under classical simply supported boundary conditions. The prevention of circumferential displacement is found to be the most important in-plane boundary condition from the point of view of increasing the buckling load. Clamping is found more effective in increasing the buckling loads of panels with free circumferential edge displacement than of panels with zero edge displacement. When panel width is equal to or greater than 180 deg, the panel buckling loads are within 10% of the complete cylinder load for all cases except one simply supported panel with outside stringers. Buckling loads were higher for outside stringers, except for very narrow panels that are restrained against circumferential edge displacement. Eccentricity effects are generally similar for clamped and simply supported panels with the same in-plane boundary conditions.

Sobel, L. H.↗
NASA NTRSDate not supplied

Scaling Methodology for Buckling of Composite Conical Shells in Axial Compression

Conical shells are commonly used as structural components for launch vehicles. The axial compression experienced during launch is one of the sizing load cases, because it can lead to loss of stability. As Because experimentally testing these large full-scale structures is cumbersome and expensive, it is studied how reduced-scale shells can be designed such that their buckling behavior is representative of the full-scale scale shell behavior. An analytical, sequential scaling procedure methodology is developed based on the nondimensional governing equations for composite conical shells with a symmetric, balanced layup and negligible flexural anisotropy. The buckling behavior of the shells of different size is compared using linear and nonlinear finite element analyses, and good comparisons . Accurate results are obtained for the considered shells in terms of buckling load, displacement, and mode. The inclusion of a geometric imperfections affects reduces the prediction accuracy, but it does not to the extent that the methodology is no longer valid cause the methodology to fail.

Buckling↗
NASA NTRS1955

On the mechanism of buckling of a circular cylindrical shell under axial compression

The present paper deals with the buckling of a circular cylindrical shell under axial compression from the viewpoint of energy and the characteristics of deformation. It is shown first, both theoretically and experimentally, that the reason why the buckling of a cylindrical shell is quite different from that of a flat plate is attributable to the existence of a nearly developable surface far apart from the original cylindrical surface. Based upon this result, the experimental fact that the buckling is really not general but local, that is, that the buckled region is limited axially to a range of 1.5 times the wave length of the lobe, is explained by the theoretical result that the minimum buckling load is smaller in the local buckling than in the general buckling case. The occurrence of local buckling is affirmed also from the viewpoint of the energy barrier to be jumped over during buckling, and from a comparison of the theoretical post-buckling state with the experimental results. Finally, the local buckling with the load applied by a spring is analyzed, and it is proved that the minimum buckling load increased with an increase of rigidity of the spring.

SHELLS, STRUCTURAL↗
NASA NTRS1976

Buckling of Cylindrical Panels Under Axial Compression

This paper investigates the effects of boundary conditions and panel width on the axially compressive buckling behavior of unstiffened, isotropic, circular cylindrical panels. Numerical results are presented for eight different sets of boundary conditions along the straight edges of the panels. For all sets of boundary conditions except one (SSI), the results show that the panel buckling loads monotonically approach the complete cylinder buckling load from above as the panel width is increased. Low buckling loads, sometimes less than half the complete cylinder buckling load, are found for simply supported panels with free in-plane edge displacements (SSI). The SSI buckling loads are below the complete cylinder load even for '360deg panels'. It is also observed that the prevention of circumferential edge displacement is the most important in-plane boundary condition from the point of view of increasing the buckling load, and that the prevention of edge rotation (i.e. clamping) in the circumferential direction also significantly increases the buckling load. Parametric studies are also performed to determine the effects of variations in panel length and thickness on the buckling loads.

Sobel, L. H.↗
NASA NTRS1991

Aerothermal study in an axial compression corner with shock impingement at Mach 6

An experimental study of an axial-compression interior-corner region with shock impingement was conducted in the NASA Langley 20-inch Mach 6 Tunnel to obtain aerodynamic heating rate distributions. The model, a generic hypersonic engine inlet, had a sharp leading edge forebody, cowl, and interchangeable struts with sharp and blunt leading edges. Experiments were conducted at free-stream unit Reynolds numbers of 1.68 x 10 to the 6th and 3.35 x 10 to the 6th per foot for the blunt and sharp-strut configurations, respectively. For the sharp-strut configuration, with and without trips, the peak heating occurred on the cowl, near the compression corner, downstream of the forebody oblique shock impingement region. The peak heating levels, for both the tripped and untripped boundary-layer flows were about 45 and 50 times the reference laminar heating levels, respectively. The peak heating for the blunt leading edge strut model, which was 30 times the reference value, occurred on the cowl, away from the corner, where the bow shock from the strut leading edge intersected the cowl surface.

Venkateswaran, S.↗
NASA NTRS1990

Innovative design of composite structures: Axisymmetric deformations of unsymmetrically laminated cylinders loaded in axial compression

The study focuses on the axisymmetric deformation response of unsymmetrically laminate cylinders loaded in axial compression by known loads. A geometrically nonlinear analysis is used. Though buckling is not studied, the deformations can be considered to be the prebuckling response. Attention is directed at three 16 layer laminates: a (90 sub 8/0 sub 8) sub T; a (0 sub 8/90 sub 8) sub T and a (0/90) sub 4s. The symmetric laminate is used as a basis for comparison, while the two unsymmetric laminates were chosen because they have equal but opposite bending-stretching effects. Particular attention is given to the influence of the thermally-induced preloading deformations that accompany the cool-down of any unsymmetric laminate from the consolidation temperature. Simple support and clamped boundary conditions are considered. It is concluded that: (1) The radial deformations of an unsymmetric laminate are significantly larger than the radial deformations of a symmetric laminate, although for both symmetric and unsymmetric laminates the large deformations are confined to a boundary layer near the ends of the cylinder; (2) For this nonlinear problem the length of the boundary layer is a function of the applied load; (3) The sign of the radial deformations near the supported end of the cylinder depends strongly on the sense (sign) of the laminate asymmetry; (4) For unsymmetric laminates, ignoring the thermally-induced preloading deformations that accompany cool-down results in load-induced deformations that are under predicted; and (5) The support conditions strongly influence the response but the influence of the sense of asymmetry and the influence of the thermally-induced preloading deformations are independent of the support conditions.

Hyer, M. W.↗