Search NASA⌕ Search

SEARCH · Search NASA

Results for “Additive Manufactured 316 Stainless Steels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Formation of functionally graded steel by laser powder bed fusion via in-situ carbon doping

Additive Manufacturing (AM) enables functional integration by combining multiple components into a single part to shorten assembly time, reduce weight, and improve performance. Laser Powder Bed Fusion (LPBF) is an important AM method due to excellent spatial resolution, surface finish, and material properties without the need for extensive post-processing. Functional integration could be enhanced by spatial tuning of properties, but LPBF cannot readily vary material composition. Here, this paper addresses a method to add spatial composition control by printing small quantities of dopants via liquid carrier prior to laser fusion. The impact of carbon black suspension added to select regions of a Stainless Steel 316 L powder bed on melt pool dimension, hardness, and porosity is reported. The distribution of the carbon between the doped and plain layers and the resulting spatial variation in hardness is measured. Optical microscopy and composition analysis show that the carbon dispersed uniformly within the layer of deposition and diffused as little as 50 μm in the build direction. Keyhole conditions dramatically increase the inter-layer transport of the dopant. The added carbon increased hardness by >50 %. Porosity increased in doped regions but remained below 1.5 % for the best processing parameters. These results demonstrate that the composition of LPBF parts could be controlled in 3-dimensions using a dopant that is soluble in the melt pool. Additional work will be required to evaluate different dopant materials and optimize processing conditions for full density, but microalloying with soluble dopants appears to be a plausible solution to enhance functional integration with LPBF.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In situ embedment of type K sheathed thermocouples with directed energy deposition

Advanced nuclear reactor systems require new technologies for heat transfer and system monitoring. Additive manufacturing (AM) offers the design flexibility to allow in-situ sensor embedment through smart manufacturing for real-time monitoring, and performance of these systems. Here, this study focuses on experiments investigating the feasibility of in-situ sensor embedment using directed energy deposition (DED). Type K thermocouples are embedded into 316L stainless steel (SS) samples using two different configurations (e.g., exposed and embedded tips) and two designs (e.g., flush to substrate) within an AM base. Embedded sensor samples are analyzed via in-situ measurements and high-temperature performance validation tests at 350ºC and 900ºC. Temperature performance results at both temperature tests show good agreement with manufacturer specifications proving that these sensors could still capture accurate temperature readings after in-situ embedment during DED processing. An additional optimization experiment was conducted on the exposed tip configuration using a surrogate thermocouple to improve tolerances and the embedment process. Results improved tolerances, lower porosity, smaller gaps between the sensor and base, and better junction contact for the sensor. Although further optimization of this embedment strategy is necessary to improve the structural stability and tolerances within the component, this research strategy provides a proof-of-feasibility for DED embedment with commercial sheathed thermocouples. This research provides early impact on embedment of sensor for multiple materials and complex geometric components..

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2020

Assessment of the Material Performance for TCR Applications (Progress Report)

The objective of Argonne’s materials research activities for the Transformational Challenge Reactor (TCR) program is to improve the understanding of material properties from additive manufacturing with the focus on understanding the creep and fatigue properties of additively manufactured materials. The material work conducted by Argonne provides support in developing and qualifying advanced materials and manufacturing processes to allow for innovative reactor design and licensing for the TCR. In FY 2020, Oak Ridge National Laboratory (ORNL) provided six ASTM standard sized creep specimens of additively-manufactured 316L stainless steel (AM 316L SS) for evaluation of the effect of post-build heat treatment on the creep property. Two different teat treatments were conducted on the as-built specimens, namely 1050°C/1h and 650°C/1h before creep testing. All specimens were creep tested at 550°C and 275 MPa to understand the effect of heat treatments. We have also received AM 316L SS printed in various forms including rods and sheets, wrought 316 L SS (as a reference material), and AM IN718 for tensile, creep and fatigue testing. Both ASTM standard sized specimens and subsized specimens are being fabricated or tested to contribute to a comprehensive mechanical property database of AM materials and to provide location-specific property data to the TCR digital platform. Mechanical testing at Argonne is conducted to ASME NQA-1 or its lab equivalent for quality assurance. This report presents the results of the creep tests at 550°C and microstructural characterization for the assessment of the effect of the post-build heat treatment on the creep behavior of AM 316L SS. It also discusses ongoing efforts on obtaining location-dependent properties of AM 316L SS.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Application of Refractory High-Entropy Alloys for Higher-Reliability and Higher-Efficiency Brayton Cycles and Advanced Nuclear Reactors

An exceptional set of newly-discovered advanced superalloys known as refractory high-entropy alloys (RHEAs) can provide near-term solutions for wear, erosion, corrosion, high-temperature strength, creep, and radiation issues associated with supercritical carbon dioxide (sCO2) Brayton Cycles and advanced nuclear reactors. In particular, these superalloys can significantly extend their durability, reliability, and thermal efficiency, thereby making them more cost-competitive, safer, and reliable. For this project, it was endeavored to manufacture and test certain RHEAs, to solve technical issues impacting the Brayton Cycle and advanced nuclear reactors. This was achieved by leveraging Sandia’s patents, technical advances, and previous experience working with RHEAs. Herein, three RHEA manufacturing methods were applied: laser engineered net shaping, spark plasma sintering, and spray coating. Two promising RHEAs were selected, HfNbTaZr and MoNbTaVW. To demonstrate their performance, erosion, structural, radiation, and hightemperature experiments were conducted on the RHEAs, stainless steel (SS) 316 L, SS 1020, and Inconel 718 test coupons, as well as bench-top components. The experimental data is presented, analyzed, and confirms the superior performance of the HfNbTaZr and MoNbTaVW RHEAs vs. SS 316 L, SS 1020, and Inconel 718. In addition, to gain more insights for larger-scale RHEA applications, the erosion and structural capabilities for the two RHEAs were simulated and compared with the experimental data. The experimental data confirm the superior performance of the HfNbTaZr and MoNbTaVW RHEAs vs. SS and Inconel. Most importantly, the erosion and the coating material experimental data show that erosion in sCO2 Brayton Cycles can be eliminated completely if RHEAs are used. The experimental suite and validations confirm that HfNbTaZr is suitable for harsh environments that do not include nuclear radiation, while MoNbTaVW is suitable for harsh environments that include radiation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Tailoring composition and deformation modes at the microstructural level for next generation low-cost high-strength austenitic stainless steels

The objective of this project is to enable deliberate development of cost-effective, hydrogen resistant alloys by establishing detailed relationships specific to the effects of alloy composition, short-range order (SRO), and microsegregation in the presence of hydrogen on the transition between homogeneous deformation and localized plasticity in shear bands. In collaboration with the International Institute for Carbon-Neutral Energy Research, I2CNER, at Kyushu University in Japan, we conceptualized, designed, and manufactured four austenitic alloys that maintain corrosion resistance and ensure lower cost relative to baseline commercial alloys. The mechanical properties and deformation modes of the novel alloys (KU alloys) were assessed in the presence of hydrogen (H). Correlations between composition and performance revealed that two of the KU alloys are suitable replacements for 316 steel, while another is a viable replacement for 304 steel at room temperature. We found that, in the presence of other austenite stabilizing elements namely Mn and N, replacing Ni with Cu does not lead to martensite formation as has been previously reported.1–3 Furthermore, we found that the addition of Cu leads to an earlier onset of multiple slip resulting in an relative earlier onset of a higher work hardening rate (WHR). Greater understanding of the relationships between alloy composition and SRO required the development of a novel advanced electron diffraction methodology to characterize SRO in complex FCC alloys. This innovative approach, which combines fluctuation and correlation analyses of diffuse-scattering signals, successfully differentiated between SRO and long-range ordering (LRO). Further investigations into annealed austenitic stainless steels could provide insights into manipulating SRO and its effects on material properties. Atomistic simulations provided understanding of SRO behavior that was difficult to capture experimentally. This project created the first spin cluster expansion model that is able to capture and describe SRO effects in Fe-Ni-Cr FCC alloys, accounting for the non-negligible effects of magnetism. An automated computational workflow was established to provide reliable predictions of SRO in Fe-Ni-Cr austenitic alloys, both with and without the presence of H atoms. Analysis of the propensity for SRO in Fe-Ni-Cr alloys revealed that H tends to cluster with specific, well-defined SRO domains. The computational framework is general purpose and can be extended to realistic stainless steels across diverse composition ranges. With confidence that SRO is possible in austenitic stainless steels, we developed a discrete dislocation finite element code to understand the interaction of dislocations with SRO in the presence of H. By incorporating H effects on the dislocation emission and SRO stress field we show that the critical stress for the dislocation pileup to breakthrough the SRO domain decreases in the presence of H, which directly contributes localized deformation at the macroscale. Through the simulation of a uniaxial tension test, we demonstrated that H-induced weakening of SRO stress field and H-enhanced dislocation emission can lead to the onset of shear localization at lower macroscopic strains. As a whole, this project identified three novel alloys that show improvements in performance and cost efficiency for H-facing applications by studying correlations between alloy chemistry and deformation behavior. We also made significant advancements to experimental and computational methodologies necessary to study the chemistry and distribution of SRO across a range of alloys, which in turn allowed us to demonstrate how deformation mechanisms change due to the contributions of SRO in austenitic alloys in the presence of H. The combined advancements in fundamental understanding with novel alloy development in this project has increased the viability of next generation H-technologies for the broader public through accessible low-cost alloys and accelerated development towards future H-infrastructure.

08 HYDROGEN↗
DOE OSTI2026

Process-level cost analysis of hybrid manufacturing pathways for aerospace structural components

Hybrid manufacturing is a promising route for producing complex aerospace components, yet systematic cost benchmarking across multiple additive-subtractive pathways remains limited. This study presents a comprehensive process-based cost analysis of seven hybrid manufacturing routes, including laser powder bed fusion (L-PBF), powder- and wire-directed energy deposition (DED), wire arc additive manufacturing (WAAM), additive friction stir deposition (AFSD), metal binder jetting (MBJ), and agility forging, followed by scanning and finish machining. Parametric cost models incorporating direct material, labor, and energy costs were developed. L-PBF results are discussed in detail for a pickle fork component and directly compared with commercial pricing. Across all hybrid routes, labor emerged as the dominant cost driver, contributing more than 70% of total manufacturing cost in some cases. AFSD exhibited the lowest cost for aluminum components, with MBJ being its 316 L stainless steel counterpart, after accounting for geometric scaling. Benchmarking against industrial quotes suggests that hybrid manufacturing can achieve cost levels comparable to those of commercial services, although labor-intensive processes exhibit greater deviation. The analysis highlights automation of material handling, setup, and supervision as key opportunities for improving economic competitiveness. Overall, the proposed framework provides a quantitative basis for evaluating and optimizing hybrid manufacturing pathways for aerospace applications.

Baruah, Sweta [ORNL] (ORCID:0009000174256207)↗
DOE OSTI2025

Evolution of dislocations during the rapid solidification in additive manufacturing

Materials processed by fusion-based additive manufacturing (AM) typically exhibit relatively high dislocation densities, along with cellular structures and elemental segregation. This representative structural feature significantly influences material performance; however, post-mortem microstructure characterizations of AM materials cannot capture the dynamic evolution of dislocations during the manufacturing process, thereby offering limited mechanism-based guidance for further advancing AM techniques and facilitating the qualification and certification of AM products. In this study, we conduct operando high-energy synchrotron X-ray diffraction experiments on wire-laser directed energy deposition of 316 L stainless steel. Through a unique configuration, our operando synchrotron experiments semi-quantitatively probe the dislocation density in solid phases and their dynamic changes during solidification and subsequent cooling. By integrating this advanced synchrotron technique with multi-physics simulation, in-situ neutron diffraction, and multi-scale electron microscopy characterization, our mechanistic study aims to elucidate the effects of rapid cooling and subsequent thermal cycling on the dislocation generation and evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Development of Lightweight Structural Materials with Improved Properties for Fission Batteries

Fission batteries require lightweight structural materials that demonstrate structural resilience when subjected to repeated shutdown, transportation, startup cycles, and certain external conditions, including rare events such as seismic vibrations and tsunamis. The objectives of this project are (1) to produce lightweight structural materials whose strength-to-weight ratios and fatigue resistance exceed those of current widely used structural materials such as 316 stainless steels (SS316), and (2) to enhance radiation tolerance of structural materials over a suitable service temperature range. To achieve these, (1) a lattice structure will be produced, (2) advanced modeling and simulation tools will be employed to design lattice structures (e.g., a gyroid structure) that reduce stress concentrations and thus increase fatigue resistance, and (3) one-dimensional (1-D) carbon nanotubes will be added to enhance radiation resistance. To validate our solution, high-temperature tensile and fatigue testing, in combination with microstructure characterization, will be conducted on wrought materials, additively manufactured solid materials, and the designed lightweight lattice structure material. Ion irradiation, microstructure characterization, and nanoindentation will be carried out to investigate the effect of 1-D carbon nanotubes on radiation tolerance. Successful completion of this project will deliver a material to serve as a substitute for current SS316 using the same chemistry but with lighter weight and improved mechanical properties. In addition, a material with carbon nanotubes can be designed for improved radiation tolerance over a suitable service temperature range. This project will establish new techniques in innovative materials/lattice design, advanced macroscale properties prediction, and the application of state-of-the-art processes.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Microstructural modification of additively manufactured metals by electropulsing

Additive manufacturing (AM) promises rapid development cycles and fabrication of ready-to-use, geometrically-complex parts. The metallic parts produced by AM often contain highly non-equilibrium microstructures, e.g. chemical microsegregation and residual dislocation networks. While such microstructures can enhance some material properties, they are often undesirable. Many AM parts are thus heat-treated after fabrication, a process that significantly slows production. This study investigated if electropulsing, the process of sending high-current-density electrical pulses through a metallic part, could be used to modify the microstructures of AM 316 L stainless steel (SS) and AlSi10Mg parts fabricated by selective laser melting (SLM) more rapidly than thermal annealing. Electropulsing has shown promise as a rapid postprocessing method for materials fabricated using conventional methods, e.g. casting and rolling, but has never been applied to AM materials. For both the materials used in this study, as-fabricated SLM parts contained significant chemical heterogeneity, either chemical microsegregation (316 L SS) or a cellular interdendritic phase (AlSi10Mg). In both cases, annealing times on the order of hours at high homologous temperatures are necessary for homogenization. Using electropulsing, chemical microsegregation was eliminated in 316 L SS samples after 10, 16 ms electrical pulses. In AlSi10Mg parts, electropulsing produced spheroidized Si-rich particles after as few as 15, 16 ms electrical pulses with a corresponding increase in ductility. Finally, this study demonstrated that electropulsing can be used to modify the microstructures of AM metals.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Design Optimization for Printed Melt Wire Arrays Encapsulation

As part of the Nuclear Energy Enabling Technology (NEET) Advanced Sensor and Instrumentation (ASI) Program, Idaho National Laboratory (INL) has recently established in-house capabilities to fabricate and test new advanced-manufactured sensors for measuring peak irradiation temperature within a nuclear test reactor. Although methods of real-time temperature monitoring, such as thermocouples, may be used, the complexity of feedthroughs and attachments to collect real-time measurements greatly increases the cost of the experiment. Instead, passive monitoring techniques may be used for peak- temperature measurement that exploit the melting point of well-characterized materials (standard melt wires) to infer peak reactor temperatures. However, limited available space for instrumentation during experiments introduces an additional challenge. To accommodate this, INL has expanded its temperature- detection instrumentation capabilities to include advanced manufactured (AM) melt wires for peak irradiation temperature measurements. These melt wires can determine peak temperatures while also accommodate space limitations in irradiation experiments. In an effort to improve performance reliability of AM meltwire capabilities, a process was developed and tested to identify the significance of entrapping a high purity inert atmosphere within the packaging of printed melt wire arrays. The materials used in this study were aluminum, zinc, and tin encapsulated in high purity helium within a stainless steel (SS) 316 container. Tin, with a low melting point of approximately 230°C, Zn with a mid-melting point of approximately 420°C, and Al with a high melting point of approximately 660°C. This report describes the design, fabrication process, furnace testing and X-ray Computed Tomography (XCT) evaluation. Results show a successful outcome in creating an inert gas encapsulation and high-resolution evaluation methods.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Preliminary Report on Compositional Specification for Printed 316SS

The Advanced Materials and Manufacturing Technologies Program is focused on accelerating the development and deployment of advanced materials and components fabricated via additive manufacturing (AM). A key challenge for the widespread adoption of AM is the variability in material properties, which can originate from powder feedstock, process parameters, geometry, and the machine. AM powder feedstock compositions are based on those developed for conventional manufacturing. However, the smaller melt pools combined with multiple melt cycles over the course of a build can have substantial effects on the local phase selection resulting from minor batch-to-batch feedstock variability. Therefore, this report focuses on coupling CALPHAD calculations with data mining and visualization to aid the development of compositional specifications for stainless steel 316, an important alloy for nuclear applications and suitable for AM. This work reports that δ-ferrite formation has a stronger dependence on the amount of nickel in the alloy despite nickel being an austenite stabilizer. These findings show the need for exercising a tighter control on the amount of nickel in the alloy compared with the amount of chromium, which is a ferrite stabilizer.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Modeling Nondestructive Defect Detection in Additively Manufactured Metallic Structures for Nuclear Applications

The future of quickly, economically produced metallic nuclear reactor parts with minimal supply-chain dependence lies in Laser Powder Bed Fusion (LPBF) Additive Manufacturing (AM): a 3D printing method involving laser melting and net shaping stainless steel and Inconel metallic powder into a solid structure. However, intrinsic features in LPBF frequently leads to the formation of materials defects, such as pores, within 3D printed structures. As safe long-term use in energy applications requires knowledge of all relevant defects before deployment in a reactor, we must develop methods for nondestructive detection of these defects. We are investigating Pulsed Thermal Tomography (PTT), which is a non-contact nondestructive imaging method scalable to arbitrary structure size. Thermal tomography (TT) is a computational method for 3D spatial reconstruction of material thermal effusivity from flash or pulsed thermography temperature data cube. Thermography data cube consists of 2D surface temperature measurements at different times. The objective of the present work is to investigate limits on defect detection in AM metallic structures with PTT. To this effect, we modeled PTT with COMSOL heat transfer computer simulations. We developed a layered media COMSOL simulation consisting of a Stainless Steel 316 (SS316) plate with an internal layer of un-sintered SS316 powder. Thermophysical properties of the powder layer were modeled with equivalent volume mixing model. To account for partial sintering at the boundary of the defect, the transition between solid and powder layers was modeled as a Gaussian. Using data from COMSOL simulations, we reconstructed depth-dependent thermal effusivity, which allowed defect visibility estimation. A series of parametric studies determined that at 1mm depth, 50µm is the smallest detectable defect. In addition, classification of the defects which can lead to early fatigue of the metallic structure in a reactor is briefly discussed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Characterization of multi-material 316L-Hastelloy X fabricated via laser powder-bed fusion

The aim of this work is to provide firsthand knowledge of 316 L stainless steel (316 L) and Hastelloy X (HX) multi-material processing via laser powder bed fusion (PBF). Specifically, microstructure of the interface is studied using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). Surface metrology is performed to characterize the resulting surface roughness at the interface followed by tensile and flexural testing of multi-material samples to characterize the mechanical properties of the interfaces. Results showed that use of proper process parameters for each individual material led to formation of a compositional gradient at the interface that stretched for 240 μm (10–12 layers) with no evidence of cracking or porosity. The interface exhibited higher surface roughness compared to 316 L or HX as measured by arithmetic mean height, Sa, and maximum valley depth, Sv, parameters. During tensile testing, samples failed in the 316 L region away from the interface, with comparable yield strength, ultimate strength, and ductility. Finally, it was concluded that the “naturally” formed interface created a compositional gradient which was defect free due to similar values of coefficient of thermal expansion, input energy density, and different Marangoni numbers of the materials.

316L stainless Steel↗
DOE OSTI2025

A detailed study of pre-heating effects in electron beam melting powder bed fusion process

Metal-based additive manufacturing processes, such as powder bed fusion with electron beam (PBF-EB) process, also referred to as electron beam melting (EBM), can produce high-density parts with minimal residual stresses due to the uniform and coherent preheating of the powder bed. However, understanding and controlling the multiple stages of preheating is required to enable the production of high-quality, consistent parts of various materials. This work presents a large-scale, multi-layer, three-dimensional numerical analysis focused on studying the preheating stages for predicting thermal history during the PBF-EB process. The model follows a continuous multi-stage cyclic process, that incorporates all the main stages of the PBF-EB process for 316 L stainless steel. This includes the gradual deposition of a new powder layer, the first and second preheating levels of the powder bed, and the energy deposition during melting (excluding the actual melt-pool behavior simulation). The model employs an adaptive time-scaling approach that automatically adjusts the energy deposition for each solution time-increment. This allows for localized changes in time-resolution over an otherwise computationally expensive multi-layer procedure. The material property variations are also taken into account, with an emphasis on the subtle irreversible changes in powder effective thermal conductivity after the two requisite preheating stages of the powder bed. This effect is studied using simplified conductivity models from the literature for partially sintered powder, validated by a dedicated experiment and numerical simulation. The large-scale model is then used to estimate the actual temperatures during first and second preheating levels for 316 L steel, which is not yet fully supported commercially for PBF-EB. Model predictions are corroborated by experiments, using and analyzing IR images, taken at the completion of each layer by the machine’s built-in infrared camera. The current model also incorporates a qualitative assessment for the effects of conductivity change during pre-heating, as well as evaluates the applicability of the time-scaling approach.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Unsupervised learning-enabled pulsed infrared thermographic microscopy of subsurface defects in stainless steel

Metallic structures produced with laser powder bed fusion (LPBF) additive manufacturing method (AM) frequently contain microscopic porosity defects, with typical approximate size distribution from one to 100 microns. Presence of such defects could lead to premature failure of the structure. In principle, structural integrity assessment of LPBF metals can be accomplished with nondestructive evaluation (NDE). Pulsed infrared thermography (PIT) is a non-contact, one-sided NDE method that allows for imaging of internal defects in arbitrary size and shape metallic structures using heat transfer. PIT imaging is performed using compact instrumentation consisting of a flash lamp for deposition of a heat pulse, and a fast frame infrared (IR) camera for measuring surface temperature transients. However, limitations of imaging resolution with PIT include blurring due to heat diffusion, sensitivity limit of the IR camera. We demonstrate enhancement of PIT imaging capability with unsupervised learning (UL), which enables PIT microscopy of subsurface defects in high strength corrosion resistant stainless steel 316 alloy. PIT images were processed with UL spatial–temporal separation-based clustering segmentation (STSCS) algorithm, refined by morphology image processing methods to enhance visibility of defects. The STSCS algorithm starts with wavelet decomposition to spatially de-noise thermograms, followed by UL principal component analysis (PCA), fine-tuning optimization, and neural learning-based independent component analysis (ICA) algorithms to temporally compress de-noised thermograms. The compressed thermograms were further processed with UL-based graph thresholding K-means clustering algorithm for defects segmentation. The STSCS algorithm also includes online learning feature for efficient re-training of the model with new data. For this study, metallic specimens with calibrated microscopic flat bottom hole defects, with diameters in the range from 203 to 76 µm, were produced using electro discharge machining (EDM) drilling. While the raw thermograms do not show any material defects, using STSCS algorithm to process PIT images reveals defects as small as 101 µm in diameter. To the best of our knowledge, this is the smallest reported size of a sub-surface defect in a metal imaged with PIT, which demonstrates the PIT capability of detecting defects in the size range relevant to quality control requirements of LPBF-printed high-strength metals.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Effect of 316 stainless steel powder processing conditions on microstructure

One parameter that has both economic and performance effects in the manufacturing of steel parts is the powder feedstock used. 316 L steel powder can be produced through water atomization or gas atomization, where both the powder size and the atomization process determine the cost of powder feedstock. Gas atomized powder is spherical and has a lower oxygen content than water atomized powder, making it the preferred choice for performance, but comes at a higher financial cost. Here, in this study, various 316 L powder batches are characterized to understand physical properties and microstructural variations. Density and flowability were determined using gas pycnometry and Hall flow tests. Powder morphology and porosity were qualitatively analyzed via optical microscopy and scanning electron microscopy, Finally, transmission electron microscopy was used to determine changes in phases present. Spherical gas atomized powder of 30–100 μm contained Mn$-$Si rich oxides both on the surface and within the matrix. Meanwhile, irregular water atomized powder 30 μm in diameter contained silicon oxides without manganese. All powder particles contained a nickel rich cellular structure which was shown to support the formation of additional phases. While literature has observed general microstructural features across 316 L powder particles, transmission electron microscopy (TEM) in this study has identified variations in precipitation and cell structures. Information regarding morphology, flowability, density, and phase distributions can be applied to understand variations in part consolidation, which will in turn show which powder aspects are significant for production.

Chemical segregation↗
DOE OSTI2023

Accelerated Materials Design for Molten Salt Technologies Using Innovative High-Throughput Methods

The focus of the project is on building an innovative accelerated materials design platform for molten salt technologies using novel high-throughput methods coupled to data analytics. The main objectives is to predict a FeCrMnNi alloy compositional space with better corrosion resistance than stainless steel 316 and identify new molten salt corrosion mechanisms. The project demonstrates the feasibility to use high-throughput methods coupled to data analytics to accelerate alloy design for extreme environments applications. Using a trained and tested machine learning (ML) model, 2000 FeCrMnNi alloy corrosion rate in molten chloride salts were predicted and a compositional field with corrosion rate lower than 316 stainless steel was identified. The ML model interpretability unveiled multiple features of importance in the model prediction. Some features were expected to be of relative significance, such as work function, surface energy and alloy electronegativity, and the ML model interpretability analysis confirmed those. On the other hand, the most important feature is the diffusion coefficient of Ni in the bulk alloy which indicates that a surface diffusion mechanism plays an important role in the overall corrosion mechanism in molten salts.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Heavy ion irradiation response of an additively manufactured 316LN stainless steel

Additive manufacturing has become an appealing technique to fabricate three-dimensional metallic materials and components for nuclear reactors. However, response of additively manufactured alloys to high-dose heavy ion irradiations at elevated temperatures is still not well understood. Here, an additively manufactured 316LN austenitic stainless steel with high-density solidification cells was irradiated using 3.5 MeV Fe ion to a peak dose of 220 dpa at 450 °C. Microscopy studies show a lower Frank loop density and smaller size in the additively manufactured sample compared with its cold worked counterpart, and the cellular structures may largely suppress the formation of perfect loops and dislocation networks and reduce the magnitude of solute segregations comparing with high angle grain boundaries. In conclusion, the present work advances the understanding on the high-temperature irradiation response of additively manufactured steels for nuclear reactor applications.

36 MATERIALS SCIENCE↗