Search NASA⌕ Search

SEARCH · Search NASA

Results for “Analysi”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Statistical Energy Analysis (SEA) and Energy Finite Element Analysis (EFEA) Predictions for a Floor-Equipped Composite Cylinder

Comet Enflow is a commercially available, high frequency vibroacoustic analysis software founded on Energy Finite Element Analysis (EFEA) and Energy Boundary Element Analysis (EBEA). Energy Finite Element Analysis (EFEA) was validated on a floor-equipped composite cylinder by comparing EFEA vibroacoustic response predictions with Statistical Energy Analysis (SEA) and experimental results. Statistical Energy Analysis (SEA) predictions were made using the commercial software program VA One 2009 from ESI Group. The frequency region of interest for this study covers the one-third octave bands with center frequencies from 100 Hz to 4000 Hz.

Grosveld, Ferdinand W.↗
NASA NTRS2018

Parametric Analysis of Aircraft WingWeight Using Low-Order Physics-Based Analysis

In the conceptual aircraft design phase, prediction of the empty weight typically relies on empirically-based regression equations which execute quickly and require little detailed information about the internal structural layout. Since they are based on existing aircraft, however, empirical methods can lose their validity for newer technologies and unconventional configurations. Designers can transition to higher-order, physics-based analysis methods to improve the accuracy of the weight prediction, but at the cost of complex model setup and increased computational time. This paper describes a methodology for low-order aero-structural analysis of conceptual aircraft configurations that increases the use of physics-based analysis in conceptual design, but is less complex and time-consuming than higher-order methods such as finite-element analysis. The methodology uses Vehicle Sketch Pad (OpenVSP) to model the aircraft geometry, and ASWING to perform the aero-structural analysis. The internal forces and moments from the ASWING analysis are post-processed to calculate the resulting direct and shear stresses in the structure, and the thickness distributions of the aircraft components are varied to match the maximum von Mises stress at each cross section to the material allowable. To offset the increased computational time relative to empirical weight equations, a process is studied which uses parametric variation to develop a regression equation relating the weight of the aircraft wing to major design variables. This new weight equation is similar to existing empirical equations, but is built using the more physics-based methodology; the new equation could be used to augment or replace portions of the empirical database to improve the validity of the wing weight prediction for unconventional configurations and advanced technologies.

Olson, Erik D.↗
NASA NTRSDate not supplied

Demonstration of Linear Covariance Analysis Techniques to Evaluate Entry Descent and Landing Guidance Algorithms, Vehicle Configurations, Analysis Techniques, and Trajectory Profiles

Linear covariance analysis techniques have been previously developed to analyze closed-loop entry, descent, and landing (EDL) scenarios and the initial validation efforts are under-way confirming the generated GN&C system performance results. Given both the theoretical foundation and previous conceptual demonstration, this work begins to flex the potential of linear covariance analysis for atmospheric flight and highlight its versatility and reliability by evaluating multiple entry guidance algorithms, vehicle configurations, trajectory profiles, environment conditions, and analysis techniques for a variety of trade studies. To demonstrate the benefit linear covariance analysis can provide in producing rapid yet accurate performance data, two entry profiles are adopted including the NASA Mars Science Laboratory (MSL) and Exploration Flight Test-1 (EFT-1) while utilizing two different guidance algorithms, the Apollo Final Phase (AFP) and the Fully Numeric Predictor-Corrector Entry Guidance (FNPEG) with different navigation sensor suites in a 6 degree-of-freedom (6-DOF) simulation environment. Results are shown using both linear covariance and Monte Carlo analysis techniques to high-light the consistency between the two methodologies and continue the validation maturation of linear covariance analysis for entry, descent, and landing.

EDL↗
DOE OSTI2021

Analysis of PNAR Spent Fuel Safeguards Measurements using the ORIGEN Data Analysis Module

This paper summarizes the analysis of the Passive Neutron Albedo Reactivity (PNAR) measurements using the ORIGEN data analysis module for 23 boiling water reactor spent fuel assemblies that were performed in Finland under an international collaboration on spent fuel safeguards verification methods. PNAR is part of the proposed integrated nondestructive system to be used for safeguards verifications at the planned Finnish encapsulation facility. Besides measuring passive neutron and gamma emission rates from an assembly like a Fork detector, PNAR also measures the PNAR ratio, which is expected to correlate with the fissile content in the assembly. The emission rates and PNAR ratio can be used to verify the operator declarations and the fissile content of an assembly, respectively. The analysis was performed using the ORIGEN Data Analysis Module, which was originally developed for predicting Fork detector neutron and gamma signals for spent fuel measurements and has been integrated into the Integrated Review and Analysis Package developed by Euratom and the IAEA. The Module includes the ORIGEN burnup analysis code and integrates detector response functions pre-generated using MCNP to predict detector signals in several seconds per assembly. In this study, new response functions specific to PNAR measurements were generated for ORIGEN Module. The study also analyzes impacts of using detailed fuel design and operation information vs. standard safeguards information on results calculated by ORIGEN Module. Using detailed information reduced the standard deviation of relative differences between calculated and measured neutron count rates among the 23 assemblies from ~10% to ~4%. The results obtained using standard safeguards information for these PNAR measurements were similar to those obtained for the Fork detector. A clear trend was found between the calculated net neutron multiplications and the measured PNAR ratios of the 23 assemblies. This paper describes how ORIGEN Module calculates the expected PNAR neutron and gamma signals and PNAR ratio and how they compare with corresponding measured values.

Ilas, Germina↗
DOE OSTI2024

Novel principal component analysis tool based on python for analysis of complex spectra of time-of-flight secondary ion mass spectrometry

Time-of-flight secondary ion mass spectrometry (ToF-SIMS) is a powerful surface analysis tool, which can simultaneously provide elemental, isotopic, and molecular information with part per million (ppm) sensitivity. However, each spectrum may be composed of hundreds of ion signals, which makes the spectra data complex. Principal component analysis (PCA) is a multivariate analysis technique that has been widely used to figure out the variances among samples in ToF-SIMS spectra data analysis and is showing great success in the explanation of complex ToF-SIMS spectra. So far, several software tools have been developed for PCA of ToF-SIMS spectra; however, none of them are freely available. Such a situation leads to some difficulties in extending applications of PCA to various research fields. More importantly, it has long been challenging for common researchers to understand PCA plots and extract chemical differences among samples. In this work, we developed a new and flexible software tool (named “advanced spectra pca toolbox”) based on python for PCA of complex ToF-SIMS spectra along with an easy-to-read manual. It can generate data analysis reports automatically to explain chemical differences among samples, allowing less experienced researchers to easily understand tricky PCA results. Moreover, it is expandable and compatible with artificial intelligence/machine learning functions. Pure goethite and different lignin adsorbed goethite samples were used as a model system to demonstrate our new software tool, proving that our software tool can be readily used in complex spectra data processing. Our new software tool is open-source, convenient, flexible, and expandable. We expect this open-source tool will benefit the ToF-SIMS community.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Real‐time XFEL data analysis at SLAC and NERSC: A trial run of nascent exascale experimental data analysis

X‐ray scattering experiments using free electron lasers (XFELs) are a powerful tool to determine the molecular structure and function of unknown samples (such as COVID‐19 viral proteins). XFEL experiments are a challenge to computing in two ways: (i) due to the high cost of running XFELs, a fast turnaround time from data acquisition to data analysis is essential to make informed decisions on experimental protocols; (ii) data‐collection rates are growing exponentially, requiring new scalable algorithms. Here we report our experiences analyzing data from two experiments at the Linac Coherent Light Source (LCLS) during September 2020. Raw data were analyzed on NERSC's Cori XC40 system, using the Superfacility paradigm: our workflow automatically moves raw data between LCLS and NERSC, where it is analyzed using the software package CCTBX. We achieved real time data analysis with a turnaround time from data acquisition to full molecular reconstruction in as little as 10 min—sufficient time for the experiment's operators to make informed decisions. By hosting the data analysis on Cori, and by automating LCLS‐NERSC interoperability, we achieved a data analysis rate which matches the data acquisition rate. Completing data analysis within 10 min is a first for XFEL experiments and an important milestone if we are to keep up with data‐collection trends.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

Elemental analysis of air-sensitive frozen molten salt samples using an inert transfer chamber for LIBS/LA-ICP-TOF-MS analysis

A novel inert sample transfer system was developed and employed to enable, for the first time, the analysis of air-sensitive salt samples in a two-volume ablation cell using simultaneous laser-induced breakdown spectroscopy (LIBS) and laser ablation (LA)-inductively coupled plasma (ICP)-time-of-flight (TOF)-mass spectrometry (MS) analysis. Molten salts are of growing interest as a medium for advanced nuclear reactors and nuclear fuel reprocessing technologies continue to be developed around their use. However, compositional analysis of molten salt samples can be challenging because of their air-sensitive nature and varying solubilities leading to inaccurate measurements when digested. LA-based analysis provides an alternate method to digestion and can provide rapid elemental information with little sample preparation. In this study, LIBS and LA-ICP-TOF-MS were used to analyze the Ce content in frozen salt samples taken from a series of electrochemical experiments. Calibrations were built for each technique, and the resulting limits of detection for Ce were estimated to be 107 and 58 µg g −1 for LIBS and LA-ICP-TOF-MS, respectively. Test samples from the electrochemical experiments were analyzed using these calibrations. The results matched bulk digestion-based ICP-optical emission spectroscopy values, and daily trends in Ce concentration changes were identified. Additionally, the LIBS and LA-ICP-TOF-MS analysis was demonstrated for identifying microgram per gram levels of components and detecting trace contaminants. The impurities detected by LIBS included Al, Mg, Ca, and Na. The impurities detected by LA-ICP-TOF-MS included W, Ag, Al, Fe, Ni, Mo, Nd, Sm, Th, and U.

Andrews, Hunter B. [Oak Ridge National Laboratory ↗
NASA NTRS1985

Analysis of flexible aircraft longitudinal dynamics and handling qualities. Volume 1: Analysis methods

As aircraft become larger and lighter due to design requirements for increased payload and improved fuel efficiency, they will also become more flexible. For highly flexible vehicles, the handling qualities may not be accurately predicted by conventional methods. This study applies two analysis methods to a family of flexible aircraft in order to investigate how and when structural (especially dynamic aeroelastic) effects affect the dynamic characteristics of aircraft. The first type of analysis is an open loop model analysis technique. This method considers the effects of modal residue magnitudes on determining vehicle handling qualities. The second method is a pilot in the loop analysis procedure that considers several closed loop system characteristics. Volume 1 consists of the development and application of the two analysis methods described above.

Waszak, M. R.↗
NASA NTRS1987

Power flow as a complement to statistical energy analysis and finite element analysis

Present methods of analysis of the structural response and the structure-borne transmission of vibrational energy use either finite element (FE) techniques or statistical energy analysis (SEA) methods. The FE methods are a very useful tool at low frequencies where the number of resonances involved in the analysis is rather small. On the other hand SEA methods can predict with acceptable accuracy the response and energy transmission between coupled structures at relatively high frequencies where the structural modal density is high and a statistical approach is the appropriate solution. In the mid-frequency range, a relatively large number of resonances exist which make finite element method too costly. On the other hand SEA methods can only predict an average level form. In this mid-frequency range a possible alternative is to use power flow techniques, where the input and flow of vibrational energy to excited and coupled structural components can be expressed in terms of input and transfer mobilities. This power flow technique can be extended from low to high frequencies and this can be integrated with established FE models at low frequencies and SEA models at high frequencies to form a verification of the method. This method of structural analysis using power flo and mobility methods, and its integration with SEA and FE analysis is applied to the case of two thin beams joined together at right angles.

Cuschieri, J. M.↗
NASA NTRS1992

Methodology for sensitivity analysis, approximate analysis, and design optimization in CFD for multidisciplinary applications

Fundamental equations of aerodynamic sensitivity analysis and approximate analysis for the two dimensional thin layer Navier-Stokes equations are reviewed, and special boundary condition considerations necessary to apply these equations to isolated lifting airfoils on 'C' and 'O' meshes are discussed in detail. An efficient strategy which is based on the finite element method and an elastic membrane representation of the computational domain is successfully tested, which circumvents the costly 'brute force' method of obtaining grid sensitivity derivatives, and is also useful in mesh regeneration. The issue of turbulence modeling is addressed in a preliminary study. Aerodynamic shape sensitivity derivatives are efficiently calculated, and their accuracy is validated on two viscous test problems, including: (1) internal flow through a double throat nozzle, and (2) external flow over a NACA 4-digit airfoil. An automated aerodynamic design optimization strategy is outlined which includes the use of a design optimization program, an aerodynamic flow analysis code, an aerodynamic sensitivity and approximate analysis code, and a mesh regeneration and grid sensitivity analysis code. Application of the optimization methodology to the two test problems in each case resulted in a new design having a significantly improved performance in the aerodynamic response of interest.

Taylor, Arthur C., III↗
NASA NTRS1992

Asymptotic modal analysis and statistical energy analysis

Asymptotic Modal Analysis (AMA) is a method which is used to model linear dynamical systems with many participating modes. The AMA method was originally developed to show the relationship between statistical energy analysis (SEA) and classical modal analysis (CMA). In the limit of a large number of modes of a vibrating system, the classical modal analysis result can be shown to be equivalent to the statistical energy analysis result. As the CMA result evolves into the SEA result, a number of systematic assumptions are made. Most of these assumptions are based upon the supposition that the number of modes approaches infinity. It is for this reason that the term 'asymptotic' is used. AMA is the asymptotic result of taking the limit of CMA as the number of modes approaches infinity. AMA refers to any of the intermediate results between CMA and SEA, as well as the SEA result which is derived from CMA. The main advantage of the AMA method is that individual modal characteristics are not required in the model or computations. By contrast, CMA requires that each modal parameter be evaluated at each frequency. In the latter, contributions from each mode are computed and the final answer is obtained by summing over all the modes in the particular band of interest. AMA evaluates modal parameters only at their center frequency and does not sum the individual contributions from each mode in order to obtain a final result. The method is similar to SEA in this respect. However, SEA is only capable of obtaining spatial averages or means, as it is a statistical method. Since AMA is systematically derived from CMA, it can obtain local spatial information as well.

Dowell, Earl H.↗
NASA NTRS1991

Finite-element analysis and multibody dynamics issues in rotorcraft dynamic analysis

There is general agreement that the development of effective rotorcraft analysis software will require the use of modern computational mechanics methodologies, especially finite element analysis and multibody dynamics. This paper examines the analysis of rotorcraft dynamics from the perspective of these methodologies. First, a general discussion of rotorcraft analysis and modeling is presented. Then, a hierarchy of rotorcraft analyses is presented, ranging from simple to complex kinematics, where it is shown that in comprehensive rotorcraft software, finite element analysis must be augmented by multibody dynamics in order to properly analyze large motions of rotorcraft components. Finally, a review of multibody dynamics is presented to further familiarize the rotorcraft community with this technology.

Ruzicka, Gene C.↗
NASA NTRS1992

Methods of periodicity analysis - Relationship between the Rayleigh analysis and a maximum likelihood method

For periodicity analysis of occurrence rates of discrete events, one can use the maximum likelihood method or the 'Rayleigh analysis'. In a maximum likelihood analysis using a sinusoidal distribution, one tries various values of amplitude A and phase angle Theta(0) of the distribution function. We show that these two methods are essentially equivalent to one another in spite of their different mathematical origins. Using the Rayleigh analysis, therefore, we can simply calculate A and Theta(0) which maximize the likelihood. Using the cumulative nature of the logarithmic likelihood, we can identify time intervals during which the periodicity is in operation. When a periodicity operates only in certain time intervals, it is important to identify these intervals. Mathematically, the above technique is applicable only to discrete events. However, with slight modifications we can apply this technique to general cases - periodicity analysis of measurements of continuously varying quantities.

Bai, T.↗
NASA NTRS1995

Bearing defect signature analysis using advanced nonlinear signal analysis in a controlled environment

Utilizing high-frequency data from a highly instrumented rotor assembly, seeded bearing defect signatures are characterized using both conventional linear approaches, such as power spectral density analysis, and recently developed nonlinear techniques such as bicoherence analysis. Traditional low-frequency (less than 20 kHz) analysis and high-frequency envelope analysis of both accelerometer and acoustic emission data are used to recover characteristic bearing distress information buried deeply in acquired data. The successful coupling of newly developed nonlinear signal analysis with recovered wideband envelope data from accelerometers and acoustic emission sensors is the innovative focus of this research.

Zoladz, T.↗
NASA NTRS2003

Combining Static Analysis and Model Checking for Software Analysis

We present an iterative technique in which model checking and static analysis are combined to verify large software systems. The role of the static analysis is to compute partial order information which the model checker uses to reduce the state space. During exploration, the model checker also computes aliasing information that it gives to the static analyzer which can then refine its analysis. The result of this refined analysis is then fed back to the model checker which updates its partial order reduction. At each step of this iterative process, the static analysis computes optimistic information which results in an unsafe reduction of the state space. However we show that the process converges to a fired point at which time the partial order information is safe and the whole state space is explored.

Brat, Guillaume↗
NASA NTRS2005

Structural Analysis for the American Airlines Flight 587 Accident Investigation: Global Analysis

NASA Langley Research Center (LaRC) supported the National Transportation Safety Board (NTSB) in the American Airlines Flight 587 accident investigation due to LaRC's expertise in high-fidelity structural analysis and testing of composite structures and materials. A Global Analysis Team from LaRC reviewed the manufacturer s design and certification procedures, developed finite element models and conducted structural analyses, and participated jointly with the NTSB and Airbus in subcomponent tests conducted at Airbus in Hamburg, Germany. The Global Analysis Team identified no significant or obvious deficiencies in the Airbus certification and design methods. Analysis results from the LaRC team indicated that the most-likely failure scenario was failure initiation at the right rear main attachment fitting (lug), followed by an unstable progression of failure of all fin-to-fuselage attachments and separation of the VTP from the aircraft. Additionally, analysis results indicated that failure initiates at the final observed maximum fin loading condition in the accident, when the VTP was subjected to loads that were at minimum 1.92 times the design limit load condition for certification. For certification, the VTP is only required to support loads of 1.5 times design limit load without catastrophic failure. The maximum loading during the accident was shown to significantly exceed the certification requirement. Thus, the structure appeared to perform in a manner consistent with its design and certification, and failure is attributed to VTP loads greater than expected.

Young, Richard D.↗
NASA NTRS2012

An Analysis Technique/Automated Tool for Comparing and Tracking Analysis Modes of Different Finite Element Models

An analysis technique was developed to compare and track mode shapes for different Finite Element Models. The technique may be applied to a variety of structural dynamics analyses, including model reduction validation (comparing unreduced and reduced models), mode tracking for various parametric analyses (e.g., launch vehicle model dispersion analysis to identify sensitivities to modal gain for Guidance, Navigation, and Control), comparing models of different mesh fidelity (e.g., a coarse model for a preliminary analysis compared to a higher-fidelity model for a detailed analysis) and mode tracking for a structure with properties that change over time (e.g., a launch vehicle from liftoff through end-of-burn, with propellant being expended during the flight). Mode shapes for different models are compared and tracked using several numerical indicators, including traditional Cross-Orthogonality and Modal Assurance Criteria approaches, as well as numerical indicators obtained by comparing modal strain energy and kinetic energy distributions. This analysis technique has been used to reliably identify correlated mode shapes for complex Finite Element Models that would otherwise be difficult to compare using traditional techniques. This improved approach also utilizes an adaptive mode tracking algorithm that allows for automated tracking when working with complex models and/or comparing a large group of models.

Towner, Robert L.↗
NASA NTRS2019

Analysis Ready Data in Analytics Optimized Data Stores for Analysis of Big Earth Data in the Cloud

Cloud computing offers the possibility of making the analysis of Big Data approachable for a wider community due to affordable access to computing power, an ecosystem of usable tools for parallel processing, and migration of many large datasets to archives in the cloud, allowing data-proximal computing. Generally, data analysis acceleration in the cloud comes from running multiple nodes in a split-combine-apply strategy. Data systems such as the Earth Observing System Data and Information System are in a position to "pre-split" the data by storing them in a data store that is optimized for data parallel computing, i.e., an Analytics-Optimized Data Store (AODS). A variety of approaches to AODS are possible, from highly scalable databases to scalable filesystems to data formats optimized for cloud access (e.g., zarr and cloud-optimized datasets), with the optimal choice dependent on both the types of analysis and the geospatial structure of the data. A key question is how much preprocessing of the data to do, both before splitting and as the first part of the apply step. Again, the geospatial structure of the data and the analysis type influence the decision, with the added complexity of the user type. Trans-disciplinary users who are not well-versed in the nuances of quality-filtering and georeferencing of remote sensing orbit/swath/scene data tend to ask for more highly processed data, relying on the data provider to make sensible decisions on preprocessing parameters. (This accounts for the popularity of "Level 3" gridded data, despite the lower spatial resolution it provides.) In this case, data can be preprocessed before the split, resulting in higher performance in the rest of the "apply" step, which can be transformative for use cases such as interactive data exploration at scale. Discipline researchers who are experienced with remote sensing data often prefer more flexibility in customizing the preprocessing data into Analysis Ready Data, resulting in more need for on-the-fly preprocessing.

Lynnes, Christopher↗