Results for “Annealing temperature” — Page 4

DOE OSTI2023

α-Quartz Phase Stabilization, Surface Texturing, and Tunable Optical Properties of Nanocrystalline GeO 2 Films Made by Pulsed-Laser Deposition: Implications for Optical and Optoelectronic Applications

Germanium oxide (GeO 2 ) has great potential in multifunctional devices and next-generation power electronics due to its high thermal conductivity and ambipolar doping capability. However, the complexity of synthesizing the desirable polymorph with a controlled phase, surface/interface quality, microstructure, and functional properties is the main barrier to GeO 2 utilization in advanced applications. Here, in this regard, we present a method to realize the hexagonal (h) or a-quartz type GeO 2 with nano-textured surface morphology on sapphire substrates using a hybrid synthesis strategy that comprises pulsed laser deposition (PLD) and post-deposition thermal annealing. We performed a comprehensive study to investigate the effect of annealing temperature, which was varied in a wide range (600-1100 °C), on the crystal structure, phase, surface morphology, chemical stoichiometry, defect states, and optical properties of PLD-grown GeO 2 films. As-deposited GeO 2 films at 500 °C were amorphous. Upon annealing, the GeO 2 films induced an amorphous-to-crystalline phase transformation; GeO 2 films annealed at higher annealing temperatures (≥900 °C) stabilized in the hexagonal phase and demonstrated excellent crystal quality and chemical stability. Thermally activated growth process showed increased average crystallite size, which was varied in the range of 20-130 (±2) nm, while the surface roughness followed a similar trend. The spectral transmittance and band gap also increased with increasing annealing temperature. The resulting h-GeO 2 films, particularly those obtained at annealing temperatures in the 900-1100 °C range, had a higher band gap of 6.2-6.3 eV and displayed excellent optical transmittance in the visible region. Moreover, the absence of extended valence band maxima and reduced optical defect density support the quality improvement upon annealing. When considering phase-pure bulk and nanostructured GeO 2 as a possible candidate for ultra wide band gap semiconductors in cutting-edge technological applications, the results of the current work can be beneficial to realize high structural and optical quality a-quartz structured GeO 2 films.

GeO2↗

DOE OSTI2020

Isolating p- and n-Doped Fingers With Intrinsic Poly-Si in Passivated Interdigitated Back Contact Silicon Solar Cells

Polycrystalline silicon on silicon oxide (poly-Si/SiO x ) passivating contacts enable ultra high efficiency interdigitated back contact silicon solar cells. To prevent shunt between n- and p-type doped fingers, an insulating region is required between them. We evaluate the use of intrinsic poly Si for this isolation region. Interdigitated fingers were formed by plasma deposition of doped hydrogenated amorphous silicon through mechanically aligned shadow masks, on top of a full-area intrinsic amorphous silicon layer. High temperature annealing then crystallized the a-Si:H to poly Si and drove in the dopants. Two mechanisms were identified which cause contamination of the intrinsic poly Si gap during processing. During deposition of doped fingers, we show using secondary ion mass spectrometry and conductivity measurements that the intrinsic gap becomes contaminated by doped a-Si:H tails several nanometers thick to concentrations of ~10 20 cm -3 . Another source of contamination occurs during high-temperature annealing, where dopants desorb from doped regions and readsorb onto intrinsic a Si:H. Both pathways reduce the resistivity of the intrinsic gap from ~10 5 Ω·cm to ~10 -1 Ω·cm. We show that plasma etching of the a-Si:H surface before crystallizing with a capping layer can eliminate the contamination of the intrinsic poly-Si, maintaining a resistivity of ~10 5 Ω·cm. Lastly, this demonstrates masked plasma deposition as a dopant patterning method for Si solar cells.

14 SOLAR ENERGY↗

DOE OSTI2025

Internal-Gelation Production of Uranium Oxide Sol-Gel Particles for Forensic Applications

The purpose of this project was to develop and demonstrate a novel method for the production of uranium oxide microsphere particles with tunable chemical compositions via a sol-gel process using a 3D-printer setup. These particles can serve several purposes in research and development as a forensic training tool or as standard reference materials. A key component of the project was to demonstrate the ability to control physical and chemical parameters of the particles created. First, we demonstrated the ability to employ an internal gelation sol-gel process to create individual uranium oxide particles. The particles were successfully dispensed using a unique 3D-printing setup onto a substrate to react and then were collected and thermally processed. A series of temperatures for the annealing process was tested on individual samples to investigate the effect on the sol-gel chemical composition and physical integrity. Next, we demonstrated the ability to control matrix composition of the particles by separately incorporating fission product isotopes as well as Np-237 into the sol-gel solution. It was shown by gamma-ray spectroscopy that these matrix elements were successfully retained during the gelation process. We studied the retention of the elements across a series of annealing temperatures. Additionally, we demonstrated the ability to quantitatively control the isotopic composition of the particles by altering the U-237/U-238 ratio to a controlled value. Finally, X-ray diffraction analysis (XRD) was used to investigate the oxidation state of the sol-gel after annealing at different temperatures.

37 - INORGANIC, ORGANIC, PHYSICAL AND ANALYTICAL C↗

DOE OSTI2019

Enhancing the local conductivity of Cu films using temperature-assisted agglomerated Cu nanostructures

We investigate the structural and electrical properties of Cu film and reveal their changes as a function of post-annealing temperature. Thermal annealing of a Cu film on a dielectric substrate can improve its crystallinity; however, high-temperature annealing also leads to a morphological transformation that hinders the precise measurement of electrical properties. The enhanced crystallinity of the Cu films is verified with x-ray diffraction as the annealing temperature increases. To examine the electrical properties of the Cu film after the dewetting processes, which promotes the formation of voids and agglomerations, we utilize both conventional micro four-point probe method as well as an advanced four-point probe scanning tunneling microscopy (4P-STM) technique to measure the conductance and evolution of the microscopic structural properties. We could eliminate a deceptive effect of voids with 4P-STM technique, and disclosed a significantly reduced resistivity (1.88 ± 0.07 µΩ∙cm) of Cu nanostructure after post-annealing at 700 °C. We unveiled impact of crystallinity and imperfections of Cu nanostructure, and discussed the critical role of the twin grain boundaries of single-crystalline Cu (1 1 1) on an Al 2 O 3 substrate. We anticipate that understanding the evolution of the structures and the enhanced electrical properties of the post-annealed Cu nanostructures would be important for nanoscale devices where Cu is used as an interconnecting material and could provide a new route to control the plasmonic applications.

36 MATERIALS SCIENCE↗

NASA NTRS1989

Sequentially evaporated thin Y-Ba-Co-O superconducting films on microwave substrates

The development of high T sub c superconducting thin films on various microwave substrates is of major interest in space electronic systems. Thin films of YBa2Cu3O(7-Delta) were formed on SrTiO3, MgO, ZrO2 coated Al2O3, and LaAlO3 substrates by multi-layer sequential evaporation and subsequent annealing in oxygen. The technique allows controlled deposition of Cu, BaF2 and Y layers, as well as the ZrO buffer layers, to achieve reproducibility for microwave circuit fabrication. The three layer structure of Cu/BaF2/Y is repeated a minimum of four times. The films were annealed in an ambient of oxygen bubbled through water at temperatures between 850 C and 900 C followed by slow cooling (-2 C/minute) to 450 C, a low temperature anneal, and slow cooling to room temperature. Annealing times ranged from 15 minutes to 5 hrs. at high temperature and 0 to 6 hr. at 450 C. Silver contacts for four probe electrical measurements were formed by evaporation followed with an anneal at 500 C. The films were characterized by resistance-temperature measurements, energy dispersive X-ray spectroscopy, X-ray diffraction, and scanning electron microscopy. Critical transition temperatures ranged from 30 K to 87 K as a function of the substrate, composition of the film, thicknesses of the layers, and annealing conditions. Microwave ring resonator circuits were also patterned on these MgO and LaAlO3 substrates.

Valco, G. J.↗

DOE OSTI2020

Dynamic behavior of reversible oxygen migration in irradiated-annealed high temperature superconducting wires

Large-scale extrusion-based additive manufacturing of high-performance thermoplastic composites like fiber reinforced polyphenylene sulfide (PPS) is well-suited for tooling applications to lower manufacturing costs and lead times. Autoclave tooling requires good mechanical performance at temperatures even above the glass transition temperature (T g ). In this work, the authors have investigated a post-process isothermal annealing technique to improve the mechanical properties of various grades of carbon fiber reinforced PPS components printed on the Big Area Additive Manufacturing (BAAM) system. Since PPS is a semi-crystalline polymer, crystallinity can change during annealing and affect the mechanical properties of the part. In addition, isothermal annealing can also lead to solid-state structural changes in the form of thermal and oxidative branching and/or crosslinking reactions in some grades of PPS which can alter the crystallization process. This work reports the effect of annealing on dynamic mechanical properties of BAAM printed components, along with studies to determine the effect of annealing on crystallinity and the occurrence of oxidative reactions. Results showed that isothermal annealing at 250 °C for 18 h improved the storage modulus of all selected grades (neat and reinforced) of PPS at temperatures above T g . Annealing led to an overall increase in the degree of crystallinity, with secondary crystallization taking place. Although oxidative structural changes were observed to occur more on the surface of the PPS parts, they primarily influenced the size of crystals formed and did not significantly alter the degree of crystallinity at various regions within the sample.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Microstructural and micro-mechanical analysis of 14YWT nanostructured Ferritic alloy after varying thermo-mechanical processing paths into tubing

Microstructural analyses and micro-pillar compression were conducted on 14YWT nanostructured ferritic alloy (NFA) to compare different processing pathways: hydrostatic extrusion and Pilger processing with varying annealing temperatures into thin walled tubing, and after hot extrusion and cross-rolling into a plate. Hydrostatic extrusion at 815 °C resulted in the smallest grain sizes and highest yield strength of 1.20 GPa. Pilger processing with annealing at 800 °C had fine grained regions and bands of coarse grains, leading to a large variation in yield strength of 0.9–1.40 GPa. Higher annealing temperatures of 1200 °C after pilger processing significantly increased the grain size and lowered the yield strength to 1.01 GPa. These tubes showed a stronger (111) crystallographic texture in the normal direction and elongated grains in the extrusion direction. Characterization of the nano-oxides using TEM reveals more numerous, smaller oxides present in tubing processed at lower temperatures. Overall, this work shows NFA tubing after hydrostatic extrusion and pilger processing can lead to fine grained microstructures and texturing leading to higher yield strengths at lower annealing temperatures (e.g. 800 °C).

14YWT↗

DOE OSTI2024

Thermal stability of 3D interface Cu/Nb nanolaminates

Nanocrystalline alloys are promising structural materials yet lack thermal stability in many cases. Recent work shows that interface structure has an outsize effect on the thermal behavior of nanostructured alloys. Here, this work focuses on the role of controlled heterophase interface structure in the thermal evolution of model Cu/Nb nanolaminates. We introduce 3D interfaces containing nanoscale heterogeneities in all spatial dimensions between Cu and Nb, forming 3D Cu/Nb. TEM, nanoindentation, and DSC are used in tandem to establish thermal stability and to identify shifts in microstructure as a function of static annealing temperature. 3D interfaces are shown to survive annealing to 300 °C for 1 hr., while 3D Cu/Nb microstructure evolves to form low-density and voided regions correlating to the onset of layer pinch-off between 500 and 600 °C annealing temperatures. A diffusivity- and vacancy energetics-based mechanism is developed to explain void formation driven by 3D interface degradation at elevated temperature.

3D interfaces↗

DOE OSTI2021

Imaging CdCl 2 defect passivation and formation in polycrystalline CdTe films by cathodoluminescence

Polycrystalline thin-film solar cells are attractive for low-cost photovoltaics, but their efficiencies are hindered by material quality issues. State-of-the-art CdTe solar cells use CdCl 2 annealing treatments whose effects are still being discovered at a fundamental level. Here, a series of CdTe samples with different annealing temperatures is investigated with high-resolution hyperspectral cathodoluminescence mapping measured at both room temperature and low temperature on the same microscopic areas. A statistical analysis over a large number of grains is combined with a local analysis at grain boundaries. The results elucidate the dynamic interplay between grain boundary and intragrain defect passivation and formation, in the midst of grain growth. The CdCl 2 annealing initially contributes to an increase of the grain size and the passivation of both grain boundaries and grain interiors, increasing the overall luminescence and diffusion length. For higher annealing temperatures, a further increase of grain size is counterbalanced by the rise of bulk defects. The results illustrate the tradeoffs that lead to an optimal annealing temperature, as well as new methods for understanding defect passivation and creation in thin film solar cells.

14 SOLAR ENERGY↗

DOE OSTI2025

Identifying the connections between grain growth and flux expulsion in low RRR niobium SRF cavities

The SRF community has shown that high temperature annealing can improve the flux expulsion of niobium cavities during cooldown. The required temperature will vary between cavities and different batches of material, typically around 800 C and up to 1000 C. However, for niobium with a low residual resistance ratio (RRR), even 1000 C is not enough to improve its poor flux expulsion. The purpose of this study is to observe the grain growth behavior of low RRR niobium coupons subjected to high temperature annealing to identify the mechanism for improving flux expulsion. We observe that low RRR material experiences less grain growth than high RRR when annealed at the same temperature. We search for the limitations to grain growth in low RRR material and develop a diagnostic based on grain structure to determine the appropriate recipe for good flux expulsion. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

DOE OSTI2025

Identifying the Connections between Grain Growth and Flux Expulsion in Low RRR Niobium SRF Cavities

The SRF community has shown that high temperature annealing can improve the flux expulsion of niobium cavities during cooldown. The required temperature will vary between cavities and different batches of material, typically around 800 C and up to 1000 C. However, for niobium with a low residual resistance ratio (RRR), even 1000 C is not enough to improve its poor flux expulsion. The purpose of this study is to observe the grain growth behavior of low RRR niobium coupons subjected to high temperature annealing to identify the mechanism for improving flux expulsion. We observe that low RRR material experiences less grain growth than high RRR when annealed at the same temperature. We search for the limitations to grain growth in low RRR material and develop a diagnostic based on grain structure to determine the appropriate recipe for good flux expulsion. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.

Howard, Katrina N. [Chicago U.] (ORCID:00000003256↗

DOE OSTI2025

Identifying the Connections between Grain Growth and Flux Expulsion in Low RRR Niobium SRF Cavities

The SRF community has shown that high temperature annealing can improve the flux expulsion of niobium cavities during cooldown. The required temperature will vary between cavities and different batches of material, typically around 800 C and up to 1000 C. However, for niobium with a low residual resistance ratio (RRR), even 1000 C is not enough to improve its poor flux expulsion. The purpose of this study is to observe the grain growth behavior of low RRR niobium coupons subjected to high temperature annealing to identify the mechanism for improving flux expulsion. We observe that low RRR material experiences less grain growth than high RRR when annealed at the same temperature. We search for the limitations to grain growth in low RRR material and develop a diagnostic based on grain structure to determine the appropriate recipe for good flux expulsion. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.

Howard, Katrina [Chicago U.] (ORCID:00000003256133↗

DOE OSTI2026

Identifying the connections between grain growth and flux expulsion in low RRR niobium SRF cavities

The SRF community has shown that high temperature annealing can improve the flux expulsion of niobium cavities during cooldown. The required temperature will vary between cavities and different batches of material, typically around 800 C and up to 1000 C. However, for niobium with a low residual resistance ratio (RRR), even 1000 C is not enough to improve its poor flux expulsion. The purpose of this study is to observe the grain growth behavior of low RRR niobium coupons subjected to high temperature annealing to identify the mechanism for improving flux expulsion. We observe that low RRR material experiences less grain growth than high RRR when annealed at the same temperature. We search for the limitations to grain growth in low RRR material and develop a diagnostic based on grain structure to determine the appropriate recipe for good flux expulsion. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.

Howard, K. [Chicago U.] (ORCID:0000000325613308)↗

DOE OSTI2026

Understanding the connections between grain growth and flux expulsion in low RRR niobium SRF cavities

The SRF community has shown that high temperature annealing can improve the flux expulsion of niobium cavities during cooldown. The required temperature will vary between cavities and different batches of material, typically around 800 C and up to 1000 C. However, for niobium with a low residual resistance ratio (RRR), even 1000 C is not enough to improve its poor flux expulsion. The purpose of this study is to observe the grain growth behavior of low RRR niobium coupons subjected to high temperature annealing to identify the mechanism for improving flux expulsion in low RRR cavities. We anneal the low RRR material up to 1200 C to understand the limits of flux expulsion performance. We observe that low RRR material experiences less grain growth than high RRR when annealed at the same temperature. We search for the limitations to grain growth in low RRR material and develop a diagnostic based on grain structure to determine the appropriate recipe for good flux expulsion. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.

Howard, K. [Chicago U.]↗

DOE OSTI2025

Identifying the connections between grain growth and flux expulsion in low RRR niobium SRF cavities

The SRF community has shown that high temperature annealing can improve the flux expulsion of niobium cavities during cooldown. The required temperature will vary between cavities and different batches of material, typically around 800 C and up to 1000 C. However, for niobium with a low residual resistance ratio (RRR), even 1000 C is not enough to improve its poor flux expulsion. The purpose of this study is to observe the grain growth behavior of low RRR niobium coupons subjected to high temperature annealing to identify the mechanism for improving flux expulsion. We observe that low RRR material experiences less grain growth than high RRR when annealed at the same temperature. We search for the limitations to grain growth in low RRR material and develop a diagnostic based on grain structure to determine the appropriate recipe for good flux expulsion. The results of this study have the potential to unlock a new understanding on SRF materials and enable the next generation of high Q/high gradient surface treatments.

Howard, K. [Chicago U.] (ORCID:0000000325613308)↗

DOE OSTI2024

Exploring Structural Anisotropy in Amorphous Tb-Co via Changes in Medium-Range Ordering

Amorphous thin films grown by magnetron co-sputtering exhibit changes in atomic structure with varying growth and annealing temperatures. Structural variations influence the bulk properties of the films. Scanning nanodiffraction performed in a transmission electron microscope (TEM) is applied to amorphous Tb 17 Co 83 (a-Tb-Co) films deposited over a range of temperatures to measure relative changes in medium-range ordering (MRO). These measurements reveal an increase in MRO with higher growth temperatures and a decrease in MRO with higher annealing temperatures. The trend in MRO indicates a relationship between the growth conditions and local atomic ordering. By tilting select films, the TEM measures variations in the local atomic structure as a function of orientation within the films. The findings support claims that preferential ordering along the growth direction results from temperature-mediated adatom configurations during deposition, and that oriented MRO correlates with increased structural anisotropy, explaining the strong growth-induced perpendicular magnetic anisotropy found in rare earth–transition metal films. Beyond magnetic films, we propose the tilted FEM workflow as a method of extracting anisotropic structural information in a variety of amorphous materials with directionally dependent bulk properties, such as films with inherent bonding asymmetry grown by physical vapor deposition.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Study on the continuous phase evolution and physical properties of gas-atomized high-entropy alloy powders

In this study, AlCoCrFeNi high entropy alloy (HEA) powders were fabricated by gas atomization process, and the effects of annealing heat treatment on phase evolution and mechanical properties were investigated. The as-atomized powders have pure BCC phase with a spherical shape and equal composition distribution, and then the FCC and sigma phase sequentially generated after annealing. The mechanical property such as hardness was evidently enhanced, which was caused by precipitation hardening effect. After the raw powders were annealed at 600 °C, the FCC (Al–Ni) phase began to precipitate, the its phase intensity raised with the annealing temperature. Then, the sigma phase (Fe– Cr)formed as the annealing temperature reached 800 °C. Both mechanical properties and lattice constant were influenced by heating effect. According to the results, the lattice became loose with the increasing temperature. In summary, the mechanical properties and phase constitutions of gasatomized AlCoCrFeNi HEA powders can be adjusted via annealing process, resulting in precipitation hardening effect.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2023

Nb3Sn Coating of Twin Axis Cavity and Other Complex SRF Cavity Structures

In the field of Accelerator Science, for the low cost and increased quality factor, thin films coated niobium cavities are used in the modern SRF research. Within the potential substances, Nb3Sn has shown higher critical temperature than niobium. Here the tin vapor diffusion method is used as the preferred technique to coat niobium cavities. So far, only elliptical cavities have been coated with Nb3Sn and this technique has not yet been applied to cavities with complex geometries, which are also helpful in the accelerator science field. The Half-wave resonator could provide us data across frequencies of interest for particle accelerators world wide. Similarly the Twin axis cavity proposed for Energy Recovary Linac (ERL) applications could benefit from Nb3Sn coating. But with their advanced geometries, increased area, more number of ports and hard to reach areas, a different coating approach is needed to provide a uniform coating of Nb3Sn. We used twin axis cavity to optimize the coating technique and followed a low temperature annealing to further improvement of the thin film quality by low temperature annealing as a post coating method. With these we could expand the current coating system at JLab to coat complex cavity models

Tiskumara, Jayendrika↗