Search NASA⌕ Search

SEARCH · Search NASA

Results for “Annular Fuel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Fuel Preheat Effects on Soot-Field Structure in Laminar Gas Jet Diffusion Flames Burning in 0-g and 1-g

An experimental investigation conducted at the 2.2-s drop tower of the NASA Lewis Research Center is presented to quantify the influence of moderate fuel preheat on soot-field structure within 0-g laminar gas jet diffusion flames. Parallel work in 1-g is also presented to delineate the effect of elevated fuel temperatures on soot-field structure in buoyant flames. The experimental methodology implements jet diffusion flames of nitrogen-diluted acetylene fuel burning in quiescent air at atmospheric pressure. Fuel preheat of approximately 100 K in the 0-g laminar jet diffusion flames is found to reduce soot loadings in the annular region, but causes an increase in soot volume fractions at the centerline. In addition, fuel preheat reduces the radial extent of the soot field in 0-g. In 1-g, the same fuel preheat levels have a more moderated influence on soot loadings in the annular region, but are also seen to enhance soot concentrations near the axis low in the flame. The increased soot loadings near the flame centerline, as caused by fuel preheat, are consistent with the hypothesis that preheat levels of approximately 100 K enhance fuel pyrolysis rates. The results show that the growth stage of particles transported along the soot annulus is shortened both in 1-g and 0-g when elevated fuel temperatures are used.

Konsur, Bogdan↗
NASA NTRS1958

A Preliminary Investigation of the Performance of a Short-length Turbojet Combustor Using Vaporized Hydrocarbon Fuels

Two short turbojet combustors designed for use with vaporized hydrocarbon fuels were tested in a one-quarter annular duct. The experimental combustors consisted of many small "swirl-can" combustor elements manifolded together. This design approach allowed the secondary mixing zone to be considerably reduced over that of conventional combustors. The over-all combustion lengths, for the two configurations were 13.5 and 11.0 inches, approximately one-half the length of the shortest conventional combustors. These short combustors did not provide combustion efficiencies as high as those for conventional combustors at low pressures. However, over the range of combustor-inlet total-pressures expected in aircraft capable of flight at Mach numbers of 2.5 and above, these short combustors gave very high efficiencies. A combustion efficiency of 97 percent was obtained at a combustor-inlet total-pressure of 25.0 inches of mercury absolute, reference velocity of 120 feet per second, and inlet-air total temperature of 1160 deg R. By proportioning the fuel flow between the manifold rows of can combustor elements, control of the combustor-outlet radial total-temperature profile was demonstrated. Combustor totalpressure loss varied from 0.75 percent of the inlet total pressure at isothermal conditions and a reference velocity of 75 feet per second to 5.5 percent at a total-temperature ratio of 1.8 and a reference velocity of 180 feet per second.

Jones, R. E.↗
NASA NTRS1976

Experimental clean combustor program, phase 2

The primary objectives of this three-phase program are to develop technology for the design of advanced combustors with significantly lower pollutant emission levels than those of current combustors, and to demonstrate these pollutant emission reductions in CF6-50C engine tests. The purpose of the Phase 2 Program was to further develop the two most promising concepts identified in the Phase 1 Program, the double annular combustor and the radial/axial staged combustor, and to design a combustor and breadboard fuel splitter control for CF6-50 engine demonstration testing in the Phase 3 Program. Noise measurement and alternate fuels addendums to the basic program were conducted to obtain additional experimental data. Twenty-one full annular and fifty-two sector combustor configurations were evaluated. Both combustor types demonstrated the capability for significantly reducing pollutant emission levels. The most promising results were obtained with the double annular combustor. Rig test results corrected to CF-50C engine conditions produced EPA emission parameters for CO, HC, and NOX of 3.4, 0.4, and 4.5 respectively. These levels represent CO, HC, and NOX reductions of 69, 90, and 42 percent respectively from current combustor emission levels. The combustor also met smoke emission level requirements and development engine performance and installation requirements.

Gleason, C. C.↗
NASA NTRS1983

Effects of tripropellant engines on earth-to-orbit vehicles

The effects of tripropellant engines on earth-to-orbit vehicles is examined in terms of their impact on engine configurations and launch capabilities. Hydrocarbon fuel with some oxygen is used in tripropellant fuels, with hydrogen as a back-up fluid for coolant and driving the pumps. Engine concepts which implement tripropellant fuels include a hydrogen-gas generator engine with staged combustion, a two-mode engine burning hydrocarbon fuel in one chamber and hydrogen in another, a dual expander engine with a central hydrocarbon nozzle and an annular hydrogen nozzle, and a dual throat engine. The use of hydrocarbons reduces the fuel weight by providing a higher specific impulse than with LOX-LH2 systems alone. Studies have shown that single-stage-to-orbit vehicles capable of lifting 13.6 Mg are possible with tripropellant engines. A dual-expander engine, is identified as offering the most fuel dry mass reduction for a given payload if cooling requirements can be satisfied. Further development of the tripropellant engines is concluded to be beneficial.

Martin, J. A.↗
NASA NTRS1952

Cooling Characteristics of an Experimental Tail-pipe Burner with an Annular Cooling-air Passage

The effects of tail-pipe fuel-air ratio (exhaust-gas temperatures from approximately 3060 degrees to 3825 degrees R), radial distributiion of tail-pipe fuel flow, and mass flow of combustion gas and the inside wall were determined for an experimental tail-pipe burner cooled by air flowing through and insulated cooling-air to combustion gas mass flow from 0.066 to 0.192 were also determined.

Kaufman, Harold R↗
NASA NTRS1983

NASA advanced low emissions combustor program

The purpose of this program is to conduct combustion tests on lean, premixed, and prevaporized (LPP) combustor concepts designed for use in commercial aircraft engines to attain improved performance, durability, and lower pollutant emissions levels relative to current technology combustor designs. Four full annular combustors were designed for the CF6-50 engine. These concepts utilize premixing of the fuel and air, variable geometry, and fuel staging to control the equivalence ratios of the burning zone. The testing is being conducted on these four full annular combustors over a wide range of operating conditions at pressures up to actual subsonic cruise (1.16 MPa). The test results for the most promising of these combustor concepts are reported in this paper.

Goyal, A.↗
NASA NTRS2010

Conceptual Design of a Z-Pinch Fusion Propulsion System

This slide presentation reviews a project that aims to develop a conceptual design for a Z-pinch thruster, that could be applied to develop advanced thruster designs which promise high thrust/high specific impulse propulsion. Overviews shows the concept of the design, which use annular nozzles with deuterium-tritium (D-T) fuel and a Lithium mixture as a cathode, Charts show the engine performance as a function of linear mass, nozzle performance (i.e., plasma segment trajectories), and mission analysis for possible Mars and Jupiter missions using this concept for propulsion. Slides show views of the concepts for the vehicle configuration, thrust coil configuration, the power management system, the structural analysis of the magnetic nozzle, the thermal management system, and the avionics suite,

Adams, Robert↗
NASA NTRS1954

Investigation of Three Low-temperature-ratio Combustor Configurations in a 48-inch-diameter Ram-jet Engine

A preliminary evaluation was made of three types of combustor configurations in a 48-inch-diameter ram-jet engine to determine the one with the greatest promise of ultimately achieving efficient and stable combustion at low fuel-air rations and low combustor-inlet pressure. The combustor configurations evaluated include (1) a can-piloted configuration using a gutter-type flame holder with can-type pilot burners for stability, (2) an annular-piloted configuration using a gutter-type flame holder with an annular pilot burner to provide stability and to serve as a flow divider for confined fuel-air mixing, and (3) a can-type configuration using a flow divider for confined fuel-air mixing. No modifications were made to optimize the performance of any configuration. On the basis of this preliminary evaluation at an inlet-air temperature of about 990 degrees R, the annular-piloted combustor configuration appeared to have the greatest promise of permitting combustion efficiencies in excess of 0.90 at low fuel-air ratio with combustor-inlet pressures as low as 700 pounds per square foot absolute.

COMBUSTION - RAM-JET ENGINES↗
NASA NTRS1999

Soot Aerosol Properties in Laminar Soot-Emitting Microgravity Nonpremixed Flames

The spatial distributions and morphological properties of the soot aerosol are examined experimentally in a series of 0-g laminar gas-jet nonpremixed flames. The methodology deploys round jet diffusion flames of nitrogen-diluted acetylene fuel burning in quiescent air at atmospheric pressure. Full-field laser-light extinction is utilized to determine transient soot spatial distributions within the flames. Thermophoretic sampling is employed in conjunction with transmission electron microscopy to define soot microstructure within the soot-emitting 0-g flames. The microgravity tests indicate that the 0-g flames attain a quasi-steady state roughly 0.7 s after ignition, and sustain their annular structure even beyond their luminous flame tip. The measured peak soot volume fractions show a complex dependence on burner exit conditions, and decrease in a nonlinear fashion with decreasing characteristic flow residence times. Fuel preheat by approximately 140 K appears to accelerate the formation of soot near the flame axis via enhanced fuel pyrolysis rates. The increased soot presence caused by the elevated fuel injection temperatures triggers higher flame radiative losses, which may account for the premature suppression of soot growth observed along the annular region of preheated-fuel flames. Electron micrographs of soot aggregates collected in 0-g reveal the presence of soot precursor particles near the symmetry axis at midflame height, The observations also verify that soot primary particle sizes are nearly uniform among aggregates present at the same flame location, but vary considerably with radius at a fixed distance from the burner. The maximum primary size in 0-g is found to be by 40% larger than in 1-g, under the same burner exit conditions. Estimates of the number concentration of primary particles and surface area of soot particulate phase per unit volume of the combustion gases are also made for selected in-flame locations.

Konsur, Bogdan↗
NASA NTRS1987

NASA/GE advanced low emissions combustor program

The Advanced Low Emissions Combustor Program consisted of the design and testing of advanced combustor concepts utilizing lean, premixed, prevaporized fuel and variable geometry. The objective was to evaluate the potential of these combustor systems to provide very low pollutant emissions levels, superior performance and high durability relative to contemporary combustor designs. Four full annular combustor concepts were designed and fabricated for a 30:1 pressure ratio high bypass turbofan engine. The four full annular combustors with active variable geometry were tested at pressures up to approximately 0.7 MPa with Jet A fuel. The two most promising concepts were also tested in a high pressure sector combustor test rig capable of operation at the maximum engine pressures. The high pressure sector combustor tests were conducted with Jet A and a fuel with reduced hydrogen content. Results of the sector combustor tests are presented in this paper. The potential for very low emissions with premixed fuel was demonstrated. However, autoignition or flashback within the premixing systems was encountered at high pressures. Further development effort is required to address this problem area.

Ekstedt, E. E.↗
NASA NTRS1974

Modifications that improve performance of a double annular combustor at simulated engine idle conditions

Techniques were evaluated to determine if simple combustor modifications could be used to reduce the engine ground idle emissions of a double annular combustor designed for Mach 3.0 cruise operation. These techniques were radial fuel staging, the use of radial-inflow rather than axial-flow air swirlers, and the optimization of fuel-nozzle spray angle and differential pressure. Radial fuel staging and the use of radial-inflow air swirlers significantly improved performance at two ground idle test conditions simulating both low- and high-compression ratio engines.

Schultz, D. F.↗
NASA NTRS1986

Combustion research activities at the Gas Turbine Research Institute

The Gas Turbine Research Institute (GTRI) is responsible mainly for basic research in aeronautical propulsion. An annular diffuser for the turbofan augmentor, combustor ignition performance, combustor airflow distribution, fuel injectors, a vaporizer fuel injector, and an airblast atomizer are discussed.

Shao, Zhongpu↗
NASA NTRS2017

Thermal Analysis of the X3 Hall Thruster

Electric propulsion has generated significant interest recently as a mass efficient thrust option for deep space missions. This increased interest has drawn a renewed focus on improving the efficiency of electric propulsion thrusters, specifically Hall thrusters. Hall thrusters are a specific subset of ion engines that accelerate charged particles using a Hall current. Recent research into the 12.5 kW HERMeS (Hall Effect Rocket with Magnetic Shielding) for use on the proposed Asteroid Redirect Robotic Mission (ARRM) has shown the desire to use these devices on flight missions outside of earth orbit. This paper will focus on another Hall thruster, the X3. The X3 is a 100 kW class Hall effect thruster used for laboratory technology development. What makes the X3 unique, relative to more contemporary Hall thrusters beyond the order of magnitude increase in discharge power, is that the X3 is a 3 channel, nested Hall thruster. Common Hall thrusters typically have one annular channel where the plasma is constrained and used to charge the fuel and accelerated. The X3’s 3 channels are nested in a concentric format, with each channel fitting in a single plane. This presents very unique thermal modeling challenges with respect to quantifying the impact of plasma thermal loading and cross talk between the power dissipating components for each channel. This work will discuss the development of the X3 thermal model and the efforts to validate it with experimental data. Furthermore, some of the unique challenges that appear when trying to model high power components will be discussed. The X3 represents a challenging and interesting example of the issues affecting thermal modeling of high power electric propulsion thrusters which will become more prevalent as their use becomes more common. II

Hofer, Richard Jr.↗
NASA NTRS1997

Mixing of Pure Air Jets with a Reacting Fuel-Rich Crossflow

Jets in a crossflow play an integral role in practical combustion systems such as can and annular gas turbine combustors in conventional systems, and the Rich-burn/Quick-mix/Lean-burn (RQL) combustor utilized in stationary applications and proposed for advanced subsonic and supersonic transports. The success of the RQL combustor rests with the performance of the quick-mixing section that bridges the rich and lean zones. The mixing of jet air with a rich crossflow to bring the reaction to completion in the lean zone must be performed rapidly and thoroughly in order to decrease the extent of near-stoichiometric fluid pocket formation. Fluid pockets at near-stoichiometric equivalence ratios are undesirable because the high temperatures attained accelerate pollutant formation kinetics associated with nitric oxide (NO). The present study develops a model experiment designed to reveal the processes that occur when jet air is introduced into hot effluent emanating from a fuel-rich reaction zone.

Leong, M. Y.↗
NASA NTRS1950

Simulated altitude performance of two annular combustors with continuous axial openings for admission of primary air

Methods of introducing and distributing air and fuel in turbojet-engine combustors were evaluated with two fuels, AN-F-32 and AN-F-58. Investigations were made with two single-annulus liners in a one-quarter sector of a 25 1/2-inch-diameter turbojet combustor. Altitude performance data for these combustors are compared with existing data for a production-model double-annulus combustor. Altitude operating limits and combustion efficiencies of both single-annulus combustors were considerably higher than those of the double-annulus combustor; combustion efficiencies were insensitive to changes in fuel-air ratio.

COMBUSTION - TURBINE ENGINES↗
NASA NTRS1977

Emissions Reduction Technology Program

Combustor concepts having the potential for significantly lower emissions levels were investigated. The combustor emissions reduction was measured in an engine test. Emission characteristics common to all engine classes are shown. Multiple-burning zone combustors, specifically the double-annular and swirl-can combustors were studied. Airblast and air-assist fuel injection techniques were evaluated for emissions control potential. The combustor sceening and refining phases are summarized.

Jones, R. E.↗
NASA NTRS1983

Small Gas Turbine Combustor Primary Zone Study

A development process is described which consists of design, fabrication, and preliminary test evaluations of three approaches to internal aerodynamic primary zone flow patterns: (1) conventional double vortex swirl stabilization; (2) reverse flow swirl stabilization; and (3) large single vortex flow system. Each concept incorporates special design features aimed at extending the performance capability of the small engine combustor. Since inherent geometry of these combustors result in small combustion zone height and high surface area to volume ratio, design features focus on internal aerodynamics, fuel placement, and advanced cooling. The combustors are evaluated on a full scale annular combustor rig. A correlation of the primary zone performance with the overall performance is accomplished using three intrusion type gas sampling probes located at the exit of the primary zone section. Empirical and numerical methods are used for designing and predicting the performance of the three combustor concepts and their subsequent modifications. The calibration of analytical procedures with actual test results permits an updating of the analytical design techniques applicable to small reverse flow annular combustors.

Sullivan, R. E.↗
NASA NTRS1984

Experimental investigation of the low NO/sub x vortex airblast annular combustor

A low oxides of nitrogen vortex airblast annular combustor was evaluated which has attained the goal of 1 gm NO2/kg fuel or less during operation. The experimental combustor test conditions were a nominal inlet-air temperature of 703 K, inlet total pressures between 0.52 to 0.83 MPa, and a constant inlet Mach number of 0.26. Exit temperature pattern factors for all test points were between 0.16 and 0.20 and exit swirl flow angles were 47 degrees at isothermal conditions and 23 degrees during combustion. Oxides of nitrogen did not exceed 1.05 gm NO2/kg fuel at the highest inlet pressure and exhaust temperature tested. Previous correlations have related NOx proportionally to the combustor inlet pressure raised to some exponent. In this experiment, a band of exponents between 0.5 and 1.0 resulted for fuel-air ratios from 0.023 to 0.027 and inlet pressures from 0.52 to 0.83 MPa.

Johnson, S. M.↗