Search NASA⌕ Search

SEARCH · Search NASA

Results for “BENDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

AMMT FY23 HFIR Irradiation Test Matrix – Supported by the Design of a Miniature Bend Bar Irradiation Vehicle

With the continued advancement of additive manufacturing (AM) techniques, interest has grown in the development and qualification of steels produced via these methods for use in the structural components of advanced nuclear reactors. Therefore, it is crucial that the properties of these materials such as the tensile strength and fracture toughness be investigated following neutron irradiation to support their use in industry. To that end, a test plan to irradiate several tensile and bend bar specimens in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory was proposed, along with the development of a new “MINBEN” capsule design that features MBS-1 bend bar specimens that have a larger cross-sectional area than those of previous designs, which allows for higher temperature out-of-pile testing. The specimens include AM 316H stainless steel with wrought 316H and A709 stainless steels for reference, and they will be irradiated at 2 dpa and 10 dpa—corresponding to roughly 1 and 5 cycles at the HFIR midplane—at temperatures of 400°C and 600°C. The MINBEN design was found to be capable of providing specimen test plane average temperatures in the range of 220–660°C for six specimens, with a min-max spread in this temperature of ~40°C and a 95% confidence interval of ~24°C. This analysis shows that the capsule provides an effective vehicle for gathering needed high-temperature fracture toughness data.

36 MATERIALS SCIENCE↗
DOE OSTI2025

On Possibilities of Using Edge Radiation for X-ray and Electron Beam Diagnostics at Bending Magnet Beamlines of NSLS-II

Spectral flux density distributions of long-wavelength Edge Radiation, i.e. radiation generated by relativistic electrons at edges of bending magnets in a storage ring are described, both analytically and numerically. Possibilities of using this radiation for the alignment of optical components of bending magnet beamlines at NSLS-II and for non-destructive X-ray and electron beam diagnostics at these beamlines are discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Dipole Bend Magnets: Design Considerations

This analysis provides a design of a dipole bend magnet for a beamline, stepping through various considerations while assembling a design. This report can be used as a basis of a bending dipole magnet applicable to LANSCE, a scalable point design for other applications, or as a systematic process for developing a magnet design from scratch. The goal is more to answer, 'Is it reasonable?' than to address correction factors. In this specific case, the dipole should provide 3 kG within a 6.35-cm (2.5") gap across an area provided by 25×15-cm pole pieces. This provides roughly 17° and 21° deflection for proton at 3.0 and 2.1 MeV, respectively.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Bend inducible self-folding Origami flexures and microsystems

The present disclosure relates to a spatio-temporal stimulus responsive foldable structure. The structure may have a substrate having at least a region formed to provide engineered weakness to help facilitate bending or folding of the substrate about the region of engineered weakness. The substrate is formed to have a first shape. A stimulus responsive polymer (SRP) flexure is disposed at the region of engineered weakness. The SRP flexure is responsive to a predetermined stimulus actuation signal to bend or fold in response to exposure to the stimulus actuation signal, to cause the substrate to assume a second shape different from the first shape.

Kampasi, Komal↗
DOE OSTI2020

On the failure mechanisms of Cr-coated 316 stainless steel in bending fatigue tests

Here, fully-reversed cyclic bending tests were conducted on uncoated and Cr-coated 316 stainless steel specimens. At high stresses, the uncoated specimens outperformed the Cr-coated ones, while the trend reversed at low stresses. For Cr-coated specimens subjected to high stress amplitude loading, experimental observations showed crack initiation at the Cr/substrate interface due to shear steps formed from dislocation activities in the substrate—a conclusion supported by accompanying finite element analysis. Interfacial crack initiation was not observed under low stress amplitudes. This difference in fatigue crack initiation mechanisms induced an opposite trend in fatigue life between high and low stress amplitudes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural effects on the rotating bending fatigue behavior of Ti–6Al–4V produced via laser powder bed fusion with novel heat treatments

The rotating bending fatigue (RBF) behavior (fully reversed, R = -1) of additively manufactured (AM) Ti–6Al–4V alloy produced via laser powder bed fusion (PBF-L) was investigated with respect to different microstructures achieved through novel heat treatments. The investigation herein seeks to elucidate the effect of microstructure by controlling variables that can affect fatigue behavior in Ti–6Al–4V, such as chemistry, porosity, and surface roughness. In order to control these variables, different hot isostatic pressing (HIP) treatments at 800 °C, 920 °C, and 1050 °C with a 920 °C temper were applied to three sets of Ti–6Al–4V cylinders that originated from the same PBF-L build, such that there were 30 tests per condition. After HIP treatment, the specimens were machined and tested. The highest runout stress was achieved after sub-β transus HIP at 800 °C for 2 h at 200 MPa of pressure. A significant drop in fatigue strength was attributed to large prior-β grains and grain boundary α resulting from super-β transus HIP treated specimens. In conclusion, for the sub-β transus HIP specimens, differences in fatigue strength were attributed to α lath thickness, relative dislocation density, and dislocation boundary strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Damage evolution and ductile fracture of commercially-pure titanium sheets subjected to simple tension and cyclic bending under tension

This paper describes a study into the evolution of damage in commercial-purity titanium (CP–Ti) sheets subjected to cyclic bending under tension (CBT) and uniaxial tension (simple tension, ST). Sections were taken from sheets that were strained to various levels under both methods and were imaged using X-ray computed tomography (XCT) to reveal insights into the size, density, and distribution of microvoids in the sheets. Digital image correlation (DIC) was also used to observe the surface strain of CBT and ST sheets during testing. These results showed that elongation to failure (ETF) for CBT deformation is about 2.5× higher than for ST, local longitudinal strains in the bulk of the CBT sample are around 1.3× higher than the peak strain in the ST necked region, and 1.7× higher in the localized region of CBT failure. It was found that the volume-density of voids in both sheets followed a similar exponential increase with strain, reaching nearly 45× higher in the CBT than the ST sheets before the onset of failure, mainly due to the higher strain levels achieved. A higher volume density of voids developed in the center of sheets at high levels of strain, for both processes, with the density in the sheet center becoming approximately double that found near the edges. Scanning electron microscopy (SEM) was used to examine the fracture surface of CBT and ST sheets after failure. The observations are presented and discussed highlighting the CBT process as effective to delay ductile fracture of the CP-Ti sheets.

Commercially pure titanium↗
DOE OSTI2021

A 90 ° bend curved light-guide for TOF scintillating detectors

We report here a bench study of TOF resolution using a 90° bend curved solid light-guide (LG) used to transport the light from a plastic scintillator counter to a photomultiplier (PMT). The 90° LG allows the rotation of the PMT axis to be vertical to the detector axis, in an environment featured by a strong magnetic field along the detector surface, or other geometrical constrains. We show that with a TOF counter of 2000 x 100 x 60 mm 3 and light read-out by PMTs at its two 100 × 60 mm 2 sides, when 90° LG benders are used between the scintillating bar and the PMTs on both sides, the TOF resolution is worsen, by 5–10%.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Effect of layer bending on montmorillonite hydration and structure from molecular simulation

Conceptual models of smectite hydration include planar (flat) clay layers that undergo stepwise expansion as successive monolayers of water molecules fill the interlayer regions. However, X-ray diffraction (XRD) studies indicate the presence of interstratified hydration states, suggesting non-uniform interlayer hydration in smectites. Additionally, recent theoretical studies have shown that clay layers can adopt bent configurations over nanometer-scale lateral dimensions with minimal effect on mechanical properties. Therefore, in this study we used molecular simulations to evaluate structural properties and water adsorption isotherms for montmorillonite models composed of bent clay layers in mixed hydration states. Results are compared with models consisting of planar clay layers with interstratified hydration states (e.g. 1W–2W). The small degree of bending in these models (up to 1.5 Å of vertical displacement over a 1.3 nm lateral dimension) had little or no effect on bond lengths and angle distributions within the clay layers. Except for models that included dry states, porosities and simulated water adsorption isotherms were nearly identical for bent or flat clay layers with the same averaged layer spacing. Similar agreement was seen with Na- and Ca-exchanged clays. In conclusion, while the small bent models did not retain their configurations during unconstrained molecular dynamics simulation with flexible clay layers, we show that bent structures are stable at much larger length scales by simulating a 41.6×7.1 nm 2 system that included dehydrated and hydrated regions in the same interlayer.

58 GEOSCIENCES↗
DOE OSTI2020

High precision magnetic field measurement and mapping of the LEReC 180 degree bending magnet using very low field NMR with hall combined probe (140 - 350 gauss)

The Relativistic Heavy Ion Collider (RHIC) at BNL are using the Low Energy RHIC Electron Cooling (LEReC) to conduct experiments that search for the quantum chromodynamic (QCD) critical point. The first ever electron cooling based on the RF acceleration of electron beams was experimentally demonstrated on April 5, 2019 at LEReC at BNL. The first critical step in obtaining successful 3D non-magnetized cooling of the Au ion bunches in the RHIC cooling section was matching the electron beam energy with a relative error less than 5*10 -4 to the ion beam energy. Part of the LEReC beamline is a dipole magnet that bends the electron beam 180 degree. One of the most outstanding measurement challenges is that the dipole field is so low (≈200 G). Most of the existing NMR probes can only measure fields >400 G. Lower signal-to-noise ratio at low fields is requires the use of larger sample volumes. Working with CAYLAR, a NMR probe has been redesigned and optimized for these low field measurements with high resolution. We report the methods, challenges, and results for extensive magnetic field mappings of the 180 dipole magnet. A combination of NMR and Hall sensors has been successfully implemented to measure uniform field regimes inside the magnet center area and non-uniform field regimes at the magnet ends. Detailed measurement and mapping have been performed at five radii and five heights along the beam trajectory. Meanwhile a finite element magnetic modeling simulation of the magnet using Opera software has been performed. The calculated and measured data are compared, and the calculated data is good reference for measured data over long length mapping from magnet edge to center. The measured magnetic measurement data is directly useful for beam instrumentation, diagnostics and operation.

Magnetic Field Measurement↗
DOE OSTI2021

Small-sized specimen design with the provision for high-frequency bending-fatigue testing

The testing and study of emerging materials—such as additively manufactured materials—demands for specimen designs that are cost effective and time saving. Here the design of a small-sized bending-fatigue test specimen for an ultrasonic fatigue testing system is reported in this paper. The design is optimized based on the finite element analysis and analytical-solution results to achieve the proper vibration shape and stress distribution. The proposed design is evaluated in the high- and very-high-cycle fatigue regimes under 20-kHz frequency. Both simulation and testing results confirm that the desirable vibration mode occurs and the specimen fails at the designated test (gauge) section, where the maximum stress exists. The stress–life (S–N) curve is obtained for Inconel alloy 718 and indicates an expected trend.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Correlation of Band Bending and Ionic Losses in 1.68 eV Wide Band Gap Perovskite Solar Cells

Abstract Perovskite solar cells (PSCs) are promising for high‐efficiency tandem applications, but their long‐term stability, particularly due to ion migration, remains a challenge. Despite progress in stabilizing PSCs, they still fall short compared to mature technologies like silicon. This study explores how different piperazinium salt treatments using iodide, chloride, tosylate, and bistriflimide anions affect the energetics, carrier dynamics, and stability of 1.68 eV bandgap PSCs. Chloride‐based treatments achieved the highest power conversion efficiency (21.5%) and open‐circuit voltage (1.28 V), correlating with stronger band bending and n‐type character at the surface. At the same time, they showed reduced long‐term stability due to increased ionic losses. Tosylate‐treated devices offered the best balance, retaining 96.4% efficiency after 1000 h (ISOS‐LC‐1I). These findings suggest that targeted surface treatments can enhance both efficiency and stability in PSCs.

14 SOLAR ENERGY↗
DOE OSTI2023

Band Bending at CdTe Solar Cell Contacts: Correlating Electro‐Optical and X‐Ray Photoelectron Spectroscopy Analyses of Thin Film Solar Cells

With the semiconductor bulk properties reaching target values for highly efficient solar cells, efforts are applied to reduce losses at solar cell interfaces and contacts. Advances in understanding back contacts in thin‐film polycrystalline CdTe solar cells, a leading thin‐film PV technology, are reported. By using X‐Ray photoelectron spectroscopy, Kelvin probe spectroscopy, time‐ and energy‐resolved photoluminescence, defects at the back contact are analyzed. Densities of recombination centers and charged defects that induce near‐back‐contact band bending, both resulting in recombination losses, were estimated. Electro‐optical and surface analysis results are integrated into a device model, simulating the performance of CdSeTe/CdTe solar cells with 902 mV open circuit voltage.

14 SOLAR ENERGY↗
DOE OSTI2020

Experimental verification of a crystal plasticity-based simulation framework for predicting microstructure and geometric shape changes: Application to bending and Taylor impact testing of Zr

This paper is concerned with experimental verification of a recently developed multi-scale simulation framework for plastic deformation of metallic materials from quasi-static to impact deformation conditions. The framework is a visco-plastic self-consistent (VPSC) polycrystalline model embedded in an implicit finite element method (FE-VPSC) to provide a microstructure-sensitive constitutive response at each material point. Each material point of the FEM model is a polycrystalline aggregate with crystallographic deformation mechanisms operating at the single crystal scale with their evolving activity based on a dislocation density-based hardening law and texture. Four beams and three cylinders machined in different orientations from a textured plate of high-purity zirconium are tested quasi-statically in 4-point bending and at speeds of 100 m/s, 170 m/s and 243 m/s during Taylor impact tests, respectively. The variation in dimensional changes resulting from different sample orientations in the plate with respect to loading directions is measured for each sample. Moreover, texture and twinning characterization is performed using electron backscattered diffraction (EBSD). The deformation processes and underlying evolution of microstructure are successfully simulated using the FE-VPSC framework. In doing so, the model parameters are optimized and validated across a broad range of strain rates and temperatures. Simulation results in terms of geometrical changes and microstructural evolution are compared with the experimental measurements. The model predicts anisotropic material flow resulting from the hard-to-deform crystallographic directions, the development of gradients in texture and twinning through the geometries, tension–compression asymmetry, as well as the extent of plasticity under impact.

42 ENGINEERING↗
DOE OSTI2024

Advanced storage ring lattice options based on hybrid six-bend achromat for Stanford Synchrotron Radiation Lightsource upgrade

Three storage ring lattices have been designed as options for a future upgrade of the Stanford synchrotron radiation lightsource (SSRL). The three options differ in circumference and targeted future site, with one to be built in the tunnel of the present SPEAR3 ring, one as a green field ring on the SLAC campus, and the third in the tunnel of the decommissioned PEP-II ring. The lattices are based on the newly proposed hybrid 6-bend achromat (H6BA) lattice cells, which is ideal for pushing the photon beam brightness while achieving excellent nonlinear dynamics performance. The transparent matching conditions are enforced to minimize the negative impact of the loss of periodicity due to insertion of various long straight sections. Numerical optimization is performed to further improve the nonlinear dynamics. Finally, in addition to reaching very low emittances, the lattices can accommodate traditional off-axis injection and achieve beam lifetimes similar to or exceeding that of typical third generation rings.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Binding the Power of Cycloaddition and Cross-Coupling in a Single Mechanism: An Unexpected Bending Journey to Radical Chemistry of Butadiynyl with Conjugated Dienes

What if an experiment could combine the power of cycloaddition and cross-coupling with the in situ formation of an aromatic molecule in a single collision? Crossed molecular beam experiments augmented with electronic structure and statistical calculations provided compelling evidence on a novel radical route involving 1,3-butadiynyl (HCCCC; X 2 Σ + ) radicals synthesizing (substituted) arylacetylenes in the gas phase upon reactions with 1,3-butadiene (CH 2 CHCHCH 2 ; X 1 Ag) and 2-methyl-1,3-butadiene (isoprene; CH 2 C(CH 3 )CHCH 2 ; X 1 A'). Furthermore, this elegant mechanism de facto merges two previously disconnected concepts of cross-coupling and cycloaddition–aromatization in a single collision event via the formation of two new C(sp 2 )–C(sp 2 ) bonds and bending the 180° moiety of the linear 1,3-butadiynyl radical out of the ordinary by 60° to 120°. In addition to its importance to fundamental organic chemistry, this unconventional mechanism links two previously separated routes of gas-phase molecular mass growth processes of polyacetylenes and polycyclic aromatic hydrocarbons (PAHs), respectively, in low-temperature environments such as in cold molecular clouds like the Taurus Molecular Cloud (TMC-1) and in hydrocarbon-rich atmospheres of planets and their moons such as Titan, what revises the established understanding of low-temperature molecular mass growth processes in the Universe.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Stretching and Bending Moduli of Bilayer Films Inferred from Wrinkle Patterns

Wrinkling patterns were used to investigate the mechanical properties of thin poly­(styrene) (PS)/poly­(methyl methacrylate) (PMMA) and PS/gold (Au) bilayer films. Films were floated on water with a water drop on the surface to induce wrinkling. The thicknesses and thickness ratios of the films were varied over a broad range. The PS/PMMA bilayer was chosen to provide a contrast in wetting properties, with equilibrium contact angles of θPMMA = 68° and θPS = 88° with water. The PS/Au bilayer was chosen to provide a large contrast in Young’s moduli, E Au = 72 GPa and E PS = 3.4 GPa. The stretching (Y) and bending (B) moduli of the bilayer films were obtained from measurements of the length and number of wrinkles in the wrinkle patterns. The experimentally derived values of Y and B were in reasonable agreement with the values computed from the bulk Young’s moduli and the thicknesses of the two components in the bilayer. The values of Y and B did not depend on which face of the film was exposed to the water droplet or bath when the capillary stresses were considered. Thus, finite size effects from the film thicknesses were unimportant over the range of thicknesses studied, and no relative displacement of the films was found, with the films remaining well-bonded even with deformation associated with wrinkling.

Chang, Jooyoung↗