Search NASA⌕ Search

SEARCH · Search NASA

Results for “Biochar”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Mitigation of Acute Ammonia Emissions With Biochar During Swine Manure Agitation Before Pump-Out: Proof-of-the-Concept

Ammonia (NH 3 ) emissions from animal agriculture can cause eutrophication of water ecosystems and are precursors to secondary particulate matter (PM 2 .5 ). NH 3 emissions from stored swine manure represent nutrient loss affecting the fertilizing value of manure. The short-term emission bursts occur when farmers agitate manure before emptying storage and fertilizing fields. There is no proven technology to mitigate gaseous emissions during agitation, while the hazards of acute releases (e.g., H 2 S) are well-known. Biochar mitigates NH 3 emissions from manure over the long-term. The objective of this research was to evaluate the mitigation of acute NH 3 emissions during/after agitation. Two biochars, highly alkaline and porous (HAP from corn stover) and red oak (RO), were tested. The 6 and 12 mm-thick layers of biochar powder were surficial applied followed by 3 min agitation. NH 3 concentrations were measured before/during/after agitation. Mitigation was assessed by comparing: (i) the maximum (peak) flux, (ii) total emission (from agitation start till NH 3 concentration returned to the before-agitation), and (iii) the total emissions during agitation. The 12 mm HAP significantly ( p < 0.05) reduced (i–iii) by 63, 70, and 85%, respectively. The 6 mm HAP significantly reduced (i–iii) by 76, 75, and 78%, respectively. The 12 mm RO significantly reduced (i–iii) by 9, 53, and 57%, respectively. The 6 mm RO significantly reduced (i–iii) by 61, 86, and 63%, respectively. The NH 3 emission kinetics model confirmed that a 6 mm dose was just as effective as the larger dose. More research is needed to optimize and scale-up mitigating emissions and retention of nutrients in manure with biochar.

Chen, Baitong↗
DOE OSTI2025

Upconversion of non-recycled MSW paper fractions into biochar via slow pyrolysis and life cycle analysis: Pathways to net negative GHG emission

This study presents an integrated and sustainable approach to valorizing non-recycled municipal solid waste (MSW), a heterogeneous and underutilized waste stream destined for landfilling, by converting it into valuable biochar resources. Specifically, we investigated the upcycling of nonrecycled paper waste based on compositional analysis into four major fractions: high cellulose, high lignin, high contamination, and high ash content papers. These fractions were then homogenized and subjected to slow pyrolysis. The high cellulose fraction (36.1 %) was the most abundant, and contained 66.7 % cellulose, while the high lignin fraction showed the highest lignin (12.1 %) and carbon content (44 %), resulting in highest energy value of 17.4 MJ kg −1 . Biochar yields ranged from 25.6 % to 35.6 %, with the high ash fraction producing the highest yield and alkalinity (pH ≈ 11.2) due to its higher mineral content. Elemental analysis revealed enhanced carbon content up to 76.9 % and reduced oxygen and hydrogen, confirming effective carbonization. The high lignin-derived biochar showed the highest aromatic carbon content (82.8 %) and greater structural stability, while contaminated and ash-rich fractions exhibited dense, low-porosity surfaces due to the presence of contaminants and minerals. Spectroscopic analysis revealed degradation of carbohydrates, disappearance of cellulose peaks and formation of aromatic and mineral derived phases. The scaled life cycle process yielded a global warming potential (GWP) of 119.3 kg CO 2 -eq per ton of dry paper waste, offset by soil carbon sequestration of − 556.41 kg CO 2 -eq, resulting in a net impact of − 427.36 kg CO 2 -eq. This represents a net carbon removal exceeding by ~186 % the emissions associated with landfilling paper waste with electricity generation.

09 BIOMASS FUELS↗
DOE OSTI2021

Experiment and computational fluid dynamics investigation of biochar elutriation in fluidized bed

Here, in fluidized bed biomass fast pyrolysis, the biomass is converted to biochar and elutriated. The elutriation rate is a key parameter in reactor designs and operations. This research presents a video-based continuous measurement of biochar elutriation rate in a fluidized bed with sands and biomass as bed materials. The fluidized bed is simulated with the Computational Fluid Dynamics - Coarse-Grained Discrete Element Method (CFD-CGDEM) in MFiX. The fluidization behavior of non-spherical sands can be more accurately captured when a rolling friction model is used. The predicted elutriation rate is close to the experimental measurement when the particle size distributions are considered and the filtered drag with a shape correction is used. These results validated the accuracy of the MFiX based CFD framework for the prediction of biochar elutriations in the fluidized bed biomass fast pyrolysis reactor.

09 BIOMASS FUELS↗
DOE OSTI2023

Microwave resonance enhanced CO 2 reduction using biochar

The conventional process for CO 2 conversion requires high energy and expensive catalysts, and shows poor product selectivity. Here, in this study, we address these challenges by investigating an environmentally friendly method for CO production through the variable frequency microwave-driven CO 2 Boudouard reaction over biochar. We hypothesized that tuning the microwave frequency to align with the dielectric properties of biochar, and thereby induce a resonance effect, could significantly enhance reaction efficiency. Experiments were conducted to explore the effect of microwave frequency on CO 2 conversion efficiency in the variable frequency microwave reactor operating within a frequency range of 2430–6000 MHz. Results reveal a significant resonance effect at 4225 MHz resulting in an outstanding CO 2 conversion of 96.3%, in sharp contrast to the complete absence of conversion observed at the conventional 2450 MHz. The resonance frequency not only facilitated exceptional conversion but also remarkably improved energy efficiency, yielding a productivity of 1427.5 µmol/kJ of CO. This represents a remarkable 474-fold increase compared to electrical heating. Furthermore, continuous microwave irradiation at this optimized frequency demonstrated remarkable stability and induced substantial enhancements in the pore structure and surface area of biochar. This innovative approach provides promising insights into sustainable and efficient CO production processes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Efficiency and mechanisms of Sb(III/V) removal by Fe-modified biochars using X-ray absorption spectroscopy

Fe-modified biochars (FeBC) are effective antimony (Sb) removal materials; however, the removal mechanisms require further investigation. In this study, aqueous Sb(III) and Sb(V) removal by FeBC (300, 600, and 900 °C) was evaluated, with the adsorption mechanisms investigated using X-ray absorption spectroscopy (XAS). Screening results (based on removal efficiencies) using different types of FeBC indicated the 900 °C FeCl3- modified biochar (FeCl3BC900) achieved the best Sb(III/V) removal performance. The kinetics of the Sb(III/V) removal process were best fitted by a pseudo-second-order model. Additionally, the isothermal results were described by Langmuir and Redlich-Peterson models. Aqueous analysis and X-ray absorption near-edge structure data fitting indicated Sb(III) was oxidized to Sb(V) in the Sb(III)-spiked system, and the oxidation extent increased with increasing pyrolysis temperature. The oxidation process rapidly occurred in both the solution and biochar. No Sb(V) was reduced to Sb(III) in the Sb(V)-spiked system. The XAS results of the isothermal experiment indicated the oxidation capacity of FeCl3BC900 was limited for high initial Sb(III) concentrations. The SbFe1 and Sb-Fe2 bonding distances were 3.05–3.10 and 3.47–3.54 Å, respectively, indicating inner-sphere complexes were formed during the Sb(III/V) removal processes. The Sb(III/V) removal mechanisms included electrostatic adsorption, inner-sphere complexes, and coprecipitation. Oxidation was also involved in Sb(III) removal.

Antimony↗
DOE OSTI2025

Process Feasibility Analysis of Waste Biomass Valorization to Biochar and Bio-Oil via Slow and Fast Pyrolysis

The United States has abundant biomass and waste feedstock to support the nation's energy addition and affordability targets. Pyrolysis, a thermochemical conversion process, decomposes lignocellulosic feedstocks into liquid, solid, and gaseous fuels that can contribute to the domestic production of biofuels, biopower, and bioproducts. Growing private sector interest in this technology is a key motivation for this comprehensive techno-economic process modeling analysis of a respective biorefinery that includes feedstock preprocessing, slow and fast pyrolysis, and product separation to bio-oil, biochar, and syngas hydrocarbons. Results show that biochar from slow pyrolysis could achieve minimum selling prices (MSPs) of $\$$188-$\$$260/t, competitive with reported market values, while bio-oil from fast pyrolysis is estimated to yield MSPs of $\$$6.49-$\$$9.68/GGE, approximately twice conventional fuel benchmarks. Sensitivity analysis identifies feedstock cost, product yield, and scale as primary cost drivers, while scenarios involving biochar carbon credits and high value applications may substantially improve economics. Overall, these results suggest that continued innovation in feedstock logistics, process integration, and market development will be critical to achieving economically viable and scalable bioproducts.

09 BIOMASS FUELS↗
DOE OSTI2024

Biochar-compost-based controlled-release nitrogen fertilizer intended for an active microbial community

Nitrogen (N) fertilizers in agriculture suffer losses by volatilization of N to the air, surface runoff and leaching into the soil, resulting in low N use efficiency (NUE) (< 50%) and raising severe environmental pollutions. Controlled- release nitrogen fertilizers (CRNFs) can control the release of N nutrients to NUE in crop production. Different methods were used to develop new CRNFs. However, different CRNF technologies are still underdeveloped due to inadequate controlling on N releasing time and/or unsustainable diffusion. The study on the influences of CRNF processing parameters on microbial conditions are lacking when the CRNFs composed of various bio-ingredients such as biochar, composts, and biowaste. The complexity of processing methods, material biodegradability, and other physical properties make current CRNFs of questionable value in agricultural production. This research aims to develop a novel biochar-compost-based controlled-release urea fertilizer (BCRUF) to preserve microbial properties carried by the compost. The BCRUF was synthesized by pelletizing the 50:50 (dry, wt/wt) mixture of biochar and compost. BCRUF was loaded with urea and then spray-coated with polylactic acid (PLA). The releasing time of two types of BCRUFs, coated and uncoated with PLA, for 80% of N release in water was up to 6 h at three different temperatures (4, 23, and 40 °C), compared to conventional urea fertilizer and commercial environmentally smart N (ESN) fertilizer. The releasing time of coated BCRUF for 80% N release in soil was up to 192 h (8 days). Fourier-transform infrared spectroscopy (FTIR) analysis revealed that no new functional groups were found in the release solution, indicating no new chemical hazards generated. The differential scanning calorimetry (DSC) tests also verified that its thermal stability could be up to 160 °C. The microbe populations in the BCRUF pellets were reduced after the pelleting and drying processes in BCRUF fabrication, but a few bacteria can endure in the air-drying process. BCRUF pellets soaked in water for 4 days retained some bacteria. The BCRUF showed very promising characteristics to improve NUE and sustainability in agricultural production.

58 GEOSCIENCES↗
DOE OSTI2022

Adsorption of methylene blue by bismuth impregnated biochar of different biomass materials: pore structure and surface chemistry characteristics

Abstract In this study, three different types of biochar (biomass materials were beech wood, corncob, and bamboo) were loaded with bismuth to form bismuth impregnated biochars (named respectively as Bi@WBC, Bi@CBC, and Bi@BBC) to investigate their properties (pore structure and surface chemistry characteristics) on methylene blue (MB) removal capacities. Three bismuth impregnated biochars made from different biomass materials were ranked for their adsorption capacity of MB as follows: Bi@WBC > Bi@CBC > Bi@BBC, in which Bi@WBC showed the largest Langmuir adsorption capacity of 178.59 mg g −1 . While the specific surface area (SSA) and pore volume of Bi@WBC were the largest (accounting for 477.74 m 2 g −1 and 0.15 cm 3 g −1 , respectively), according to the FTIR and XPS results, Bi@WBC (72.3%) exhibited a higher proportion of BiO bonds than the Bi@CBC (52.3%) and Bi@BBC (48.4%) did. Conclusively, the rich porous structure and surface functional groups of Bi@WBC affected the adsorption capacity of MB, and the chemical adsorption provided the main contribution. © 2022 Society of Chemical Industry (SCI).

Li, Peiyi↗
DOE OSTI2026

Understanding and Mitigating Stickiness in Biochar Produced through Acid Hydrolysis and Dehydration

Levulinic acid is a platform chemical with significant potential for conversion into a wide range of biobased chemicals and fuels. A common process for producing levulinic acid from lignocellulosic feedstocks involves acid hydrolysis and dehydration (AHDH), where hexose polymers are hydrolyzed into monomeric sugars and subsequently dehydrated to levulinic acid and formic acid in the presence of dilute sulfuric acid. However, scaling the AHDH process is challenging because of the formation of byproducts such as sticky biochar, which accumulates in continuous-flow reactors, reducing effective reaction volume and increasing process downtime. This study investigates the effect of a chemical preconditioning step on mitigating sticky biochar formation. Woody biomass was preconditioned at 170 °C with 0.26 wt % sulfuric acid for 30 min, resulting in substantial removal of hemicellulose and acid-soluble lignin. AHDH of these preconditioned solids produced biochar that did not adhere to reactor surfaces. TGA analysis confirmed that the chemical preconditioning step minimized interactions between hemicellulose-derived degradation products and lignin side chains, reducing sticky char formation. Additionally, the study observed a 6% higher yield of organic acids from softwood species compared to hardwoods, with bark content shown to negatively impact yield. These findings suggest that targeted preconditioning of lignocellulosic biomass can enhance reactor operability and improve organic acid production efficiency in AHDH processes.

biopolymers↗
DOE OSTI2025

Synthesis and Characterization of Soy Hull Biochar-Based Flexible Polyurethane Foam Composites

Flexible polyurethane foams are a diverse class of materials encompassing furniture, packaging, automotive, and many other industrial and domestic applications. Polyurethane foams are synthesized by the addition of polyols and isocyanates; however, the petroleum origin and toxic nature of isocyanates have driven many to look for more sustainable routes to production. Renewable fillers have emerged as a biobased resource to decrease the carbon footprint of this widely used polymeric material. In this study, soy hulls, as mass-produced, industrial by-products of soybean production, were used to create a biochar beneficial in the synthesis of flexible polyurethane foam composites. The addition of soy hull biochar was found to maintain the compression properties of foams at a decreasing isocyanate index, reducing the amount of isocyanates needed for production. In addition, the addition of biochar decreased the flammability of foams, important for many applications where consumer safety is important. The results point to the ability to create safer, more sustainable, and even more cost-effective polyurethane foams through the reduction in isocyanate use while maintaining the properties of this important class of polymers.

Chemistry↗
DOE OSTI2024

Multi-catalytic active site biochar-based catalysts for glucose isomerized to fructose: Experiments and density functional theory study

In this study, this work provides an innovative method for preparing different isomerization catalysts by impregnating different proportions of MgCl 2 and AlCl 3 and combining different K compounds on cellulose-derived biochar, followed by pyrolysis. Results show MgO and Al(OH) 3 existing in 4 Mg- 1 Al-C catalyst can obtain better catalytic effect on glucose isomerization than the singe of Al presenting in 0 Mg- 1 Al-C catalyst. Moreover, the synergism effects of the multi-catalytic active sites such as β-, γ -Al(OH) 3 , KCl, MgO, and K 4 H 2 (CO 3 ) 3 in Mg-Al-KHCO 3 -C catalyst can further lead to an increase in glucose isomerization, compared to the 4 Mg- 1 Al-C catalyst. The X-ray diffraction results present that the value of O/Al in Mg-Al-KHCO 3 -C catalyst is as high as 13.38, which provides many unsaturated acidic catalysis sites and benefits the glucose isomerization. Simultaneously, the TPD results reveal that the main active sites (MgO, Al(OH) 3 , and K 4 H 2 (CO 3 ) 3 ) in Mg-Al-KHCO 3 -C catalyst can provide weakly acidic and basic sites and avoid strongly acidic and basic sites to excessively attack the glucose. Based on the DFT analysis, the results indicate that the MgO has a great effect on the ring-opening reaction to form acyclic glucose, while Al(OH) 3+ has a great effect on promoting acyclic glucose hydrogen transfer isomerized to form fructose. Compared to other carbon-based metal catalysts, the prepared Mg-Al-KHCO 3 -C has excellent catalytic performance, which gives a higher fructose yield (38.7%) and selectivity (87.72%) and glucose conversion (44.12%) at 100 °C in 30 min. In this study, we develop a highly efficient Mg-Al-K-biochar catalyst for glucose isomerization and provide an efficient method for cellulose valorization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Biochar as a Building Material: Sequestering Carbon and Strengthening Concrete

It is possible to offset the carbon footprint of concrete by 60 kg (132 lbs) per cubic yard of ready-mix by deeply sequestering carbon with an engineered biochar additive. Our multidisciplinary team specializing in char production and cementitious materials has demonstrated that for every ton of cement, adding 100 kg of engineered biochar will not only lock in carbon, but also strengthen concrete in all key dimensions via enhancements to hydration and integration into the hardened matrix. As a non-chemical, inert additive the cement sequestration (CemSeq) char product can fully complement other powerful tools to reduce cement emissions and unlock the possibility for carbon negative concrete by 2050. The key findings of our initial research have shown that to achieve this the following are required: tailored milling of the char, using fast pyrolysis to produce the char, and modulating the cement flowability.

biochar↗
DOE OSTI2024

Controlling saturation to improve per- and polyfluoroalkyl substance (PFAS) removal in biochar-amended stormwater bioretention systems

Black carbon-amended bioretention systems are an increasingly popular strategy for the removal of organic contaminants, including poly- and perfluoroalkyl substances (PFASs) and other trace organic contaminants (TOrCs), from urban stormwater. Many PFASs preferentially accumulate at the air–water interface, but detention time requirements for stormwater bioretention systems typically result in full saturation of the bioretention systems, effectively removing their air–water interfaces. This study assessed the effect of bioretention system saturation on removal of PFASs, metals, and hydrophilic TOrCs. A field-aged mixture of 40% v/v sand, 30% v/v zeolite, and 30% v/v biochar was packed into columns which were operated with hydraulic controls to remain unsaturated or fully saturated throughout the duration of the experiment. Twenty-four storm events sized to a 95th percentile storm at a California, United States military site were simulated using synthetic stormwater fortified with aqueous film forming foam-derived PFASs, TOrCs, and metals to mimic real-world conditions. Unsaturated conditions outperformed saturated conditions for removal of all PFASs analyzed. A simulated inadvertent system perturbation (i.e. flooding event) in the unsaturated columns did not result in significantly greater mobilization of PFAS mass, suggesting that more sorption to the biochar occurred as a result of the transient retention of PFASs at the air–water interface reducing kinetic sorption limitations. Overall, maintaining unsaturated conditions in a biofilter may extend the sorptive filter lifetime for PFASs by up to 83%. The results have implications for bioretention system application and design for PFAS removal in contaminated catchment areas.

13 HYDRO ENERGY↗
DOE OSTI2024

Metal-organic-framework and walnut shell biochar composites for lead and hexavalent chromium removal from aqueous environments

Extensive research in recent years has explored the realm of porous carbon composites for various applications, including electrochemistry, structural materials, environmental remediation, and more. In particular, the fabrication of porous carbon composites using a metal-organic framework (MOF) and biochar (BC) for aqueous remediation is a fairly new avenue of research. In this study, a MOF-BC composite was synthesized with unmodified and chemically modified BCs using solvothermal synthesis. The composites were used as adsorbents to remediate heavy metals, such as lead (II) and chromium (VI), from aqueous environments. Here, it was verified that the MOF was homogeneously deposited onto the BC's surface using various material characterization techniques. Lead and chromium adsorption studies revealed a high adsorption capacity with greater than 99% removal for lead and ∼65% for chromium, respectively. Impressively, for lead, the highest observed experimental adsorption capacity of the MOF-chemically modified BC composite was 535 mg/g, compared to 240 mg/g for pristine BC. Meanwhile, the adsorption capacity of the same MOF-BC composite for chromium ions was low at 18 mg/g, compared to 80 mg/g for the chemically modified BC. The MOF-BC had a rapid adsorption rate, achieving equilibrium at only 150 min of reaction time for lead ions. MOF-BCs have higher adsorption for cationic lead through physisorption and ion-exchange mechanisms, whereas, for anionic chromium, removal is dominated only by physisorption mechanisms. The outcomes and methodological developments attained in this study offer a novel and compelling approach for synthesizing MOF-BC composites for aqueous remediation applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Performance of biochar assisted catalysts during hydroprocessing of non-edible vegetable oil: Effect of transition metal source on catalytic activity

Biochar-supported catalysts were developed from nickel (Ni) - and cobalt (Co)- nitrates and hydroxides and tested for the hydrotreatment of carinata oil. Nitrate-based (from water-soluble salts) and hydroxide-based (from water-insoluble salts) catalysts of Ni and Co were prepared via wetness impregnation and aqueous dispersion methods, respectively. The catalysts were characterized using various tools such as, confocal XRF, BET specific surface area analyzer, NH3-TPD, and SEM-EDS. Synchroton method showed nitrate-sourced metals were dispersed mostly in the pores while, the hydroxide-sourced metals were distributed mainly on the catalyst surface. C = C saturation and cracking of triglycerides, decarboxylation, and hydrogenation of aromatic structures appeared to be dominant on the hydroxides of transition metals, hence took place on catalyst surface. Methanation and dehydrogenation (thus aromatization), however, seemed to be a pore phenomenon, catalyzed more over nitrate-based catalysts. A reaction network was proposed based on chemical analysis of upgraded carinata oil and erucic acid model compound. Catalytic cracking followed by hydrotreatment performed better in terms of fuel properties than other approaches in this study.

Biochar catalysts↗
DOE OSTI2022

Application of Fe-doped biochar in Cr(VI) removal from washing wastewater and residual Cr(VI) immobilization in contaminated soil

High-content Cr(VI)-contaminated soils are challenging to remediate using a single remediation technique. This study combined soil washing and immobilization to remediate high-content (3440 mg kg -1 ) Cr(VI)-contaminated soil, which investigated the effects of operating time, temperature, and liquid-solid ratio (LSR) on the Cr(VI) removal efficiency of soil washing and evaluated the potential of Fe-doped biochar (FeBC) in soluble Cr(VI) removal from the washing wastewater and residual Cr(VI) immobilization in the washed soil. The Cr(VI) removal efficiency of soil washing increased with the operating time, temperature, and LSR, but still cannot remove Cr(VI) to achieve the safety content (<100 mg kg -1 ). FeBC showed satisfactory potential in both Cr(VI) removal and immobilization from wastewater and soil, in which the main mechanisms involve ion exchange, redox, and coprecipitation. These results demonstrate applying soil washing & immobilization to remediate high-content Cr(VI)-contaminated soil is a promising alternative method.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

Engineering acid-base active sites on an N-doped biochar catalyst for microwave-assisted biodiesel production from waste cooking oil

Acid-base bifunctional catalysts play a crucial role in converting high-free fatty acid (FFA) feedstocks into biodiesel by enabling the simultaneous esterification and transesterification of triglycerides in a single step, thereby minimizing saponification and streamlining the process. In this study, we report the design and development of a novel N-doped acid-base bifunctional biochar catalyst synthesized from renewable biomass precursors- glucose and chitosan. The catalyst’s acidic sites were introduced via surface functionalization with o-sulfobenzoic acid cyclic anhydride, grafting -SO₃H groups onto the carbon framework, while basic sites were generated from amine functionalities (-NH) derived from chitosan, yielding a robust and truly bifunctional surface. The catalyst was characterized and used for the microwave-assisted transesterification of waste cooking oil, and process optimization using response surface methodology (RSM-CCD) yielding a maximum biodiesel yield of 98.8 ± 0.4% under optimal conditions (methanol-to-oil molar ratio 20:1, catalyst loading 5.7 wt%, temperature 99 °C, and reaction time 46.6 min). The catalyst demonstrated good stability, maintaining a yield of 92.2 ± 0.4% after eight reuse cycles. A Life Cycle Assessment (LCA) conducted for 1 kg of biodiesel production revealed a global warming potential of 0.85 kg CO 2 eq and human toxicity potential of 1.59 kg 1,4-DB eq, with the largest environmental contributions arising from catalyst preparation and reuse. In conclusion, this work highlights a green and circular approach to biodiesel production, combining renewable catalyst design, waste feedstock utilization, and quantitative sustainability assessment to guide future developments in sustainable catalysis and biofuel engineering.

Bifunctional catalyst↗
DOE OSTI2022

Effects of oxygen on the adsorption/oxidation of aqueous Sb(III) by Fe-loaded biochar: An X-ray absorption spectroscopy study

Fe-loaded biochar (FeBC) has been considered for Sb(III) adsorption, but the effects of oxygen (O 2 ) on the adsorption need further investigation. Liquid-/solid-phase analyses were conducted to investigate the role of O 2 in the Sb(III) adsorption by FeBC. The adsorption was best described by the pseudo-second-order (PSO) model for kinetic results and by the Langmuir model for thermodynamic results. More than 96.8 % of Sb(III) was adsorbed by FeBC, and available O 2 increased the liquid-phase Sb(III) oxidation efficiency by 2.1–7.5 times. The peak changes at ~1640 and 3450 cm -1 in FTIR spectra indicated the occurrence of inner-sphere complexation between Sb(III)/Sb(V) and hydroxyl (–OH)/carboxyl (–COOH) groups in FeBC under aerobic and anaerobic conditions. Fe/Sb X-ray absorption spectroscopy (XAS) analysis results showed aqueous Sb(III) complexed to the edge-sharing Fe(III)-O-Fe(III) in FeBC. Regardless of whether O 2 was available or not, solid-phase edge-sharing Fe(III)-O-Sb(V) complexes (~3.05 Å), which had lower toxicity and migration ability than aqueous Sb(III), formed through a ligand-to-metal charge-transfer (LMCT) process. More than 91 % of adsorbed Sb(III) was oxidized to edge-sharing Fe(III)-O-Sb(V) complexes in 3 h. Additionally, the Sb(V) from liquid-phase oxidation could also directly complex to the Fe(III)-O-Fe(III) and form edge-sharing Fe(III)-O-Sb(V) complexes. Here these results provide evidence to inform further FeBC application for the Sb-contaminated water treatment.

54 ENVIRONMENTAL SCIENCES↗