Search NASA⌕ Search

SEARCH · Search NASA

Results for “CMP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Particle dynamics of nanoplastics suspended in water with soil microparticles: insights from small angle neutron scattering (SANS) and ultra-SANS

Small-angle neutron scattering (SANS) and ultra-SANS (USANS) were employed to understand the aggregation behavior and observe the size reduction for nanoplastics (NPs) formed from a biodegradable mulch film, and microparticles of vermiculite (V), an artificial soil, suspended in water in the presence of low convective shear (ex situ stirring) prior to measurements. Neutron contrast matching was employed to minimize the signal of V (by 100-fold) and thereby isolate the signal due to NPs in the neutron beam, as the contrast match point (CMP) for V (67 vol% deuteration of water) differed from that of NPs by more than 20%. The original NPs' size distribution was bimodal: <200 nm and 500–1200 nm, referred to as small and large NPs, i.e., SNPs and LNPs, respectively. In the absence of V, SNPs formed homoaggregates at higher concentrations that decreased with stirring time, while the size of LNPs remained unchanged. The presence of V at 2-fold lower concentration than NPs did not change the size of SNPs but reduced the size of LNPs by nearly 2-fold as stirring time increased. Because the size of SNPs and LNPs did not differ substantially between CMP and 100% D 2 O solvents, it is evident that SNPs and LNPs are mainly composed of NPs and not V. In conclusion, the results suggest that LNPs are susceptible to size reduction through collisions with soil microparticles via convection, yielding SNPs near soil–water interfaces within vadose zones.

Nanoplastics↗

Nitrogen K-edge x-ray absorption near edge structure of pyrimidine-containing nucleotides in aqueous solution

X-ray absorption near edge structure (XANES) was measured at energies around the N K-edge of the pyrimidine-containing nucleotides, cytidine 5′-monophosphate (CMP), 2′-deoxythymidine 5′-monophosphate (dTMP), and uridine 5′-monophosphate (UMP), in aqueous solutions and in dried films under various pH conditions. The features of resonant excitations below the N K-edge in the XANES spectra for CMP, dTMP, and UMP changed depending on the pH of the solutions. The spectral change thus observed is systematically explained by the chemical shift of the core-levels of N atoms in the nucleobase moieties caused by structural changes due to protonation or deprotonation at different proton concentrations. This interpretation is supported by the results of theoretical calculations using density functional theory for the corresponding nucleobases in the neutral and protonated or deprotonated forms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Accurate Efficiency Measurements for Emerging PV: A Comparison of NREL's Steady-State Performance Calibration Protocol Between Conventional and Emerging PV Technologies

Emerging PV technologies (e.g. Perovskite, and Quantum Dot) are commonly known to possess challenges for accurate performance measurement under the existing IEC 60904 series of standards, which were developed for conventional Si solar cells. Potential performance artifacts depending on scan rates and directions and light bias exposure history are often seen in those emerging solar cells. To avoid these artifacts and provide an unbiased and reliable efficiency measurement, NREL's Cell and Module Performance (CMP) Group has developed a steady-state performance calibration protocol - the asymptotic P MAX method. In this paper, we applied this procedure to four PV cell technologies, Si, CIGS, perovskite, and Quantum Dot (QD), and compared their performance variations between the transient and the steady-state conditions. By comparison, we found that the performance parameters ( i.e. V OC , I SC , FF, ..eta..) measured between fast I-V scans (and the asymptotic method (steady-state) change significantly for perovskite and QD cells. These changes do not happen for Si and CIGS cells. Furthermore, the statistical performance analysis on nearly 100 emerging cells received globally (including OPV, Perovskite, and QD) shows that over 70 % of the fast I-V scans have a relative performance deviation larger than 1% compared to those determined using the asymptotic P MAX scan. Given the complex dynamic behavior observed in emerging PV devices, the CMP group at NREL thus only certifies their steady steady-state performance using the Asymptotic P MAX method. We highly recommend similar steady-state performance calibration protocol for all researchers in emerging PV because accuracy in reported efficiencies is critical to the long-term success of those promising new PV technologies.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Particle size and surfactant effects on chemical mechanical polishing of glass using silica-based slurry

This study explores the effect of particle size and surfactant on the chemical mechanical polishing (CMP) of glass using colloidal silica-based slurry. It was found that the material removal rate strongly depends on the particle size and the types of surfactants and that the rms roughness was independent of particle size and correlated to surfactants. On the basis of polishing results, it was concluded that the main polishing mechanism was changed from indentation mechanism to surface-area mechanism, with the variation of particle size. In addition, the molecular structure, charge type, and lubricating effect of the surfactants play an important role in the dispersion of abrasive particles and in the CMP performance.

36 MATERIALS SCIENCE↗

Post-Closure Inspection and Monitoring Report for Corrective Action Unit 417: Central Nevada Test Area Surface, Hot Creek Valley, Nevada

This report presents results of data collected during the annual post-closure site inspection conducted at the Central Nevada Test Area, surface Corrective Action Unit (CAU) 417 in June 2009. The annual post-closure site inspection included inspections of the UC-1, UC-3, and UC-4 sites in accordance with the Post-Closure Monitoring Plan provided in the CAU 417 Closure Report (NNSA/NV 2001). The annual inspection conducted at the UC-1 Central Mud Pit (CMP) indicated that the site and soil cover were in good condition. Three new fractures were identified in the soil cover and were filled with bentonite chips during the inspection. The vegetation on the soil cover was adequate but showed signs of the area's ongoing drought. No issues were identified with the CMP fence, gate, or subsidence monuments. No issues were identified with the warning signs and monuments at the other two UC-1 locations

54 ENVIRONMENTAL SCIENCES↗

Phase I - Smart Grid Data Access Pilot Program: Utilizing STEM Education as a Catalyst for Residential Consumer Decision Making and Change

Under Phase I of the Smart Grid Data Access Pilot Program, the Gulf of Maine Research Institute (GMRI) partnered with Central Maine Power (CMP), and the Maine Mathematics and Science Alliance (MMSA) and engaged key vendors Tilson Government Services, LLC (Tilson), and Image Works to demonstrate the efficacy of PowerHouse, an interactive online learning environment linking middle school students with their home electricity consumption data provided through CMP’s Advanced Metering Infrastructure (AMI). The goal of the program is to harness the power of youth to alter home energy consumption behaviors using AMI data. Successful programs aimed at smoking cessation, recycling, and seat belt use have demonstrated the power of young people to influence household behaviors. In an era of increasing concern about energy costs, availability, and human impacts on global climate, GMRI sought to demonstrate the effectiveness of a student-focused approach to understanding and managing household energy use. We also sought to contribute to a solid foundation of science-literate students who can analyze evidence to find solutions to increasingly complex energy challenges.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

PNNL 2017 Richland Campus Master Plan

Based in Richland, Washington, Pacific Northwest National Laboratory (PNNL) is one of 10 United States (U.S.) Department of Energy (DOE) Office of Science (SC) national laboratories. PNNL is DOE’s premier chemistry, earth sciences and data analytics Laboratory, delivering vital mission impacts in energy resiliency and national security. PNNL has 19 core capabilities, each a powerful combination of world-class staff, state-of-the-art equipment, and mission ready facilities. These capabilities represent a collective set of skills and a body of world-leading scientific and engineering work that provides exceptional value and mission delivery to DOE, the National Nuclear Security Administration (NNSA), the U.S. Department of Homeland Security (DHS), and the missions of other federal agencies and industry through strategic partnership projects. Operated by Battelle Memorial Institute (Battelle), PNNL has more than: 2.3 million gross square feet and 4,400 staff members. PNNL is implementing a rolling 10-year campus strategy (initiated in FY 2013) designed to deliver the foundation for the multidisciplinary science and engineering expertise, equipment, instrumentation, facilities, and infrastructure required to continue providing exceptional value and mission delivery. PNNL’s annual ten-year plan is published with SC’s Ten-Year Plans for the Science National Laboratories. The most recent publication is available at: https://science.energy.gov/lp/laboratory-planning-process/. This edition of the PNNL Richland Campus Master Plan (CMP) is an update to the 2012 CMP.

99 GENERAL AND MISCELLANEOUS↗

Post-Closure Inspection and Monitoring Report for Surface Corrective Action Unit 417 at the Central Nevada Test Area, Nevada, Site

This report presents results of data collected during the biennial post-closure site inspections conducted in July 2014 at the surface Corrective Action Unit (CAU) 417 at the Central Nevada Test Area, Nevada, site. The every-other-year post-closure site inspections included inspections of the UC-1, UC-3, and UC-4 sites in accordance with the Post-Closure Monitoring Plan provided in the CAU 417 Closure Report (NNSA/NV 2001). The biennial inspection conducted at the UC-1 Central Mud Pit (CMP) indicated that the site and soil cover were in good condition. No new fractures or extensions of existing fractures were observed and no issues with the fence or gate were identified. The vegetation on the cover continues to be healthy. Precipitation measured from July 1, 2012, through June 30, 2013, totaled 179.6 millimeters (mm) or 7.1 inches. Precipitation measured from July 1, 2013, through June 3, 2014, totaled 157.0 mm or 6.2 inches. Soil moisture content data show that the UC-1 CMP cover is performing as designed, and vapotranspiration is effectively removing water from the cover.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Core Model Proposal #399: Updating the SSP Database (v3.0) (Population, GDP, and Labor Force) and Labor Productivity (KLEM)

This Core Model Proposal (CMP) updates the Shared Socioeconomic Pathway (SSP) database to a recent version (v3.0.1; released in 2024) within GCAM. Currently, GCAM relies on socioeconomic drivers, including population, GDP, and labor force projections, from the original SSP database version released in 2013. These projections, provided by independent socioeconomic dynamic models (e.g., multi-dimensional demographic models and macroeconomic models of convergence growth), may need regular updates when (1) near-term observations become available and (2) there are updates and advancements in the socioeconomic modeling. Timely updates of socioeconomic drivers in global economic equilibrium and multisector dynamic modeling will ensure (1) alignment of historical years and near-term projections with observations, enhancing base year calibrations, including calibration parameters and labor productivity, and (2) improvement of long-term projections with updated socioeconomic drivers, which set the scale of the economy. This CMP updates the SSP data (from v2013 to v2024) and also fixes/reconciles historical GDP data sources in GCAM. We investigate the impact of these updates on GCAM projections.

97 MATHEMATICS AND COMPUTING↗

Core Model Proposal #: 374 Global Iron and Steel Trade

This core model proposal (CMP) enables GCAM to track the gross trade of regional iron and steel commodities. Following the logit-based Armington trade modeling framework, this CMP aims to improve the representation of physical output (Mt) flows in GCAM v6.0’s iron and steel sector. In addition, the core model proposal also updates the regional steel demand and improves the representation of iron and steel technologies (and their energy coefficients) across all GCAM regions.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Results from a 'small box' realtime molecular contamination monitor on STS-3

On the basis of early estimates of the Shuttle induced environment, Scialdone (1979) concluded that in the vicinity of the cargo, the cargo would have the largest influence on the environment. As a contamination control device, realtime monitors can indicate safe operational periods for sensitive attached payloads. It was, therefore, decided to develop the OSS-1/Contamination Monitor Package (CMP) experiment which was seen as a forerunner of an operational monitor. A description of the CMP is provided, taking into account four actively temperature controlled quartz crystal microbalances (TQCM). The TQCM temperatures could be varied from -60 C to +80 C. The sensor consisted of a matched pair of quartz crystals. The crystals were designated as a sensor and reference crystal. Results obtained during the STS-3 mission are discussed. These results show the feasibility and advantages of a small real-time contamination monitor.

Triolo, J.↗

SPOT satellite family: Past, present, and future of the operations in the mission and control center

SPOT sun-synchronous remote sensing satellites are operated by CNES since February 1986. Today, the SPOT mission and control center (CCM) operates SPOT1, SPOT2, and is ready to operate SPOT3. During these seven years, the way to operate changed and the CCM, initially designed for the control of one satellite, has been modified and upgraded to support these new operating modes. All these events have shown the performances and the limits of the system. A new generation of satellite (SPOT4) will continue the remote sensing mission during the second half of the 90's. Its design takes into account the experience of the first generation and supports several improvements. A new generation of control center (CMP) has been developed and improves the efficiency, quality, and reliability of the operations. The CMP is designed for operating two satellites at the same time during launching, in-orbit testing, and operating phases. It supports several automatic procedures and improves data retrieval and reporting.

Philippe, Pacholczyk↗

Cryogenic Information Center

The Cryogenic Information Center (CIC) is a not-for-profit corporation dedicated to preserving and distributing cryogenic information to government, industry, and academia. The heart of the CIC is a uniform source of cryogenic data including analyses, design, materials and processes, and test information traceable back to the Cryogenic Data Center of the former National Bureau of Standards. The electronic database is a national treasure containing over 146,000 specific bibliographic citations of cryogenic literature and thermophysical property data dating back to 1829. A new technical/bibliographic inquiry service can perform searches and technical analyses. The Cryogenic Material Properties (CMP) Program consists of computer codes using empirical equations to determine thermophysical material properties with emphasis on the 4-300K range. CMP's objective is to develop a user-friendly standard material property database using the best available data so government and industry can conduct more accurate analyses. The CIC serves to benefit researchers, engineers, and technologists in cryogenics and cryogenic engineering, whether they are new or experienced in the field.

Mohling, Robert A.↗

Cryogenic Information Center

The Cryogenic Information Center (CIC) is a not-for-profit corporation dedicated to preserving and distributing cryogenic information to government, industry, and academia. The heart of the CIC is a uniform source of cryogenic data including analyses, design, materials and processes, and test information traceable back to the Cryogenic Data Center of the former National Bureau of Standards. The electronic database is a national treasure containing over 146,000 specific bibliographic citations of cryogenic literature and thermophysical property data dating back to 1829. A new technical/bibliographic inquiry service can perform searches and technical analyses. The Cryogenic Material Properties (CMP) Program consists of computer codes using empirical equations to determine thermophysical material properties with emphasis on the 4-300K range. CMP's objective is to develop a user-friendly standard material property database using the best available data so government and industry can conduct more accurate analyses. The CIC serves to benefit researchers, engineers, and technologists in cryogenics and cryogenic engineering, whether they are new or experienced in the field.

Mohling, Robert A.↗

Analysis of TRMM Microphysical Measurements: Tropical Rainfall Measuring Mission (TRMM)

SPEC Incorporated participated in three of the four TRMM field campaigns (TEFLUN-A, TEFLUN-B and KWAJEX), installing and operating a cloud particle imager (CPI) and a high volume precipitation spectrometer (HVPS) on the SPEC Learjet in TEFLUN-A, the University of North Dakota Citation in TEFLUN-B and KWAJEX, and a CPI on the NASA DC-8 in KWAJEX. This report presents and discusses new software tools and algorithms that were developed to analyze microphysical data collected during these field campaigns, as well as scientific interpretations of the data themselves. Software algorithms were developed to improve the analysis of microphysical measurements collected by the TRMM aircraft during the field campaigns. Particular attention was paid to developing and/or improving algorithms used to compute particle size distributions and ice water content. Software was also developed in support of production of the TRMM Common Microphysical Product (CMP) data files. CMP data files for TEFLUN-A field campaign were produced and submitted to the DAAC. Typical microphysical properties of convective and stratiform regions from TEFLUN-A and KWAJEX clouds were produced. In general, it was found that in the upper cloud region near -20 to -25 C, stratiform clouds contain very high (greater than 1 per cubic centimeter) concentrations of small ice particles, which are suspected to be a residual from homogeneous freezing and sedimentation of small drops in a convective updraft. In the upper cloud region near -20 to -25 C, convective clouds contain aggregates, which are not found lower in the cloud. Stratiform clouds contain aggregates at all levels, with the majority in the lowest levels. Convective cloud regions contain much higher LWC and drop concentrations than stratiform regions at all levels, and higher LWC in the middle and upper regions. Stratiform clouds contain higher IWC than convective clouds only at the lowest level. Irregular shaped ice particles are found in very high concentrations throughout both convective and stratiform cloud regions. A striking difference in particle shape in cirrus formed in situ, cirrus formed from maritime anvils and cirrus formed from continental anvils. Over 50% of the mass of in situ cirrus ice particles is composed of bullet rosettes, while bullet rosettes are virtually non-existent in maritime and tropical anvils. Tropical anvils are composed of mostly singular, plates, capped columns, and blocky irregular shapes, while continental anvils have a much higher percentage of aggregates, some of which are chains of small spheroidal particles that appear to result from homogeneous freezing of drops. A correlation between high electric fields in continental anvils and the formation of aggregates is hypothesized.

Source record↗

Growing Aligned Carbon Nanotubes for Interconnections in ICs

A process for growing multiwalled carbon nanotubes anchored at specified locations and aligned along specified directions has been invented. Typically, one would grow a number of the nanotubes oriented perpendicularly to a silicon integrated-circuit (IC) substrate, starting from (and anchored on) patterned catalytic spots on the substrate. Such arrays of perpendicular carbon nanotubes could be used as electrical interconnections between levels of multilevel ICs. The process (see Figure 1) begins with the formation of a layer, a few hundred nanometers thick, of a compatible electrically insulating material (e.g., SiO(x) or Si(y)N(z) on the silicon substrate. A patterned film of a suitable electrical conductor (Al, Mo, Cr, Ti, Ta, Pt, Ir, or doped Si), having a thickness between 1 nm and 2 m, is deposited on the insulating layer to form the IC conductor pattern. Next, a catalytic material (usually, Ni, Fe, or Co) is deposited to a thickness between 1 and 30 nm on the spots from which it is desired to grow carbon nanotubes. The carbon nanotubes are grown by plasma-enhanced chemical vapor deposition (PECVD). Unlike the matted and tangled carbon nanotubes grown by thermal CVD, the carbon nanotubes grown by PECVD are perpendicular and freestanding because an electric field perpendicular to the substrate is used in PECVD. Next, the free space between the carbon nanotubes is filled with SiO2 by means of CVD from tetraethylorthosilicate (TEOS), thereby forming an array of carbon nanotubes embedded in SiO2. Chemical mechanical polishing (CMP) is then performed to remove excess SiO2 and form a flat-top surface in which the outer ends of the carbon nanotubes are exposed. Optionally, depending on the application, metal lines to connect selected ends of carbon nanotubes may be deposited on the top surface. The top part of Figure 2 is a scanning electron micrograph (SEM) of carbon nanotubes grown, as described above, on catalytic spots of about 100 nm diameter patterned by electron-beam lithography. These and other nanotubes were found to have lengths ranging from 2 to 10 m and diameters ranging from 30 to 200 nm, the exact values of length depending on growth times and conditions and the exact values of diameter depending on the diameters and thicknesses of the catalyst spots. The bottom part of Figure 2 is an SEM of an embedded array of carbon nanotubes after CMP.

Li, Jun↗

Applications of Hyporheic Zone Sampling for Assessing VOC Plume Engineered Remediation and Natural Attenuation Effectiveness - 20414

Determining the efficacy of engineered remedial actions and/or natural attenuation as an acceptable EPA Record of Decision (ROD) must address long-term temporal and spatial variability. Since final plume downslope destinations are aquifers and related surface streams and rivers, hyporheic zone sampling is essential. Comprehensive hyporheic sampling documents plume groundwater remediation prior to upwelling into stream benthic strata and natural attenuation within this dynamic zone itself. Our intensive sampling of the Savannah River Site (SRS) Chemical, Metals, and Pesticides (CMP) Pits VOC plume-fringe from 2005 to 2018 documented PCE natural attenuation and effectiveness of In Situ Thermal Treatment (ISTT). Most plume hyporheic upwelling was delimited to a 20 m inflow reach along Pen Branch. Our study utilized corroborative sampling methodologies: ambient hole-water grab samples: passive diffusion bags (PDB); and hole-core sediment samples to confirm station to station spatial and temporal trends. VOC hot spot detections were confirmed from both groundwater and soil core samples. VOC pathways through the Pen Branch hyporheic zone were assessed at hole-installation using sequential soil samples from augered cores and grab-samples of hole-bottom water. Longer term, composite water samples were collected from PDBs deployed for a minimum two-week equilibration period. Soil samples were collected from the 15 and 65 cm core levels in December 2017 and June 2018 at six stations. Additional core depths of 40 and 85 cm were sampled in June 2018 at the highest VOC station (5DB80). All samples were analyzed in an EPA certified lab by purge and trap GC-MS. Effectiveness of previous ISTT and soil vapor extraction (SVE) for this CMP Pits PCE plume, was clearly documented by significant downward trends in VOC at hyporheic zone stations prior to December 2015. Achieving final stage conversions of PCE daughter products to ethene and CO{sub 2} may be limited depending upon suitable interactions between hyporheic zone sediment morphology, hydrology, and redox conditions. Because declines in VOC daughter products at our hyporheic stations may also be caused by physical actions of dilution and dispersion rather than true biochemical dechlorination, full quantification of natural attenuation requires the use of compound-specific isotope ratio analysis (CSIA) and microbial 16S rRNA with qPCR. To assist these next-phase efforts, a natural attenuation index (NAI) was used to help produce quicker, more cost-effective decision making for locating CSIA and microbial sampling efforts. The NAI used natural logarithm transformed GC-MS results for station VOC degradation compounds versus VOC parent compounds. Wide differences were observed between stations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Crystal structures of sialyltransferase from Photobacterium damselae

Sialyltransferase structures fall into either GT-A or GT-B glycosyltransferase fold. Some sialyltransferases from the Photobacterium genus have been shown to contain an additional N-terminal immunoglobulin (Ig)-like domain. Photobacterium damselae α2–6-sialyltransferase has been used efficiently in enzymatic and chemoenzymatic synthesis of α2–6-linked sialosides. In this paper, we report three crystal structures of this enzyme. Two structures with and without a donor substrate analog CMP-3F(a)Neu5Ac contain an immunoglobulin (Ig)-like domain and adopt the GT-B sialyltransferase fold. The binary structure reveals a non-productive pre-Michaelis complex, which are caused by crystal lattice contacts that prevent the large conformational changes. The third structure lacks the Ig-domain. Finally, comparison of the three structures reveals small inherent flexibility between the two Rossmann-like domains of the GT-B fold.

59 BASIC BIOLOGICAL SCIENCES↗