Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONICAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Theoretical pressure distribution and wave drags for conical boattails

Afterbody pressure distributions and wave drag were calculated using a second-order theory for a variety of conical boattails at zero angle of attack. Results are presented for Mach numbers from 1.5 to 4.5, area ratios from 0.200 to 0.800, and boattail angle from 3 degrees to 11 degrees. The results indicate that for a given boattail angle, the wave drag decreases with increasing Mach number and area ratio. The wave drag, for a constant area ratio, increases with increasing boattail angle. For a specific Mach number, area ratio, and fineness ratio, a comparison of the wave-drag coefficients for conical, tangent-parabolic, and secant-parabolic boattails showed the conical boattail to have the smallest wave drag.

Jack, John R↗
NASA NTRS1958

Heat-Transfer Measurements in Free Flight at Mach Numbers up to 14.6 on a Flat-Faced Conical Nose with a Total Angle of 29 Degrees

Skin-temperature measurements have been made at several locations on a flat-faced cone-cylinder nose which was flight tested on a fivestage rocket-propeller model to a Mach number of 14.64 and a free-stream Reynolds number of 2.0 x 10(exp 6), based on flat-face diameter, at an altitude of 66,300 feet. The copper nose had a 29 deg total-angle conical section which was 1.6 flat-face diameters long. The aerodynamic-heating rates determined from the temperature measurements reached 1,440 Btu/( sec) (sq ft) on the flat face. The heating rates near the center of the flat face agreed well at Mach numbers up to 13.6 with those obtained by a theory for laminar stagnation-point heating in equilibrium dissociated air (Avco Res. Rep. 1). At Mach numbers above 13.6, the heating rates at locations near the center of the flat face became progressively lower than stagnation-point theory and. were 29 percent lower at Mach number 14.6 at the end. of the test. The reason for this behavior of the heating on the central part of the flat face was not determined. Excluding the relatively low heating rates that occurred on the central part of the nose at the highest Mach numbers, the distribution of experimental heating along the innermost 0.79 of the flat-face radius, expressed as a percentage of stagnation-point heating, was in fair agreement with the distribution predicted by laminar theory. At a location of 0.71 radii from the stagnation point, the experimental heating was very near 130 percent of the theoretical stagnation-point rate at Mach numbers from 11 to 14.5. The experimental beating rates on the conical section of the nose were in good agreement with laminar-cone theory using the assumption of theoretical sharp-cone static pressure on the conical section.

Rumsey, Charles B↗
NASA NTRS1958

Lift, Drag, and Pitching Moment of an Aspect-Ratio-2 Triangular Wing with Leading-Edge Flaps Designed to Simulate Conical Camber

An investigation was conducted to determine the effectiveness of leading-edge flaps in reducing the drag at lifting conditions of a triangular wing of aspect ratio 2.0. The flaps, deflected to simulate conically cambered wings having a wide range of design lift coefficients, were tested over a Mach number range of 0.70 to 2.22 through an angle-of-attack variation from -6 deg to +18 deg at a constant Reynolds number of 3.68 million based on the wing mean aerodynamic chord. A symmetrical wing of the same plan form and aspect ratio was also tested to provide a basis for comparison. The experimental results showed that with the flaps in the undeflected position, a small amount of fixed leading-edge droop incorporated over the outboard 5 percent of the wing semispan was as effective at high subsonic speeds as conical camber in improving the maximum lift-drag ratio above that of the symmetrical wing. At supersonic speeds, the penalty in minimum drag above that of the symmetrical wing was less than that incurred by conical camber. Deflecting the leading-edge flaps about the hinge line through 80 percent of the wing semispan resulted in further improvements of the drag characteristics at lift coefficients above 0.20 throughout the Mach number range investigated. The lift and pitching-moment characteristics were not significantly affected by the leading-edge flaps.

Menees, Gene P.↗
NASA NTRS1958

Stability of Cylindrical and Conical Shells of Circular Cross Section, with Simultaneous Action of Axial Compression and External Normal Pressure

We consider in this report the determination of the upper limit of critical loads in the case of simultaneous action of a compressive force, uniformly distributed over plane cross sections, and of isotropic external normal pressure on cylindrical or conical shells of circular cross section. As a starting point we use the differential equations for neutral equilibrium of conical shells which have been used for the solution of the problem of stability of conical shells under torsion and under axial compression; upon solution of the problem it is possible to satisfy all boundary conditions, in contrast to the report where no attention is paid to the fulfillment of the boundary conditions, and to the report where only part of the boundary conditions are satisfied by solution of the problem according to Galerkin's method. Approximate formulas are used for the determination of the critical external normal pressure with simultaneous action of longituninal compression. Let us note that the formulas suggested in reference 5 are not well founded and may lead, in a number of cases, to a substantial mistake in the magnitude of the critical load.

Mushtari, K. M.↗
NASA NTRS2007

Comparison of a Simple Patched Conic Trajectory Code to Commercially Available Software

Often in spaceflight proposal development, mission designers must eva luate numerous trajectories as different design factors are investiga ted. Although there are numerous commercial software packages availab le to help develop and analyze trajectories, most take a significant amount of time to develop the trajectory itself, which isn't effectiv e when working on proposals. Thus a new code, PatCon, which is both q uick and easy to use, was developed to aid mission designers to condu ct trade studies on launch and arrival times for any given target pla net. The code is able to run quick analyses, due to the incorporation of the patched conic approximation, to determine the trajectory. PatCon provides a simple but accurate approximation of the four body moti on problem that would be needed to solve any planetary trajectory. P atCon has been compared to a patched conic test case for verification, with limited validation or comparison with other COTS software. This paper describes the patched conic technique and its implementation i n PatCon. A description of the results and comparison of PatCon to ot her more evolved codes such as AGI#s Satellite Tool Kit and JAQAR As trodynamics# Swingby Calculator is provided. The results will include percent differences in values such as C3 numbers, and Vinfinity at a rrival, and other more subjective results such as the time it takes to build the simulation, and actual calculation time.

AndersonPark, Brooke M.↗
NASA NTRS2007

Current sheet Formation in a Conical Theta Pinch Faraday Accelerator with Radio-Frequency Assisted Discharge

The inductive formation of current sheets in a conical theta pinch FARAD (Faraday Accelerator with Radio-frequency Assisted Discharge) thruster is investigated experimentally with time-integrated photography. The goal is to help in understanding the mechanisms and conditions controlling the strength and extent of the current sheet, which are two indices important for FARAD as a propulsion concept. The profiles of these two indices along the inside walls of the conical acceleration coil are assumed to be related to the profiles of the strength and extent of the luminosity pattern derived from photographs of the discharge. The variations of these profiles as a function of uniform back-fill neutral pressure (with no background magnetic field and all parameters held constant) provided the first clues on the nature and qualitative dependencies of current sheet formation. It was found that there is an optimal pressure for which both indices reach a maximum and that the rate of change in these indices with pressure differs on either side of this optimal pressure. This allowed the inference that current sheet formation follows a Townsend-like breakdown mechanism modified by the existence of a finite pressure-dependent radio-frequency-generated electron density background. The observation that the effective location of the luminosity pattern favors the exit-half of the conical coil is explained as the result of the tendency of the inductive discharge circuit to operate near its minimal self-inductance. Movement of the peak in the luminosity pattern towards the upstream side of the cone with increasing pressure is believed to result from the need of the circuit to compensate for the increase in background plasma resistivity due to increasing pressure.

Hallock, Ashley K.↗
NASA NTRS2011

Conical Shock-Strength Determination on a Low-Sonic-Boom Aircraft Model by Doppler Global Velocimetry

A nonintrusive technique Doppler global velocimetry (DGV) was used to determine conical shock strengths on a supersonic-cruise low-boom aircraft model. The work was performed at approximately Mach 2 in the Unitary Plan Wind Tunnel. Water is added to the wind tunnel flow circuit, generating small ice particles used as seed particles for the laser-based velocimetry. DGV generates two-dimensional (2-D) maps of three components of velocity that span the oblique shock. Shock strength (i.e. fractional pressure increase) is determined from observation of the flow deflection angle across the shock in combination with the standard shock relations. Although DGV had conveniently and accurately determined shock strengths from the homogenous velocity fields behind 2-D planar shocks, the inhomogeneous 3-D velocity fields behind the conical shocks presented additional challenges. Shock strength measurements for the near-field conical nose shock were demonstrated and compared with previously-published static pressure probe data for the same model in the same wind tunnel. Fair agreement was found between the two sets of results.

Herring, Gregory C.↗
NASA NTRS2014

The Development of a Conical Composite Energy Absorber for Use in the Attenuation of Crash/Impact Loads

A design for a novel light-weight conical shaped energy absorbing (EA) composite subfloor structure is proposed. This composite EA is fabricated using repeated alternating patterns of a conical geometry to form long beam structures which can be implemented as aircraft subfloor keel beams or frame sections. The geometrical features of this conical design, along with the hybrid composite materials used in the manufacturing process give a strength tailored to achieve a constant 25-40 g sustained crush load, small peak crush loads and long stroke limits. This report will discuss the geometrical design and fabrication methods, along with results from static and dynamic crush testing of 12-in. long subcomponents.

Littell, Justin D.↗
NASA NTRS2024

EMIC Wave Energy Dissipation as a Source of O + Conics and Warm Plasma Cloak in the Earth's Inner Magnetosphere

This study focuses on a specific source of the O + conics and warm plasma cloak in the Earth's inner magnetosphere due to electromagnetic ion cyclotron (EMIC) wave energy dissipation. We analyze the EMIC wave event observed by Van Allen Probe-A in the early afternoon off equatorial magnetosphere on 18 November 2015, where the two dominant EMIC wave bands, He + -band and H + -band, were observed for ∼4 min. All the wave and plasma parameters, the DC magnetic field, and ion distributions needed for our analysis are taken from the Van Allen Probe-A observations during the event. The major results of our analysis are as follows. (a) The H + and He + heating by EMIC waves is negligible. (b) A strong heating of O + by the wave energy dissipation around the third, fifth, and sixth harmonics of the O + gyrofrequency is revealed, where the majority of energy dissipated goes into heating of O + with the energies ≲100 eV and pitch angles ∼20°–90°. The estimated energy deposition rate is ∼0.1–3.4 eV/s per O + , totaling to the deposition of ∼20–800 eV per O + during the event. (c) EMIC waves substantially contribute to the formation of O + conics and warm plasma cloak by heating the upgoing low-energy ionospheric O + because waves heat ions with the energies and pitch angles that are characteristic of conics and warm plasma cloak, and the energy deposition per O + is comparable to those characteristic energies.

Konstantin V. Gamayunov↗
NASA NTRS1962

BUCKLING OF CONICAL SHELLS UNDER EXTERNAL PRESSURE

It is shown that the initial and the buckled shapes of a certain element of a conical shell can be considered as similar to those of an element of a cylindrical shell of which the radius and length are conservatively determined. It is concluded that therefore the buckling pressure of the conical shell is equal to that of the comparable cylindrical shell. A simple method for finding the buckling pressure if it varies along a generatrix is also given.

CONICAL SHELL↗
NASA NTRS1970

Flutter, vibration, and buckling of truncated orthotropic conical shells with generalized elastic edge restraint

A theoretical investigation has been made of the flutter, vibration, and buckling of truncated conical shells with generalized elastic edge restraint. The shell analysis is of the classical Donnell type, in-plane inertias and structural damping are neglected, and the aerodynamic loading is represented by the inviscid two-dimensional quasi-steady approximation. An approximate solution is obtained by the generalized Galerkin method. The accuracy and limitations of the analysis are illustrated by comparing numerical results for buckling an vibration with results of other investigations for various boundary conditions, applied loads, and shell geometries and stiffness. Sufficient numerical results are presented to permit the determination of the flutter condition for simply supported isotropic conical shells for a wide range of cone angle, length-radius ration, and radius-thickness ratio. Results are also presented to indicate some effects of variations in edge restraint, applied loads, and ring or stringer stiffening.

Flutter↗
DOE OSTI2026

An SF 6 gas-insulated −500 kV DC conical insulator vacuum feedthrough

A test electrode was biased to −500 kV direct current (DC) by means of a novel SF 6 gas-insulated conical alumina insulator feedthrough. The design enables the extreme high vacuum conditions required by spin-polarized electron sources by reducing the photogun vacuum chamber volume compared to coaxial cylindrical insulators. In contrast to conventional inverted-insulator photogun designs that rely on solid dielectric interfaces for high-voltage terminations, the present design employs a pressurized SF 6 intervening volume between a conical alumina insulator and a modified commercial epoxy high-voltage cable receptacle. Here, this approach enables the use of commercially available cable hardware while extending the demonstrated operating voltage of solid feedthroughs. A maximum voltage of −500 kV was applied to a test electrode attached to the narrow end of the feedthrough inside a chamber filled with SF 6 at 170.3 kPa (10 psig) and later under vacuum to −259 kV, limited by field emission. The results demonstrate that a commercial high-voltage cable combined with a custom-designed SF 6 gas-insulated vacuum feedthrough can be used to bias photogun electrodes to −500 kV DC.

Palacios-Serrano, Gabriel [Thomas Jefferson Nation↗
DOE OSTI2025

Conical intersections shed light on hot carrier cooling in quantum dots

Experimental observations of vibronic coherences in electronically excited colloidal semiconductor nanocrystals offer a window into the ultrafast dynamics of hot carrier cooling. In previous work, we showed that, in amine-passivated quantum dots (QDs), these coherences arise during relaxation through a cascade of conical intersections between electronically excited states. Here, in this work, we demonstrate the generality of this framework by application to QDs with surface-bound carboxylate ligands. A model involving a similar cascade of conical intersections accurately reproduces the frequencies of vibronic coherences observed with broadband multidimensional spectroscopy. The impact of ligands on the relaxation dynamics is attributed to two distinct mechanisms involving either electronic or vibrational coupling between the core and ligands. Compared to the amine-passivated QDs studied previously, the electronic coupling mechanism is less prominent in carboxylate-passivated QDs. Furthermore, comparison of acetate and formate ligands reveals that truncating the ligand alkyl chains alters the relaxation behavior predicted by the model.

14 SOLAR ENERGY↗
DOE OSTI2025

Analysis of the density field around a supersonic conical projectile using quantitative schlieren

Quantitative schlieren imaging is a flow measurement technique that is capable of measuring density fields throughout refractive flowfields. The technique was applied here to measure the density field surrounding supersonic conical projectiles in free flight. Shock waves attached to a supersonic conical projectile offer a simple geometry with the well-established Taylor–Maccoll analytical flow solution to which these experimental measurements were compared. The schlieren images recorded a projection of the index of refraction field surrounding the 10° half-angle cones which was converted to density first through an Abel inversion and then the Gladstone–Dale law. Three Abel inversion methods—two-point, three-point, and arbitrary ray axisymmetric projection (ARAP)—were applied to deconvolute the three-dimensional flow within the constrained axisymmetric flow field. The resulting reconstructed density profiles were compared to the Taylor–Maccoll solution, parameterized by cone geometry and Mach number. The experimental density fields demonstrated strong agreement with the theoretical profiles. Experimental consistency was confirmed across various projectile speeds, demonstrating quantitative schlieren’s capability to accurately reconstruct the density of the flow field, even within the resolution constraints imposed by high-speed imaging. In conclusion, an assessment of experimental uncertainties in the density reconstruction was performed.

Abel Inversion↗
DOE OSTI2026

Influence of conical wire array geometry on plasma flow and temperature profiles of radiatively cooled jets

The influence of conical wire array geometry on the formation and dynamics of pulsed-power driven plasma jets is investigated. In the experiments, the jet becomes isolated from the inflows as it passes through an aperture, allowing the study of its intrinsic evolution for different conical angles. Here, our results show that, regardless of the array opening angle, the jets are supersonic, highly collisional, and exhibit an exponential axial density decay with a characteristic scale length of 𝐿 𝑛 ≈ 3 mm, significantly shorter than the overall length of the jet. In contrast, axial velocity systematically increases with larger array opening angles. The near invariance of the density profile is attributed to a compensating mechanism between geometric divergence and axial acceleration, consistent with an asymptotically steady flow regime. Additionally, temperature measurements reveal ion-electron thermal decoupling near the base of the jet, with equilibration downstream. Analysis of radiative cooling and collisional energy exchange timescales indicates that the plasma evolves in a radiatively stable regime and that the two-temperature profile is fully described by the competition between both methods. These findings provide valuable information into the internal structure and evolution of pulsed-power plasma jets in regimes dominated by geometric shaping and radiative cooling, demonstrating experimental control over flow acceleration and collimation relevant to both laboratory and astrophysical contexts.

Physics - Plasma physics↗
NASA NTRS1970

Overlapped conic simulation of three-body trajectories

Trajectory computation technique for three-body motion is based on analytical derivation and empirical validation of pseudostate theory. Application of technique yields ''overlapped conic'' trajectories with error magnitudes only 20 percent as great as those of patched conic trajectories.

Wilson, S. W., Jr.↗
NASA NTRS1972

Analytical investigation of conical diffusers

A study was made to determine if existing data for straight-channel single-plane divergence diffusers together with boundary-layer methods could be practically employed to predict conical diffuser performance in the high-speed flow regime. A semiempirical correlation technique, which uses the experimental performance of a straight-channel single-plane divergence diffuser, and a momentum integral boundary-layer method were employed to predict conical diffuser performance. Neither of these methods is applicable when the boundary layer separates. The momentum integral method was used to study the relative importance of various boundary layer parameters in correlating unstalled diffuser performance. Other investigators have found that the best diffuser performance occurs when the diffuser is operating in the transitory stall regime. Since the analytical methods presented in this report are not applicable after the point of boundary-layer separation, a criterion was established from examination of experimental tests which allows the designer to ascertain approximate diffuser performance in the transitory stall regime.

Means, J. L.↗