Search NASA⌕ Search

SEARCH · Search NASA

Results for “CORROSION PRODUCTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Effect of electrical field on TSA failure of cement-based materials

The impact of electrical field on the sulfate attack of cement-based materials at low temperatures was studied to rapidly detect Thaumasite Sulfate Attack (TSA) in the laboratory and in future engineering. Sulfate attack of cement paste with 30 wt% replacement of CaCO{sub 3} powder soaked in Na{sub 2}SO{sub 4} solution, MgSO{sub 4} solution, or CaSO{sub 4} solution was measured under the condition of 5 ± 2 °C when an electrical field was applied. Appearance changes and compressive strength of the samples were tested to evaluate the corrosion degree. Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR) and Raman Spectroscopic measurements were applied to study the microstructure of the corrosion product. The test results indicate that sample damage was obvious, compression strength declined rapidly, and ettringite and/or thaumasite were found in the corrosion product after applying the electrical field for 90 days. A muddy product with TSA characteristics was formed, and thaumasite composition was found in the corrosion product after applying the electrical field for 120 days when MgSO{sub 4} solution was used as the corrosion medium. It is confirmed that an electrical field can accelerate TSA failure in cement-based materials.

36 MATERIALS SCIENCE↗

EXAMINATION OF SHIPPING PACKAGE 9975-2130

Shipping package 9975-02130 was examined in K-Area following the identification of a nonconforming condition; the axial gap between the drum flange and upper fiberboard assembly exceeded the maximum allowed value of 1 inch. The average measured axial gap was 1.1 inches. The fiberboard assembly in this package contained moisture levels of {approx}14-24% wood moisture equivalent ({approx}12-19 wt%) This is moderately higher than typically seen in conforming packages, but not as high as seen on most packages which have exceeded the allowed axial gap. Small patches of mold were growing on portions of the lower fiber assembly, but the fiberboard appeared intact and with little apparent change in its integrity. The lead shield had a heavy layer of corrosion product, some of which flaked off easily. The thickness of several flakes was measured, and varied from 0.0016 to 0.0031 inch. However, additional corrosion product remained on the shield under the flaked regions, so the total thickness of corrosion product exceeds 0.0031 inch.

09 BIOMASS FUELS↗

Modeling pore corrosion in normally open gold- plated copper connectors.

The goal of this study is to model the electrical response of gold plated copper electrical contacts exposed to a mixed flowing gas stream consisting of air containing 10 ppb H{sub 2}S at 30 C and a relative humidity of 70%. This environment accelerates the attack normally observed in a light industrial environment (essentially a simplified version of the Battelle Class 2 environment). Corrosion rates were quantified by measuring the corrosion site density, size distribution, and the macroscopic electrical resistance of the aged surface as a function of exposure time. A pore corrosion numerical model was used to predict both the growth of copper sulfide corrosion product which blooms through defects in the gold layer and the resulting electrical contact resistance of the aged surface. Assumptions about the distribution of defects in the noble metal plating and the mechanism for how corrosion blooms affect electrical contact resistance were needed to complete the numerical model. Comparisons are made to the experimentally observed number density of corrosion sites, the size distribution of corrosion product blooms, and the cumulative probability distribution of the electrical contact resistance. Experimentally, the bloom site density increases as a function of time, whereas the bloom size distribution remains relatively independent of time. These two effects are included in the numerical model by adding a corrosion initiation probability proportional to the surface area along with a probability for bloom-growth extinction proportional to the corrosion product bloom volume. The cumulative probability distribution of electrical resistance becomes skewed as exposure time increases. While the electrical contact resistance increases as a function of time for a fraction of the bloom population, the median value remains relatively unchanged. In order to model this behavior, the resistance calculated for large blooms has been weighted more heavily.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Weathering Steel Under Thin Electrolyte Layer at Different Relative Humidity

The corrosion behavior of weathering steel under thin electrolyte layer (TEL) at different relative humidity (RH) was investigated by cathodic polarization, electrochemical impedance spectroscopy, electrochemical noise, SEM/EDS, XRD and Raman spectroscopy. The results indicate that during the initial stage, the corrosion rate increases as the RH decreases when the initial thickness of TEL is above 100 μm. During the middle and final corrosion stages, the corrosion behavior of weathering steel is influenced by RH, the initial thickness of TEL and corrosion product. The TEL corrosion is divided into three types, and a weathering steel corrosion model under TEL and bulk solution is also proposed.

36 MATERIALS SCIENCE↗

Effect of MgCl{sub 2} on the Corrosion Behavior of Copper Under Periodic Wet/Dry Cycle Condition

The corrosion behaviors of copper under periodic wet/dry cycle conditions were investigated. The characteristics of the corrosion product formed on copper were analyzed by x-ray diffraction, scanning electron microscopy, energy-dispersive spectroscopy, and in situ electrochemical impedance spectroscopy. Weight loss results showed that the corrosion of copper under an MgCl{sub 2} deposition condition was more severe than that under NaCl. The main corrosion products formed on the tested sample under NaCl deposition condition consisted of Cu{sub 2}Cl(OH){sub 3} and Cu{sub 2}O, while those under the MgCl{sub 2} deposition condition consisted of Cu{sub 2}Cl(OH){sub 3} and Mg{sub 2}(OH){sub 3}Cl·4H{sub 2}O. In the case of the NaCl deposition condition, a two-layered structure formed during the corrosion process. However, the corrosion product layer formed on copper under the MgCl{sub 2} deposition condition had an extremely loose structure. The effect of MgCl{sub 2} on the corrosion mechanism of copper is discussed.

36 MATERIALS SCIENCE↗

Enhanced chemical CRUD decontamination combined with electrokinetic process - 15242

This study has tested about the deposition and dissolution of Chalk River Unidentified Deposit (CRUD), and investigated the remediation of CRUD. CRUD is an accumulated corrosion product on external fuel rod cladding surfaces and composed of either dissolved ions or solid particles such as Ni and Co. As nuclear power plants are getting older, decontaminating process has been concerned due to increased contamination. Corrosion product can be activated through nuclear reaction to form radionuclide such as Co-60. Because the CRUD is formed at cladding surface and radionuclides can be contained in CRUD, it can affect to human health and environment. Therefore CRUD needs to be removed safely during NPP's decontaminating process by efficient. In order to decontaminate the CRUD, first thing it has to be dissolved and removed. Deposition behavior of corrosion products has been well studied, but the study about behavior of CRUD dissolution is required in various environments. In this study, the CRUD synthesis, the dissolution method of CRUD, and the CRUD decontamination method was investigated. There are three major approaches the remediation of CRUD. First one is well synthesized the CRUD, second one is finding the optimum condition for CRUD dissolution, and last one is applying the Electro-Kinetic (EK) process to CRUD remediation. Synthesis of simulated CRUD for the decontamination experiments was successful. The combination of EK process with chemical decontamination of CRUD proved to be a more economical method for removing CRUD; it can be directly applied to the NPP decommissioning and decontamination process, and it can decrease the volume of secondary radioactive waste as well. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Anodic Role of Ni-Containing LPSO Phases During the Microgalvanic Corrosion of Mg{sub 98}Gd{sub 1.5}Ni{sub 0.5} Alloy

In the present study, the corrosion characteristics of cast Mg{sub 98}Gd{sub 1.5}Ni{sub 0.5} alloy with Ni-containing long-period stacking ordered (LPSO) structures were investigated. The results reveal that the Ni-containing LPSO phases were more active than the Mg matrix and preferentially eroded during the immersion process. This behavior indicates that the Ni-containing LPSO phases could have acted as microanodes, in contrast to the cathodic role of the Ni-free LPSO phases in other Mg alloys. Furthermore, the potential difference of approximately 600 mV between the phases accelerated the dissolution rate of the LPSO phase. Corrosion of the Mg matrix also occurred due to the inhomogeneous microstructure of the matrix. The synergetic corrosion between the Ni-containing LPSO phases and the enrichment of Cl{sup −} in the thick corrosion product films dominated the propagation of corrosion, which substantially deteriorated the corrosion resistance and accelerated the corrosion process of the Mg{sub 98}Gd{sub 1.5}Ni{sub 0.5} alloy.

36 MATERIALS SCIENCE↗

Application of wire beam electrode technique to investigate initiation and propagation of rebar corrosion

Multi-electrode technique named as wire beam electrode (WBE) was used to study pitting corrosion of rebar under concrete cover. When WBE embedded mortar sample was immersed in NaCl solution, uneven distributions of galvanic current and open circuit potential (OCP) on the WBE were observed due to the initiation of pitting corrosion. The following oxygen depletion in mortar facilitated the negative shift of the OCP and the smoothing of the current and potential distributions. Wetting–drying cycle experiments showed that corrosion products instead of oxygen in wet mortar specimen sustained the propagation of pitting corrosion due to Fe (III) taking part in cathodic depolarization during oxygen-deficient wet period, which was confirmed by micro-Raman spectroscopy. In addition, new pitting corrosion occurred mainly near the corrosion products, leading to preferentially horizontal propagation of rust layer on the WBE. A localized corrosion factor was further presented to quantify the localised corrosion based on galvanic current maps.

36 MATERIALS SCIENCE↗

Remedial Treatment of Corroded Iron Objects by Environmental Aeromonas Isolates

Using bacteria to transform reactive corrosion products into stable compounds represents an alternative to traditional methodsployed in iron conservation. Two environmental Aeromonas strains (CA23 and CU5) were used to transform ferric iron corrosion products (goethite and lepidocrocite) into stable ferrous iron-bearing minerals (vivianite and siderite). A genomic and transcriptomic approach was used to analyze the metabolic traits of these strains and to evaluate their pathogenic potential. Although genes involved in solid-phase iron reduction were identified, key genes present in other environmental iron-reducing species are missing from the genome of CU5. Several pathogenicity factors were identified in the genomes of both strains, but none of these was expressed under iron reduction conditions. Additional in vivo tests showed hemolytic and cytotoxic activities for strain CA23 but not for strain CU5. Both strains were easily inactivated using ethanol and heat. Nonetheless, given a lesser potential for a pathogenic lifestyle, CU5 is the most promising candidate for the development of a bio-based iron conservation method stabilizing iron corrosion. Based on all the results, a prototype treatment was established using archaeological items. On those, the conversion of reactive corrosion products and the formation of a homogenous layer of biogenic iron minerals were achieved. This study shows how naturally occurring microorganisms and their metabolic capabilities can be used to develop bio-inspired solutions to the problem of metal corrosion.

59 BASIC BIOLOGICAL SCIENCES↗

Incorporation of Pertechnetate and Perrhenate into Corroded Steel Surfaces Studied by X-ray Absorption Fine Structure Spectroscopy

Batch reaction experiments and solid-phase characterization analyses were completed to examine the uptake of dissolved perrhenate [Re(VII)] or pertechnetate [Tc(VII)] by A-516 steel coupons that corroded in simulated groundwater solutions or dilute water. The goal was to identify the mechanism(s) that control the uptake of 99Tc by corrosion products on carbon steel in the presence of dilute solutions. X-ray absorption fine structure spectroscopy (XAFS) was used to study the oxidation states of Re and Tc incorporated into the corroded steel coupon surfaces. X-ray fluorescence maps showed that the corroded coupons contain localized regions enriched in Re or Tc. The Re L3 near edge XAS results for the coupons reacted with Re-spiked waters were consistent with all sorbed Re being present as perrhenate and not significantly reduced to Re(IV). Linear combination fits of the EXAFS signals for the perrhenate and ReIVO2 standards indicate that Re sorbed to the steel coupons corroded in simulated J-13 (a relatively dilute Na-HCO3-CO3 groundwater) and even more dilute waters consists of a maximum of 5 and 10% Re(IV), respectively. The fluorescence results also showed that the Re concentrations increased with increasing time of exposure to the x-ray beam time, which suggests that the perrhenate ions are only weakly bonded to the matrix of the corrosion product. In contrast to the Re results, the Tc K edge XAFS results for the coupons reacted in 99Tc-spiked waters indicate that most of the sorbed Tc had been reduced to Tc(IV). The shape of the near edge and extended fine structure is similar to the Tc(IV)-hydrous ferric oxide (HFO) and not the TcO2-nH2O standard. Differences were noted in the XAS results for steel coupons reacted with waters spiked with 0.001 versus 0.1 mmol/L 99Tc in that much more of the sorbed Tc from 0.001 mmol/L 99Tc experiments was in the form of pertechnetate. Comparison of the XAS results for coupons reacted with 0.001 mmol/L 99Tc-spiked dilute simulated Na-HCO3-CO3 groundwater versus 0.001 mmol/L 99Tc-spiked dilute water also suggest that there are likely differences in the sorption mechanism for the pertechnetate fraction in the corrosion product which formed in these two test solutions. The cause for these differences is not known, but is likely due differences in the compositions of the dilute simulated Na-HCO3-CO3 groundwater and more dilute waters, such as the dissolved carbonate concentrations.

36 MATERIALS SCIENCE↗

Materials corrosion of high temperature alloys immersed in 600°C binary nitrate salt

Thirteen high temperature alloys were immersion tested in a 60/40 binary nitrate salt. Samples were interval tested up to 3000 hours at 600ÀC with air as the ullage gas. Chemical analysis of the molten salt indicated lower nitrite concentrations present in the salt, as predicted by the equilibrium equation. Corrosion rates were generally low for all alloys. Corrosion products were identified using x-ray diffraction and electron microprobe analysis. Fe-Cr based alloys tended to form mixtures of sodium and iron oxides, while Fe-Ni/Cr alloys had similar corrosion products plus oxides of nickel and chromium. Nickel based alloys primarily formed NiO, with chromium oxides near the oxide/base alloy interface. In625 exhibited similar corrosion performance in relation to previous tests, lending confidence in comparisons between past and present experiments. HA230 exhibited internal oxidation that consisted of a nickel/chromium oxide. Alloys with significant aluminum alloying tended to exhibit superior performance, due formation of a thin alumina layer. Soluble corrosion products of chromium, molybdenum, and tungsten were also formed and are thought to be a significant factor in alloy performance.

Kruizenga, Alan Michael↗

Corrosion Behavior of Fe-40at.%Al-Based Intermetallic in 0.25 M H{sub 2}SO{sub 4} Solution

The electrochemical behavior of Fe-40at.%Al-based intermetallic microalloyed with 3 and 5 at.% Cu additions in 0.25 M H{sub 2}SO{sub 4} solution over time was studied. A complementary study to characterize the surface morphology and semiquantitative chemical analysis of the corrosion products after 24 h of immersion was performed using scanning electron microscopy and x-ray energy dispersion spectrum. By means of electrochemical techniques, it was shown that Cu addition has a positive effect on corrosion resistance of Fe-40at.%Al-based intermetallic alloy. Additionally, the relatively high concentration of Cu consolidated the passive film of corrosion products and its stability.

36 MATERIALS SCIENCE↗

Oxidation-chlorination of binary Ni-Cr alloys in flowing Ar-O2-Cl2 gas mixtures at 1200 K

Nickel-chromium alloys are resistant to oxidation because of the selective oxidation of chromium to form a protective Cr2O3 scale. In chlorine-containing environments, volatile corrosion products can also be formed. The mixed oxidation-chlorination of Ni-4.5Cr, Ni-13.8Cr, and Ni-26.5Cr (by weight) alloys in Ar-O2-Cl2 gas mixtures is investigated using thermogravimetric analysis and atmospheric-pressure-sampling mass spectrometry, followed by examination of the corrosion products using scanning electron microscopy and X-ray diffraction analysis. The overall kinetics of the corrosion are affected by the relative amounts of oxides and chlorides formed and the composition of the oxide corrosion products.

Mcnallan, M. J.↗

Effect of Tempered Martensite and Ferrite/Bainite on Corrosion Behavior of Low Alloy Steel Used for Flexible Pipe Exposed to High-Temperature Brine Environment

Immersion experiments and electrochemical measurements were carried out to study the effect of tempered martensite and ferrite/bainite on corrosion behavior of low alloy steel used for flexible pipe exposed to high-temperature brine environment in terms of microstructure morphology, corrosion rate, corrosion products characteristics, potentiodynamic polarization curves and electrochemical impedance spectroscopy. The experimental results indicated that the proportion of high-angle grain boundaries of tempered martensite steel was greater than ferrite/bainite steel. The corrosion rate of ferrite/bainite steel was lower than tempered martensite steel. With increasing immersion time, the structure of corrosion products formed on the surface of ferrite/bainite steel was more compact and denser than tempered martensite steel. In addition, the current density of ferrite/bainite steel was lower than tempered martensite steel. The charge transfer resistance and total impedance of ferrite/bainite steel were larger than tempered martensite steel. Thus, the corrosion resistance of ferrite/bainite steel exposed to high-temperature brine environment was excellent compared to the tempered martensite steel.

36 MATERIALS SCIENCE↗

Electrochemical Behavior of Sn-9Zn-xTi Lead-Free Solders in Neutral 0.5M NaCl Solution

Electrochemical techniques were employed to study the electrochemical corrosion behavior of Sn-9Zn-xTi (x = 0, 0.05, 0.1, 0.2 wt.%) lead-free solders in neutral 0.5M NaCl solution, aiming to figure out the effect of Ti content on the corrosion properties of Sn-9Zn, providing information for the composition design of Sn-Zn-based lead-free solders from the perspective of corrosion. EIS results reveal that Ti addition was involved in the corrosion product layer and changed electrochemical interface behavior from charge transfer control process to diffusion control process. The trace amount of Ti addition (0.05 wt.%) can refine the microstructure and improve the corrosion resistance of Sn-9Zn solder, evidenced by much lower corrosion current density (i{sub corr}) and much higher total resistance (R{sub t}). Excess Ti addition (over 0.1 wt.%) led to the formation of Ti-containing IMCs, which were confirmed as Sn{sub 3}Ti{sub 2} and Sn{sub 5}Ti{sub 6}, deteriorating the corrosion resistance of Sn-9Zn-xTi solders. The main corrosion products were confirmed as Sn{sub 3}O(OH){sub 2}Cl{sub 2} mixed with small amount of chlorine/oxide Sn compounds.

36 MATERIALS SCIENCE↗

A Study on the Corrosion Behavior of Carbon Steel Exposed to a H{sub 2}S-Containing NH{sub 4}Cl Medium

NH{sub 4}Cl corrosion failure often occurs in the overhead systems of hydrotreaters, and this failure is always accompanied by the appearance of H{sub 2}S. A combination of electrochemical and surface spectroscopic (SEM/EDS, AFM, XRD) techniques was used to investigate the effect of different factors, including the surface roughness, temperature, dissolved oxygen, pH and H{sub 2}S concentration, on the corrosion behavior of carbon steel in an NH{sub 4}Cl environment with the presence of H{sub 2}S. The effect of H{sub 2}S concentrations (at the ppm level) on the corrosion behavior of carbon steel was systematically revealed. The experimental results clearly indicated that the corrosion rate reached a minimum value at 10 ppm H{sub 2}S. The steel surface was covered by a uniform corrosion product film in a 10 ppm H{sub 2}S environment, and the corrosion product film was tight and protective. The ammonia from NH{sub 4}Cl helped maintaining the protectiveness of the corrosion films in this environment. Dissolved oxygen mainly accelerated the cathodic reaction. The cathodic limiting current density increased with increasing temperature, and the anodic branch polarization curves were similar at different temperatures. The anodic current density decreased as the pH decreased, and the cathodic current density increased as the pH decreased. The absolute surface roughness (R{sub a}) of carbon steel increased from 132.856 nm at 72 h to 153.973 nm at 144 h, and the rougher surface resulted in a higher corrosion rate. The critical innovation in this research was that multiple influential factors were revealed in the NH{sub 4}Cl environment with the presence of H{sub 2}S.

36 MATERIALS SCIENCE↗

Corrosion Behavior of AZ31 Magnesium Alloy Produced by Continuous Variable Cross Section Direct Extrusion

In order to study the corrosion behavior of magnesium alloys of high performance in the simulated seawater by continuous variable cross section direct extrusion (CVCDE), an electrochemical method and weight loss method were used to study the difference between AZ31 magnesium alloys produced by CVCDE with different numbers of interim dies to examine the electrochemical corrosion behavior and corrosion rate at 3.5 wt.% NaCl solution in this paper. Scanning electron microscopy and x-ray diffraction were used to analyze the morphology of corrosion surfaces and the composition of the corrosion products of samples soaked for different times. The results show that after CVCDE with different numbers of interim dies, the size of the microstructure is refined gradually, and the grain orientation is also different; with the increase in the number of interim dies, the thermodynamic corrosion tendencies are different, and the corrosion resistance of samples extruded by conventional extrusion is relatively good; the charge transfer and material transfer process are the two main factors affecting the corrosion rate, which determines the direction of the electrochemical reaction; the corrosion form of the sample extruded by CVCDE is the local corrosion which is the filiform corrosion and pitting corrosion, and the corrosion product is mainly water-insoluble Mg(OH){sub 2}.

36 MATERIALS SCIENCE↗

Technical Note: Characterization of Corrosion Films Formed on Austenitic Stainless Steel in Supercritical CO 2 Containing H 2 O and O 2

Future technologies require structural alloys resistant to corrosion in supercritical CO 2 (sCO 2 ) fluids containing impurities such as H 2 O and O 2 . Traditional pipeline steels are potentially unsuitable for these environments and more corrosion resistant alloys such as stainless steels might be required. Little is known about the corrosion products formed on, and hence the processes which control corrosion of, stainless steels in impure sCO 2 environments. In this study, austenitic stainless steel 347H (UNS S34709) was exposed to sCO 2 containing H 2 O and O 2 at 8 MPa and 50°C or 250°C, and separately to the aqueous phase in equilibrium with the sCO 2 at 50°C, to simulate conditions expected in sCO 2 -based power cycles and carbon capture and storage pipelines. Only thin (< 20 nm) surface films formed after 500 h resulting in small mass changes and corrosion rates < 10 –4 mm/y, suggesting the material resists significant degradation in these environments. X-ray photoelectron spectroscopy and transmission electron microscopy were used to characterize the corrosion films in detail. Here, the exposure to the aqueous phase resulted in a thin (< 5 nm) Cr-oxide and/or -hydroxide passive film, while exposure to sCO 2 phases resulted in a multilayer Fe-rich oxide structure characteristic of a gas-phase oxidation process.

36 MATERIALS SCIENCE↗