Search NASA⌕ Search

SEARCH · Search NASA

Results for “COUNTING RATES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

A mercuric detector system for X-ray astronomy. 2. Results from flight tests of a balloon borne instrument

To establish the expected sensitivity of a new hard X-ray telescope design, an experiment was conducted to measure the background counting rate at balloon altitudes (40 km) of mercuric iodide, a room temperature solid state X-ray detector. The prototype detector consisted of two thin mercuric iodide (HgI2) detectors surrounded by a large bismuth germanate (Bi4Ge3O12) scintillator operated in anticoincidence. The bismuth germanate shield vetoed most of the background counting rate induced by atmospheric gamma-rays, neutrons and cosmic rays. A balloon-borne gondola containing a prototype detector assembly was designed, constructed and flown twice in the spring of 1982 from Palestine, Texas. The second flight of this instrument established a differential background counting rate of 4.2 O.7 x 10-5 counts/sec cm keV over the energy range of 40 to 80 keV. This measurement was within 50% of the predicted value. The measured rate is approx 5 times lower than previously achieved in shielded NaI/CsI or Ge systems operating in the same energy range. The prediction was based on a Monte Carlo simulation of the detector assembly in the radiation environment at float altitude.

Vallerga, J.↗

ROSAT all-sky survey observations of X-ray variability in cool giant stars

We have identified 24 active late-type giant stars, including 11 RS CVn systems, with soft X-ray count rates high enough to allow the detection of statistically significant variability on a Roentgen Satellite (ROSAT) orbital timescale (96 minutes) as observed by the Position Sensitive Proportional Counter (PSPC) during the all-sky survey. Our sensitivity typically lies in the range of 10% - 25%, depending on the source count rate. Comparison is made to the daily, nonflare solar soft X-ray variability as observed by the Solrad satellites during solar minimum in 1969 and solar maximum in 1975. Seven of the 24 stars show significant variability; in two of these cases (HR 3922 and HR 8448) major flares were observed in which the peak count rate is enhanced by at least a factor of 3 above quiescent. While HR 3922 (G5 III) is not (yet) classified as an RS CVn star, its flare is more energetic (3 x 10(exp 31) ergs/s) than previously observed RS CVn flares. The apparently single giant HR 8167 (G8 III) also shows two flares. While one might expect to find an anticorrelation between saturated coronae and variability, we find no evidence of this: the two stars in our sample with the highest ratio of f(sub x)/f(sub v) both show variability. We also point out that Capella (G6 III + F9 III) is one of the stars manifesting variability.

Haisch, Bernhard↗

Ge(Li) data reduction using small computers

The advantages and limitations of using a small computer to analyze Ge(Li) radiation spectra are studied. The computer has to: (1) find the spectrum peaks, (2) determine the count rate in the photopeaks, and (3) relate the count rate to known gamma transitions to find the amount of each radionuclide present. Results show that tasks one and two may be done by the computer but task three must be done by an experimenter or a larger computer.

Mcdermott, W. E.↗

Observations of the soft X-ray diffuse background at 0.1 keV

The results of a sounding rocket flight that observed the very soft X-ray diffuse background in a section of the northern Galactic hemisphere are presented. The ratio of the measured Be band count rates to the Wisconsin sky survey B band count rates is nearly constant over a 120 deg arc on the sky, strongly suggesting a common emission mechanism for both Be and B band X-rays. The mean free path is about seven times smaller for the Be band than for the B band. The present results imply that the neutral hydrogen column density between the emitting material and the earth varies by less than 2 x 10 to the 18th H I/sq cm over the observed region. It is concluded that such variations are unlikely unless the total intervening column density is less than a few times this value.

Bloch, J. J.↗

Results of the First Continuous Meteor Head Echo Survey at Polar Latitudes

We present the first quasi continuous meteor head echo measurements obtained during a period of over two years using the Middle Atmosphere ALOMAR Radar System (MAARSY). The measurements yield information on the altitude, trajectory, vector velocity, radar cross section, deceleration and dynamical mass of every single event. The large statistical amount of nearly one million meteor head detections provide an excellent overview of the elevation, altitude, velocity and daily count rate distributions during different times of the year at polar latitudes. Only 40 percent of the meteors were detected within the full width half maximum of the specific sporadic meteor sources. Our observation of the sporadic meteors are compared to the observations with other radar systems and a meteor input function (MIF). The best way to compare different radar systems is by comparing the radar cross section (RCS), which is the main detection criterion for each system. In this study we aim to compare our observations with a MIF, which provides information only about the meteoroid mass. Thus, we are using a statistical approach for the elevation and velocity dependent visibility and a specific mass selection. The predicted absolute count rates from the MIF are in a good agreement with the observation when it is assumed that the radar system is only sensitive to meteoroids with masses higher than one microgram. The analysis of the dynamic masses seems to be consistent with this assumption since the count rate of events with smaller masses are low and decrease even more by using events with relatively small errors.

Interplanetary dust↗

Super active regions and production of major solar flares

The success of imaging detectors with small fields of veiw such as HXIS or P/OF (Pinhole/Occulter Facility) depends heavily on pointing to the right place at the right time. During the solar maximum years many active regions coexist on the solar disk. Therefore, in order to point the imaging detector to the right place, it is important to know which active region is most likely to produce major flares. This knowledge is also important for flare prediction. As a first step toward this goal active regions have been identified which produced major flares observed by HXRBS (Hard X-Ray Burst Spectrometer) on SMM during February 1980 through December 1983. For this study the HXRBS Event List, an updated flare list compiled by the HXRBS group, and the Comprehensive Reports of the Solar Geophysical Data were used. During this period, HXRBS detected hard X-rays from approx 7000 solar flares, out of which only 441 flares produced X-rays with peak count rates exceeding 1000 counts/s. Flares with such high peak count rates are major flares. During the same time period about 2100 active regions passed across the solar disk, out of which only 153 were observed to produce major flares. (Some active regions are known to persist for several solar rotations, but at each passage new active region numbers are assigned and the estimate is based on active region numbers.) Out of these 153 active regions, 25 were observed to produce 5 or more major flares. Considering their high productivity of major flares, we may call these active regions super active regions. These 25 super active regions produced 209 major flares, accounting for 51% of all the major flares with identified active regions.

Bai, T.↗

Central Stars of Planetary Nebulae in the LMC

In FUSE cycle 2's program B001 we studied Central Stars of Planetary Nebulae (CSPN) in the Large Magellanic Could. All FUSE observations have been successfully completed and have been reduced, analyzed and published. The analysis and the results are summarized below. The FUSE data were reduced using the latest available version of the FUSE calibration pipeline (CALFUSE v2.2.2). The flux of these LMC post-AGB objects is at the threshold of FUSE's sensitivity, and thus special care in the background subtraction was needed during the reduction. Because of their faintness, the targets required many orbit-long exposures, each of which typically had low (target) count-rates. Each calibrated extracted sequence was checked for unacceptable count-rate variations (a sign of detector drift), misplaced extraction windows, and other anomalies. All the good calibrated exposures were combined using FUSE pipeline routines. The default FUSE pipeline attempts to model the background measured off-target and subtracts it from the target spectrum. We found that, for these faint objects, the background appeared to be over-estimated by this method, particularly at shorter wavelengths (i.e., < 1000 A). We therefore tried two other reductions. In the first method, subtraction of the measured background is turned off and and the background is taken to be the model scattered-light scaled by the exposure time. In the second one, the first few steps of the pipeline were run on the individual exposures (correcting for effects unique to each exposure such as Doppler shift, grating motions, etc). Then the photon lists from the individual exposures were combined, and the remaining steps of the pipeline run on the combined file. Thus, more total counts for both the target and background allowed for a better extraction.

Bianchi, Luciana↗

HEAO 1 observations of high-energy X-rays from 3C273

The first detection of high energy (13 to 120 keV) X rays from the quasar 3C273, made by the HEAO 1 satellite, is reported. Observations were made with the 13 to 180 keV slat collimated detectors of the high energy X-ray and low energy gamma-ray (A4) experiment during December 1977-January 1978 and June-July 1978. Results are consistent with the previously observed X-ray flux variability on a scale of months. Photon count rates are presented for each of five energy bands and count rate and photon spectra for the June through July 1978 observations are derived. A comparison of the data obtained with that at lower X-ray energies and higher gamma-ray energies indicates that there is an overall spectral steepening from low to high energies and a possible break near 20 keV, which may be due to the gamma rays originating from a different region than that of the X rays.

Primini, F. A.↗

Prolonged triboluminescence in clays and other minerals

Samples of various clays and minerals were ground or fractured and monitored with a liquid scintillation spectrometer in order to obtain triboluminescent decay curves. Kaolinite samples displayed several million counts/min after grinding, with a surface area emission estimated at tens of billions of photons/sq cm of surface. The photon production rates varied with the origin of the sample, and kaolinite continually yielded higher production rates than bentonite. The addition of water to the samples slightly increased the count rate of emitted light, while the addition of the fluorescent molecule substance tryptofan significantly enhanced the count rate. Freezing smears of kaolinite and montmorillonite in liquid nitrogen and in a salt ice mixture also induced triboluminescence in the montmorillonite. A possible connection between powdery triboluminescent materials formed in mining industries and respiratory disorders among miners is suggested.

Lahav, N.↗

High Resolution Soft X-Ray Spectroscopy and the Quest for the Hot (5-10 MK) Plasma in Solar Active Regions

We discuss the diagnostics available to study the 5–10 MK plasma in the solar corona, which is key to understanding the heating in the cores of solar active regions. We present several simulated spectra, and show that excellent diagnostics are available in the soft X-rays, around 100 A, as six ionisation stages of Fe can simultaneously be observed, and electron densities derived, within a narrow spectral region. As this spectral range is almost unexplored, we present an analysis of available and simulated spectra, to compare the hot emission with the cooler component. We adopt recently designed multilayers to present estimates of count rates in the hot lines, with a baseline spectrometer design. Excellent count rates are found, opening up the exciting opportunity to obtain high-resolution spectroscopy of hot plasma.

Giulio Del Zanna↗

Ultrasoft x ray bursts: A clue to the origin of gamma ray bursts?

A search was conducted for short timescale (less than or approx. 10 s) faint X ray bursts in the complete 201,000,000 photon Einstein Observatory imaging proportional counter (IPC) data base. Some 73,000,000 events were extracted which were distributed among 11,230 observing intervals with an average observing time of approx. 1400 seconds. To exclude all sources, only those spatial pixels were searched with a count rate less than 6 x 10(exp -4) counts/sec sq arcmin. The mean count rate was much less. All files with less than 400 secs of observing time were excluded. The data was then binned into overlapping cells 4'.3 by 4'.3 by 10 secs in volume, and all the space-time cells were searched to locate cells with more than 5 counts in a 10 sec interval; i.e., a minimum flux enhancement of 50 over the mean rate for that point in space. Some 52 such events were found. An annulus was inspected around the event to see if it coincided with a general rise in the counter's event rate. Ten events did coincide with counter phenomena; these were associated with sunrise, sunset, or the approach of the South Atlantic Anomaly and were excluded. The remaining 42 events were then examined in an attempt to associate them with instrumental or environmental artifacts. The event occurrence times are uniformly distributed over the course of the mission and show no correlation with local solar time; their positions are randomly distributed in geographic, Galactic, and celestial coordinates. Their summed radial distribution is consistent with the point response function of the IPC for a soft source, indicating that the events are focused by the Observatory's mirror system. The integrated spectrum is, indeed, quite soft and is very similar to that of the cataclysmic variable star U Gem in outburst. Most of the events have risetimes of less than or approx. 1 sec and decay times ranging from 1 to 20 sec. Their positions are not associated with any class of catalogued objects. Several possible origins are discussed for the events; if they are associated with gamma ray bursters, they provide interesting constraints on the space density and repetition rate of the underlying source population.

Helfand, D. J.↗

Dead-time effects in pulse-counting Digicon detectors

The Hubble Space Telescope's High Resolution Spectrograph employs two pulse-counting Digicon detectors to record UV spectra. At higher measured count rates, the intervals between photon arrivals become comparable to the response time of the electronics, so that not every pulse will be counted; this 'paired pulse' effect causes departures from linearity and must be corrected for during raw data reduction. Attention is given to two analytic equations that quantify the dead-time losses. The less attenuated spectra are noted to be severely distorted by these losses; a comparison with the undistorted low count rate data allows a detailed analysis to be made of the pulse-counting characteristics over five decades of input event rates. The present equations and calibration methods should be applicable to all kinds of multichannel pulse-counting detectors.

Ebbets, Dennis C.↗

Application of a dedicated micro-processor for automatic data acquisition of load strain and acoustic-emission data

This paper describes an automatic system for acquisition, logging and analysis of stress, strain and acoustic emission data. The complete system is a combination of several standard items of equipment and a newly developed intelligent data logger which has the capability to send data directly to a large scale computer for reduction and plotting. The data logging and all interfacing with peripheral equipment are accomplished using digital electronics. The heart of the system is a four-bit microprocessor and digital cassette tape unit. The system, which is controlled by instructions from a cathode ray tube terminal, has the capability to transmit data from the cassette unit to a large computer via a time sharing option. Typical results are presented for acoustic emission count rate and total count curves superimposed on stress-strain diagrams for boron/epoxy advanced composites.

Wilson, G. H.↗

Radioactivities of Long Duration Exposure Facility (LDEF) materials: Baggage and bonanzas

Radioactivities in materials onboard the returned Long Duration Exposure Facility (LDEF) satellite were studied by a variety of techniques. Among the most powerful is low background Ge semiconductor detector gamma ray spectrometry. The observed radioactivities are of two origins: those radionuclides produced by nuclear reactions with the radiation field in orbit and radionuclides present initially as contaminants in materials used for construction of the spacecraft and experimental assemblies. In the first category are experiment related monitor foils and tomato seeds, and such spacecraft materials as Al, stainless steel, and Ti. In the second category are Al, Be, Ti, Va, and some special glasses. Consider that measured peak-area count rates from both categories range from a high value of about 1 count per minute down to less than 0.001 count per minute. Successful measurement of count rates toward the low end of this range can be achieved only through low background techniques, such as used to obtain the results presented here.

Smith, Alan R.↗

Contemporaneous IUE, EUVE, and High-Energy Observations of 3C 273

We present the results of our 1994 January and 1995 January observations of the quasar 3C 273 obtained with the International Ultraviolet Explorer (IUE) and the Extreme-Ultraviolet Explorer (EUVE). These observations were part of a large multiwavelength campaign to observe 3C 273 from radio through gamma-rays. Our 1995 January photometric observations with the EUVE Lexan/B Deep Survey (DS) instrument indicate strong evidence for variability, at a 99% confidence level, during the 12 day observing period. We have utilized ROSAT PSPC soft X-ray power-law models to correlate with EUVE count rates. Besides variations in the normalization level between both observations, our EUV count rates are consistent with a simple power-law model with spectral index alpha approx. 1.77 (F(sub upsilon) proportional to upsilon(sup -alpha) that can be extrapolated from the soft X-rays to the EUV range. The active galactic nucleus 3C 273 is an important blazar to study because in our picture it reveals the presence of both disk and relativistic beam spectral contributions.

Ramos, E.↗

Using Beta Cen to Probe the Photosphere-wind Connection in B Stars

In this project we began by identifying the large number of emission lines visible in the XMM-Newton RGS spectra of Beta Cen. A comprehensive analysis of the temperature structure of the hot gas was carried out by simultaneously fitting the data from all the instruments on the spacecraft. This resulted in a measured temperature range of 0.1-0.6 keV. In more detailed analysis, three characteristic plasma temperatures were found: 0.1, 0.2, and 0.6 keV. The research carried out at UW-Eau Claire primarily focused on two aspects of the data: the analysis of the forbidden line to intercombination line ratio for He-like ions and the time variability of the overall X-ray flux as detected in the direct X-ray images of the star. The analysis of the lines from He-like ions indicate that the Ne IX lines are formed no farther than about 4 stellar radii from the star's photosphere, while the N VI lines are formed within 11 stellar radii of the photosphere. X-ray flux variability would be particularly interesting for this star because it is a known Beta Cep-type variable as seen in optical light: similar variation in the X-ray region would forge an interesting link between the two wavebands. Initial analysis of the X-ray flux was complicated by spikes in the count rates early in the observation. Detailed analysis of the spectral characteristics these count rate anomalies indicated that these flares were probably not intrinsic to the star, rather they were contaminations of the data due to the passage of the satellite through soft proton clouds in the Earth's magnetosphere. An analysis of the light curve of the uncontaminated portions of the light curve did not reveal any variation on the known optical period of variation for this star, and a general search for periodic variability also did not find any significant periods of variation.

Miller, Nathan A.↗

Operation of a microchannel plate counting system in a mass spectrometer

A multiplier detector system has been developed as part of a mass spectrometer in an ion counting mode. During its operation ions striking a microchannel plate release pulses of electrons which are accelerated to a phosphor layer. The resulting flash of light is carried by a fiber-optic bundle to a photodiode array. The detector simultaneously counts ions throughout a mass spectrum covering more than 30 amu. It extends the mass spectrometer's operation toward low count rates for trace gas analysis. Each mass peak can be independently measured at count rates between 0.1 and 1000 counts/s. Higher rates on a few peaks do not blind the entire detector. The detector's capabilities have been demonstrated by measuring Kr and Xe isotopes in air at natural abundances. The mass spectrometer, detector, and readout electronics are sufficiently compact to permit use in a balloon-borne experiment.

Murphy, D. M.↗

A Gamma-Ray Burst Trigger Toolkit

The detection rate of a gamma-ray burst detector can be increased by using a count rate trigger with many accumulation times DELTAt and energy bands DELTAE Because a burst's peak flux varies when averaged over different DELTAt and DELTAE the nominal sensitivity (the numerical value of the peak flux) of a trigger system is less important than how much fainter a burst could be at the detection threshold as DELTAt and DELTAE are changed. The relative sensitivity of different triggers can be quantified by referencing the detection threshold back to the peak flux for a fiducial value of DELTAt and DELTA E. This mapping between peak flux values for different sets of DELTAt and DELTAE varies from burst to burst. Quantitative estimates of the burst detection rate for a given detector and trigger system can be based on the observed rate at a measured peak flux value in this fiducial trigger. Predictions of a proposed trigger's burst detection rate depend on the assumed burst population, and these predictions can be wildly in error for triggers that differ significantly from previous missions. I base the fiducial rate on the BATSE observations: 550 bursts per sky above a peak flux of 0.3 ph per square centimeter per second averaged over DELTAt=1.024 sec and DELTAE=50-300 keV. Using a sample of 100 burst lightcurves I find that triggering on any value of DELTAt that is a multiple of 0.064 sec decreases the average threshold peak flux on the 1.024 sec timescale by a factor of 0.6. Extending DELTAE to lower energies includes the large flux of the X-ray background, increasing the background count rate. Consequently a low energy DELTAE is advantageous only for very soft bursts. Whether a large fraction of the population of bright bursts is soft is disputed; the new population of X-ray Flashes is soft but relatively faint.

Band, David L.↗