Search NASA⌕ Search

SEARCH · Search NASA

Results for “Capacity Loss”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Capacity decline of ambient temperature secondary Li-TiS2 cells

The main objective of the study described was to identify the causes responsible for the capacity losses observed during cycling of secondary Li-TiS2 cells. Experimental Li-TiS2 cells were fabricated and tested for their cycle life performance. The open circuit voltage of the cells was monitored during the rest period between the charging and discharging. The polarization at the Li and TiS2 electrodes was also monitored during cycling. Cycled cells were disassembled and the cathodes were analyzed by various analytical techniques. The results of the study indicate that the observed capacity loss is almost entirely due to the increased polarization of the TiS2 electrode with cycling. The electrolyte was found to degrade during cycling and the degradation products were found to deposit at the TiS2 electrode, which probably lead to the higher polarization.

Subbarao, S.↗
DOE OSTI2022

Quantification of Dead Lithium on Graphite Anode under Fast Charging Conditions

A series of computational and experimental studies were conducted to understand the onset of lithium plating and subsequent quantification of dead lithium on graphite electrodes in the design of fast charging batteries. The experiments include titration and relaxation studies for detecting initiation of lithium metal plating for various SOC and C-rates, which are compared against the thermodynamically consistent phase field computational results. The collaborative study on "model graphite electrode" with 2.18 mAh cm-2 nominal capacity at 25 degrees C demonstrates: (1) the macroscopic voltage response during relaxation studies indicate the reintercalation of plated lithium into the graphite anode; (2) for SOC below 60% and low C-Rates, there is no dead lithium; (3) for SOC between 60% to 80%, and C-Rates in the range of 4C-6C show dead lithium both in experiments and simulations; (4) at 100% SOC and 4C-6C rates, large amounts of dead lithium are observed. The study presented here allows us to evaluate the effects of the physical properties of the electrochemical system on plating and stripping kinetics and the amount of dead lithium on graphite electrodes, which determines the cell capacity loss under fast charge.

batteries↗
DOE OSTI2022

Analytical and Numerical Analysis of Lithium Plating Onset in Single and Bilayer Graphite Electrodes during Fast Charging

Lithium plating is commonly observed in anodes charged at fast rates, and can lead to capacity loss and battery safety issues. The increased risk of plating has been attributed to transport limitations, and architectured electrodes may reduce plating risk. However, while theoretical studies have shown that reaction non-uniformity arises due to interplay of transport limitations, anode open circuit voltage behavior and reaction kinetics, its effect on lithium plating has not been studied. We use analytic and numerical simulations to predict onset of plating in graphite anode half-cells at high C-rates and demonstrate how anodes with layered porosities can delay plating. Simplified analytical models identify trends for plating onset and predictions are calibrated against numerical models. A calibrated numerical model of graphite demonstrates qualitative agreement with analytical model predictions. This reaction inhomogeneity mechanism occurs in the absence of lithium ion depletion, indicating that these mechanisms may contribute to capacity loss independently or simultaneously. A bilayer model of graphite exhibits delayed plating onset, and an optimization procedure is presented. This theoretical work presents quantitative and mechanistic insight on how reaction inhomogenity affects lithium metal plating onset and can be used as a guide to engineer anodes resistant to lithium plating.

Mijailovic, Aleksandar S.↗
DOE OSTI2023

Dissolution of the Solid Electrolyte Interphase and Its Effects on Lithium Metal Anode Cyclability

At >95% Coulombic efficiencies, most of the capacity loss for Li metal anodes (LMAs) is through the formation and growth of the solid electrolyte interphase (SEI). However, the mechanism through which this happens remains unclear. One property of the SEI that directly affects its formation and growth is the SEI’s solubility in the electrolyte. Here, in this work, we systematically quantify and compare the solubility of SEIs derived from ether-based electrolytes optimized for LMAs using in-operando electrochemical quartz crystal microbalance (EQCM). A correlation among solubility, passivity, and cyclability established in this work reveals that SEI dissolution is a major contributor to the differences in passivity and electrochemical performance among battery electrolytes. Together with our EQCM, X-ray photoelectron spectroscopy (XPS), and nuclear magnetic resonance (NMR) spectroscopy results, we show that solubility depends on not only the SEI’s composition but also the properties of the electrolyte. This provides a crucial piece of information that could help minimize capacity loss due to SEI formation and growth during battery cycling and aging.

25 ENERGY STORAGE↗
DOE OSTI2022

Difluorophosphoric Acid Generation and Crossover Reactions in LiNixCoyMnzO 2 Cathodes Operating at High Voltage

Cycling lithiated metal oxides to high potential (>4.5 V vs Li) is of significant interest for the next generation of lithium ion batteries as this significantly increases the capacity and energy of cells. However, cells cycled to high potential suffer from rapid capacity fade due to a combination of thickening of the anode solid electrolyte interphase (SEI) and impedance growth on the cathode. While transition metal catalysed degradation of the anode SEI has been widely proposed as a primary source of capacity loss, a related acid induced degradation of the anode SEI is proposed. A systematic investigation of LiNi 0.5 Co 0.2 Mn 0.3 O 2 , and LiNi 0.8 Co 0.1 Mn 0.1 O 2 cathodes cycled to 4.2 and 4.6 V has been conducted and the oxidative generation of the strong acid difluorophosphoric acid (F 2 PO 2 H) has been quantified by solution Nuclear Magnetic Resonance (NMR) spectroscopy. Ex-situ surface analysis of the electrodes with X-ray Photo Electron spectroscopy (XPS) suggests that the generation of F 2 PO 2 H correlates with a thickening of the anode SEI and an increase in the fluorophosphate content of the SEI. Changes to the LiNi 0.8 Co 0.1 Mn 0.1 O 2 surface for cells cycled to 4.6 V are also consistent with the generation of acidic species. There is good correlation between the concentration F 2 PO 2 H, anode SEI degradation and the capacity loss of the cells.

25 ENERGY STORAGE↗
DOE OSTI2020

Redox Behaviors in Li-Excess Cation-Disordered Mn-Nb-O-F Rocksalt Cathode

Lithium-excess cation-disordered rocksalt oxide (DRX) is a new choice of high energy Li-ion cathode materials. DRX cathode can deliver an exceptionally high capacity of >250 mAh/g, implying the participation of cationic transition metal and anionic oxygen redox in the electrochemistry. Understanding the explicit roles of both redox reactions in the newly developed cathode is of critical importance to further development of these materials. Herein, we synthesize a representative Mn-redox-based fluorinated DRX material, Li1.2Mn0.625Nb0.175O1.95F0.05 (LMNOF). Using a comprehensive suite of electroanalytical methods, we probe the cationic and anionic redox processes and their evolution upon cycling exclusively from the electrochemical point of view. This work sheds light on understanding of cationic and anionic redox and their roles in the capacity loss for high-capacity fluorinated DRX cathode, meanwhile, showcases an explicit approach to study the electrochemistry of novel electrode materials using such non-disruptive electroanalytical methods.

Li-ion battery, high-capacity cathode, Li-excess m↗
NASA NTRS2012

Fundamental Investigation of Si Anode in Li-Ion Cells

Silicon is a promising and attractive anode material to replace graphite for high capacity lithium ion cells since its theoretical capacity is approximately 10 times of graphite and it is an abundant element on earth. However, there are challenges associated with using silicon as Li-ion anode due to the significant first cycle irreversible capacity loss and subsequent rapid capacity fade during cycling. In this paper, cyclic voltammetry and electrochemical impedance spectroscopy are used to build a fundamental understanding of silicon anodes. The results show that it is difficult to form the SEI film on the surface of Si anode during the first cycle, the lithium ion insertion and de-insertion kinetics for Si are sluggish, and the cell internal resistance changes with the state of lithiation after electrochemical cycling. These results are compared with those for extensively studied graphite anodes. The understanding gained from this study will help to design better Si anodes.

Wu, James J.↗
NASA NTRS2012

Fundamental Investigation of Silicon Anode in Lithium-Ion Cells

Silicon is a promising and attractive anode material to replace graphite for high capacity lithium ion cells since its theoretical capacity is ~10 times of graphite and it is an abundant element on Earth. However, there are challenges associated with using silicon as Li-ion anode due to the significant first cycle irreversible capacity loss and subsequent rapid capacity fade during cycling. Understanding solid electrolyte interphase (SEI) formation along with the lithium ion insertion/de-insertion kinetics in silicon anodes will provide greater insight into overcoming these issues, thereby lead to better cycle performance. In this paper, cyclic voltammetry and electrochemical impedance spectroscopy are used to build a fundamental understanding of silicon anodes. The results show that it is difficult to form the SEI film on the surface of a Si anode during the first cycle; the lithium ion insertion and de-insertion kinetics for Si are sluggish, and the cell internal resistance changes with the state of lithiation after electrochemical cycling. These results are compared with those for extensively studied graphite anodes. The understanding gained from this study will help to design better Si anodes, and the combination of cyclic voltammetry with impedance spectroscopy provides a useful tool to evaluate the effectiveness of the design modifications on the Si anode performance.

Wu, James J.↗
DOE OSTI2021

Stabilizing Anionic Redox Chemistry in a Mn-Based Layered Oxide Cathode Constructed by Li-Deficient Pristine State

Li-rich cathode materials are of significant interest for coupling anionic redox with cationic redox chemistry to achieve high-energy-density batteries. However, lattice oxygen loss and derived structure distortion would induce serious capacity loss and voltage decay, further hindering its practical application. Herein, a novel Li-rich cathode material, O3-type Li 0.6 [Li 0.2 Mn 0.8 ]O 2 , is developed with the pristine state displaying both a Li excess in the transition metal layer and a deficiency in the alkali metal layer. Benefiting from stable structure evolution and Li migration processes, not only can high reversible capacity (≈329 mAh g -1 ) be harvested but also irreversible/reversible anionic/cationic redox reactions are comprehensively assigned via the combination of in/ex situ spectroscopies. Furthermore, irreversible lattice oxygen loss and structure distortion are effectively restrained, resulting in long-term cycle stability (capacity drop of 0.045% per cycle, 500 cycles). Altogether, tuning the Li state in the alkali metal layer presents a promising way for modification of high-capacity Li-rich cathode candidates.

anionic redox reactions↗
DOE OSTI2021

Al Substitution for Mn during Co-Precipitation Boosts the Electrochemical Performance of LiNi 0.8 Mn 0.1 Co 0.1 O 2

We report nickel-rich layered oxides, such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC 811), are considered as one of the most promising candidates for the next-generation cathode because of their high energy densities and relatively low cost. However, the poor first Coulombic efficiency of NMC 811 leads to around a 15% capacity loss in the first cycle at a cut-off voltage of 4.4 V. Moreover, the structure degradation during cycling results in capacity fading and safety concerns, due to potential oxygen loss after charging. Here, with aluminum substitution for manganese through a developed continuous co-precipitation approach, the electrochemical performance of NMC 811 cathodes has been greatly enhanced. Among different Al% substituted samples, LiNi 0.8 Mn 0.06 Co 0.1 Al 0.04 O 2 cathodes reduced by 50% the first capacity loss of pristine NMC 811(18.0 vs 35.9 mAh g -1 ) and improved the capacity retention from 81.4 to 96.4% after 60 cycles at 0.5C in the voltage range of 2.8–4.4 V.

25 ENERGY STORAGE↗
DOE OSTI2024

Detection of a Cobalt-Containing Interphase at the Li 6 PS 5 Cl-NMC111 Interface by In Situ μ XANES and EIS

Sulfide electrolyte all-solid-state lithium batteries (ASLBs) with uncoated Li-Ni x Mn y Co 1–x–y O 2 (NMC) cathodes suffer from a large capacity loss during initial cycling and an increase in cell impedance. Decomposition reactions are known to occur at the Li 6 PS 5 Cl-NMC111 interface due to incompatibility between the two materials. If a stabilizing coating is applied to the NMC, it delivers full capacity during initial charge. However, the loss in capacity during discharge still occurs. The interface was studied by μ XANES and through EIS analysis. A chemically-formed interphase was detected by μ XANES, evident from reduction of Co at an uncoated NMC particle surface. This interphase was produced by decomposition at rest. To study the effect of the interphase on electrochemically active surface area, piecewise in situ EIS was performed and the data was modeled using a transmission line model (TLM). The charge transfer resistance R CT was used to estimate the volume specific active surface area (a act ). The median value for a act was 296 cm –1 , a factor of 7.5 lower than the theoretical value of 2216 cm –1 . This provided evidence of a lower electrochemically active surface area in the ASLB.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evaluation of Cathode Materials with Lithium-Metal Anodes: Baseline Performance and Protocol Standardization of Coin Cells

The collaborative evaluation of electrode materials across multiple research entities requires standardized electrochemical testing protocols to produce reliable, one-to-one comparisons between different systems of interest. Similar to the work done by Long et al. on protocol standardization for coin-cell testing with graphite anodes [J. Electrochem. Soc., 163, A2999, (2016)], here we introduce two standardized testing protocols designed to quickly evaluate important electrochemical properties of cathode materials using lithium-metal anodes. The two protocols measure kinetic and thermodynamic capacity losses, rate- and voltage-dependent cycling capacities, instabilities at high voltage and high cycling rate, and overpotentials at various states of charge. We then apply these protocols to four commercially available cathode materials to establish benchmark performance metrics that can be used to screen and evaluate new cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2021

Design Considerations for Fast Charging Lithium Ion Cells for NMC/MCMB Electrode Pairs

Lithium ion cells that can be quickly charged are of critical importance for the continued and accelerated penetration of electric vehicles (EV) into the consumer market. Considering this, the U.S. Department of Energy (DOE) has set a cell recharge time goal of 10–15 min. The following study provides an investigation into the effect of cell design, specifically negative to positive matching ratio (1.2:1 vs. 1.7:1) on fast charging performance. By using specific charging procedures based on negative electrode performance, as opposed to the industrial standard constant current constant voltage procedures, we show that the cells with a higher N:P ratio can be charged to ~16% higher capacity in the ten-minute time frame. Cells with a higher N:P ratio also show similar cycle life performance to those with a conventional N:P ratio, despite the fact that these cells experience a much higher irreversible capacity loss, leading to a lower reversible specific capacity.

25 ENERGY STORAGE↗
DOE OSTI2026

Revealing key structures for reversible sulfur redox in amorphous polymeric sulfur

Amorphous polymeric sulfur cathodes, such as sulfurized polyacrylonitrile (SPAN), enable high-energy lithium-sulfur batteries without cobalt or nickel, leveraging abundant sulfur. However, the limited in situ understanding of their synthesis and electrochemistry has impeded targeted optimization. Here, in this study, we integrate operando high-energy total scattering with sulfur K-edge X-ray absorption spectroscopy to monitor SPAN's formation and cycling in real time. Our results show that S-C bond formation halts further fusion of cyclized polyacrylonitrile, fostering π-π stacking and a transition from long-chain to short-chain sulfur-critical for reversible sulfur redox. These features synergistically minimize polysulfide dissolution and charge-transfer resistance, enabling optimized SPAN to achieve high capacity retention over 1,000 cycles. Operando X-ray absorption spectroscopy reveals that residual protons drive thiol-thione tautomerism, with lithium replacement during the first discharge causing ~20% irreversible capacity loss. To enhance performance, minimizing -NH groups and expanding pyridine networks are key. These findings transform SPAN optimization from empirical tuning to mechanism‑guided engineering and point the way towards sulfur loadings and energy densities competitive with state‑of‑the‑art Li‑ion cathodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Boosting the sodium storage behaviors of carbon materials in ether-based electrolyte through the artificial manipulation of microstructure

The porous carbon blacks rationally designed by a facile yet efficient NH 3 thermal etching route have been investigated as anode materials in an ether-based electrolyte for sodium-ion batteries. The as-synthesized CBN35 carbon black with a 35% weight loss after NH3 thermal etching exhibited a large specific charge capacity of 352 mAh g -1 at 50 mA g -1 and a superior rate capability of 101 mAh g -1 at 16000 mA g -1 , due to its highest microporosity, an appropriate surface area, a desirable microstructure, and a promising hybrid intercalation mechanism. Impressively, even cycled at 1600 mA g -1 over 3200 cycles, an outstanding reversible capacity of 103 mAh g -1 with a negligible 0.0162% capacity loss per cycle can still be achieved. Based on the multimodal characterizations including the structural probes of phase evolution for carbon materials, the electrochemical techniques, and the surface-sensitive XAS measurements, the exceptional electrochemical properties should stem from several merits of modified carbon black system. While the particular microporous structure provides relatively more accessible sodium storage sites, a novel hybrid intercalation mechanism in ether-based electrolyte would incorporate the sodium ion insertion into the disordered structure with the solvated sodium ion species co-intercalation into the graphitic phase. In addition to the diffusion-controlled redox reactions, the noticeable surface-induced pseudocapacitive reactions also significantly contribute to the charge storage upon sodiation and guarantee the rapid migrations of sodium ions/solvated compounds. In conclusion, this system further features a controlled emergence of a robust but thin solid electrolyte interphase layer, which could suppress the side reactions of active electrode with reactive electrolyte, maintain the fragile porous structure upon cycling, and facilitate the migrations of sodium ions and solvated sodium ion compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1985

The failure mechanism of a nickel electrode in a nickel-hydrogen cell

Studies on a number of types of nickel electrodes after cycle failure in a Ni/H2 cell showed that the failure is due to the loss of high rate discharge capability rather than an absolute capacity loss. The failure mechanism is speculated to be a combination of migration of the active material away from the current collecting nickel sinter, increased porosity of the active material caused by cycling, and an electrical isolation process of the active material during discharge.

Lim, H. S.↗
DOE OSTI2026

Admissible Powertrain Alternatives for Heavy-Duty Fleets: A Case Study on Resiliency and Efficiency

Heavy-duty vehicles dominate global freight movement and primarily rely on fossil-derived diesel fuel. However, fluctuations in crude oil prices and evolving emissions regulations have prompted interest in alternative powertrains to enhance fleet energy resiliency. This study paired real-world operational data from a large commercial fleet with high-fidelity vehicle models to evaluate the potential for replacing diesel internal combustion engine (ICE) trucks with alternative powertrain architectures. The baseline vehicle for this analysis is a diesel-powered ICE truck. Alternatives include ICE trucks fueled by bio- and renewable diesel, compressed natural gas (CNG) or hydrogen (H 2 ), as well as plug-in hybrid (PHEV), fuel cell electric (FCEV), and battery electric vehicles (BEV). While most alternative powertrains resulted in some payload capacity loss, the overall fleetwide impact was negligible due to underutilized payload capacity for the specific fleet considered in this study. For sleeper cab trucks, CNG-powered trucks achieved the highest replacement potential, covering 85% of the fleet. In contrast, H 2 and BEV architectures could replace fewer than 10% and 1% of trucks, respectively. Day cab trucks, with shorter daily routes, showed higher replacement potential: 98% for CNG, 78% for H 2 , and 34% for BEVs. However, achieving full fleet replacement would still require significant operational changes such as route reassignment and enroute refueling, along with considerable improvements to onboard energy storage capacity. Additionally, the higher total cost of ownership (TCO) for alternative powertrains remains a key challenge. This study also evaluated lifecycle impacts across various fuel sources, both fossil and bio-derived. Bio-derived synthetic diesel fuels emerged as a practical option for diesel displacement without disrupting operations. Conversely, H 2 and electrified powertrains provide limited lifecycle impacts under the current energy scenario. This analysis highlights the complexity of replacing diesel ICE trucks with admissible alternatives while balancing fleet resiliency, operational demands, and emissions goals. These results reflect a US-based fleet’s duty cycles, payloads, GVWR allowances, and an assumption of depot-only refueling/recharging. Applicability to other fleets and regions may differ based on differing routing practices or technical features such as battery swapping.

BEV↗