Search NASA⌕ Search

SEARCH · Search NASA

Results for “Capacity degradation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Degradation of a two-layer thermal barrier coating under thermal cycling

A two-layer plasma-sprayed thermal barrier coating on a directionally solidified nickel-base eutectic alloy substrate was characterized prior to and after thermal cycling to 1095 C in an accelerated furnace test. The coating was comprised of an inner layer of Ni-16.4Cr-5.1Al-0.15Y (wt%) bond coat and an outer layer of ZrO2-7.9Y2O3 (wt%) thermal barrier. Characterization of the bond coat revealed that substantial amounts of yttrium and aluminum were oxidized during plasma-spraying in air. The oxidation of these elements reduced the protective capacity of the bond coat so that, on thermal exposure, severe degradation of the bond coat resulted and large amounts of nickel oxide formed. This nickel oxide was demonstrated to grow outward into the thermal barrier, which appears to have increased the stresses in the thermal barrier and contributed to its failure near the thermal barrier-bond coat interface.

Maier, R. D.↗
NASA NTRS2017

Preliminary Investigation of Impact of Technological Impairment on Trajectory-Based Operations

The Next Generation Air Transportation System (NextGen) incorporates collaborative air traffic management and Trajectory-Based Operations (TBO) in order to significantly increase the capacity, efficiency, and predictability of operations in the National Airspace System (NAS), without decreasing safety. This is enabled by airspace users and service providers sharing knowledge about operations that allows prediction of the complete 4D flight trajectory with as little uncertainty as possible. Additionally, new software and hardware technology is critical to reaching NextGen goals, especially with regard to TBO. What if the technologies that are critical for TBO were to be impaired or fail completely? Should there be a malfunction of a piece of the technology, it must be ensured that the whole system does not break down completely or suffer severe impairment. Instead, operations need to be maintained proportionally to the problem and safety needs to be ensured (graceful degradation). This paper proposes a systematic framework to investigate the vulnerability of TBO to technology disruption, and determine the impact of technological impairment on TBO. Two representative technologies are chosen for detailed investigation and the impact of their impairment on the degradation of TBO is illustrated using a weather-related scenario. XXXX There are several possible directions of future work. We believe it is desirable to develop methods to quantitatively assess the impact of technological disruption on TBO and to have the simulation tools to validate the impact. The availability of prognostics and health management methods could be leveraged to predict technological failure/disruption, thus predicting how TBO will be a ected, and possibly pro-actively mitigating the impact. It is important to develop large-scale scenarios where the e ect of technological impairment is prominent, and identify methods to quantitatively assess the extent of TBO degradation. An important goal of such an investigation is the development of failure-resistant resilient trajectory-based oper- ations. Resilience14, 15 is the property of a system to \bounce back" and resume at least a signi cant portion of its functionalities after degradation due to technological impairment(s). A systems resilience includes properties such as \bu ering capacity" (quantifying disruptions the system can absorb or adapt to without a fundamental breakdown in performance or in the systems structure), \ exibility" (ability to restructure itself in response to external changes or pressures), "margin" (how closely the system is currently operating rela- tive to one or another kind of performance boundary), \tolerance" (whether the system gracefully degrades as stress/pressure increase, or collapses quickly when pressure exceeds adaptive capacity), etc. Future work needs to focus on quantifying and improving the resilience of TBO, and identifying resilient design solutions for aviation.

TBO↗
NASA NTRS1980

Material problems in solar sail development

The paper considers the solar sail principle as an effective means of space propulsion. The heliogyro configuration is discussed including the hub structures, the flap-hinge brace assembly, and the blade. The material requirements of the sail film made of metallized polymers, the tendons produced from a polymer-graphite fiber composite, and battens constructed of graphite/epoxy tubings are considered, noting that not all of these materials were readily available. It was concluded that the primary material problems are the environmental degradation of polymer films, the meteoroid hazard, and the production capacity for large polymer film quantities.

Steurer, W. H.↗
NASA NTRS1975

Advanced computer technology - An aspect of the Terminal Configured Vehicle program

NASA is conducting a Terminal Configured Vehicle program to provide improvements in the air transportation system such as increased system capacity and productivity, increased all-weather reliability, and reduced noise. A typical jet transport has been equipped with highly flexible digital display and automatic control equipment to study operational techniques for conventional takeoff and landing aircraft. The present airborne computer capability of this aircraft employs a multiple computer simple redundancy concept. The next step is to proceed from this concept to a reconfigurable computer system which can degrade gracefully in the event of a failure, adjust critical computations to remaining capacity, and reorder itself, in the case of transients, to the highest order of redundancy and reliability.

Berkstresser, B. K.↗
NASA NTRS1978

Fabrication and testing of silver-hydrogen cells

Silver electrodes containing various additives were fabricated and tested in single electrode cells in order to improve the electrochemical utilization of sintered silver cathodes in Ag-H2 aerospace batteries. A standard stack arrangement was used which featured a NASA-developed organic-inorganic separator. All cells were cycled in a regime designed to remove 75% of the cells nominal capacity based on 3.3 gms/AHr Ag utilization. In cases where performance degradation was observed, the main feature mode appeared to be corrosion of either the expanded silver current collector or the connection between the silver electrode and the electrode tab. Promising silver electrodes from single electrode studies were used in the construction of 35 AHr Ag-H2 cells. Two such cells were constructed and installed in heavy walled pressure vessels for testing. Based on the data obtained from all cells tested during the program, four lightweight 35 AHr cells were fabricated. During acceptance testing these cells yielded an average gravimetric energy density of 30 WHr/1b.

Debicarri, D. J.↗
NASA NTRS1986

Study of ice accretion on icing wind tunnel components

In a closed loop icing wind tunnel the icing cloud is simulated by introducing tiny water droplets through an array of nozzles upstream of the test section. This cloud will form ice on all tunnel components (e.g., turning vanes, inlet guide vanes, fan blades, and the heat exchanger) as the cloud flows around the tunnel. These components must have the capacity to handle their icing loads without causing significant tunnel performance degradation during the course of an evening's run. To aid in the design of these components for the proposed Altitude Wind Tunnel (AWT) at NASA Lewis Research Center the existing Icing Research Tunnel (IRT) is used to measure icing characteristics of the IRT's components. The results from the IRT are scaled to the AWT to account for the AWT's larger components and higher velocities. The results show that from 90 to 45 percent of the total spray cloud froze out on the heat exchanger. Furthermore, the first set of turning vanes downstream of the test section, the FOD screen and the fan blades show significant ice formation. The scaling shows that the same results would occur in the AWT.

Newton, J. E.↗
NASA NTRS1986

Study of ice accretion on icing wind tunnel components

In a closed loop icing wind tunnel the icing cloud is simulated by introducing tiny water droplets through an array of nozzles upstream of the test section. This cloud will form ice on all tunnel components (e.g., turning vanes, inlet guide vanes, fan blades, and the heat exchanger) as the cloud flows around the tunnel. These components must have the capacity to handle their icing loads without causing significant tunnel performance degradation during the course of an evening's run. To aid in the design of these components for the proposed Altitude Wind Tunnel (AWT) at NASA Lewis Research Center the existing Icing Research Tunnel (IRT) is used to measure icing characteristics of the IRT's components. The results from the IRT are scaled to the AWT to account for the AWT's larger components and higher velocities. The results show that from 90 to 45 percent of the total spray cloud froze out on the heat exchanger. Furthermore, the first set of turning vanes downstream of the test section, the FOD screen and the fan blades show significant ice formation. The scaling shows that the same results would occur in the AWT.

Newton, J. E.↗
NASA NTRS1977

Effects of periodic discharges

Periodic capacity checks are assessed as well as the effects of periodic discharges on the cycle life and the performance of cells during the cycle life. Topics discussed include the effect of the amount of electrolyte on cell capacity at 35 C; battery design for spacecraft; electrolyte starvation theory; battery separator degradation; negative electrode stability; voltage regulation; operating temperatures; and integration of reconditioning systems using microprocessors.

Ford, F. E.↗
NASA NTRS1991

Evaluation of sodium-nickel chloride cells for space applications

The status of the European Space Agency (ESA) program on sodium nickel chloride batteries is outlined. Additionally, the results of initial tests of two prototype space cells are reported. After 2800 cycles typical of a low-earth orbit (LEO) application without failure, the recharge ratio remained at unity, the round trip energy efficiency remained high (87 percent), and the increase in internal cell resistance was modest. Initial tear-down analysis data show no degradation whatsoever of the beta-alumina electrolyte tubes. The low-rate capacity did, however drop by some 40 percent, which needs further investigation, but overall results are encouraging for future use of this couple in geosynchronous (GEO) and LEO spacecraft.

Hendel, B.↗
NASA NTRS1983

An application of gap regenerator/expander precooled by two stage G-M refrigerator

The degradation of regenerator effectiveness below 10K is due to the imbalance of the heat capacity of the regenerator material and helium gas as a working fluid. One of the attractive methods to increase this efficiency could be realized by a gap regenerator system regarding helium gas property. This paper describes an experiment using pressurized helium gas as a regenerator material. A two stage G-M cycle refrigerator has been used for precooling the gap regenerator system. With this method, minimum temperature below 5K has been obtained when the precooling temperature maintained at 10K.

Matsubara, Y.↗
NASA NTRS1987

Stability of IRA-45 solid amine resin as a function of carbon dioxide absorption and steam desorption cycling

The removal of CO2 from the NASA Space Station's cabin atmosphere, which may be undertaken by a solid-amine water (steam)-desorbed system, is presently evaluated with a view to long-term amine resin stability and adsorption/desorption cycling by means of an automated laboratory flow-testing facility. While the CO2-adsorption capacity of the IRA-45 amine resin used gradually decreased over time, the rate of degradation significantly decreased after the first 10 cycles. Attention is given to the presence (and possible need for removal) of trimethylamine in the process air downstream of the resin bed.

Wood, Peter C.↗
NASA NTRS2002

Hubble Space Telescope On-orbit NiH2 Battery Performance

This paper summarizes the Hubble Space Telescope (HST) nickel-hydrogen (NiH2) battery performance from launch to the present time. Over the life of HST vehicle configuration, charge system degradation and failures together with thermal design limitations have had a significant effect on the capacity of the HST batteries. Changes made to the charge system configuration in order to protect against power system failures and to maintain battery thermal stability resulted in undercharging of the batteries. This undercharging resulted in decreased usable battery capacity as well as battery cell voltage/capacity divergence. This cell divergence was made evident during on-orbit battery capacity measurements by a relatively shallow slope of the discharge curve following the discharge knee. Early efforts to improve the battery performance have been successful. On-orbit capacity measurement data indicates increases in the usable battery capacity of all six batteries as well as improvements in the battery cell voltage/capacity divergence. Additional measures have been implemented to improve battery performance, however, failures within the HST Power Control Unit (PCU) have prevented verification of battery status. As this PCU fault prevents the execution of on-orbit capacity testing, the HST Project has based the battery capacity on trends, which utilizes previous on-orbit battery capacity test data, for science mission and servicing mission planning. The Servicing Mission 38 (SM-3B) in March 2002 replaced the faulty PCU. Following the servicing mission, on-orbit capacity test resumed. A summary of battery performance is reviewed since launch in this paper.

Rao, Gopalakrishna M.↗
NASA NTRSDate not supplied

Capacity Building Engagement for Estimating Forest Stand Height Utilizing the SAR Handbook

Utilizing Synthetic Aperture Radar (SAR) which provides information such as vegetation structure and moisture content, independently of weather conditions is a powerful tool that can be employed to more effectively monitor deforestation and estimate biomass which is of paramount concern, especially in South and Southeast Asia which contain nearly 15% of all tropical forests. SERVIR, a NASA-USAID initiative, works in partnership with regional hubs around the world building capacity through promoting the use of Earth observations and geospatial technologies. The SERVIR Global network and the Silva Carbon program collaboratively developed the SAR Handbook: Comprehensive Methodologies for Forest Monitoring and Biomass Estimation which set out to reduce the barriers associated with leveraging SAR and increase the capacity of researchers and practitioners globally to use SAR for monitoring. In particular, utilizing SAR to estimate Forest Stand Height (FSH) is crucial for greenhouse gas emissions reporting and estimating carbon storage. Programs such as Reducing Emissions from Deforestation and Forest Degradation (REDD) rely on parameters such as these for their monitoring efforts. This talk will showcase the collaborative efforts, emergent geospatial technology leveraged, and capacity building approaches utilized by our team to conduct a South and Southeast Asia focused in-person training event located at SERVIR-Mekong, a SERVIR hub lead by the Asian Disaster Preparedness Center (ADPC) in Bangkok.

AGU↗
NASA NTRS1981

Glass as encapsulation for low-cost photovoltaic solar arrays

In photovoltaic systems, the encapsulant material that protects the solar cells should be highly transparent and very durable. Glass satisfies these two criteria and is considered a primary candidate for low-cost, photovoltaic encapsulation systems. In this paper, various aspects of glass encapsulation are treated that are important for the designer of photovoltaic systems. Candidate glasses and available information defining the state of the art of glass encapsulation materials and processes for automated, high volume production of terrestrial photovoltaic devices and related applications are presented. The desired characteristics of glass encapsulation are (1) low degradation rates, (2) high transmittance, (3) high reliability, (4) low-cost, and (5) high annual production capacity. The glass design areas treated herein include the types of glass, sources, prices, physical properties and glass modifications, such as antireflection coatings.

Bouquet, F. L.↗
NASA NTRS1993

Nondestructive characterization of the elastic constants of fiber reinforced composites

Composite structural components may be subjected to a variety of defects resulting in a sharp reduction in their load carrying capacity or even catastrophic failure. Thus, it is extremely important to have the means to monitor the degradation suffered by critical components of a structure for safe operation during its service life. A nondestructive method based on ultrasonics has recently been developed for the quantitative evaluation of composite structural components during service. The experimental part of the technique uses a two-transducer, pitch-catch type arrangement to generate a variety of elastic waves within the specimen immersed in water. The recorded reflection data are then analyzed by means of a theoretical model to back out the relevant properties. In this paper the method is applied to determine the stiffness constants of unidirectional graphite/epoxy materials. The measurements are shown to be efficient and sufficiently accurate so that it can be used for early detection of material degradation in composite structural elements during service.

Mal, Ajit K.↗
NASA NTRS1973

Non-gassing nickel-cadmium battery electrodes and cells: Testing of 25 Ah cells

The testing of 30 practical size, experimental 25 ampere hour cells constructed as part of an earlier negative limited cell development program is discussed. The test results showed that the negative limited cell is a possible means of developing a long-lived secondary cell. The cells were tested for 500 cycles using an accelerated regime approximating a 90-minute orbit period. Three groups of ten cells were tested at 0,25, and 40 C. The cycle data showed that the negative limited cells had higher degradation rates at the higher operating temperatures. At the conclusion of 500 cycles, the three groups had average capacities of 16.83, 12.74, and 5.71 ampere hours for testing at 0, 25, 40 C, respectively. The conditioning capacities of these cells was in the 25 ampere hours range. The internal cell pressures of the three groups was also temperature dependent and was, in general, in the 2 psig range during the course of the test program. No periodic variation of the internal pressure with the state-of-charge was observed except with some cells tested at 40 C.

Luksha, E.↗
NASA NTRS1984

Positive Electrode Fabrication for Bi-polar Ni-h2 Cells

Bi-Polar nickel hydrogen design studies indicated a potential improvement in energy density and specific energy if positive electrodes could be manufactured in configurations of twice or more of the present normal thickness. Such electrodes would have to achieve similar active material loading, utilization, and cycle life to conventional 0.8mm I.P.U. nickel hydrogen electrodes. A capability for producing 1.0mm dry sinter and 1.5mm slurry sinter structures on production processes and equipment was demonstrated. The EPI/USAF electrochemical impregnation process proved capable of loading thick electrodes to 1.60 g/cubic centimeters void or higher. Sample electrodes incurred 2000 high rate stress cycles without significant structural or performance degradation. Formation regimes developed for thin plaque are not optimal for thick plaque and further investigation into electrode capacity build-up would seem warranted. Thick electrode technology development is continuing under other programs and shows promise of fulfilling the projected energy density and specific energy improvements.

Edgar, T. A.↗
NASA NTRS1988

LEO life tests on a 75 Ah bipolar nickel-hydrogen battery

The design, building, and testing of an actively cooled 10-cell 75-Ah bipolar nickel/hydrogen battery are discussed. During the last 1000 cycles, the battery has shown some evidence of elecrical performance degradation. In particular, EOC and EOD voltages have increased and decreased by several millivolts, respectively, and deep discharge capacities to a 1.0 V/cell average cutoff voltage have decreased.

Lenhart, S.↗