Search NASA⌕ Search

SEARCH · Search NASA

Results for “Casting Optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Development of Repair Techniques for Cast Iron Engine Blocks by Additive Manufacturing

ORNL partnered with Cummins Inc to demonstrate the feasibility of using additive manufacturing techniques to deposit large volume of new material on cast iron in the context of remanufacturing. Remanufacturing at Cummins Inc is carried out to repair any field damage and, in some cases, provide additional value by adding new features. Large volume deposition on difficult to weld materials is a challenging problem due to involved metallurgy. Phase-1 of this work evaluated the feasibility of using laser directed energy deposition technique to deposit new material layer by layer on cast iron engine blocks. During phase-1 deposits were made using Inconel-718, Nickel, Nr-Cr-B braze filler. Leveraging the knowledge gained during Phase-1, Phase-2 focused on developing a low- cost crack resistant ferrous alloy to repair cast iron via volume deposition techniques without preheating. Three different alloy chemistries were identified, and trials were performed on cast iron substrates to identify the optimal chemistry that provided adequate resistance to cracking in both, the deposits as well as the cast iron substrate.

42 ENGINEERING↗

Optimization of Hot Deformation Parameters and Constitutive Analysis for As-Cast Mg-5Li-3Zn-0.3Y Alloy Using Processing Maps

Hot deformation behavior of as-cast Mg-5Li-3Zn-0.3Y (wt.%) alloy has been studied by establishing processing maps covering the range of 200-450 °C in temperature and 0.001-10 s{sup −1} in strain rate. The map corresponding to the strain of 0.7 reveals that a domain of dynamic recrystallization occurred at 340-400 °C/0.01-0.158 s{sup −1} with its peak efficiency of approximately 31%. Analysis of the flow behaviors and microstructural observations indicated that dynamic recrystallization occurred in the domain, in which fine microstructure can be achieved. The above conditions represent the optimum processing parameters, and the flow instability regimes are also recognized from the maps. The average deformation in the deformed range was 136.414 kJ/mol which is close to that for lattice self-diffusion in magnesium and far smaller than that for as-cast Mg-5.75Zn-0.73Y-0.36Zr (wt.%) alloy. It is believed that a lower activation energy for Mg-5Li-3Zn-0.3Y alloy can partly result from both the weak particle pinning effects and adding Li into the Mg-Zn-Y-Zr alloy. Results of extrusion experiments conducted at 350 °C show that the alloy can be easily extruded with good mechanical properties of the yield strength of 132 MPa, the fracture strength of 215 MPa and the elongation of 20.9%, and the grains can be well refined.

36 MATERIALS SCIENCE↗

Optimization of excess Bi doping to enhance ferroic orders of spin casted BiFeO{sub 3} thin film

Multiferroic Bismuth Ferrite (BiFeO{sub 3}) thin films with varying excess bismuth (Bi) concentration were grown by chemical solution deposition technique. Room temperature multiferroic properties (ferromagnetism, ferroelectricity, and piezoelectricity) of the deposited BiFeO{sub 3} thin films have been studied. High resolution X-ray diffraction and Raman spectroscopy studies reveal that the dominant phases formed in the prepared samples change continuously from a mixture of BiFeO{sub 3} and Fe{sub 2}O{sub 3} to pure BiFeO{sub 3} phase and, subsequently, to a mixture of BiFeO{sub 3} and Bi{sub 2}O{sub 3} with increase in the concentration of excess Bi from 0% to 15%. BiFeO{sub 3} thin films having low content (0% and 2%) of excess Bi showed the traces of ferromagnetic phase (γ-Fe{sub 2}O{sub 3}). Deterioration in ferroic properties of BiFeO{sub 3} thin films is also observed when prepared with higher content (15%) of excess Bi. Single-phased BiFeO{sub 3} thin film prepared with 5% excess Bi concentration exhibited the soft ferromagnetic hysteresis loops and ferroelectric characteristics with remnant polarization 4.2 μC/cm{sup 2} and saturation magnetization 11.66 emu/g. The switching of fine spontaneous domains with applied dc bias has been observed using piezoresponse force microscopy in BiFeO{sub 3} thin films having 5% excess Bi. The results are important to identify optimum excess Bi concentration needed for the formation of single phase BiFeO{sub 3} thin films exhibiting the improved multiferroic properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Method and apparatus for in-situ drying investigation and optimization of slurry drying methodology

A method of drying casted slurries that includes calculating drying conditions from an experimental model for a cast slurry and forming a cast film. An infrared heating probe is positioned on one side of the casted slurry and a thermal probe is positioned on an opposing side of the casted slurry. The infrared heating probe may control the temperature of the casted slurry during drying. The casted slurry may be observed with an optical microscope, while applying the drying conditions from the experimental model. Observing the casted slurry includes detecting the incidence of micro-structural changes in the casted slurry during drying to determine if the drying conditions from the experimental model are optimal.

36 MATERIALS SCIENCE↗

Optimization of edge bead removal (EBR) process to enhance defect reduction in optical lithography

Defect reduction remains a critical objective in the integrated circuit manufacturing process, particularly within the highly re-entrant lithography modules where minimizing defects is crucial. Defects at the wafer edge can contaminate lithography modules and downstream processing equipment, leading to redistribution onto the wafer surface and adversely affecting overall device yield. A persistent challenge in the resist coating process is the formation of resist edge beads, driven by the strong Van der Waals attraction of excess photoresist (PR) to itself and the underlying substrate. The edge bead removal (EBR) process is a standard cleaning step designed to eliminate these edge beads and prevent potential contamination. Here, in this study, we identify the sources of EBR induced defects and additional EBR process encroachment toward edge patterning during the EBR cleaning process. This study provides a comprehensive study aimed at optimizing the EBR cleaning process to effectively eliminate EBR-induced defects, thereby enhancing overall device yield. Specifically, we identify three primary defects induced by the EBR cleaning process: rainbow-type, finger-shaped, and teardrop-type defects. Our experimental study reveals that in addition to EBR rinse time, PR cast time is crucial parameters contributing to the formation of these defects. By properly optimizing the PR cast time and EBR rinse time, we were able to remove nearly 100 % of dense clusters of defects that were easily visible even at low magnification optical microscopy throughout the wafer edge. We observed that shorter PR casting times shows edge defects caused by inefficient EBR process because of insufficient time for PR to fully settle causing superfluous PR to continue flowing toward wafer edge during EBR clearing step, leading to partial removal of PR at the wafer edge and the formation of rainbow defects. Proper optimization of both PR casting time and EBR chemistries dispense time is essential to resolve these defects, ensuring efficient EBR cleaning process and improved overall device yield.

42 ENGINEERING↗

Synthesis of nanostructured/macroscopic low-density copper foams based on metal-coated polymer core–shell particles [Templated synthesis of nanowalled low-density copper foams]

A robust, millimeter-sized low-density Cu foam with ~90% (v/v) porosity, ~30 nm thick walls, and ~1 μm diameter spherical pores is prepared by the slip-casting of metal-coated polymer core–shell particles followed by a thermal removal of the polymer. In this paper, we report our key findings that enable the development of the low-density Cu foams. First, we need to synthesize polystyrene (PS) particles coated with a very thin Cu layer (in the range of tens of nanometers). A simple reduction in the amount of Cu deposited onto the PS was not sufficient to form such a low-density Cu foams due to issues related to foam collapse and densification upon the subsequent polymer removal step. Precise control over the morphology of the Cu coating on the particles is essential for the synthesis of a lower density of foams. Second, improving the dispersion of PS–Cu particles in a suspension used for the casting as well as careful optimization of a baking condition minimize the formation of irregular large voids, leading to Cu foams with a more uniform packing and a better connectivity of neighboring Cu hollow shells. Finally, we analyzed mechanical properties of the Cu foams with a depth-sensing indentation test. The uniform Cu foams show a significant improvement in mechanical properties (~1.5× modulus and ~3× hardness) compared to those of uncontrolled foam samples with a similar foam density but irregular large voids. As a result, higher surface areas and a good electric conductivity of the Cu foams present a great potential to future applications.

36 MATERIALS SCIENCE↗

Advanced Anion Exchange Membranes with Tunable Water Transport for PGM-Free AEMFCs

This project advanced the synthesis, characterization, and testing of anion exchange membranes for use in fuel cells. Our goal was to improve the water transport in anion exchange membrane fuel cells to improve their performance and durability. Through the work in this project we: 1) developed new composite anion exchange membranes through polymer synthesis and membrane casting into mechanical supports; 2) optimized electrode architecture and cell conditions to achieve; 3) demonstrated an integrated approach to achieving over 1 W/cm 2 in an operating device. While we did not achieve 1000 hours of continuous operation, we demonstrated multiple runs of more than 300 hours of device performance at steady-state.

08 HYDROGEN↗

Jump-Start U.S. Manufacturing of High-Performance Permanent Magnets

Gas atomized feedstock powders for Nd-Fe-B based magnets are more robust and cost effective than the strip-cast sheet currently used as feedstock for milling by the magnet industry. However, gas atomized powder’s crystallinity and grain boundary phases are less ideal than the strip cast flake. We proposed to optimize the atomization process as well as the powder chemistry to address this issue and to eliminate heavy rare earth elements from these magnet alloys. Our goal is to help GKN-Hoeganaes, a US metal powder company, who used to make Nd-Fe-B magnets, to bring back US manufacturing of these high energy density permanent magnets.

36 MATERIALS SCIENCE↗

Coreset Clustering on Small Quantum Computers

Many quantum algorithms for machine learning require access to classical data in superposition. However, for many natural data sets and algorithms, the overhead required to load the data set in superposition can erase any potential quantum speedup over classical algorithms. Recent work by Harrow introduces a new paradigm in hybrid quantum-classical computing to address this issue, relying on coresets to minimize the data loading overhead of quantum algorithms. We investigated using this paradigm to perform k-means clustering on near-term quantum computers, by casting it as a QAOA optimization instance over a small coreset. We used numerical simulations to compare the performance of this approach to classical k-means clustering. We were able to find data sets with which coresets work well relative to random sampling and where QAOA could potentially outperform standard k-means on a coreset. However, finding data sets where both coresets and QAOA work well—which is necessary for a quantum advantage over k-means on the entire data set—appears to be challenging.

42 ENGINEERING↗

A Bayesian experimental design approach to structural health monitoring

Optimal system design for SHM involves two primarily challenges. The first is the derivation of a proper performance function for a given system design. The second is the development of an efficient optimization algorithm for choosing a design that maximizes, or nearly maximizes the performance function. In this paper we will outline how an SHM practitioner can construct the proper performance function by casting the entire design problem into a framework of Bayesian experimental design. The approach demonstrates how the design problem necessarily ties together all steps of the SHM process.

42 ENGINEERING↗

An error-in-constitutive equations strategy for topology optimization for frequency-domain dynamics

This paper presents a topology optimization formulation for frequency-domain dynamics to reduce solution dependence upon initial guess and considered loading conditions. Due to resonance phenomena in undamped steady-state dynamics, objectives measuring dynamic response possess many local minima that may represent poor solutions to a design problem, an issue exacerbated for design with respect to multiple frequencies. In this work, we propose an extension of the modified error-in-constitutive-equations (MECE) method, used previously in material identification inverse problems, as a new approach for frequency-domain dynamics topology optimization to mitigate these issues. The main idea of the proposed framework is to incorporate an additional penalty-like term in the objective function that measures the discrepancy in the constitutive relations between stresses and strains and between inertial forces and displacements. Then, the design problem is cast within a PDE-constrained optimization formulation in which we seek displacements, stresses, inertial forces, and a density-field solution that minimize our new objective subject to conservation of linear momentum plus some additional constraints. We show that this approach yields superior designs to conventional gradient-based optimization approaches that solely use a functional of displacements as the objective, while strictly enforcing the constitutive equations. The MECE strategy integrates into a density-based topology optimization scheme for void–solid or two-phase material structural design. We highlight the merits of our approach in a variety of scenarios for direct frequency response design, considering multiple frequency load cases and structural objectives.

42 ENGINEERING↗

Deployment of Alumina Forming Austenitic (AFA) Stainless Steel

The purpose of the project was to accelerate the deployment and further the development of a new family of heat-resistant alloys developed at ORNL: alumina-forming austenitic (AFA) stainless steels. Initial laboratory scale evaluation indicated that AFA alloys possess exceptional high-temperature oxidation resistance while retaining creep properties similar to other advanced austenitic stainless steels. The AFA steels therefore represent a low-cost alternative to Ni-base alloys and a high performance alternative to conventional advanced austenitic steels. Deployment of AFA steels into turbine and other energy-related applications can lead to improved efficiencies by achieving higher operating temperatures and/or improved durability and component lifetime at costs comparable to currently used alloys. The development and scale up of optimized AFA alloy compositions in both wrought and cast forms, including generation of a database of thermo-physical, mechanical, welding/joining, and high-temperature corrosion properties was needed to enable consideration and adoption of these new materials in applications ranging from turbines, heat exchangers, and fuel cells to boilers and chemical/petrochemical processing. The project consisted of four primary tasks: commercial demonstrations, property database development, alloy development and optimization and evaluation of as-cast properties.

Alumina Forming Ausenitic Steel↗

The Effect of Membrane Structure Prepared from Carboxymethyl Cellulose and Cellulose Nanofibrils for Cationic Dye Removal

Water-stable and eco-friendly membranes were fabricated from carboxymethyl cellulose (CMC) acting as anionic adsorbent and cellulose nanofibrils (CNFs) as strengthening filler by solvent- and unidirectional freeze-casting processes, both supported with simultaneous citric acid (CA) mediated cross-linking. Spectroscopic, thermogravimetric and potentiometric titration techniques were applied to evaluate the efficacy of the cross-linking as well as to quantify the processing-dependant surface charge. In addition, the CMC/CNF assembling and membrane porosity were identified microscopically as the combinatorial effect of components ratio and the applied fabrication technique. Finally, the membrane’s cationic dyes adsorption capacity and kinetic were evaluated depending on the dyes ionization constants, solution pH, and the contact time using batch equilibrium experiment, and further evaluated for filtration performance at optimal pH. The resulting, freeze-casted membranes demonstrate anisotropic to isotropic and highly (> 90%) porous structures with gradient pore sizes (from few nm up to 200 µm range). This provides relatively high and stable flux rates (150–190 kL/m{sup 2} h MPa) with ~ 100% cationic dye adsorption, fast dynamic (8.536–5.446 kg/g min) and capacity (1828–1398 g/kg), which highlight their potential in dead-end filtration technologies without need for additional separation step. The similar dye adsorption capacity was assessed for denser and nano-porous (< 50 nm) solvent-casted membranes, however, with much lower and time-declining flux rates (100–10 L/m{sup 2} h MPa), demonstrating their potential usage in spiral wound-cross-flow modules. Both types of membranes anyhow showed high dye removal capacity (≥ 90%) even after 4th (solvent-casted) and 50th (freeze-casted) reusing cycle, present a high-value alternative to commercial activated carbons or other bio-nano-absorbents.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Roll-to-Roll SOFC Manufacturing for Low Cost Energy Generation

Oak Ridge National Laboratory (ORNL) and Redox Power Systems, LLC. collaborated on this project to develop an integrated, continuous roll-to-toll (R2R) manufacturing processes to produce solid oxide fuel cells (SOFCs). SOFCs are ceramic-based electrochemical devices that efficiently produce electricity from hydrogen-containing fuels, including natural gas. Standard processes for manufacturing SOFCs include tape casting of the anode and electrolyte, followed by stacking of the layers, and lamination using a uniaxial press or isostatic press. After high temperature firing, the cathode and electrical contact are screen printed and fired once again to complete the cell. This effort aimed to further develop R2R tape fabrication processes for green cell fabrication with the DOE Battery Manufacturing Facility (BMF) at ORNL as next generation improvements to current methods, focusing on R2R calendering and slot die coating for lower cost, high volume approaches for multilayer green cell fabrication. Two paths were investigated in parallel in this project. The first path was to optimize R2R processing using traditional tape cast materials from the Redox production chain on the BMF’s heated calender for compressing and laminating multilayer materials. The second path was to use BMF’s pilot-scale slot-die coater for R2R manufacturing as an alternative to tape casting of some or all of the layers in the green cell. Processes have been developed and and process conditions have been identified. Additionally, basic process economics were estimated for comparison to Redox current manufacturing approaches for the applicable process modules. The SBV program results will enable Redox to advance lower cost R2R manufacturing processes to produce millions of green cells per year on a single production line. As a result of this work, one invention disclosure has been submitted. In addition, one paper is under preparation for submission to a peer-reviewed journal.

30 DIRECT ENERGY CONVERSION↗

A modeling comparison of deep greenhouse gas emissions reduction scenarios by 2030 in California

California aims to reduce greenhouse gas (GHG) emissions to 40% below 1990 levels by 2030. We compare six energy models that have played various roles in informing the state policymakers in setting climate policy goals and targets. These models adopt a range of modeling structures, including stock-turnover back-casting models, a least-cost optimization model, macroeconomic/macro-econometric models, and an electricity dispatch model. Results from these models provide useful insights in terms of the transformations in the energy system required, including efficiency improvements in cars, trucks, and buildings, electrification of end-uses, low- or zero-carbon electricity and fuels, aggressive adoptions of zero-emission vehicles (ZEVs), demand reduction, and large reductions of non-energy GHG emissions. Some of these studies also suggest that the direct economic costs can be fairly modest or even generate net savings, while the indirect macroeconomic benefits are large, as shifts in employment and capital investments could have higher economic returns than conventional energy expenditures. These models, however, often assume perfect markets, perfect competition, and zero transaction costs. They also do not provide specific policy guidance on how these transformative changes can be achieved. Greater emphasis on modeling uncertainty, consumer behaviors, heterogeneity of impacts, and spatial modeling would further enhance policymakers' ability to design more effective and targeted policies. Here, this paper presents an example of how policymakers, energy system modelers and stakeholders interact and work together to develop and evaluate long-term state climate policy targets. Lastly, even though this paper focuses on California, the process of dialogue and interactions, modeling results, and lessons learned can be generally adopted across different regions and scales.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

A subzone reconstruction algorithm for efficient staggered compatible remapping

Staggered-grid Lagrangian hydrodynamics algorithms frequently make use of subzonal discretization of state variables for the purposes of improved numerical accuracy, generality to unstructured meshes, and exact conservation of mass, momentum, and energy. For Arbitrary Lagrangian–Eulerian (ALE) methods using a geometric overlay, it is difficult to remap subzonal variables in an accurate and efficient manner due to the number of subzone–subzone intersections that must be computed. This becomes prohibitive in the case of 3D, unstructured, polyhedral meshes. A new procedure is outlined in this paper to avoid direct subzonal remapping. The new algorithm reconstructs the spatial profile of a subzonal variable using remapped zonal and nodal representations of the data. The reconstruction procedure is cast as an under-constrained optimization problem. Enforcing conservation at each zone and node on the remapped mesh provides the set of equality constraints; the objective function corresponds to a quadratic variation per subzone between the values to be reconstructed and a set of target reference values. Numerical results for various pure-remapping and hydrodynamics tests are provided. Ideas for extending the algorithm to staggered-grid radiation-hydrodynamics are discussed as well as ideas for generalizing the algorithm to include inequality constraints.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Fabrication of U-10 wt.%Zr Metallic Fuel Rodlets for Irradiation Test in BOR-60 Fast Reactor

The fabrication technology for metallic fuel has been developed to produce the driver fuel in a PGSFR in Korea since 2007. In order to evaluate the irradiation integrity and validate the in-reactor of the starting metallic fuel with FMS cladding for the loading of the metallic fuel, U-10 wt.%Zr fuel rodlets were fabricated and evaluated for a verification of the starting driver fuel through an irradiation test in the BOR-60 fast reactor. The injection casting method was applied to U-10 wt.%Zr fuel slugs with a diameter of 5.5 mm. Consequently, fuel slugs per melting batch without casting defects were fabricated through the development of advanced casting technology and evaluation tests. The optimal GTAW welding conditions were also established through a number of experiments. In addition, a qualification test was carried out to prove the weld quality of the end plug welding of the metallic fuel rodlets. The wire wrapping of metallic fuel rodlets was successfully accomplished for the irradiation test. Thus, PGSFR fuel rodlets have been soundly fabricated for the irradiation test in a BOR-60 fast reactor.

Kim, Ki-Hwan↗