Search NASA⌕ Search

SEARCH · Search NASA

Results for “CdTe:I”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Understanding the Role of CdTe in Polycrystalline CdSe x Te 1– x /CdTe-Graded Bilayer Photovoltaic Devices

Grading of bandgap by alloying CdTe with selenium to form a CdSe x Te 1–x /CdTe-graded bilayer device has led to a device efficiency over 19%. A CdSe x Te 1–x absorber would increase the short-circuit current due to its lower bandgap but at the expense of open-circuit voltage. It has been demonstrated that adding a CdTe layer at the back of such a CdSe x Te 1–x film reduces the voltage deficit caused by the lower bandgap of absorber from selenium alloying while maintaining the higher short-circuit current. This leads to a photovoltaic device that draws advantage from both materials with an efficiency greater than either of them. In this report there is a detailed account using device data, ultraviolet photoelectron spectroscopy, electron microscopy, and first-principles density functional theory modeling is provided, which shows that CdTe acts as an electron reflector for CdSe x Te 1–x .

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Thermomechanical Cleave of Polycrystalline CdTe Solar Cells and its Applications: A Review

One of the primary research challenges for cadmium telluride (CdTe) solar cells is addressing its open‐circuit voltage ( V OC ) deficit. While theoretical studies and single crystal work show V OC > 1 V is possible, devices remain stubbornly low at ≈800–900 mV. As absorber opto‐electronic properties (e.g., hole density, carrier lifetime) are improved, device modeling suggests that interfaces become limiting. Because CdTe‐based devices are typically grown in the superstrate configuration, the back interface is relatively accessible for manipulation and study, while the front interface (i.e., the heterojunction region) is buried under microns of material and inaccessible. NREL has developed a novel technique to thermomechanically cleave polycrystalline CdTe device stacks directly at the front interface, enabling characterization and controlled manipulation of this important region. Herein, recent work, primarily from NREL, will be reviewed, including considerations for achieving successful delamination; key scientific discoveries about the front interface that have been enabled by this technique; and practical applications, such as flexible, low‐cost solar with high power‐to‐weight ratio.

14 SOLAR ENERGY↗
DOE OSTI2020

Effects of post-deposition CdCl 2 annealing on electronic properties of CdTe solar cells

The effects of post-deposition CdCl 2 annealing temperature on the electronic properties of CdTe solar cells were investigated. CdTe devices incorporate Mg doped ZnO as a buffer layer and selenization using a CdSe interlayer for reducing the buffer/absorber interface recombination and increasing solar energy absorption respectively. The post-deposition CdCl 2 annealing treatments were done under separate, inert atmospheres of nitrogen and helium across the temperature range 380 to 430 °C. Electrical characterization of devices is carried out including temperature dependent current-voltage characteristics, admittance spectroscopy, and Shockley-Read-Hall recombination analysis. Here, the best improvements in device efficiency are obtained upon annealing at temperature 410 °C. This anneal correlated with reduced back contact barrier in CdTe and reduced grain-boundary barrier height which is beneficial for enhanced charge transport.

14 SOLAR ENERGY↗
DOE OSTI2020

Imaging hole-density inhomogeneity in arsenic-doped CdTe thin films by scanning capacitance microscopy

We report nanometer-scale hole-density imaging in As-doped CdTe films by scanning capacitance microscopy (SCM). The hole-density profiling is validated by contrasting a CdTe cross-section sample made by molecular-beam epitaxy with systematically increased As doping in a staircase pattern over the range of 10 15 -10 18 /cm 3 within a single film. In polycrystalline films, the carrier distribution is significantly nonuniform, with inhomogeneity ranging from several hundred nm to several um and hole density varying by one order of magnitude (low 10^16 to low 10 17 /cm 3 ). This nonuniformity is distributed randomly, independent of the grain structure and grain boundaries (GBs). Kelvin probe force microscopy (KPFM) maps the surface potential and is correlated to cathodoluminescence (CL) and SCM by imaging over identical areas. Higher potential and lower CL intensity are found on GBs but not by SCM contrast; this indicates positive GB charging and recombination, but not GB-specific hole-density changes. The overall KPFM potential image is in rough agreement with the SCM carrier distribution and indicates band-edge potential fluctuations. Nonuniform carrier concentration, potential fluctuations, and defect recombination can all cause voltage and performance loss in As-doped CdTe solar technology.

14 SOLAR ENERGY↗
DOE OSTI2020

Stable magnesium zinc oxide by reactive Co-Sputtering for CdTe-based solar cells

Magnesium zinc oxide (MZO) is a promising front contact material for CdTe solar cells. Due to its higher band gap than traditional CdS, MZO can reduce parasitic absorption to significantly increase short-circuit current density while also providing a benefit of conduction band offset tuning through Mg:Zn ratio optimization. MZO has been successfully implemented into CdTe devices, however its stability has been of concern. The MZO stability issue has been attributed to the presence of oxygen in the CdTe device processing ambient, leading to double-diode behavior (S-kink) in the current density-voltage curves. Here we report on MZO thin films deposited by reactive co-sputtering. The reactively co-sputtered MZO thin films have encouraging stability, show no significant variation in work function of the surface over a period of 6 months, as measured by Kelvin probe. Energy conversion efficiencies of around 16% have been achieved both with and without presence of oxygen in device processing ambients across multiple research facilities. Finally, these efficiencies should be possible to increase further by tuning of the thin film deposition and device processing parameters, especially through optimization of the back contact.

14 SOLAR ENERGY↗
DOE OSTI2023

Water-Assisted Lift-Off Process for Flexible CdTe Solar Cells

In recent years, various lift-off methods have been developed to fabricate lightweight and flexible cadmium telluride (CdTe)-based solar cells. In this work, we report flexible cadmium sulfide (CdS)/CdTe solar cells using a water-assisted lift-off approach. Here we demonstrate that an additional cadmium chloride treatment for the CdS film is critical to improve the grain size of CdS and the post-deposited CdTe film and the electron conductivity of the CdS film. As a result, the quality of the CdS/CdTe front junction is significantly improved with reduced nonradiative recombination. Finally, our lightweight and flexible polycrystalline CdTe solar cells demonstrate a champion power conversion efficiency of 12.6%.

14 SOLAR ENERGY↗
DOE OSTI2020

Stable CdTe Photoanodes with Energetics Matching Those of a Coating Intermediate Band

Here, a TiO 2 coating was grown on a CdTe absorber by atomic layer deposition for stabilization against its photocorrosion during photoelectrochemical water splitting. Under simulated sunlight (AM 1.5G, 100 mW cm –2 ), this multilayer CdS/CdTe/TiO 2 /Ni/NiO x photoanode produced a light-limited photocurrent density of 24.5 ± 0.5 mA cm –2 and a photovoltage of 780 ± 20 mV. This record energy-conversion performance was comparable to those of baseline CdS/CdTe solar cells and was achieved only after the development of proper CdTe surface treatments prior to coating the stabilization layer. The TiO 2 coating, with its in-gap charge-transport intermediate band, facilitates hole transport as light exits the CdTe/TiO 2 interface. With proper interfacial chemistry, the electrochemical potential energy of the coating intermediate band matched that of the CdTe valence band. Moreover, the stabilized CdS/CdTe/TiO 2 /Ni/NiO x photoanodes showed 100 h stability for water oxidation under light-on/light-off cycles. This study provides insightful guidance for designing stabilization contacts for efficient and stable light-driven water oxidation.

14 SOLAR ENERGY↗
DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗
DOE OSTI2021

Distinguishing bulk and surface recombination in CdTe thin films and solar cells using time-resolved terahertz and photoluminescence spectroscopies

Understanding the nature of recombination and its dependence on defects and interfaces is essential for engineering materials and contacts for higher open circuit voltage (V oc ) and power conversion efficiency in photovoltaic (PV) devices. Time-resolved photoluminescence (TRPL) has conventionally been used to evaluate recombination, but carrier redistribution often dominates the response at short times. In this work, we report on the quantification of carrier dynamics and recombination mechanisms by complementary use of both time-resolved terahertz spectroscopy (TRTS) and TRPL combined with numerical modeling of the continuity equations and Poisson’s equation. We have demonstrated this approach using CdTe thin films. A thin film stack with CdTe fabricated by vapor transport deposition and treated with CdCl 2 exhibited a bulk lifetime of 1.7 ± 0.1 ns, negligible CdTe/CdS interface recombination velocity, and back surface recombination velocity of 6.3 ± 1.3 x10 4 cm/s. In contrast, a film stack without CdCl 2 treatment had a bulk lifetime of only 68 ± 12 ps and a higher interface recombination velocity of 4 ± 2 x10 8 cm/s. By determining the locus and mechanisms of performance-limiting recombination, we can accelerate the development of thin-film PVs with higher V oc and efficiency. While the method has been demonstrated here using CdTe, it is also applicable to perovskites, Cu(InGa)Se 2 , Cu2ZnSn(S,Se) 4, and emerging technologies.

14 SOLAR ENERGY↗
DOE OSTI2021

Colossal grain growth in Cd(Se,Te) thin films and their subsequent use in CdTe epitaxy by close-spaced sublimation

Many technologies deposit thin films on inexpensive substrates, resulting in small grains due to classic nucleation and grain growth theory. For example, state-of-the-art solar cells are made by depositing CdSeTe and CdTe layers on inexpensive glass coated with nanocrystalline transparent conducting oxides (TCOs), like SnO 2 . Characteristically, the grain size of these films is on the order of the film thickness, i.e. a few microns. CdTe small-grain films have poor electro-optical properties and require CdCl 2 passivation which fails to fully passivate grain boundaries, causes carrier compensation, and prevents implementing other II–VI alloys and materials to improve performance. Here, we present a method to increase grain size to 1 mm in CdSe x Te 1-x thin films deposited on glass/TCO substrates without CdCl 2 treatment. The colossal grain growth is driven by mechanisms distinct from classic nucleation, grain growth, and Ostwald ripening and only occurs at low selenium content (x ~ 0.1). We also demonstrate how these films can serve as templates for subsequent large-grain epitaxy of other compositions like CdTe, again without exposure to CdCl 2 . The results open new paths for thin film solar cell technology, and thin film devices in general.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hybrid Functional Calculations for Antimony Doping in CdTe

CdTe-based solar cells are leading thin-film photovoltaic technology, with efficiencies over 22%, but still much lower than the theoretical maximum of 29%. Further improvements will rely on increasing the open-circuit voltage Voc, which, in turn, depends on carrier density and lifetime. Using hybrid density functional calculations, we investigate Sb doping of CdTe, focusing on its limitation as shallow acceptor and the formation of compensating AX center. Paying special attention to supercell size and effects of spin-orbit coupling, we predict an ionization energy of 116 meV in the dilute limit, much closer to recent experimental value of 103 meV from temperature-dependent Hall measurements in bulk single crystals, and in contrast to much larger values from previous calculations. We also find that the Sb-related AX centers are not major compensation centers in Sb-doped CdTe.

14 SOLAR ENERGY↗
DOE OSTI2021

Photovoltaics Research and Development: Device Architecture for Next-Generation CdTe PV. Cooperative Research and Development Final Report, CRADA Number CRD-17-00662

Despite remarkable efficiency improvements at the cell and module level, thin-film CdTe PV suffers from a significant voltage deficit compared with the ideal. The proposed solution is to build cells with fully depleted absorbers and with energy barriers front and back to direct electrons and holes in appropriate directions. Combined with minimal interfacial recombination, this approach, which is similar to the successful silicon HIT cells, circumvents the need for higher lifetimes and carrier concentration to achieve higher voltage, Colorado State is particularly well-positioned to the address the depleted absorbed architecture. It has robust single-vacuum closed-spaced-sublimation deposition chamber, currently being enhanced with new sources for CdTe alloys and grading. It has made reasonable-efficiency cells with absorbers as thin as 0.3 um, it has demonstrated electron reflection at the rear of the absorber with a continuous CdMgTe layer, it has replaced CdS with MgZnO, which has several advantages including tunable band offsets, and it has achieved 16.8% efficiency. It also has a mature suite of measurement equipment for cell evaluation and the experience to effectively analyze its results for refinement in cell fabrication. Several healthy collaborations will continue within the CdTe community.

14 SOLAR ENERGY↗
DOE OSTI2022

Improved CdTe PLR Estimates: Self-Shading and Spectral Mismatch

The RdTools year-on-year method of estimating performance loss rate (PLR) employs a simple normalization to remove the confounding effect of irradiance and temperature variation. However, the normalization's assumption that PV production scales linearly with in-plane broadband irradiance is a worse approximation for CdTe and other technologies with larger spectral sensitivities than it is for the more common c-Si technology. Additionally, CdTe systems using single-axis trackers (-20% of installed US utility-scale capacity) are subject to self-shading in the morning and afternoon, introducing another nonlinearity between PV output and broadband irradiance. Ignoring these effects may subject the estimated PLR to increased uncertainty, and perhaps bias, depending on the character of their short- and long-term variability. In this work we show that including self-shading and spectral mismatch models in the normalization for tracking CdTe systems can result not only in tighter PLR confidence intervals but different median PLRs as well. The shading and spectral models are kept simple to maintain consistency with the RdTools ethos of not requiring detailed system metadata or unusual measurements.

CdTe↗
DOE OSTI2025

Nm-scale electrical resistance imaging on CdTe by scanning spreading resistance microscopy

Local resistance imaging can provide information on nm-scale carrier distribution in semiconductor devices. Scanning spreading resistance microscopy (SSRM), an atomic force microscopy-based nm-scale resistance mapping technique, has been developed for carrier delineation in Si microdevices. We report on the development and validation of SSRM on CdTe materials, by testing on molecular beam epitaxy (MBE) grown CdTe films. The probe/CdTe contact resistance was suppressed sufficiently below sample's spreading resistance by pressing the probe into the sample with ∼mN contact force and applying a large sample/probe forward bias voltage (V s ), which was understood by analyzing current-voltage (I-V) involving a serially connected insulating top layer with underlying spreading resistance. The carrier concentration as deduced from the resistance measurement, using a single mobility value, is consistent with Hall measurement with a standard deviation of 14% based on a set of MBE films with carrier concentrations in the range of 10 15 –10 16 /cm 3 . The doping polarity was readily identified by flipping V s polarity, where the resistance with reverse V s is orders of magnitude larger than forward V s . While focusing on the SSRM technique validation, we also show an example on an As-doped Cd(Se,Te) polycrystalline thin film of a high-performance CdTe solar cell, which illustrates the local resistance nonuniformity with up to two orders of magnitude differences, indicating if local mobility is roughly constant, local carrier concentration can have significant nonuniformity.

14 SOLAR ENERGY↗
DOE OSTI2026

Analysis of native oxides grown on single-crystal CdTe and MgCdTe

Over the course of CdTe photovoltaics development, many refinements to the device stack have been made. One area of current interest is the back contact interface, where surface passivation is critical to prevent recombination at the interface. One candidate material for achieving strong passivation is TeO 2 . Using scanning transmission electron microscopy, we investigate native oxide formations on CdTe and Mg x Cd 1−x Te substrates to better understand the oxides' chemical composition and the interface they form with the material they are grown on. We find that substoichiometric TeO x forms as a native oxide on CdTe, and on Mg x Cd 1−x Te, we found a MgO native oxide. Some TeO x appeared atop the MgO layer, though it was not consistently present. As a result, the native oxides had preferential interface terminations, with Cd terminations at the CdTe/TeO x interface and Te terminations at the Mg x Cd 1−x Te/MgO interface.

14 SOLAR ENERGY↗
DOE OSTI2023

Symmetry-driven persistent spin texture for the two-dimensional nonsymmorphic CdTe and ZnTe crystal structures

In this paper, two nonsymmorphic two-dimensional structures of CdTe and ZnTe are modeled, and using state-of-the-art density functional theory with the group theory of solids, their symmetry-enforced electronic properties are studied. The in-plane ferroelectricity coupled with strong spin-orbit coupling induces a unidirectional out-of-plane Rashba spin-orbit field that can host a momentum-independent uniform spin configuration known as persistent spin texture (PST) at the Brillouin zone center. PST in these structures is found to be robust against external perturbations such as strain, structural distortion, and independent of layer thickness. These unprecedented intrinsic spin transport properties hold utmost importance in spintronics, as the experimental stringent condition of equal Rashba and Dresselhaus constants [Phys. Rev. Lett. 90, 146801 (2003)] is eliminated. The calculated persistent spin helix wavelength of <~5 nm paves the way for developing next-generation nanosized nonballistic spin field-effect transistors compared with micrometer-sized GaAs/AlGaAs quantum wells. Further, these materials exhibit finite spin Hall conductivity at the band edges and hence can be used in ferromagnet-free spin Hall transistors. Although CdTe and ZnTe systems have been widely studied for photocatalysis and solar cell applications over the past few decades, their potential application in spintronic devices has not been explored. Mono/few layers of CdTe and ZnTe synthesized from (110) facets of bulk zinc-blende crystals [Nat. Commun. 3, 1057 (2012)] satisfy all symmetry operations of the nonsymmorphic space group and hence can be considered ideal materials to verify our theoretical results experimentally.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Point defects in CdTe and CdSeTe alloy: a first principles investigation with DFT+U

CdTe and its alloy CdSeTe are widely used in optoelectronic devices, such as radiation detectors and solar cells, due to their superior electrical properties. However, the formation of defects and defect complexes in these materials can significantly affect their performance. As a result, understanding the defect formation and recombination processes in CdTe and CdSeTe alloy is of great importance. In recent years, density functional theory (DFT) calculations have emerged as a powerful tool for investigating the properties of defects in semiconductors. In this paper, we use DFT+U calculations to comprehensively study the properties of intrinsic defects as well as extrinsic defects induced by commonly used dopants, such as Cu and group V elements, in CdTe and CdSeTe alloy. This work provides insights into the effects of these defects on the electrical and optical properties of the material.

14 SOLAR ENERGY↗
DOE OSTI2024

Characterizing electron-collecting CdTe for use in a 77 ns burst-rate imager

The Keck-PAD (pixel array detector) was developed at Cornell as a burst-rate imager capable of recording images from successive electron bunches (153 ns period) from the Advanced Photon Source (APS). Both Si and hole-collecting Schottky CdTe have been successfully bonded to this ASIC (application-specific integrated circuit) and used with this frame rate. The facility upgrades at the APS will lower the bunch period to 77 ns, which will require modifications to the Keck-PAD electronics to image properly at this reduced period. In addition, operation at high X-ray energies will require a different sensor material having a shorter charge collection time. For the target energy of 40 keV for this project, simulations have shown that electron-collecting CdTe should allow >90% charge collection within 35 ns. This collection time will be sufficient to sample the signal from one frame and prepare for the next. 750 µm-thick electron-collecting Schottky CdTe has been obtained from Acrorad and bonded to two different charge-integrating ASICs developed at Cornell, the Keck-PAD and the CU-APS-PAD. Carrier mobility has been investigated using the detector response to single X-ray bunches at the Cornell High Energy Synchrotron Source and to a pulsed optical laser. The tests indicate that the collection time will meet the requirements for 77 ns imaging.

36 MATERIALS SCIENCE↗