Search NASA⌕ Search

SEARCH · Search NASA

Results for “CdTe photovoltaics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Photovoltaics Research and Development: Device Architecture for Next-Generation CdTe PV. Cooperative Research and Development Final Report, CRADA Number CRD-17-00662

Despite remarkable efficiency improvements at the cell and module level, thin-film CdTe PV suffers from a significant voltage deficit compared with the ideal. The proposed solution is to build cells with fully depleted absorbers and with energy barriers front and back to direct electrons and holes in appropriate directions. Combined with minimal interfacial recombination, this approach, which is similar to the successful silicon HIT cells, circumvents the need for higher lifetimes and carrier concentration to achieve higher voltage, Colorado State is particularly well-positioned to the address the depleted absorbed architecture. It has robust single-vacuum closed-spaced-sublimation deposition chamber, currently being enhanced with new sources for CdTe alloys and grading. It has made reasonable-efficiency cells with absorbers as thin as 0.3 um, it has demonstrated electron reflection at the rear of the absorber with a continuous CdMgTe layer, it has replaced CdS with MgZnO, which has several advantages including tunable band offsets, and it has achieved 16.8% efficiency. It also has a mature suite of measurement equipment for cell evaluation and the experience to effectively analyze its results for refinement in cell fabrication. Several healthy collaborations will continue within the CdTe community.

14 SOLAR ENERGY↗
DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗
DOE OSTI2020

Cadmium Selective Etching in CdTe Solar Cells Produces Detrimental Narrow-Gap Te in Grain Boundaries

Recent advances in design and processing technology have made possible commercialization of polycrystalline (px)-CdTe as a photovoltaic absorber. Grain boundaries (GBs) are the most prominent structural defects in these devices and undergo significant changes during device fabrication. However, the effects of device fabrication processes on these GBs are not entirely understood. Prevailing models of GBs in thin-film photovoltaics consider individual GBs to have homogeneous properties in their area. Here, using an aberration-corrected scanning transmission electron microscope (STEM)-based low-loss and core-loss electron energy-loss spectroscopy (EELS), we show that back-surface etching of CdTe leads to inhomogeneity within individual grain boundaries. We observe that etching the back surface leads to the conversion of a region of GBs from CdTe to an elemental Te, which has an only 0.33 eV band gap, as deep as 1 μm from the back surface. The presence of elemental Te in GBs this deep into the absorber layer will increase recombination in the absorber layer and limit the extractable open-circuit voltage, thus reducing device efficiency. However, additive methods for back contact formation such as deposition of Te, ZnTe, or other materials preserve the CdTe stoichiometry of the GBs. Thus, especially for the next generations of CdTe-based cells having longer minority carrier diffusion length and/or thinner absorber layers, additive back contacting methods are superior.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomistic modeling of energy band alignment in CdTe(1 0 0) and CdTe(1 1 1) surfaces

An atomic-scale perspective of energy band alignment in CdTe surfaces has not been spatially studied despite the major role surfaces play in forming interfaces within CdTe-based thin film photovoltaic devices. Atomistic modeling based on density functional theory coupled with surface Green’s function is used for calculating energy band alignment of CdTe surfaces. The CdTe(1 0 0) ((1×1) and c(2×2) reconstruction) and CdTe(1 1 1) ((1×1) and (2×2) reconstruction) facets without and with surface relaxation provide insightful band bending characteristics that influence charge carrier transport. Results show that unrelaxed (1×1) CdTe(1 0 0) and CdTe(1 1 1) surfaces bend the valence band downward with surface polarity dictating the surface potential magnitude. The reconstructed CdTe(1 0 0) c(2×2) and CdTe(1 1 1) (2×2) surfaces result in favorable surface electronic features in relation to their unreconstructed variants. In addition, the structurally relaxed CdTe(1 1 1) surfaces develop an internal energy cusp potential that may enhance hole charge transport toward the back of CdTe solar cell devices. In conclusion, energy band alignments calculated within the study lead to a detailed understanding of how CdTe surfaces may affect CdTe-based thin film photovoltaic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The effects of antimony incorporation on the optoelectronic properties of Cd(Se,Te) photovoltaics

One historical limitation of CdTe PV devices has been the open circuit voltage (VOC) deficit (difference between theoretical maximum VOC and measured values). While non-radiative recombination at extended structural defects and interfaces negatively impacts VOC, intentionally adding impurities (dopants) to increase the concentration of free carriers in the photovoltaic (PV) absorber material can increase the VOC. In this contribution we present a detailed analysis of the Sb doped CdTe and the Cd(Se,Te) alloy system via electron beam induced current (EBIC) measurements and the presence as well as spatial distribution of defect levels through cathodoluminescence spectrum imaging (CLSI).

14 SOLAR ENERGY↗
DOE OSTI2026

Collaborative R&D with REEL Solar Inc (REEL) to Understand and Overcome Performance Limitations in CdTe Solar Cells: Cooperative Research and Development (Final Report)

This CRADA will focus on processing, advanced characterization, and testing of photovoltaic materials and devices to understand and improve REEL CdTe solar technology. This will include examining process variations and different buffer, absorber, and contact layers from REEL and NLR to maximize performance. The unique and diverse advanced characterization tools at NLR, such as time-resolved photoluminescence, capacitance-voltage measurements, electron beam scattered diffraction, cathodoluminescence, electron microscopy, TOF-SIMS, and other measurements will be applied to characterize REEL processing to improve understanding and guide experimental directions. Accelerated stability and potential induced degradation tests will be used to analyze metastability, short-and-long term degradation, and improve bankability. A second and major thrust this period will be joint development of Si/CdTe tandem solar cells to overcome industry wide terrestrial solar efficiency limits with the two lowest cost and manufacturable solar materials today. This will include developing novel transparent back contacts that can be incorporated into tandem structures and other novel solar applications, detailed analysis of designs and configurations for CdTe/Si tandem modules, and prototyping REEL CdTe Technology with Si bottom cells in tandem structures.

14 SOLAR ENERGY↗
DOE OSTI2026

Data Associated with "Identifying Suitable Front Contacts for High-Efficiency Cd(Se,Te) Solar Cells on Space-Qualified Cover Glass"

This is data associated with the publication " Identifying Suitable Front Contacts for High-Efficiency Cd(Se,Te) Solar Cells on Space-Qualified Cover Glass " by Aesha P. Patel, Ryan Muzzio, Matthew R. Young, Robert Morrissey, Suresh Chaulagain, B. Edward Sartor, Prabodika N. Kaluarachchi, Christian Velez, Joshua A. Brown, Joel N. Duenow, Stephen Glynn, Michael J. Heben, Zhaoning Song, Nikolas J. Podraza, Adam B. Phillips, Randy J. Ellingson, Matthew O. Reese. All data associated with each figure in the manuscript and supplementary should be available in this dataset. A readme file is also included to provide some guidance. Abstract: Deployment of photovoltaics in space requires devices that combine high-efficiency, low areal mass, and resilience to harsh environments. Historically, high-efficiency multijunction III–V materials have dominated space power systems; however, their high cost and limited manufacturing throughput motivate the exploration of scalable alternatives. While CdTe-based thin-film photovoltaics offer an attractive option, their performance on non-conventional substrates can suffer from front-contact instability under higher-temperature processing. Here, the role of front-contact chemistry in limiting cell performance is investigated using CdTe-based devices fabricated on 150 μm thick Ceria-doped space-qualified 0214 Corning glass. A matrix of four transparent conducting oxides (TCOs: CTO, AZO, ITO, IZO) combined with two n-type emitters (MZO, IGO) reveals chemical stability at the front interface—rather than absorber composition alone—governs recombination losses, voltage deficits, and device reproducibility. Chemically stable front-contact combinations suppress elemental diffusion and interfacial degradation, resulting in significantly improved carrier lifetimes and junction quality. These insights are validated through record-certified Cd(Se,Te) cell efficiencies of 18.4% under AM1.5G and 16.2% under AM0 illumination on ultra-thin glass. Beyond CdTe, this work provides a general framework for the rational selection of TCO/emitter interfaces in superstrate thin-film photovoltaics, including emerging technologies like metal halide perovskites, while enabling high-efficiency, lightweight photovoltaics for space applications.

14 SOLAR ENERGY↗
DOE OSTI2021

Computational design of passivants for CdTe grain boundaries

CdTe is the second most-widely deployed photovoltaic (PV) material due to its high efficiency and low manufacturing costs. Currently, polycrystalline CdTe (poly-CdTe) has a record efficiency of similar to 22%, which is still well below the theoretical limit (similar to 30%). Polycrystalline CdTe films that have incorporated Cl or Se show higher efficiency, possibly due to the segregation of these ions to the grain boundaries (GBs), where they may passivate the dangling bonds. However, the efficiency enhancement mechanisms of passivants in CdTe GBs, and the feasibility of employing alternative passivants, have not been well explored. Here, we present a systematic computational study of CdTe GBs with potential passivants, namely S, P, As, Se, and Sb on Te sites, and Na, Mg, Al, Sc, Cu, and Zn on Cd sites. Density functional theory (DFT) calculations were performed on GB dislocation core structures derived from scanning transmission electron microscopy (STEM) images of a model GB (bicrystal). We computed the segregation thermodynamics, electronic density of states, and charge variations near doped CdTe GBs. We find that segregation of impurities to GBs is thermodynamically favorable. For a Te-terminated core, Se, S, and P on Te sites effectively reduce midgap states. For both Cd-and Te-terminated dislocation cores, Sc and Al reduce midgap states when substituted for Cd atoms. Overall, the greatest improvement was achieved with co-doping, i.e. simultaneously substituting Te with Se and substituting Cd with Cu or Al. The elimination of midgap states is predicted to increase the photovoltaic efficiency of CdTe by reducing the recombination at grain boundaries.

14 SOLAR ENERGY↗
DOE OSTI2021

CdTe‐Based Solar Cells with Variations in Mg Concentration in the MgZnO Emitter

The optimal fraction of Mg incorporation in sputter-deposited Mg X Zn 1−X O (MZO) emitters for thin-film CdTe-based solar cells is evaluated by varying it over a range of x from 0 to 0.35. This range allows a variation in the conduction band offset from −0.1 eV (cliff like) to +0.32 eV (spike like). Here, a maximum efficiency of 18.5% for cells with the bilayer CdSeTe/CdTe absorber occurs at x = 0.15, which corresponds to a spike-like band offset near 0.2 eV, as confirmed by X-ray photoelectron spectroscopy. In addition, good cell performance is seen over a fairly broad range of x extending from 0.1 to 0.25. The MZO optical bandgap increases with the Mg fraction, consistent with an increasing conduction band offset. Temperature-dependent current−voltage measurements and time-resolved photoluminescence show improvement in the emitter/absorber interface with the incorporation of Mg. Capacitance−voltage measurements show that the depletion region extends further into the absorber with more Mg, and X-ray diffraction confirms a change from a hexagonal-dominant crystal structure toward zinc blende at x = 0.35.

14 SOLAR ENERGY↗
DOE OSTI2020

Cost estimates of production scale semitransparent organic photovoltaic modules for building integrated photovoltaics

Building integrated photovoltaics (BIPVs) are attached to commercial and residential structures to enable solar energy harvesting. While conventional Si photovoltaics (PVs) are dominant in the current market, second and third generation thin film solar cells based on amorphous Si, CdTe, CIGS, perovskites or organic photovoltaics (OPVs) are often considered as an alternative for BIPV applications since they may offer reduced costs compared to Si PVs. Indeed, recent advances in performance suggest that lightweight, flexible and visibly transparent OPVs can potentially be integrated into windows or other applications to which Si PVs are less well suited. Here, we estimate the cost of high efficiency, semitransparent OPVs (ST-OPVs) based on solution processing in a roll-to-roll (R2R) manufacturing line. Assuming modules with 10% power conversion efficiency (PCE), a 70% geometric fill factor (GFF), and 95% inverter efficiency, we anticipate a %1.6 per Wp module manufacturing cost that includes the cost of the microinverter to condition the OPV dc output to be compatible with the ac line voltage of the building. The materials and inverter cost comprise ~90% of the total module cost. Hence, with simplified material synthesis and a lower inverter cost, including marginally improved PCE and GFF, we expect the cost can be as low as $0.47 per Wp. Here, while the module costs ~60% of the average (uninstalled) double-pane window, we expect the payback period can be as short as 2 to 6 years, suggesting that OPVs can be an economic and attractive candidate for BIPV applications.

14 SOLAR ENERGY↗
DOE OSTI2021

Optimization of Source Material for in-situ Arsenic Doping via Vapor Transport Deposition of CdTe Films

In-situ doping of CdTe/CdSeTe films with arsenic is performed using pre-doped source material prepared by high pressure Bridgman (HPB) melt growth. Arsenic level in the source material is varied from 1018-1020 cm-3. Correspondingly, dopant incorporation in the films prepared using vapor transport deposition (VTD) varied from 3x1017 cm-3–1x1018cm-3. In this range, dopant activation is found to inversely correlate with the dopant incorporation, suggesting compensation. The results from this study indicate film properties can be adjusted by source material.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2026

Identifying Suitable Front Contacts for High‐Efficiency Cd(Se,Te) Solar Cells on Space‐Qualified Cover Glass

Deployment of photovoltaics in space requires devices that combine high-efficiency, low areal mass, and resilience to harsh environments. Historically, high-efficiency multijunction III–V materials have dominated space power systems; however, their high cost and limited manufacturing throughput motivate the exploration of scalable alternatives. While CdTe-based thin-film photovoltaics offer an attractive option, their performance on non-conventional substrates can suffer from front contact instability under higher-temperature processing. Here, the role of front contact chemistry in limiting cell performance is investigated using CdTe-based devices fabricated on 150 μm thick Ceria-doped space-qualified 0214 Corning glass. A matrix of four transparent conducting oxides (TCOs: CTO, AZO, ITO, IZO) combined with two n-type emitters (MZO, IGO) reveals chemical stability at the front interface—rather than absorber composition alone—governs recombination losses, voltage deficits, and device reproducibility. Chemically stable front contact combinations suppress elemental diffusion and interfacial degradation, resulting in significantly improved carrier lifetimes and junction quality. These insights are validated through record-certified Cd(Se,Te) cell efficiencies of 18.4% under AM1.5G and 16.2% under AM0 illumination on ultra-thin glass. Beyond CdTe, this work provides a general framework for the rational selection of TCO/emitter interfaces in superstrate thin-film photovoltaics, including emerging technologies like metal halide perovskites, while enabling high-efficiency, lightweight photovoltaics for space applications.

14 SOLAR ENERGY↗
DOE OSTI2023

Oxides related to cadmium telluride solar cells

Polycrystalline cadmium telluride (CdTe) is a leading material in photovoltaic technology due to its high absorption coefficient and near-optimum bandgap of 1.44 eV. It is known that CdTe film processing can promote surface oxidation depending on the growth environment and upon exposure to different oxidation conditions. For example, CdTeO3 forms when the CdTe film is treated in heated dry air, while in humid air, CdTe2O5 is detected. These oxides feature tellurium in the oxidation state +4 compared to the +2 state in CdTe. Other possible relevant oxides are CdO, TeO2, and TeO3. Using hybrid density functional calculations, we studied the electronic structure of these oxide materials and their band alignment to CdTe, which are essential parameters in the characterization of the interfaces at grain boundaries. The goal is to understand their stability and possible effects on passivating grain boundaries. The results are compared to the available experimental data.

14 SOLAR ENERGY↗
DOE OSTI2024

Perspective on Solar Energy Materials, Design and Discovery, Defects, Disorder, and Interfaces

The energy transition still faces a daunting math. Currently, more than three quarters of final energy consumption occurs in form of fuels vs less than one quarter in electricity. On the other hand, renewable energy additions come almost exclusively in the form of electricity (dominantly photovoltaics and wind). Thus, meeting the terawatt challenge requires enormous growth in renewables, sufficient to convert excess electricity into fuels, as well as the development of non-electricity based solar fuel technologies, for example via solar thermochemical routes. In this presentation, we will review successes and challenges in photovoltaic materials from silicon to CdTe to halide perovskites and potential emerging materials, with a particular perspective on the role of first principles calculations and predictions. Materials design and discovery is evolving to incorporate defects, disorder, and interfaces. These phenomena play also an important role in the thermochemical generation of hydrogen, allowing to utilize synergies between renewable electricity and fuels in computational research. At the same time, machine learning approaches are increasingly geared toward properties of non-ideal materials, for example defect formation, allowing the screening for more complex material behavior as needed for the respective applications.

fuels↗
DOE OSTI2024

Self-compensation of group-V acceptors in CdTe

Cadmium Telluride is at the core of an important thin-film technology for photovoltaics that is already commercially available, yet the CdTe-based solar cell efficiency remains limited at 22%, well below the theoretical limit of ~30%. Increasing the hole concentration is crucial for higher efficiency, and group-V elements such as As, P, and Sb are potential dopants as they are shallow acceptors. Nevertheless, group-V doped p-type CdTe often exhibits low doping activation, and the compensation source remains debated. Here, we performed hybrid density functional calculations with spin-orbit coupling to investigate possible sources of hole compensation in group-V doped CdTe. First, regarding possible self-compensation of the group-V dopants, we find that the formation of AX centers is unlikely since they are found to be unstable relative to the shallow acceptor forms. However, if the group-V dopants come in during growth (such as dimer molecules As2, P2, and Sb2), we find that the impurity atoms, which would occupy nearest neighbor sites, maintain the V-V bonds, limiting the hole density. For the native defects, our study reveals that Cd interstitial is the lowest energy donor defect in p-type CdTe. Still, it has a small migration barrier of 0.5 eV, making it highly mobile and unstable at room temperature. The Te vacancy is the next lowest formation energy donor. The migration barrier of 1.4 eV indicates that the Te vacancy is stable at room temperature. The antisite CdTe is also a donor, with low formation energy and stable at room temperature, potentially limiting the hole concentration. Our results, therefore, shed light on possible compensation centers and some guidance on how to avoid them.

14 SOLAR ENERGY↗
DOE OSTI2020

A Density Functional Theory (DFT) Study on the Effect of Chlorine in the Magnesium Zinc Oxide (MZO) Front Interface for Cadmium Telluride (CdTe) Thin Film Solar Cells

Cadmium telluride photovoltaics has benefitted greatly from the cadmium chloride treatment which causes a remarkable improvement in cell efficiencies. This work investigates the effect of elemental chlorine at the interface between the magnesium zinc oxide front contact and the cadmium telluride absorber in such a device. Band alignment including band bending and interface states and its role in potential charge carrier transport is the key feature studied. It is seen that a small amount of chlorine is leads to a more desirable band alignment. Higher concentrations of chlorine result in unfavorable band characteristics.

14 SOLAR ENERGY↗
DOE OSTI2022

Codesigning Alloy Compositions of CdSe y Te 1− y Absorbers and Mg x Zn 1− x O Contacts to Increase Solar Cell Efficiency

Thin‐film solar cells such as CdTe are a major commercial photovoltaic technology, with more than 25 GW installed worldwide and levelized costs of electricity competitive with fossil fuels. Further progress may result from integrating CdSe y Te 1− y absorbers with Mg x Zn 1− x O contacts, but the device efficiency is difficult to maximize due to coupled dependence on chemical composition of both alloys. Herein, a high‐throughput approach is demonstrated to codesign chemical compositions in alloyed Mg x Zn 1− x O/CdSe y Te 1− y thin‐film solar cells, using combinatorial libraries of PV devices with orthogonal composition gradients in CdSe y Te 1− y absorbers and Mg x Zn 1− x O contacts. It is found that the solar cell performance is a strong and coupled function of both elemental compositions, with efficiency up to 17.7% ( V OC = 836 mV, fill factor = 69%, J SC = 30.6 mA cm −2 ) at atomic compositions of Mg/(Mg + Zn) ≈18% and average Se/(Se + Te) ≈4%. These performance trends among >100 devices are explained by >100 ns lifetime of photoexcited charge carriers at the Mg x Zn 1− x O/CdSe y Te 1− y interface where strong Se accumulation is also observed. This study reports the optimal compositions of the commercially relevant Mg x Zn 1− x O/CdSe y Te 1− y solar cells and demonstrates a general approach to codesigning performance of alloyed thin‐film solar cells and other optoelectronic devices.

14 SOLAR ENERGY↗