Search NASA⌕ Search

SEARCH · Search NASA

Results for “Component Performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A Theoretical Analysis on the Dynamic Behavior and Electromechanical Response of PZT

Piezoelectric materials are used as a power source in stockpile components for safety and reliability assurances. The objective of this project is to gain insights into the fundamental pressure-induced behavior and electromechanical response of lead zirconate titanate (PZT). Specifically, to establish the basis for an accurate, physics-based material model for robust model-based design to rapidly optimize PZT-based materials and components for performance studies. Established ab-initio methods are used to interrogate and understand the dynamic behavior of PZT as a function of composition (50/50, 65/35, 80/20, 95/5) and dopants (La, Nb) to overcome the costly and time-consuming experimental methodologies. New cold curves for pure and doped single-crystal PZT are obtained as the reference equation-of-state (EOS). A negligible change in the pressure responses was observed for the systems and strains studied. Dielectric and piezoelectric responses of pure and doped single-crystal PZT were also calculated as a function of pressure. For undoped PZT, there is a clear and orderly pressure and composition dependence. For doped PZT, there is a significant increase in the responses, but the behavior is very disordered and inconclusive.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Computational Design of Cost-Effective High-Entropy Thermal/Environmental Barrier Coatings

Developing cost-effective thermal/environmental barrier coatings (TEBC) requires balance among various properties including low thermal conductivity, matching coefficient of thermal expansion (CTE), high thermal stability, high fracture toughness, and high recession resistance while being affordable. Low oxygen diffusivity is desirable as it can slow down oxygen transport to reach the underlying bond coating and hence delay oxidation of the bond coating. This project aims to design low-cost high-performance TEBC based on high entropy rare earth disilicates to protect SiC-based ceramic matrix composites from chemical and thermal attack for better performance of components in the hot section of gas turbine engines. To accelerate the TEBC design, we utilize first-principles density functional theory to predict key properties including phase stability, CTE, lattice thermal conductivity, temperature-dependent elastic constants, and oxygen diffusivity. Alloying elements including Yb, Y, Er, Eu, Gd, Lu, La, and Ce are considered, and modeling prediction are compared with available experimental results.

coefficient of thermal expansion↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at Oak Ridge National Laboratory and by laser powder directed energy deposition (LP-DED) at Idaho National Laboratory have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, and subsequent aging for 4 h at 800°C led to the formation of a high density of nano-size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and postheat treatments will be needed to fabricate high-performance 282 components for high-temperature nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at ORNL and laser powder directed energy deposition (LP-DED) at INL have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, while subsequent aging for 4 h at 800°C led to the formation of a high density of nano size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and post heat treatments will be needed to fabricate high performance 282 components for high temperature nuclear applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

ZiaCore Critical Experiment Demonstrates Key Technologies for Nuclear Energy Systems

ZiaCore is a LANL Laboratory Directed Research and Development (LDRD) project focused on developing and demonstrating key technologies for future nuclear energy systems. The project itself was split into three tasks: 1) Design of the ZiaCore Reactor, a UO2 fueled, graphite and zirconium-hydride (ZrH) moderated, heat pipe cooled micro-reactor 2) Development of the ZrH and heat pipes components 3) Performance of a critical experiment with a representative portion of the ZiaCore reactor incorporating the ZrH and heat pipes developed and made at LANL.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Shear-Wave Radiation Patterns from Explosive and Earthquake Sources in Scattering, Heterogeneous Media

Distinguishing whether a seismic event is an earthquake or an explosion is a core problem in explosion monitoring. For simplistic models, earthquakes produce a predictable S-wavefield based on their radiation pattern, while an explosion produces no S-wavefield. However, observations from nuclear tests show that explosions can produce significant S-wave energy on both horizontal components. We perform numerical experiments using SPECFEM to constrain when an S-wavefield generated from an explosion might differ from one produced by an earthquake. We generate the S-wavefield for our explosions by placing the source location within a small region consisting of large velocity heterogeneities. For the 2D cases investigated here, a crucial condition is that the size of the region of heterogeneities must be much smaller (approximately 1/12th) than the minimum wavelength of the wavefield for our simulation setups. We investigate both isotropic heterogeneities and anisotropic heterogeneities. Initial results demonstrate that the heterogeneous region lowers the P/S amplitude ratios of an explosion. The presence of strong anisotropic heterogeneities near the source can also produce an S-wavefield with similar amplitudes to the P-wavefield. Lastly, we show that S-wave polarization angles vary as a function of azimuth and distance for explosive sources in the presence of small-scale heterogeneities.

58 GEOSCIENCES↗
DOE OSTI2025

Realizing the Materials-Designed-To-Environments Promise of Additive Manufacturing Through a Fundamentally Different Approach to Optimization of Nonlinear Solid Mechanics Structures

Additive Manufacturing (AM) is expected to play a large role in the labs-wide goals of accelerating innovation and leading in modern engineering. More specifically, AM is seen as a key enabling technology for increasing the agility of nuclear deterrence and other national security applications involving complex coupled environments. However, the impact of AM on these initiatives has not been as wide-ranging as hoped because – despite its unique qualities – the focus has mostly been on detailed qualification to force AM components into pre-existing performance envelopes. This paradigm fundamentally precludes the novel possibilities afforded by the geometric and material flexibility of AM. In particular, the engineering of small-scale features to undergo buckling and contact can cause large geometric and symmetry changes which provide responsiveness to different environments. Despite almost a decade of observing such behavior, there exists no way to systematically design for AM to exploit it. Our goal for this project was to connect material design to multi-environment component performance by reconceptualizing how to design for AM to exploit the buckling and contact of small-scale features.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Model Based Approach to Extract Health Information from Textual Data

In current nuclear power plants (NPPs) a large amount of condition-based data is being generated and stored to assess and monitor component health and performance. The format of this data can be either numeric (e.g., pump vibration data) or textual (e.g., condition report which assess component health). While assessing component health from numeric data can be performed with a large variety of methods, the extraction of information from textual data still remains a challenge. Natural language processing (NLP) methods are starting to be deployed in current NPPs mainly to filter out incident reports (IRs) that are not safety related by employing supervised machine learning methods. However, these methods do not really provide the quantitative information that might be contained in IRs. This paper presents an approach to extract information from textual data (e.g., from IRs, maintenance reports) that is based on NLP data analytics methods coupled with model-based system engineer (MBSE) models. NLP methods are employed to perform syntactic and semantic analyses. Syntactic analysis analyzes the grammatical structure of a sentence; such analysis includes: part of speech (POS) tagging (i.e., identification of grammatic elements of each string - e.g., nouns, verbs), named entity recognition (i.e., identification of text entities - e.g., names, dates, events), and relation extraction (e.g., coreference resolution). On the other hand, semantic analysis is designed to analyze the logic structure of a sentence. Through a specific set of rules, our methods can identify whether a sentence contains health information of a component (e.g., degraded performance, anomaly behavior) or the causal relationship between two events (i.e., a cause-effect pair). An innovative element of our approach is that semantic analysis relies on MBSE models to identify links between textual elements. MBSE are diagrams designed to represent system and component dependencies (from both a form and functional point of view). In our approach, MBSE models emulate system engineer knowledge about component/system architecture. This paper presents in detail how the integration of NLP methods and MBSE models is performed. Few analysis examples focusing on centrifugal pumps are presented.

97 - MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Building Performance Standards and Energy Code Alignment - Technical Brief

Building energy codes focus on building design, construction and renovation and have significantly increased building efficiency since the first national energy code was published in 1975. Most jurisdictions have energy codes based on ANSI/ASHRAE/IES Standard 90.1 (hereto referred to as Standard 90.1) and the International Energy Conservation Code (IECC). Compliance options available in these model energy codes include a prescriptive path, whole building performance paths – including IECC Total Building Performance (TBP), Standard 90.1 Energy Cost Budget (ECB) method and Performance Rating Method (PRM) – and system performance paths for envelope and heating, ventilation, and air-conditioning systems. Building performance standard (BPS) policies are an emerging policy tool used by jurisdictions to reduce the operational energy use or greenhouse gas (GHG) emissions of the existing commercial building stock. BPS policies vary widely between jurisdictions and are tailored to each location’s climate and energy goals. Intuitively, projects that met a recent edition of the energy code should comply with the BPS targets. However, some new buildings may struggle with meeting the BPS for the following reasons: 1. Energy codes focus on the design of the building and its projected ability to perform efficiently, while BPS compliance is dependent on the actual ongoing performance of the building, considering variables like occupancy, operation, and maintenance. 2. There are significant differences in the methodologies used to determine BPS compliance versus code compliance, including how each handles compliance metrics, handling of building amenities, and renewable energy generation. 3. The prescriptive compliance path in the energy code is based on performance of individual building components, as opposed to the performance compliance path which accounts for holistic building design strategies and interdependent building systems. This can result in a significant variability in post-occupancy performance for buildings built using the prescriptive path. Designs on the lower end of the permitted efficiency range may struggle with meeting the BPS.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2025

Wide‐Field Bond Quality Evaluation Using Frequency Domain Thermoreflectance with Deep Neural Network Feature Reconstruction

Heterogeneous integration of microelectronic components provides a pathway to improve circuit/component performance; however, this comes with assembly challenges, in particular due to complex interfaces via subsurface bump bonds. The ability of these bonds to transmit electrical signals and conduct heat to the carrier substrate limits component performance. In this work, hyperspectral frequency‐domain thermoreflectance (FDTR) imaging is demonstrated as a robust technique for evaluating the quality of subsurface indium bump bonds in a surrogate microelectronic sample. By performing microscale FDTR imaging with coarse motion image stitching, thermal phase maps that cover a 4 mm by 4 mm field‐of‐view with subsurface feature sensitivity at depths greater than 50 µm are obtained. The resulting FDTR hyperspectral data contains more than three million pixels and reveal the quality of subsurface microbump arrays. Wide‐field analysis of bonded versus gap regions is enabled by deep neural network feature reconstruction, that after training, rapidly provides an interpretable representation of bond quality. Utility of noisy higher frequency FDTR phase maps, i.e., near the computationally predicted sensing depth limit, results in an average prediction error of 11%. Taken together, FDTR with neural network‐based analysis demonstrates subsurface bond monitoring at length scales relevant for heterogeneously integrated microelectronics.

FDTR↗
DOE OSTI2025

Performance Evaluation of LPBF Manufactured 316H Components

This work represents the continuation of a benchmark study that includes modeling, fabrication and characterization as demonstration to support industry’s adoption of advanced manufacturing processes in a variety of structures. This comprehensive study investigated the feasibility of using additive manufacturing (AM) technologies, specifically Laser Powder Direct Energy Deposition (LP-DED) and Laser Powder Bed Fusion (LPBF), to produce complex nuclear microreactor components using 316H stainless steel. The research focused on manufacturing an expanded elbow pipe component with transitioning sections, which are traditionally difficult and costly to produce through conventional manufacturing methods. The overall study’s primary objectives are therefore demonstrating AM viability for nuclear applications, optimizing process parameters, developing comprehensive material characterization protocols, validating computational modeling approaches, and establishing manufacturing guidelines for complex geometries. Although the initial work included the phased approach of cubical, upscaled cylindrical components, it is to enable to obtain more knowledge for the printing of the expanded elbow structure. The project achieved significant progress in process development by successfully optimizing LP-DED parameters to achieve 99.16-99.97% relative density in 316H stainless steel components. Through systematic evaluation of sixteen cube samples with varied laser powers (400-700W) and scan speeds (600-900 mm/min), optimal processing windows were identified at 500-550W with 600-700 mm/min or 650-700W with 650-900 mm/min scan speeds. The DED manufactured 316H demonstrated mechanical properties comparable or superior to wrought materials, with Young's modulus ranging from 153-208 GPa and controlled microstructural characteristics including greater than 95% face-centered cubic (FCC) phases and engineered cellular structures with sizes between 3.23-6.17 µm.

36 MATERIALS SCIENCE↗
DOE OSTI2024

From Data to Knowledge: A Graph-Based Reliability Approach to Assess System Health

With the goal of maximizing plant reliability and availability, complex systems such as nuclear power plants continuously monitor and record the performance and the health status of many components, assets, and systems. Such data may take the form of online monitoring data, condition reports, and maintenance reports and it carries the potential to provide system engineers with insights into anomalous behaviors or degradation trends as well as the possible causes behind them and to predict their direct consequences. The analysis of such data poses however few challenges. While some of these challenges are technical in nature (i.e., data are often distributed over several physical servers or databases), others are conceptual in nature (i.e., data elements come in different formats, numeric or textual), and measured values have different scales (e.g., vibration spectra and oil temperature). This paper directly tackles these challenges, and it focuses on the integration of all these data elements in order to assist plant system engineers in analyzing component, assets, and systems performances and optimize maintenance activities. This is performed by 1) extracting knowledge from textual data via technical language processing methods, and 2) quantifying system, asset, and component health from numeric condition-based data. We rely on model-based system engineering (MBSE) models of systems and assets to identify their architecture and functional (i.e., cause and effect) relations. Numeric and textual data elements are then associated with an MBSE graph element, based on their nature. This bonding of MBSE models and data elements constitutes a first-of-its-kind knowledge graph of a nuclear power plants system, with data elements being organized in a structured manner that enables system engineers to identify cause-effect trends in data elements and carry out appropriate actions in response.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Modeling and Experimental Validation of a Direct-Contact Counter-Flow Fluidized Bed Heat Exchanger for Thermal Energy Storage (TES) Applications

Particle-based thermal energy storage (TES) systems are an emerging energy storage technology. The technological advances have reduced costs, making TES more competitive and reliable in the marketplace but an efficient and reliable operation is heavily dependent on coherent heat transfer between air to particles or vice versa. The particle-based TES technologies provide an intermediate system that can store energy for short (0-10 h), long (10-200 h) and seasonal (> 200 h) timescales. The TES systems store energy by converting electricity to thermal energy; electricity can be directly sourced intermittent generation technologies and/or the grid, helping manage peak loads and other mismatches in supply and demand. The overall efficiency of the TES system depends on the performance of system components (particle storage silos and particle transfer mechanism etc.). The particle heat exchanger is one of the key system components that affects the system efficiency. The pressurized fluidized bed heat exchanger (PFB HX) performance is challenging to predict due to the chaotic behavior of particle and fluid interaction. This research presents a computational study of a novel direct-contact, counter-flow and air-to-particles PFB HX, that contributes in advancing the particle-based long-duration TES technologies. For the current analysis an unsteady Eulerian-Eulerian CFD model was developed and validated against experiments performed at the National Laboratory of the Rockies for two particle sizes (600 ..mu..m and 825 ..mu..m ). Following validation, parametric simulations were conducted to evaluate the effects of interphase drag models (Syamlal-O'Brien and Gidaspow), particle size, bed height and the influence of a frictional-viscosity term on hydrodynamics and heat transfer between the air & particles. The key findings from the analysis are: (1) for the studied operating window Syamlal-O'Brien provides superior agreement with measured gas temperatures (errors generally < 10%) while Gidaspow shows large deviations for the coarse particle case; (2) model predictions are most sensitive in the lower 0.2 m above the air distributor where bubble initiation and local mixing dominate interphase heat transfer; (3) representation of the distributor (number of inlet ports) materially affects predicted local mixing and temperature stratification; and (4) the Eulerian-Eulerian framework reproduces bulk thermal trends but shows regime dependent limitations for coarse particles, motivating mesoscale informed closures for scale-up analysis for future studies. These results provide validated guidance for drag selection and distributor design in particle-based thermal energy storage applications. Collectively, the validated model and parametric results quantify key drivers of PHB-HX performance and provide practical guidance for design and optimization. The results provide confidence in the model predictability and provide a step forward to improve on heat exchange performance. The demonstrated performance and modeling approach support the deployment and further development of this novel PHB-HX concept for robust, particle-based long-duration thermal energy storage systems.

25 ENERGY STORAGE↗
DOE OSTI2024

Advancements in Accelerator Physics and System Developments for the EIC

The development and enhancement of the Electron-Ion Collider (EIC) are founded on extensive research and development efforts aimed at achieving rigorous performance goals. This document outlines the crucial research and development (R&D) efforts that underpin the various systems and components of the EIC, including the polarized electron source and linear accelerator (linac) systems. Achieving the collider’s operational benchmarks relies on meticulously enhancing these components to optimize performance.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Standard Analysis Report INV-SAR-81, Revision 0 Chemical and Cement Components 2023 Inventory Estimates for the Interim State Performance Assessment of the Waste Isolation Pilot Plant

This standard analysis report provides the estimates for the chemical (oxyanions and complexing agents) and cement components with a data collection cut-off date of December 31, 2023. These estimates will be included in a Performance Assessment Inventory Report developed for the U.S. Department of Energy (DOE) interim state repository configuration performance assessment (PA) for the 2026 Compliance Recertification Application (CRA).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Gear Test Assembly - Experimental Testing and Analysis of Gears and Bearings - FY2026

The Gear Test Assembly (GTA) is an experimental test apparatus built and installed in the Mechanisms and Engineering Test Loop (METL) at Argonne National Laboratory (ANL). While designed to accommodate a variety of components intended for use in advanced compact in-vessel transfer machine, the focus of GTA been the testing of large radial spur gears. The performance of the components used in GTA motivates the choices made in the design, components, and material choices for the forthcoming METL test articles; the Gripper Test Assembly (GrTA), and the Bearing Test Assembly (BTA). To date, GTA has completed nine experimental testing campaigns and achieved over 21 million revolutions under prototypic sodium fast reactor loads and operating conditions. This report provides an overview and results for the two most recent experiments Campaign #8 and Campaign #9. `Campaign #8 was the first campaign to make use of a set of nickel alloy radial spur gears, made from Hastelloy C-22HS, and combined with heat-treated tapered roller bearings. The bearings and torque profile used allowed Campaign #8 to be directly compared with Campaign #1 where Inconel 718 gears were used instead. Campaign #8 attained 1,058,880 shaft revolutions within 23% of the 1,314,855 revolutions achieved in Campaign #1. These results demonstrate that the heat-treated tapered roller bearings show consistent increased lifetimes, approximately three times longer than for non heat-treated taper rollers, and that the particular material of the gear does not play a substantial role in performance. Similar to Campaign #7 where bearing failure resulted in fragmentation and transport of bearing material into the gear teeth led to tooth damage in the Inconel gears, a similar process led to the damage of the Hastelloy gears. Subsequent NDE analysis showed that the damage was only limited to the tooth surface and does not extend into the gear interiors. Based on the NDE reports, the Hastelloy gears can be reconditioned and put back into service for future campaigns as was done for the Inconel gears. Reconditioned Inconel 718 gears damaged in Campaign #7 were returned to service in Campaign #9 and paired with non heat-treated tapered roller bearings. In Campaign #9 a novel set of operating conditions were implemented whereby the gears and bearings were cycled between hot, submerged refueling conditions where fuel handling operations occurred and cold, dry, and inert conditions where the sodium was drained and the vessel was allowed to cool simulating long, ex-vessel storage of the fuel handling machine. A total of eight of these operating cycles were achieved before a bearing failure occurred after the accumulation of 475,692 shaft revolutions were achieved. During Campaign #9, one of the drive motors was damaged and over the course of a 240 day standby period, the entire GTA drive system was upgraded from a 480VAC system to a 240VAC system that provided the opportunity to consolidate wall-space in the METL facility and provide more space for additional test articles being installed in the coming year. The over 475,000 shaft revolutions achieved in Campaign #9 eclipses the previous record for lifetime of non heat-treated tapered roller bearings held by Campaign #3 of 392,000 shaft revolutions. Further analysis and future campaigns hope to shed light on the cause of this approximately 17% increase in lifetime.

42 ENGINEERING↗
DOE OSTI2025

Progress Towards Developing Neutron Tolerant Magnetostrictive and Piezoelectric Transducers

Current generation light water reactors (LWRs), sodium cooled fast reactors (SFRs), small modular reactors (SMRs), and next generation nuclear plants (NGNPs) produce harsh environments in and near the reactor core that can severely tax material performance and limit component operational life. To address this issue, several Department of Energy Office of Nuclear Energy (DOE-NE) research programs are evaluating the long duration irradiation performance of fuel and structural materials used in existing and new reactors. In order to maximize the amount of information obtained from Material Testing Reactor (MTR) irradiations, DOE is also funding development of enhanced instrumentation that will be able to obtain in-situ, real-time data on key material characteristics and properties, with unprecedented accuracy and resolution. Such data are required to validate new multi-scale, multi-physics modeling tools under development as part of a science-based, engineering driven approach to reactor development. It is not feasible to obtain high resolution/microscale data with the current state of instrumentation technology. However, ultrasound-based sensors offer the ability to obtain such data if it is demonstrated that these sensors and their associated transducers are resistant to high neutron flux, high gamma radiation, and high temperature. To address this need, the Advanced Test Reactor National Scientific User Facility (ATR-NSUF) is funding an irradiation, led by PSU, at the Massachusetts Institute of Technology Research Reactor to test the survivability of ultrasound transducers. As part of this effort, PSU and collaborators have designed, fabricated, and provided piezoelectric and magnetostrictive transducers that are optimized to perform in harsh, high flux, environments. Four piezoelectric transducers were fabricated with either aluminum nitride, zinc oxide, or bismuth titanate as the active element that were coupled to either Kovar or aluminum waveguides and two magnetostrictive transducers were fabricated with Remendur or Galfenol as the active elements. Pulse-echo ultrasonic measurements of these transducers are made in-situ. This paper will present an overview of the test design including selection criteria for candidate materials and optimization of test assembly parameters, data obtained from both out-of-pile and in-pile testing at elevated temperatures, and an assessment based on initial data of the expected performance of ultrasonic devices in irradiation conditions

Reinhardt1, Brian↗