SEARCH · Search NASA

Results for “Conductance decay”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS2016

Comparison of Spatial Correlation Parameters between Full and Model Scale Launch Vehicles

The current vibro-acoustic analysis tools require specific spatial correlation parameters as input to define the liftoff acoustic environment experienced by the launch vehicle. Until recently these parameters have not been very well defined. A comprehensive set of spatial correlation data were obtained during a scale model acoustic test conducted in 2014. From these spatial correlation data, several parameters were calculated: the decay coefficient, the diffuse to propagating ratio, and the angle of incidence. Spatial correlation data were also collected on the EFT-1 flight of the Delta IV vehicle which launched on December 5th, 2014. A comparison of the spatial correlation parameters from full scale and model scale data will be presented.

Kenny, Jeremy↗

NASA NTRS1984

Digital data-acquisition system for measuring the free decay of acoustical standing waves in a resonant tube

A low-cost digital system based on an 8-bit Apple II microcomputer has been designed to provide on-line control, data acquisition, and evaluation of sound absorption measurements in gases. The measurements are conducted in a resonant tube, in which an acoustical standing wave is excited, the excitation removed, and the sound absorption evaluated from the free decay envelope. The free decay is initiated from the computer keyboard after the standing wave is established, and the microphone response signal is the source of the analog signal for the A/D converter. The acquisition software is written in ASSEMBLY language and the evaluation software in BASIC. This paper describes the acoustical measurement, hardware, software, and system performance and presents measurements of sound absorption in air as an example.

Meredith, R. W.↗

NASA NTRS1986

The energetics of the gradual phase

Reseachers compare results with those in the chapter by Moore et al. (1980), who reached five main conclusions about the gradual phase: (1) the typical density of the soft X-ray emitting plasma is between 10 to the 11th power and 10 to the 12th power cm-3 for compact flares and between 10 to the 10th power and 10 to the 11th power cm-3 for a large-area flare; (2) cooling is by conduction and radiation in roughly equal proportions; (3) continual heating is needed in the decay phase of two-ribbon flares; (4) continual heating is probably not needed in compact events; (5) most of the soft-X-ray-emitting plasma results from chromospheric evaporation. The goal was to reexamine these problems with the data from the Solar Maximum Mission (SMM) and other supporting instruments as well as to take advantage of recent theoretical advances. SMM is capable of measuring coronal temperatures more accurately and with a better cadence than has been possible before. The SMM data set is also unique in that the complete transit of an active region was observed, with soft X-ray and UV images being taken every few minutes. Researcher's were therefore able to establish the pre-flare conditions of the region and see whether anything has changed as a result of the flare. The assumptions made in attempting to determine the required plasma parameters are described. The derived parameters for the five prime flares are presented, and the role of numerical simulations is discussed.

Strong, K. T.↗

NASA NTRS1985

Excitation study of the Lageos-derived Chandler wobble

Euler (1765) has deduced that any nonspherical rigid body which is rotating about some axis that is not its principal moment of inertia axis will experience a wobble as it rotates. The earth's wobble predicted by Euler was actually detected by Chandler (1891). The present paper is concerned with this wobble which is now known as the Chandler wobble. The Chandler wobble has now been under observation for more than 80 years. During part of this time, the amplitude of the wobble has actually been seen to grow. It follows that there must be some mechanisms operating to maintain (or excite) the Chandler wobble preventing it from decaying. Possible excitation mechanisms considered include earthquakes and meteorological variations. In this paper, an analysis is conducted of Lageos polar motion data for the period 1977-1983 to find out what can be learned from these data about the excitation mechanisms.

Gross, R. S.↗

NASA NTRS1995

Ice Processes and Growth History on Arctic and Sub-Arctic Lakes Using ERS-1 SAR Data

A survey of ice growth and decay processes on a selection of shallow and deep sub-Arctic and Arctic lakes was conducted using radiometrically calibrated ERS-1 SAR images. Time series of radar backscatter data were compiled for selected sites on the lakes during the period ot ice cover (September to June) for the years 1991-1992 and 1992-1993. A variety of lake-ice processes could be observed, and significant changes in backscatter occurred from the time of initial ice formation in autumn until the onset of the spring thaw. Backscatter also varied according to the location and depth of the lakes. The spatial and temporal changes in backscatter were most constant and predictable at the shallow lakes on the North Slope of Alaska. As a consequence, they represent the most promising sites for long-term monitoring and the detection of changes related to global warming and its effects on the polar regions.

Morris, K.↗

NASA NTRS2013

Granular Media-Based Tunable Passive Vibration Suppressor

and vibration suppression device is composed of statically compressed chains of spherical particles. The device superimposes a combination of dissipative damping and dispersive effects. The dissipative damping resulting from the elastic wave attenuation properties of the bulk material selected for the granular media is independent of particle geometry and periodicity, and can be accordingly designed based on the dissipative (or viscoelastic) properties of the material. For instance, a viscoelastic polymer might be selected where broadband damping is desired. In contrast, the dispersive effects result from the periodic arrangement and geometry of particles composing a linear granular chain. A uniform (monatomic) chain of statically compressed spherical particles will have a low-pass filter effect, with a cutoff frequency tunable as a function of particle mass, elastic modulus, Poisson fs ratio, radius, and static compression. Elastic waves with frequency content above this cutoff frequency will exhibit an exponential decay in amplitude as a function of propagation distance. System design targeting a specific application is conducted using a combination of theoretical, computational, and experimental techniques to appropriately select the particle radii, material (and thus elastic modulus and Poisson fs ratio), and static compression to satisfy estimated requirements derived for shock and/or vibration protection needs under particular operational conditions. The selection of a chain of polymer spheres with an elastic modulus .3 provided the appropriate dispersive filtering effect for that exercise; however, different operational scenarios may require the use of other polymers, metals, ceramics, or a combination thereof, configured as an array of spherical particles. The device is a linear array of spherical particles compressed in a container with a mechanism for attachment to the shock and/or vibration source, and a mechanism for attachment to the article requiring isolation (Figure 1). This configuration is referred to as a single-axis vibration suppressor. This invention also includes further designs for the integration of the single-axis vibration suppressor into a six-degree-of-freedom hexapod "Stewart"mounting configuration (Figure 2). By integrating each singleaxis vibration suppressor into a hexapod formation, a payload will be protected in all six degrees of freedom from shock and/or vibration. Additionally, to further enable the application of this device to multiple operational scenarios, particularly in the case of high loads, the vibration suppressor devices can be used in parallel in any array configuration.

Dillon, Robert P.↗

NASA NTRS2019

Bowles-Tatnall Wake Vortex Encounter Hazard Metric

Wake vortex spacing standards constrict the terminal area throughput and impose severe constraints on the overall capacity and efficiency of the National Airspace System. For more than two decades starting in the early 1990s, the National Aeronautics and Space Administration conducted extensive research on characterizing the formation and evolution of aircraft wakes. This multidisciplinary work included comprehensive field experiments (Pruis et al. 2016), flight tests (Vicroy et al. 1998), and wind tunnel tests (Rossow 1994; Chow et al. 1997). Parametric studies using large eddy simulations (Proctor 1998; Proctor et al. 2006) were conducted in order to develop fast-time models for the prediction of wake transport and decay (Ahmad et al. 2016). Substantial effort was spent on the formulation of acceptable vortex hazard metrics (Tatnall 1995; Hinton and Tatnall 1997). Several wake encounter severity metrics have been suggested in the past, which include the wake circulation strength, vortex-induced rolling moment coefficient (Clv), bank angle, and the roll control ratio (Tatnall 1995; Hinton and Tatnall 1997; Van der Geest 2012). The vortex-induced rolling moment coefficient introduced by Bowles and Tatnall (Tatnall 1995; Gloudemans et al. 2016) has been used extensively for risk and safety analysis of newly proposed air traffic management concepts and procedures. The original method of Bowles and Tatnall assumed a constant wing loading (the wing lift-curve slope, CL is constant), which resulted in an overestimation of the vortexinduced rolling moment coefficient. Bowles (2014) suggested a correction to the original method that provides more accurate values of Clv and which is also consistent with the underlying physics of the problem. The overestimation of Clv in the original method can be corrected by assuming an elliptical lift distribution. Figure 1.1 illustrates the correction in Clv achieved by the modified method.

Joel Malissa↗

NASA NTRS1976

Study of the decay and recovery of orbiting artificial space objects

The reentry of earth-orbiting space objects unconsumed in the atmosphere represents a potential hazard to populated areas of the earth. The Smithsonian Astrophysical Observatory has conducted a program called Moonwatch, whose purposes were to observe orbiting artificial satellites and reentries of space objects and, if possible, to recover and analyze reentered pieces. In addition, through observations of low-perigee objects, data obtained by Moonwatchers have been instrumental in defining some of the factors affecting satellite decay. The objectives of the program are presented, and the problems that enter into satellite-orbit and decay predictions are addressed. Moonwatchers contributed substantially to increasing an overall prediction capability, and some of the specific achievements over the 6-year period are cited.

Source record↗

NASA NTRS1975

Stress relaxation and mechanical properties of RL-1973 and PD-200-16 silicone resin sponge materials

Stress relaxation tests were conducted by loading specimens in double-lap shear to a preselected strain level and monitoring the decay of stress with time. The stress relaxation response characteristics were measured over a temperature range of 100 to 300 K and four strain levels. It is concluded that only a slight amount of stress relaxation was observed, and the stiffness increased approximately two orders of magnitude over the range of temperatures.

Saylak, D.↗

NASA NTRS2005

Hard X-ray Spectroscopic, Microwave and H-alpha Linear Polarization Studies with Hard X-Ray Observations from HESSI

The Principal Investigator (P.I.) has been pursuing a three year grant under NASA's Sun-Earth Connection Guest Investigator Program in support of the Ramaty High Energy Solar Spectroscopic Imager (RHESSI). An objective of these efforts is to combine X-ray and other data on solar flares, coronal mass ejections and interplanetary particle events in order to obtain a more comprehensive recognition of signatures, and understanding of interplanetary proton events. Thus, part of these efforts are to investigate if signatures seen in hard X-rays and microwaves can lead to better predictions of interplanetary proton events that can be dangerous to astronauts and spacecraft. The original proposal was written in May, 2000 and it discusses a three-pronged approach for data comparisons with three new types of instrumentation observing at X-ray, microwave and optical wavelengths. The major impetus behind this work and the proposal is that the P.I. discovered a strong correlation between a particular type of hard X-ray signature seen in spectral evolutions and interplanetary proton events (Kiplinger, 1995). The basic signature is that hard X-ray flux peaks either exhibit spectra that soften on their decays (Le. show fewer and fewer high energy X-rays with time) or they harden during decays (i.e. high energy X-rays decay significantly slower that lower energy X-rays). This signature is called progressive hardening. Studies were conducted over an eight-year period of data from the Hard X-Ray Burst Spectrometer (HXRBS) of the Solar maximum mission. Out of the 750 well observed flares studied, 41 flares had major associated proton events. Of these, 29 events were predicted on the basis of progressive hardening for a hit rate of 71%. The 152 largest flares had a hit rate of 82%.

Kiplinger, Alan L.↗

NASA NTRS2016

A Coupled Probabilistic Wake Vortex and Aircraft Response Prediction Model

Wake vortex spacing standards along with weather and runway occupancy time, restrict terminal area throughput and impose major constraints on the overall capacity and efficiency of the National Airspace System (NAS). For more than two decades, the National Aeronautics and Space Administration (NASA) has been conducting research on characterizing wake vortex behavior in order to develop fast-time wake transport and decay prediction models. It is expected that the models can be used in the systems level design of advanced air traffic management (ATM) concepts that safely increase the capacity of the NAS. It is also envisioned that at a later stage of maturity, these models could potentially be used operationally, in groundbased spacing and scheduling systems as well as on the flight deck.

Gloudemans, Thijs↗

NASA NTRS1983

Mass and energy balance in the 1973 August 9 flare

The mass and energy balance of the thermal plasma during the decay phase of the solar flare of August 9, 1973, are studied. The analysis is based on observationally determined values for the differential emission measure, density, turbulent and bulk velocities, and physical dimensions. The total particle content and total thermal energy content of the flare plasmas with temperatures above 100,000 K and their variation with time are calculated. The particle loss and the energy losses through radiation, conduction, and convection are evaluated. The decrease in total particle content can be accounted for by the convective losses through the loop footprints at 100,000 K. Radiation is the dominant energy loss mechanism although convective losses at 100,000 K can be important. Conductive losses at 100,000 K into cooler chromospheric material appear to be negligible. The decrease in the total energy content during the decay phase is equal to the sum of the energy losses over the period of observation. No requirement is found for continued heating during the decay phase.

Dere, K. P.↗

NASA NTRS1985

Multimuons events and primary composition

Nucleon decay detectors at large depths offers now a total area larger than 1000 sq m to registrate muons of energy exceeding 1 TeV. Near complete high energy muon families are detected in those arrays. An extensive 3D Monte-Carlo simulation was conducted in view to understand the spatial distribution of those events and the possible link with elementary act or primary composition. As pion or kaon parents have a very small decay probability at so high energy, multimuon phenomena occurs at high altitude where the atmospheric density is small after the most energetic collisions.

Acharya, B. S.↗

NASA NTRS2008

Simulating the Gradually Deteriorating Performance of an RTG

Degra (now in version 3) is a computer program that simulates the performance of a radioisotope thermoelectric generator (RTG) over its lifetime. Degra is provided with a graphical user interface that is used to edit input parameters that describe the initial state of the RTG and the time-varying loads and environment to which it will be exposed. Performance is computed by modeling the flows of heat from the radioactive source and through the thermocouples, also allowing for losses, to determine the temperature drop across the thermocouples. This temperature drop is used to determine the open-circuit voltage, electrical resistance, and thermal conductance of the thermocouples. Output power can then be computed by relating the open-circuit voltage and the electrical resistance of the thermocouples to a specified time-varying load voltage. Degra accounts for the gradual deterioration of performance attributable primarily to decay of the radioactive source and secondarily to gradual deterioration of the thermoelectric material. To provide guidance to an RTG designer, given a minimum of input, Degra computes the dimensions, masses, and thermal conductances of important internal structures as well as the overall external dimensions and total mass.

Wood, Eric G.↗

NASA NTRS1993

Human-in-the-loop evaluation of RMS Active Damping Augmentation

Active Damping Augmentation is the insertion of Controls-Structures Integration Technology to benefit the on-orbit performance of the Space Shuttle Remote Manipulator System. The goal is to reduce the vibration decay time of the Remote Manipulator System following normal payload maneuvers and operations. Simulation of Active Damping Augmentation was conducted in the realtime human-in-the-loop Systems Engineering Simulator at the NASA Johnson Space Center. The objective of this study was to obtain a qualitative measure of operational performance improvement from astronaut operators and to obtain supporting quantitative performance data. Sensing of vibratory motions was simulated using a three-axis accelerometer mounted at the end of the lower boom of the Remote Manipulator System. The sensed motions were used in a feedback control law to generate commands to the joint servo mechanisms which reduced the unwanted oscillations. Active damping of the Remote Manipulator System with an attached 3990 lb. payload was successfully demonstrated. Six astronaut operators examined the performance of an Active Damping Augmentation control law following single-joint and coordinated six-joint translational and rotational maneuvers. Active Damping Augmentation disturbance rejection of Orbiter thruster firings was also evaluated. Significant reductions in the dynamic response of the 3990 lb. payload were observed. Astronaut operators recommended investigation of Active Damping Augmentation benefits to heavier payloads where oscillations are a bigger problem (e.g. Space Station Freedom assembly operators).

Demeo, Martha E.↗

NASA NTRS1979

Computational simulation of corotational vortex merger using 0, 1, and 2 equation turbulence models

A computational study has been conducted to gain a better understanding of the role of turbulence in the merger of corotating vortices and in the decay of a single vortex. The flow field is simulated by using an inviscid flow model and zero-, one-, and two-equation turbulent-flow models. An implicit finite-difference procedure is employed to integrate the unsteady, two-dimensional, incompressible flow equations in a cross-plane. In the zero- and one-equation models, a spatially varying mixing-length model that simulates the streamline curvature effect is used to define an eddy viscosity. The computational merging distance criterion is in good agreement with the experimental one. In the case of the two-equation model, the turbulent kinetic energy and a modified rate of dissipation equation incorporating a curvature correction term are solved. A comparative study of the computational results corresponding to the various flow models and the available experimental data is presented.

Raj, P.↗

NASA NTRS1993

Streamwise vortex meander in a plane mixing layer

Previous measurements in a two-stream plane mixing layer have shown that the mean streamwise vorticity decays monotonically with downstream distance such that it is absent in the far-field (self-similar) region. It was not clear at that time if this measured decay was a result of actual vortex diffusion or increasing vortex meander within the mixing layer. The present experimental study was conducted in order to determine the existence of streamwise vortex meander in a mixing layer, and if present, its significance on the measured properties. The dependence of the velocity cross-correlation on the fixed probe location is considered a good indicator of the stationarity of the streamwise vortex location. The cross-correlation measurements obtained here indicate that the spanwise meander is negligible while the transverse apparent meander (normal to the plane of the mixing layer) is relatively large.

Leboeuf, Richard L.↗

NASA NTRS1961

An Experimental Investigation of the Damping of Liquid Oscillations in an Oblate Spheroidal Tank With and Without Baffles

An experimental investigation was conducted to determine the damping of the fundamental antisymmetric mode of oscillation of liquids contained in an oblate spheroidal tank. The decay of the fundamental mode was studied for a range of liquid depths in tanks with and without baffles. In the investigation of baffle effects, ring and cruciform baffles of various sizes were fixed at different locations within the tank. Data presented show the variation of the damping factor with tank fullness and with baffle type, width, location, and orientation as well as the effects of the amplitude of the liquid oscillations and of small variations in the liquid kinematic viscosity on the damping factor. The results of the investigation indicate that the addition of ring baffles to the tank results in an increase in the available effective damping when the baffle plane is in a region near the equilibrium liquid surface, and that cruciform baffles are effective in the damping of the fundamental mode in the near-empty tank. No apparent changes in damping for the tanks having ring baffles were observed as the kinematic viscosity of the liquid was varied over a small range.

Stephens, David G.↗