Search NASA⌕ Search

SEARCH · Search NASA

Results for “Confined Combustion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Mixing of Multiple Jets With a Confined Subsonic Crossflow: Opposed Rows of Orifices in Rectangular Ducts - Part 2

This paper summarizes experimental and computational results on the mixing of opposed rows of jets with a confined subsonic crossflow in rectangular ducts. The studies from which these results were excerpted investigated flow and geometric variations typical of the complex 3-D flowfield in the combustion chambers in gas turbine engines. The principal observation was that the momentum-flux ratio, J, and the orifice spacing, S/H, were the most significant flow and geometric variables. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. It also appeared that jet penetration remained similar with variations in orifice size, shape, spacing, and momentum-flux ratio when the orifice spacing was inversely proportional to the square-root of the momentum-flux ratio. It was also seen that planar averages must be considered in context with the distributions. Note also that the mass-flow ratios and the offices investigated were often very large (jet-to-mainstream mass-flow ratio greater than 1 and the ratio of orifices-area-to-mainstream-cross-sectional-area up to 0.5 respectively), and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations.

Holdeman, James D.↗
NASA NTRS1954

Investigation of Three Low-temperature-ratio Combustor Configurations in a 48-inch-diameter Ram-jet Engine

A preliminary evaluation was made of three types of combustor configurations in a 48-inch-diameter ram-jet engine to determine the one with the greatest promise of ultimately achieving efficient and stable combustion at low fuel-air rations and low combustor-inlet pressure. The combustor configurations evaluated include (1) a can-piloted configuration using a gutter-type flame holder with can-type pilot burners for stability, (2) an annular-piloted configuration using a gutter-type flame holder with an annular pilot burner to provide stability and to serve as a flow divider for confined fuel-air mixing, and (3) a can-type configuration using a flow divider for confined fuel-air mixing. No modifications were made to optimize the performance of any configuration. On the basis of this preliminary evaluation at an inlet-air temperature of about 990 degrees R, the annular-piloted combustor configuration appeared to have the greatest promise of permitting combustion efficiencies in excess of 0.90 at low fuel-air ratio with combustor-inlet pressures as low as 700 pounds per square foot absolute.

COMBUSTION - RAM-JET ENGINES↗
NASA NTRS1996

Mixing of Multiple Jets with a Confined Subsonic Crossflow in a Cylindrical Duct

This paper summarizes NASA-supported experimental and computational results on the mixing of a row of jets with a confined subsonic crossflow in a cylindrical duct. The studies from which these results were derived investigated flow and geometric variations typical of the complex 3-D flowfield in the combustion chambers in gas turbine engines. The principal observations were that the momentum-flux ratio and the number of orifices were significant variables. Jet penetration was critical, and jet penetration decreased as either the number of orifices increased or the momentum-flux ratio decreased. It also appeared that jet penetration remained similar with variations in orifice size, shape, spacing, and momentum-flux ratio when the number of orifices was proportional to the square-root of the momentum-flux ratio. In the cylindrical geometry, planar variances are very sensitive to events in the near wall region, so planar averages must be considered in context with the distributions. The mass-flow ratios and orifices investigated were often very large (mass-flow ratio greater than 1 and ratio of orifice area-to-mainstream cross-sectional area up to 0.5), and the axial planes of interest were sometimes near the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. The results shown also seem to indicate that non-reacting dimensionless scalar profiles can emulate the reacting flow equivalence ratio distribution reasonably well. The results cited suggest that further study may not necessarily lead to a universal 'rule of thumb' for mixer design for lowest emissions, because optimization will likely require an assessment for a specific application.

Holdeman, James D.↗
NASA NTRS1999

Mixing of Multiple Jets with a Confined Subsonic Crossflow: Opposed Rows of Orifices in Rectangular Ducts - Part 2

This paper summarizes experimental and computational results on the mixing of opposed rows of jets with a confined subsonic crossflow in rectangular ducts. The studies from which these results were excerpted investigated flow and geometric variations typical of the complex three-dimensional flowfield in the combustion chambers in gas turbine engines. The principal observation was that the momentum-flux ratio, J, and the orifice spacing, S/H, were the most significant flow and geometric variables. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. It also appeared that jet penetration remained similar with variations in orifice size, shape, spacing, and momentum-flux ratio when the orifice spacing was inversely proportional to the square-root of the momentum-flux ratio. It was also seen that planar averages must be considered in context with the distributions. Note also that the mass-flow ratios and the orifices investigated were often very large (jet-to-mainstream mass-flow ratio > 1 and the ratio of orifices-area-to-mainstream- cross-sectional-area up to 0.5, respectively), and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations.

Holdeman, J. D.↗
NASA NTRS1984

Mass and momentum turbulent transport experiments with confined swirling coaxial jets. I

An experimental study of mixing downstream of swirling coaxial jets discharging into an expanded duct was conducted to obtain data for the evaluation and improvement of turbulent transport models currently used in a variety of computational procedures throughout the combustion community. A combination of laser velocimeter and laser induced fluorescence techniques was employed to obtain mean and fluctuating velocity and concentration distributions which were used to derive mass and momentum turbulent transport parameters currently incorporated into various combustor flow models. Flow visualization techniques were also employed to determine qualitatively the time dependent characteristics of the flow and the scale of turbulence. Mean and fluctuating velocity profiles and probability density functions were obtained at selected axial and radial locations throughout the flow field. Mixing occurred in several steps of axial and radial mass transport and was coupled with a large radial mean convective flux. Major mixing regions were observed to occur (1) at the interface between the inner stream and the centerline recirculation zone, and (2) at the interface between the inner jet and the annular jet streams. Mixing for swirling flow was completed in one-third the length required for nonswirling flow.

Johnson, B. V.↗
NASA NTRS1986

Mass and momentum turbulent transport experiments with swirling confined coaxial jets. II

An experimental study of mixing downstream of swirling coaxial jets discharging into an expanded duct was conducted to obtain data for the evaluation and improvement of turbulent transport models currently used in a variety of computational procedures throughout the combustion community. A combination of laser velocimeter and laser induced fluorescence techniques was employed to obtain mean and fluctuating velocity and concentration distributions at selected axial and radial locations throughout the flow field. Flow visualization techniques were also employed to determine qualitatively the time dependent characteristics of the flow and the scale of turbulence. Simultaneous two component velocity and concentration/velocity measurements provided data which were used to determine the average momentum and mass transport rates for each of three measurement planes. Mixing for swirling flows occurred in several steps of axial and radial mean convective flow and was completed in one-third the length required for nonswirling flow. Comparison of the mass and momentum transport processes for swirling and nonswirling flows indicated that large differences existed in these processes between the two flows.

Roback, R.↗
NASA NTRS2001

Experiments Developed to Study Microgravity Smoldering Combustion

The overall objective of the Microgravity Smoldering Combustion (MSC) research program is to understand and predict smoldering combustion under normal and microgravity (near-zero-gravity) conditions to help prevent and control smolder-originated fires, in both environments. Smoldering is defined as a nonflaming, self-sustaining, propagating, exothermic surface reaction. If a material is sufficiently permeable, smoldering is not confined to its outer surface, but can propagate as a reaction wave through the interior of the material. The MSC program will accomplish its goals by conducting smolder experiments on the ground and in a space-based laboratory, and developing theoretical models of the process. Space-based experiments are necessary because smoldering is a very slow process and, consequently, its study in a microgravity environment requires extended periods of time that can only be achieved in space. Smoldering can occur in a variety of processes ranging from the smolder of porous insulating materials to underground coal combustion. Many materials can sustain smoldering, including wood, cloth, foams, tobacco, other dry organic materials, and charcoal. The ignition, propagation, transition to flaming, and extinction of the smolder reaction are controlled by complex, thermochemical mechanisms that are not well understood. As with many forms of combustion, gravity affects the availability of the oxidizer and the transport of heat, and therefore, the rate of combustion. The smoldering combustion of porous materials has been studied both experimentally and theoretically, usually in the context of fire safety. Smoldering encompasses a number of fundamental processes, including heat and mass transfer in a porous media; endothermic pyrolysis of combustible material; ignition, propagation, and extinction of heterogeneous exothermic reactions at the solid-gas pore interface; and the onset of gas phase reactions (flaming) from existing surface reactions. Smoldering presents a serious fire risk because the combustion can propagate slowly in a material's interior and go undetected for long periods of time. It typically yields a substantially higher conversion of fuel to toxic compounds than does flaming (though more slowly), and may undergo a sudden transition to flaming.

Vergilii, Franklin↗
NASA NTRS1999

Laminar Dust Flames: A Program of Microgravity and Ground Based Studies at McGill

Fundamental knowledge of heterogeneous combustion mechanisms is required to improve utilization of solid fuels (e.g. coal), safe handling of combustible dusts in industry, and solid propulsion systems. The objective of the McGill University research program on dust combustion is to obtain a reliable set of data on basic combustion parameters for dust suspensions (i.e. laminar burning velocity, flame structure, quenching distance, flammability limits, etc.) over a range of particle sizes, dust concentrations, and types of fuel. This set of data then permits theoretical models to be validated and, when necessary, new models to be developed to describe the detailed reaction mechanisms and transport processes. Microgravity is essential to the generation of a uniform dust suspension of arbitrary particle size and concentration. When particles with a characteristic size on the order of tens of microns are suspended, they rapidly settle in a gravitational field. To maintain a particulate in suspension for time duration adequate to carry out combustion experiments invariably requires continuous convective flow in excess of the gravitational settling velocity (which is comparable with and can even exceed the dust laminar burning velocity). This makes the experiments turbulent in nature and thus renders it impossible to study laminar dust flames. Even for small particle sizes on the order of microns, a stable laminar dust flow can be maintained only for relatively low dust concentrations at normal gravity conditions. High dust loading leads to gravitational instability of the dust cloud and to the formation of recirculation cells in the dust suspension in a confined volume, or to the rapid sedimentation of the dense dust cloud, as a whole, in an unconfined volume. Many important solid fuels such as carbon and boron also have low laminar flame speeds (of the order of several centimeters per second). Convection that occurs in combustion products due to buoyancy disrupts the low speed dust flames and makes observation of such flames at normal gravity difficult.

Goroshin, Sam↗
NASA NTRS1973

Swirling jet turbulent mixing and combustion computations

Computations are presented describing the mixing and combustion of swirling jets in a coaxial stream. It is demonstrated that the boundary layer equations represent the flow reasonably well until reversed flow is imminent. For the range of parameters investigated indications are that the edge velocity has little effect on the behavior of the flow. Furthermore, confining the flow with a constant pressure wall, or impressing a favorable pressure gradient on the coaxial flow, acts to reduce the severity of the centerline adverse pressure gradient created by the swirl decay. A simple scalar eddy viscosity model, including a potential core formulation, is shown to described the behavior of weak swirling flow in the far region but is only in fair agreement with observations in the near region. The effects of swirl on a burning hydrocarbon jet exhausting into a cold coaxial stream are shown to be intensified by the reduction of the density due to combustion. The enhanced mixing properties of high swirl flow produce rapid diffusion of the burning gases into the cold edge flow causing early cessation of the NO producing reactions. Computations show that doubling the initial jet swirl could reduce the NO production by 25 percent.

Rubel, A.↗
NASA NTRS1995

Microgravity combustion of dust clouds: Quenching distance measurements

The current level of physical understanding of dust combustion phenomena is still in a rudimentary state compared with the understanding of gas combustion processes. The reason for such a lack of fundamental understanding is partially based on the complexity of multiphase combustion and the enormous diversity of chemical-physical properties of heterogeneous combustible mixtures but is largely due to difficulties in the experimental investigation of dust combustion. The influence of gravity on a dust suspension is the main reason. First of all, when particulates (either solid particles or liquid droplets) with a characteristic size of the order of tens of microns are suspended, they rapidly settle in the gravitational field. To maintain a particulate suspension for a time duration adequate to carry out combustion experiments invariably requires continuous convection of particulates at or in excess of the gravitational settling velocity. Of necessity, this makes the experiments turbulent in character and makes it impossible to study laminar dust flames. For particle sizes of the order of microns a stable laminar dust flow can be maintained only for relatively small dust concentrations (e.g., for low fuel equivalence ratios) at normal gravity conditions. High dust loading leads to gravitational instability of the dust cloud and to the formation of recirculation cells in a dust suspension in a confined volume, or to the rapid sedimentation of the dense dust cloud as a whole in an unconfined volume. In addition, many important solid fuels such as low volatile coal, carbon, and boron have low laminar flame speeds (of the order of several centimeters per second). Gravitational convection that occurs in combustion products due to the buoyancy forces disrupts low speed dust flames and, therefore, makes observation of such flames at normal gravity impossible. The only way to carry out 'clean' fundamental experiments in dust combustion over a wide range of dust cloud parameters is in a gravity-free environment. Access to the microgravity environment provided by the use of large-scale drop towers, parabolic flights of aircraft and rockets, and shuttle and space station orbits has permitted now to proceed with a systematic program of dust combustion microgravity research. For example, the NASA-Lewis drop tower and a Lear jet parabolic flight aircraft were used by Ross et al. and by Berlad and Tangirala for experiments with Iycopodium/air mixtures. The Japan Microgravity Center drop shaft (JAMIC) where a microgravity condition of 10(exp -4) g for 10 s is available, was recently used by Kobayashi, Niioka et al. for measuring flame propagation velocities in polymethyl methacrylate dust/air suspensions. Microgravity dust combustion experiments were started at McGill University in the early 90's under the sponsorship of the Canadian Space Agency. Several generations of dust combustion platforms permitting dust combustion microgravity experiments to be carried out on board a parabolic flight aircraft (KC-135, NASA) have been designed and tested. The experimental data and experience gained from this research allowed us to design and build in a current phase of this program the microgravity apparatus for the visual observation of freely propagating constant pressure laminar dust flames. Quenching distances in aluminum dust suspensions have been measured in a wide range of dust cloud parameters in ground-based experiments and in recent microgravity experiments (KC-135 parabolic flights, Houston, February 1995).

Goroshin, S.↗
NASA NTRS1992

Flow enthalpy effects on scramjet mixing and combustion

The present analysis of the 3D characteristics of the mixing processes in a scramjet combustor gives attention to the streamwise, vorticity-driven macromixing, as well as shear-driven small-scale mixing, in both an unconfined Mach 6 airstream and a high-enthalpy (Mach-17) confined, Mach 6 airstream. The results obtained indicate that mixing is substantially lower for the high-enthalpy case. The effect of residence time on jet mixing is discussed in view of the production and decay of the axial vorticity, cross-flow velocities, and mean-flow velocities of these confined flows. The effective distance travelled by a fluid particle in the cross-flow, over the combustor length, is used to explain axial vorticity's contribution to mixing.

Riggins, D. W.↗
DOE OSTI2022

Elucidating the challenges in extracting ultra-slow flame speeds in a closed vessel - A CH 2 F 2 microgravity case study using optical and pressure-rise data

Refrigerants with a low global warming potential (GWP) possess mild flammability. Hence, a fundamental understanding of their combustion characteristics is required to assess their fire-hazardous potential. The laminar burning velocity is one fundamental property to describe these under safety evaluation aspects. However, measuring laminar burning velocities for slow-burning components, such as low-GWP alternatives, is challenging. This is due to influencing effects such as buoyant flame deformation, stretch, radiation, and confinement, especially at the flammability limits. Here, in the present study, we investigated near-limit flames of the representative refrigerant difluoromethane (CH 2 F 2 ) with nitrogen-enriched oxidizer mixtures to elucidate the potentials and limitations at ultra-slow flame speeds of two widely used flame speed measurement methods in the closed vessel configuration: the optical flame speed measurement in the early quasi-isobaric regime and the flame speed determination from the pressure-rise during the later phase of the isochoric combustion process. Experiments were performed under terrestrial- and microgravity, conducted in a specially designed setup suitable for drop tower applications, using both methods in parallel. Recommendations for the extraction of flame speed data are derived from the non-buoyant reference investigations under microgravity and transferred to ultra-slow flames at terrestrial gravity. Near-limit flames under microgravity were found to be significantly affected by stretch effects for the optical method so that flame speed extrapolations to unstretched conditions are prone to errors. Stretch also affects the pressure method’s lower evaluation limit, and errors can be estimated by combining flame speed data from the pressure method and Markstein lengths from optical experiments.

42 ENGINEERING↗
NASA NTRS1980

Flow measurements in a model swirl combustor

Flow measurements in a model combustor composed of two confined coaxial swirling jets under noncombusting conditions are presented. Mean flow results are obtained for five different flow conditions to determine the effect of outer swirl on the recirculation zone (which is used for flame stabilization under combustion conditions). As the outer swirl magnitude is first decreased from maximum counter-swirl to zero and then increased to give co-swirl conditions, the size and the reverse flow velocity in the recirculation zone diminish. Detailed time mean and fluctuating flow measurements are obtained for a co-swirl and a counter-swirl condition with a directional pitot probe and hot-wire anenometry. For these two cases, recirculation zone occurs only with counter-swirl, near the exit of the inner jet. The recirculation zone is in the form of a one celled toroidal vortex having very low swirl velocity. Axial development of fluctuation levels, energy dissipation rates and turbulence length scales are described for the two flow conditions. Spectral analysis reveals periodic oscillations in both flows. The oscillations originate from the inner jet and up to 4 harmonics are observed. The fundamental frequencies are comparable to the rotational frequencies of the inner jets at the exit which are approximately under solid body rotation. The significance of the present results for the combustion process is discussed.

Vu, B. T.↗
NASA NTRS1953

Free-jet Altitude Investigation of a 20-inch Ram-jet Combustor with a Rich Inner Zone of Combustion for Improved Low-temperature-ratio Operation

An investigation of the altitude performance of a 20-inch-diameter high-temperature-ratio ram-jet combustor which had been redesigned to provide good combustor efficiency over a wide range of temperature ratios was conducted at zero angle of attack in a free-jet facility at a Mach number of 3.0. Configurations investigated incorporated a cylindrical control sleeve which confined the injected fuel at low over-all fuel-air ratios to about 40 percent of the engine air flow. This provided an optimum fuel-air mixture over a portion of the flame holder when the over-all fuel-air ratio was about 0.02. The configurations with the control sleeve operated with good combustor efficiency at fuel-air ratios as lean as 0.015, whereas the original engine had a lean blow-out limit at a fuel-air ratio of about 0.03. The control sleeve had little effect upon the high-fuel-air-ratio performance of the engine.

COMBUSTION, RAM-JET ENGINES↗
NASA NTRS1998

Mixing of Multiple Jets With a Confined Subsonic Crossflow

Results from a recently completed enhanced mixing program are summarized in the two technical papers. These studies were parts of a High Speed Research (HSR)-supported joint Government/industry/university program that involved, in addition to the NASA Lewis Research Center, researchers at United Technologies Research Center, Allison Engine Company, CFD Research Corporation, and the University of California, Irvine. The studies investigated the mixing of jets injected normal to a confined subsonic mainsteam in both rectangular and cylindrical ducts. Experimental and computational studies were performed in both nonreacting and reacting flows. The orifice geometries and flow conditions were selected as typical of the complex three-dimensional flows in the combustion chambers in low-emission gas turbine engines. The principal conclusion from both the experiments and modeling was that the momentum-flux ratio J and orifice spacing S/H were the most significant flow and geometry variables, respectively. Conserved scalar distributions were similar-independent of reaction, orifice diameter H/d, and shape-when the orifice spacing and the square root of the momentum-flux ratio were inversely proportional. Jet penetration was critical, and penetration decreased as either momentum-flux ratio or orifice spacing decreased. We found that planar averages must be considered in context with the distributions. The mass-flow ratios and the orifices investigated were often very large. The jet-to-mainstream mass-flow ratio was varied from significantly less than 1 to greater than 1. The orifice-area to mainstream-cross-sectional-area was varied from approx. 0 to 0.5, and the axial planes of interest were often just downstream of the orifice trailing edge. Three-dimensional flow was a key part of efficient mixing and was observed for all configurations. As an example of the results, the accompanying figure shows the effects of different rates of mass addition on the opposite walls of a rectangular duct.

Holdeman, James D.↗
NASA NTRS1977

NO-NO2 measurements in a methane-fueled swirl-stabilized combustor

Exhaust plane measurements of NO and NO2 emissions from a methane-fueled swirl-stabilized combustor are reported. Samples were obtained by water-cooled probes and analyzed by chemiluminescent and UV absorption techniques. The combustor consists of two confined concentric jets having swirl. The inner jet flows premixed fuel and air, the outer jet is air. Variable outer jet swirl allows operation with jets swirling either in the same or opposite directions (co- or counter-swirl), and the combustion is stabilized by the resulting recirculation zone formed on the combustor centerline. Swirl conditions strongly affect the NOx emissions because of the influence of swirl on the combustion process. In the co-swirl conditions, the inner flow reaches high temperatures, and the correspondingly high NOx emissions are primarily NO. Under counter-swirl conditions much lower values of total NO are found, and these emissions are almost entirely NO2. In this case vigorous mixing in the inter-jet shear layer leads to severe flame quenching and lower temperatures. Formation of NO2 is associated with quenching processes in the combustor and is thought to be formed via NO oxidation by HO2 free radicals.

Oven, M. J.↗
NASA NTRS2014

Simulations of Turbulent Momentum and Scalar Transport in Confined Swirling Coaxial Jets

This paper presents the numerical simulations of confined three dimensional coaxial water jets. The objectives are to validate the newly proposed nonlinear turbulence models of momentum and scalar transport, and to evaluate the newly introduced scalar APDF and DWFDF equation along with its Eulerian implementation in the National Combustion Code (NCC). Simulations conducted include the steady RANS, the unsteady RANS (URANS), and the time-filtered Navier-Stokes (TFNS) with and without invoking the APDF or DWFDF equation. When the APDF or DWFDF equation is invoked, the simulations are of a hybrid nature, i.e., the transport equations of energy and species are replaced by the APDF or DWFDF equation. Results of simulations are compared with the available experimental data. Some positive impacts of the nonlinear turbulence models and the Eulerian scalar APDF and DWFDF approach are observed.

Shih, Tsan-Hsing↗