SEARCH · Search NASA

Results for “Correlation of Full-Scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1938

Full-Scale Wind-Tunnel Investigation of Wing Cooling Ducts, Special Report

The systematic investigation of wing cooling ducts at the NACA laboratory has been continued with tests in the full-scale wind tunnel on ducts of finite span. These results extend the previous investigation on section characteristics of ducts to higher Reynolds numbers and indicate the losses due to the duct ends. The data include comparisons between ducts completely within the ring and the conventional underslung ducts. Methods of flow regulation were studied and data were obtained for a wide range of internal duct resistance. The results show satisfactory correlation between the finite span and the previously measured section characteristics obtained with full-span ducts. The effects of the various design parameters on the duct characteristics are discussed. The cooling power required for the internal duct installation is shown to be only a small percentage of the engine power.

Nickle, F. R.↗

NASA NTRS1976

Vortex noise from nonrotating cylinders and airfoils

An experimental study of vortex-shedding noise was conducted in an acoustic research tunnel over a Reynolds-number range applicable to full-scale helicopter tail-rotor blades. Two-dimensional tapered-chord nonrotating models were tested to simulate the effect of spanwise frequency variation on the vortex-shedding mechanism. Both a tapered circular cylinder and tapered airfoils were investigated. The results were compared with data for constant-diameter cylinder and constant-chord airfoil models also tested during this study. Far-field noise, surface pressure fluctuations, and spanwise correlation lengths were measured for each configuration. Vortex-shedding noise for tapered cylinders and airfoils was found to contain many narrowband-random peaks which occurred within a range of frequencies corresponding to a predictable Strouhal number referenced to the maximum and minimum chord. The noise was observed to depend on surface roughness and Reynolds number.

Schlinker, R. H.↗

NASA NTRS1981

Designing for aircraft structural crashworthiness

This report describes structural aviation crash dynamics research activities being conducted on general aviation aircraft and transport aircraft. The report includes experimental and analytical correlations of load-limiting subfloor and seat configurations tested dynamically in vertical drop tests and in a horizontal sled deceleration facility. Computer predictions using a finite-element nonlinear computer program, DYCAST, of the acceleration time-histories of these innovative seat and subfloor structures are presented. Proposed application of these computer techniques, and the nonlinear lumped mass computer program KRASH, to transport aircraft crash dynamics is discussed. A proposed FAA full-scale crash test of a fully instrumented radio controlled transport airplane is also described.

Thomson, R. G.↗

NASA NTRS1981

Recent progress in V/STOL aircraft technology

Recent results from wind-tunnel and flight-tests investigations for V/STOL aircraft were reviewed. Primary emphasis is given to technical results relating to three types of subsonic aircraft: a quiet STOL aircraft; a tilt rotor aircraft, and a turbofan V/STOL aircraft. Comparison and correlation between theoretical and experimental results, and between wind-tunnel and flight-test results, is made. The quiet STOL aircraft technology results are primarily those derived from the NASA/Boeing Quiet Short Haul Aircraft (QSRA) program. The tilt rotor aircraft technology results are those obtained from the NASA/Army/Navy/Bell (XV-15-TRRA) aircraft flight investigations. The turbofan V/STOL aircraft technology results are from static ground facility and wind-tunnel investigations of a NASA/Navy/Grumman full-scale lift/cruise fan aircraft model, which features two tilting nacelles with TF-34 engines.

Roberts, L.↗

NASA NTRS1977

Experimental subsonic drag properties of the space shuttle orbiter TPS tiles

The drag characteristics of the space shuttle orbiter thermal protection system (TPS) tiles were studied experimentally in subsonic flow. Full-scale tiles were mounted to a 3.05 x 3.5 m test board in four configurations plus a completely smooth case. Pressure gradients were produced by tilting the board relative to the freestream. The drags due to steps, slots, and gaps between the tiles were evaluated at various orientations, pressure gradients, and Reynolds numbers. Results showed that the contribution of gaps and slots were minor compared to those of typical steps. The results for skin friction did not correlate as a fully rough surface. Thus, the surface area of the TPS tiles was sufficient to allow smooth-wall Reynolds number effects even though the steps between tiles could double the skin friction.

Norton, D. J.↗

NASA NTRS1982

Dynamic structural aeroelastic stability testing of the XV-15 tilt rotor research aircraft

For the past 20 years, a significant effort has been made to understand and predict the structural aeroelastic stability characteristics of the tilt rotor concept. Beginning with the rotor-pylon oscillation of the XV-3 aircraft, the problem was identified and then subjected to a series of theoretical studies, plus model and full-scale wind tunnel tests. From this data base, methods were developed to predict the structural aeroelastic stability characteristics of the XV-15 Tilt Rotor Research Aircraft. The predicted aeroelastic characteristics are examined in light of the major parameters effecting rotor-pylon-wing stability. Flight test techniques used to obtain XV-15 aeroelastic stability are described. Flight test results are summarized and compared to the predicted values. Wind tunnel results are compared to flight test results and correlated with predicted values.

Schroers, L. G.↗

NASA NTRS1974

Free-flight investigation of the stability and control characteristics of a STOL model with an externally blown jet flap

The stability and control characteristics of a four-engine turbofan STOL transport model having an externally blown jet flap have been investigated by means of the flying-model technique in the Langley full-scale tunnel. The flight characteristics of the model were investigated under conditions of symmetric and asymmetric (one engine inoperative) thrust at lift coefficients up to 9.5 and 5.5, respectively. Static characteristics were studied by conventional power-on force tests over the flight-test angle-of-attack range including the stall. In addition to these tests, dynamic longitudinal and lateral stability calculations were performed for comparison with the flight-test results and for use in correlating the model results with STOL handling-qualities criteria.

Parlett, L. P.↗

NASA NTRS1975

Pressure gradient effects on heat transfer to reusable surface insulation tile-array gaps

An experimental investigation was performed to determine the effect of pressure gradient on the heat transfer within space shuttle reusable surface insulation (RSI) tile-array gaps under thick, turbulent boundary-layer conditions. Heat-transfer and pressure measurements were obtained on a curved array of full-scale simulated RSI tiles in a tunnel-wall boundary layer at a nominal free-stream Mach number and free-stream Reynolds numbers. Transverse pressure gradients of varying degree were induced over the model surface by rotating the curved array with respect to the flow. Definition of the tunnel-wall boundary-layer flow was obtained by measurement of boundary-layer pitot pressure profiles, wall pressure, and heat transfer. Flat-plate heat-transfer data were correlated and a method was derived for prediction of heat transfer to a smooth curved surface in the highly three-dimensional tunnel-wall boundary-layer flow. Pressure on the floor of the RSI tile-array gap followed the trends of the external surface pressure. Heat transfer to the surface immediately downstream of a transverse gap is higher than that for a smooth surface at the same location. Heating to the wall of a transverse gap, and immediately downstream of it, at its intersection with a longitudinal gap is significantly greater than that for the simple transverse gap.

Throckmorton, D. A.↗

NASA NTRS1974

Effects of several factors on theoretical predictions of airplane spin characteristics

The influence of different mathematical and aerodynamic models on computed spin motion was investigated along with the importance of some of the aerodynamic and nonaerodynamic quantities defined in these models. An analytical technique was used which included the aerodynamic forces and moments acting on a spinning aircraft due to steady rotational flow and the contribution of the rotary derivatives to the oscillatory component of the total angular rates. It was shown that (1) during experimental-analytical correlation studies, the flight-recorded control time histories must be faithfully duplicated since the spinning motion can be sensitive to a small change in the application of the spin entry controls; (2) an error in the assumed inertias, yawing moments at high angle of attack, and initial spin entry bank angle do not influence the developed spin significantly; (3) damping in pitch derivatives and the center of gravity location play a role in the spinning motion; and (4) the experimental spin investigations conducted in a constant atmospheric density environment duplicate the Froude number only at the initial full-scale spin altitude (since the full-scale airplane at high altitudes experiences large density changes during the spin.)

Bihrle, W., Jr.↗

NASA NTRS1975

Design, fabrication, and test of a graphite/epoxy metering truss

A graphite/epoxy metering truss as applied to the large space telescope was investigated. A full-scale truss was designed, fabricated and tested. Tests included static limit loadings, a modal survey and thermal-vacuum distortion evaluation. The most critical requirement was the demonstration of the dimensional stability provided by the graphite/epoxy truss concept. Crucial to the attainment of this objective was the ability to make very sophisticated thermal growth measurements which was provided by a seven beam laser interferometer. The design of the basic truss elements were tuned to provide the high degree of dimensional stability and stiffness required by the truss. The struts and spider assembly were fabricated with Fiberite's AS/934 and HMS/934 broadgoods. The rings utilized T300 graphite fabricate with the same materials. The predicted performance of the truss was developed using the NASTRAN program. These results showed conformance with the critical stiffness and thermal distortion requirements and correlated well with the test results.

Oken, S.↗

NASA NTRS1973

Shockwave-boundary layer interference heating analysis.

Interference heating correlations have been developed based on existing wind tunnel test data taken with simple configurations such as wedge/flat plate and compression corner models. For turbulent flow, peak interference heating was first correlated with shock strength (pressure ratio across shock wave) and then as a function of Reynolds number. The peak interference Stanton number was found to exhibit the same Reynolds number and Prandtl number characteristics as the Stanton number variation for undisturbed flow over a flat plate. Similar correlations were developed for laminar flow. Results indicated that for laminar flow at higher Reynolds number, the impinging shockwave may act as a boundary layer trip and cause boundary layer transition resulting in high interference heating. The correlations derived in this study can be used to scale wind tunnel model test data to a full-scale space vehicle at supersonic or hypersonic flight conditions.

Hung, F. T.↗

NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an EBF STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An UTW powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An OTW configuration with non-decayer nozzle was about 10 db quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗

NASA NTRS1974

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Vonglahn, U.↗

NASA NTRS1974

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Von Glahn, U.↗

NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an externally blown flap (EBF) STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An under the wing (UTW) powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An over the wing (OTW) configuration with nondecayer nozzle was about 10 dB quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗

NASA NTRS1982

Effects of wing-leading-edge modifications on a full-scale, low-wing general aviation airplane: Wind-tunnel investigation of high-angle-of-attack aerodynamic characteristics

Wing-leading-edge modifications included leading-edge droop and slat configurations having full-span, partial-span, or segmented arrangements. Other devices included wing-chord extensions, fences, and leading-edge stall strips. Good correlation was apparent between the results of wind-tunnel data and the results of flight tests, on the basis of autorotational stability criterion, for a wide range of wing-leading-edge modifications.

Newsom, W. A., Jr.↗

NASA NTRS1982

The need for an optical transition detection system in the NTF

Methods for transition detection were studied. The very high test and model costs necessitate testing of any new configuration over a range of Reynolds numbers for correlation with data obtained in conventional tunnels. The Reynolds number variations will be carried out at constant dynamic pressure, i.e., constant aeroelastic condition, by varying test temperature. Boundary layer transition cannot be expected to occur at the full scale location at significantly less than full-scale Reynolds numbers, and transition patterns will change with varying Reynolds number. Knowledge of the location of transition on model surfaces is essential for correct interpretation of drag data. The importance of transition, the limitations of artificial transition fixing, and their relation to the NTF are reviewed. The calculated minimum roughness height to instantaneously trip transition on a model transport wing over a range of Reynolds numbers of interest is shown in the NTF.

Fancher, M. F.↗

NASA NTRS1947

Correlation of the Trim Limits of Stability Obtained for a PB2Y-3 Flying Boat and a 1/8-Size Powered Dynamic Model

Tests of a PB2Y-3 flying boat were made at the U.S> Naval Air Station, Patuxent River, Md., to determine its hydrodynamic trim limits of stability. Corresponding tests were also made of a 1/8-size powered dynamic model of the same flying boat in Langley tank no. 1. During the tank tests, the full-size testing procedure was reproduced as closely as possible in order to obtain data for a direct correlation of the results. As a nominal gross load of 66,000 pounds, the lower trim limits of the full-size and model were in good agreement above a speed of 80 feet per second. As the speed decreased below 80 feet per second, the difference between the model trim limits and full-scale trim limits gradually became larger. The upper trim limit of the model with flaps deflected 0 deg was higher than that of the full-size, but the difference was small over the speed range compared. At flap deflections greater than 0 deg, it was not possible to trim either the model of the airplane to the upper limit with the center of gravity at 28 percent of the mean aerodynamic chord. The decrease in the lower trim limits with increase in flap deflection showed good agreement for the airplane and model. The lower trim limits obtained at different gross loads for the full-size airplane were reduced to approximately a single curve by plotting trim against the square root of C(sub delta (sub o)) divided by C(sub V).

Garrison, Charlie C.↗