Search NASA⌕ Search

SEARCH · Search NASA

Results for “Creep rupture”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Structure and creep rupture properties of directionally solidified eutectic gamma/gamma-prime-alpha alloy

A simple ternary gamma/gamma-prime-alpha alloy of nominal composition (wt-%) Ni-32Mo-6Al has been directionally solidified at 17 mm/h and tested in creep rupture at 1073, 1173, and 1273 K. A uniform microstructure consisting of square-shaped Mo fibers in a gamma + gamma-prime matrix was found despite some variation in the molybdenum and aluminum concentrations along the growth direction. Although the steady-state creep rate is well described by the normal stress temperature equation, the stress exponent (12) and the activation energy (580 kJ/mol) are high. The rupture behavior is best characterized by the Larson-Miller parameter where the constant equals 20.

Whittenberger, J. D.↗
NASA NTRS1957

Effect of Overheating on Creep-rupture Properties of S-816 Alloy at 1,500 F

The effects of overheats to temperatures of 1650, 1800, 1900, and 2000 F were evaluated in terms of the changes in creep-rupture characteristics at 1500 F of S-816 alloy under stresses within the range of rupture strengths of the alloy for 100 to 1000 hours. Overheat periods were predominantly of 2-minute duration and were applied cyclically at approximately 5- or 12-hour intervals. The possible damage from overheating was believed to include internal metal structure changes induced by exposure to the higher temperatures and loss of life by creep if stress was present during the overheats.

ALLOYS, HEAT-RESISTING↗
DOE OSTI2025

Effect of stress on Laves phase precipitation in creep ruptured Grade 92 ferritic martensitic steel characterized by a novel accessible method

At high temperature conditions relevant to fossil and nuclear energy plants, Laves phase (Fe 2 X, X=Mo, W) precipitation is observed in common ferritic martensitic (FM) structural steels, with various reported effects on creep behavior. Despite being valuable metrics to correlate with mechanical properties and other precipitate phases, the volume fraction and number density of Laves phase precipitates has been difficult to quantify accurately using common techniques such as transmission electron microscopy (TEM) due to the relatively large size (∼0.25 μm) and low number density (∼10 11 cm −3 ) of Laves precipitates. Here, to address this characterization challenge, we developed and demonstrated a high-throughput and widely accessible method to quantify the volume fraction and number density of the Laves phase based on scanning electron microscope (SEM) images with a backscattered electron signal and the information depth (ID) of backscattered electrons. We applied this new technique in creep ruptured Grade 92 FM steel to study the effect of Laves phase on creep properties and determine the influence of stress on Laves phase precipitation. The quantitative accuracy of the SEM-based volume fraction and number density values was verified using synchrotron high energy X-ray diffraction and serial sectioning tomography. Stress did not significantly affect the Laves phase size or volume fraction during creep testing at 550 – 650°C and stress levels of 90 – 260 MPa (vs. unstressed conditions). Conversely, a moderate but statistically significant stress-enhanced increase in Laves phase number density, corresponding to an increase in nucleation rate, occurred during creep exposure above 110 MPa.

Creep↗
NASA NTRS2004

Characterization of C/Enhanced SiC Composite During Creep-Rupture Tests Using an Ultrasonic Guided Wave Scan System

An ultrasonic guided wave scan system was used to nondestructively monitor damage over time and position in a C/enhanced SiC sample that was creep tested to failure at 1200 C in air at a stress of 69 MPa (10 ksi). The use of the guided wave scan system for mapping evolving oxidation profiles (via porosity gradients resulting from oxidation) along the sample length and predicting failure location was explored. The creep-rupture tests were interrupted for ultrasonic evaluation every two hours until failure at approx. 17.5 cumulative hours.

Roth, Don J.↗
NASA NTRS1987

Creep-rupture behavior of a developmental cast-iron-base alloy for use up to 800 deg C

A promising iron-base cast alloy is being developed as part of the DOE/NASA Stirling Engine Systems Project under contract DEN 3-282 with the United Technologies Research Center. This report presents the results of a study at the Lewis Research Center of the alloy's creep-rupture properties. The alloy was tested under a variety of conditions and was found to exhibit the normal 3-stage creep response. The alloy compared favorably with others being used or under consideration for the automotive Stirling engine cylinder/regenerator housing.

Titran, Robert H.↗
NASA NTRS1988

Tensile and creep rupture behavior of P/M processed Nb-base alloy, WC-3009

Due to its high strength at temperatures up to 1600 K, fabrication of niobium base alloy WC-3009 (Nb30Hf9W) by traditional methods is difficult. Powder metallurgy (P/M) processing offers an attractive fabrication alternative for this high strength alloy. Spherical powders of WC-3009 produced by electron beam atomizing (EBA) process were successfully consolidated into a one inch diameter rod by vacuum hot pressing and swaging techniques. Tensile strength of the fully dense P/M material at 300-1590 K were similar to the arc-melted material. Creep rupture tests in vacuum indicated that WC-3009 exhibits a class 1 solid solution (glide controlled) creep behavior in the 1480 to 1590 K temperature range and stress range of 14 to 70 MPa. The creep behavior was correlated with temperature and stress using a power law relationship. The calculated stress exponent n, was about 3.2 and the apparent activation energy, Q, was about 270 kJ/mol. The large creep ductility exhibited by WC-3009 was attributed to its high strain rate sensitivity.

Hebsur, Mohan G.↗
NASA NTRS1973

Creep-rupture tests of internally pressurized Inconel 702 tubes

Seamless Inconel 702 tubes with 0.375-in. outside diameter and 0.025-in. wall thickness were tested to failure at temperatures from 1390 to 1575 F and internal helium pressures from 700 to 1800 psi. Lifetimes ranged from 29 to 1561 hr. The creep-rupture strength of the tubes was about 70 percent lower than that of sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.

Gumto, K. H.↗
NASA NTRS1980

Creep-rupture behavior of seven iron-base alloys after long term aging at 760 deg in low pressure hydrogen

Seven candidate iron-base alloys for heater tube application in the Stirling automotive engine were aged for 3500 hours at 760 C in argon and hydrogen. Aging degraded the tensile and creep-rupture properties. The presence of hydrogen during aging caused additional degradiation of the rupture strength in fine grain alloys. Based on current design criteria for the Mod 1 Stirling engine, N-155 and 19-9DL are considered the only alloys in this study with strengths adequate for heater tube service at 760 C.

Witzke, W. R.↗
NASA NTRS1973

Creep-rupture tests of internally pressurized Hastelloy-X tubes

Seamless Hastelloy-X tubes with 0.375-in. outside diameter and 0.025-in. wall thickness were tested to failure at temperatures from 1400 to 1650 F and internal helium pressures from 800 to 1800 psi. Lifetimes ranged from 58 to 3600 hr. The creep-rupture strength of the tubes was from 20 to 40 percent lower than that of sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.

Gumto, K. H.↗
NASA NTRS1993

Creep-Rupture Strength of a Ni-Base Superalloy at 1400 K

While NASAIR 100 is not the strongest of elevated-temperature single-crystal alloys, its higher-temperature properties are indicative of this technology's behavior. Attention is presently given to test results for this alloy which illuminate its 1400 K creep failure properties in air, and furnish a benchmark for the comparison of advanced materials to existing technology. The creep rupture behavior resembles that found after 1273 K testing, and is indicative of gamma-prime strengthening.

Whittenberger, J. D.↗
NASA NTRS1972

Creep-rupture tests of internally pressurized Rene 41 tubes

Weld-drawn tubes of Rene 41 with 0.935 centimeter outside diameter and 0.064 centimeter wall thickness were tested to failure at temperatures from 1117 to 1233 K and internal helium pressures from 5.5 to 12.4 meganewtons per square meter. Lifetimes ranged from 5 to 2065 hours. The creep-rupture strength of the tubes was 50 percent lower than that of unwelded, thick sheet specimens, and 20 percent lower than that of unwelded, thin sheet specimens. Larson-Miller correlations and photomicrographs of some specimens are presented.

Gumto, K. H.↗
NASA NTRS1977

Tensile and creep rupture properties of (16) uncoated and (2) coated engineering alloys at elevated temperatures

Sixteen test materials were supplied by NASA-Lewis Research Center as wrought bar or cast remelt stock. The cast remelt stock was cast into test blanks with two such materials being also evaluated after Jocoat coating was applied. Mechanical properties evaluated included tensile, modulus of elasticity, Poisson's Ratio, creep properties and creep rupture strength. Tests were conducted at temperatures applicable to the service temperature of the various alloys. This range extended from room temperature to 1000 C.

Fritz, L. J.↗
DOE OSTI2024

Measure the effect of molten halide salt exposure on creep rupture lifetime

Recent resurgence in the research and commercial interests in molten salt reactors (MSRs) as a viable advanced reactor concept to achieve the short- and long-term climate goals has resulted in ongoing efforts to demonstrate their commercial potential. These are relying on a combination of the extensive legacy knowledge from the molten salt reactor experiment (MSRE) and relatively recent data on materials compatibility of structural materials of interest such as 316H in molten salts environments. However, there is a critical lack of data on the mechanical behavior of alloys of interest for MSRS such as 316H, 617 and 709 in molten fluoride (FLiNaK or FLiBe) or chloride (NaCl-MgCl 2 ) salts. Limited legacy data from the molten salt reactor experiment (MSRE) program showed a significant reduction in creep rupture strength of a Ni-base alloy (Ni-15Cr-7Fe wt.%) in the molten fluoride NaF-ZrF4-UF4 (50-46-4 mol.%) salt. With ongoing efforts to commercialize different molten salt reactor concepts, the industry can considerably benefit from quantitative information on the impact of molten halide salts on the engineering properties such as creep and fatigue strength of materials of interest. Creep tests for 316H were conducted with fluoride (FLiNaK) and chloride (NaCl-MgCl 2 ) salts tat 650°C/150 MPa while alloys 709 and 617 were tested with FLiNaK at 700C/158 MPa and 750C.146 MPa respectively. Baseline tests were conducted in air to assess the impact of the molten salts on the creep behavior.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Measure the effect of molten halide salt exposure on creep rupture lifetime

Recent resurgence in the research and commercial interests in molten salt reactors (MSRs) as a viable advanced reactor concept to achieve the short- and long-term climate goals has resulted in ongoing efforts to demonstrate their commercial potential. These are relying on a combination of the extensive legacy knowledge from the molten salt reactor experiment (MSRE) and relatively recent data on materials compatibility of structural materials of interest such as 316H in molten salts environments. However, there is a critical lack of data on the mechanical behavior of alloys of interest for MSRS such as 316H, 617 and 709 in molten fluoride (FLiNaK or FLiBe) or chloride (NaCl-MgCl 2 ) salts. Limited legacy data from the molten salt reactor experiment (MSRE) program showed a significant reduction in creep rupture strength of a Ni-base alloy (Ni-15Cr-7Fe wt.%) in the molten fluoride NaF-ZrF4-UF4 (50-46-4 mol.%) salt. With ongoing efforts to commercialize different molten salt reactor concepts, the industry can considerably benefit from quantitative information on the impact of molten halide salts on the engineering properties such as creep and fatigue strength of materials of interest. Creep tests for 316H were conducted with fluoride (FLiNaK) and chloride (NaCl-MgCl 2 ) salts tat 650°C/150 MPa while alloys 709 and 617 were tested with FLiNaK at 700C/158 MPa and 750C.146 MPa respectively. Baseline tests were conducted in air to assess the impact of the molten salts on the creep behavior.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1978

Interpolation and extrapolation of creep rupture data by the minimum commitment method. II - Oblique translation

An outline is presented of a new procedure, termed the oblique translation method, which emerged in the development of the focal point convergence method. Approaches for implementing the oblique translation method are discussed. It is shown that the new method is essentially a minimum commitment method when manually-graphically implemented, in the sense that the form of the functions involved are not forced into particular analytical forms. The individual constants and functions are independently determined. The minimum commitment concept is extended to the analysis of creep rupture data wherein each isothermal is to be generated by an oblique translation of the 'master curve' when plotted. Attention is given to a manual-graphical analysis, the preassessment of data, and an analysis by computer code.

Manson, S. S.↗
NASA NTRS1971

Sensitivity of the creep-rupture properties of Waspaloy sheet to sharp-edged notches in the temperature range 1000-1400 deg F.

Time-dependent notch sensitivity of Waspaloy was observed at test temperatures from 1000 to 1300 deg F. Its occurrence in this range was dependent on the heat treatment. ?Overaging' eliminated the notch sensitivity. Optimum combination of smooth and notched specimen strengths for material solution treated at 1975 deg F were obtained by aging 24 hr at 1550 deg F. Necessary conditions for time-dependent notch sensitivity were (1) the notch specimen loads had to be below the approximate 0.2 percent offset yield strength; and (2 ) test data from smooth specimens had to indicate that small amounts of creep used up large fractions of creep-rupture life. No reasons were evident why these criteria will not prove applicable to other alloys.

Wilson, D. J.↗
NASA NTRS1988

Creep-rupture performance of superalloys in high-pressure hydrogen environment

The advantages of the automotive Stirling engine presented, which employs high-pressure hydrogen as a working fluid, include (in addition to a 50-percent improvement in efficiency over internal combustion engines) multiple-fuel capability, low pollution, and low noise. The severe service conditions associated with the 870 C operation and 15 MPa hydrogen working fluid have prompted the present suitability testing of six tube and four cast Fe-base alloys. While stress-rupture life and minimum creep rates were not affected, both tube and cast alloy types underwent creep ductility degradation.

Bhattacharyya, S.↗