Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cross Flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

A viscous vortex lattice method for analysis of cross-flow propellers and turbines

Marine hydrokinetic turbines are a promising source of renewable energy, but the costs of existing cross-flow turbine designs are too high. In order to develop new designs with reduced costs, there exists a need for a low-order computational model that is simultaneously fast, accurate, and robust. In this report we present a novel theoretical model for the analysis of cross-flow propellers and turbines based on the vortex lattice method (VLM). In order to overcome the limitation that the VLM ignores viscous effects (such as trailing-edge flow separation), we present a novel method to account for viscous-thickness-load coupling (VTLC). In order to overcome the difficulty that wake passages cause the VLM to be unstable, we present the panel-averaged induced velocity for the influence of wake vortices on the blades. Herein, we describe our model and provide verification versus RANS CFD. Results show that our VLM + VTLC model predictions are three times more accurate than prior low-order models (i.e. three times lower root mean square error to high-fidelity RANS results) yet 10,000 times faster than RANS over a wide range of operating conditions.

16 TIDAL AND WAVE POWER↗

Bubble Formation from Wall Orifice in Liquid Cross-Flow Under Low Gravity

Two-phase flows present a wide variety of applications for spacecraft thermal control systems design. Bubble formation and detachment is an integral part of the two phase flow science. The objective of the present work is to experimentally investigate the effects of liquid cross-flow velocity, gas flow rate, and orifice diameter on bubble formation in a wall-bubble injection configuration. Data were taken mainly under reduced gravity conditions but some data were taken in normal gravity for comparison. The reduced gravity experiment was conducted aboard the NASA DC-9 Reduced Gravity Aircraft. The results show that the process of bubble formation and detachment depends on gravity, the orifice diameter, the gas flow rate, and the liquid cross-flow velocity. The data are analyzed based on a force balance, and two different detachment mechanisms are identified. When the gas momentum is large, the bubble detaches from the injection orifice as the gas momentum overcomes the attaching effects of liquid drag and inertia. The surface tension force is much reduced because a large part of the bubble pinning edge at the orifice is lost as the bubble axis is tilted by the liquid flow. When the gas momentum is small, the force balance in the liquid flow direction is important, and the bubble detaches when the bubble axis inclination exceeds a certain angle.

Nahra, Henry K.↗

Cross-Flow Filtration of Multiple Algal Strains and Mixed Populations Using Embedded Membranes

The objective of this research is to analytically assess cross-flow membrane filtration (CFF) technology as an algal harvesting approach that will debottleneck the water recovery/nutrient recovery/recycling processes. Specifically, the focus of this investigation will be INL-developed, ceramic-embedded, erosion-resistant membrane technology, comprising stainless steel micro- and ultra-filters with controlled pore sizes to reduce membrane fouling and enhance filtration permeation properties. Parameters such as shear/face velocity and transmembrane pressure will be varied to assess impact on filtration efficiency. Detrimental effects such as cell lysis must also be considered. The project is an opportunity to analytically investigate the level of shear (cross-flow face velocity level) needed to accomplish dewatering by filtration in an economic manner while gaining insight into membrane fouling mechanisms. Furthermore, testing of the membranes with different starting concentrations of algae, as well as with a variety of membranes and filtration conditions, will allow us to establish the boundary conditions where membrane technologies are appropriate for application in an overall algal harvesting strategy.

09 BIOMASS FUELS↗

Nonlinear stability of non-stationary cross-flow vortices in compressible boundary layers

The nonlinear evolution of long wavelength non-stationary cross-flow vortices in a compressible boundary layer is investigated and the work extends that of Gajjar (1994) to flows involving multiple critical layers. The basic flow profile considered in this paper is that appropriate for a fully three-dimensional boundary layer with O(1) Mach number and with wall heating or cooling. The governing equations for the evolution of the cross-flow vortex are obtained and some special cases are discussed. One special case includes linear theory where exact analytic expressions for the growth rate of the vortices are obtained. Another special case is a generalization of the Bassom & Gajjar (1988) results for neutral waves to compressible flows. The viscous correction to the growth rate is derived and it is shown how the unsteady nonlinear critical layer structure merges with that for a Haberman type of viscous critical layer.

Gajjar, J. S. B.↗

A study of viscous cross-flow effects on circular cylinders at high Reynolds numbers

Results of experimental studies on viscous cross-flow over circular cylinders for Reynolds numbers from 0.15 x 10 to the 6th to 10.9 x 10 to the 6th at Mach numbers of less than 0.3 are presented and compared with previous work where possible. Results presented include the variation of static cross-flow drag coefficients with both Reynolds number and ratio of surface roughness to model diameter, the variation of Strouhal number with Reynolds number and the dynamic variation of surface static pressure coefficients with both angular position around the cylinder and Reynolds number. The effects of end-plates on flow around two-dimensional bluff-bodies and of tunnel blockage on drag measurements are also discussed.

James, W. D.↗

Reduction of Jet Penetration in a Cross-Flow by Using Tabs

A tab placed suitably on a nozzle that produces a jet in a cross-flow can reduce the penetration of the jet. This effect, achieved when the tab is placed on the windward side of the nozzle relative to the cross flow, may be of interest in film cooling applications. Wind tunnel experiments are carried out, in the momentum ratio (J) range of 10-90, to investigate the tab geometry that would maximize this effect. The preliminary results show that a 'delta tab' having a base width approximately fifty percent of the nozzle diameter may be considered optimum. With a given tab size, the effect is more pronounced at higher J. Reduction in jet penetration by as much as 40% is observed. Comparable reduction in jet penetration is also obtained when a triangular shaped tab is placed flush with the tunnel wall or with its apex tilted down into the jet nozzle (the 'delta tab' being the configuration in which the apex is tilted up). However, the delta tab involves the least flow blockage and pressure loss. Relative to the baseline case, the lateral spreading of the jet is found to be more with the delta tab but less with other orientations of the tab.

Zaman, K. B. M. Q.↗

Influence of cross-flow on nonlinear Tollmien-Schlichting/vortex interaction

The transition of an incompressible three-dimensional boundary layer with strong cross-flow is considered theoretically and computationally in the context of vortex/wave interactions. Specifically the work centers on two lower-branch Tollmien-Schlichting waves which mutually interact nonlinearly to induce a longitudinal vortex flow. The vortex motion in turn gives rise to significant wave modulation via wall-shear forcing. The characteristic Reynolds number is large and, as a consequence, the waves' and the vortex motion are governed primarily by triple deck theory. The nonlinear interaction is captured by a viscous partial-differential system for the vortex coupled with a pair of amplitude equations for each wave pressure. Following analysis and computation over a wide range of parameters, three distinct responses are found to emerge in the nonlinear behavior of the flow solution downstream: an algebraic finite-distance singularity, far-downstream saturation or far-downstream wave decay leaving pure vortex flow. These depend on the input conditions, the wave angles and the size of the cross flow.

Davis, D. A. R.↗

Cross flow characteristics in a three fuel assemblies

To evaluate the reactor thermal margin of APR+, reactor core flow distribution including both axial and lateral directional hydraulic resistances of fuel assemblies should be known. 3-Ch cross flow test facility has been constructed with three full-size fuel assemblies to investigate the cross flow characteristics. Performance tests have been performed. The axial and lateral directional hydraulic resistances of fuel assemblies have been measured. The test results have been compared to the CFD calculation. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Active Control of Jets in Cross-Flow for Film Cooling Applications

Jets in cross-flow have applications in film cooling of gas turbine vanes, blades and combustor liners. Their cooling effectiveness depends on the extent to which the cool jet-fluid adheres to the cooled component surface. Lift-off of the cooling jet flow or other mechanisms promoting mixing, cause loss of cooling effectiveness as they allow the hot "free-stream" fluid to come in contact with the component surface. The premise of this project is that cooling effectiveness can be improved by actively controlling (e.9. forcing, pulsing) the jet flow. Active control can be applied to prevent/delay lift-off and suppress mixing. Furthermore, an actively controlled film-cooling system coupled with appropriate sensory input (e.g. temperature or heat flux) can adapt to spatial and temporal variations of the hot-gas path. Thus, it is conceivable that the efficiency of film-cooling systems can be improved, resulting in coolant fluid economy. It is envisioned that Micro Electro-Mechanical Systems (MEMS) will play a role in the realization of such systems. As a first step, a feasibility study will be conducted to evaluate the concept, identify actuation and sensory elements and develop a control strategy. Part of this study will be the design of a proof-of-concept experiment and collection of necessary data.

Nikitopoulos, Dimitris E.↗

Mechanisms of Flame Stabilization and Blowout in a Reacting Turbulent Hydrogen Jet in Cross-Flow

The mechanisms contributing to flame stabilization and blowout in a nitrogen-diluted hydrogen transverse jet in a turbulent boundary layer cross-flow (JICF) are investigated using three-dimensional direct numerical simulation (DNS) with detailed chemistry. Non-reacting JICF DNS were performed to understand the relative magnitude and physical location of low velocity regions on the leeward side of the fuel jet where a flame can potentially anchor. As the injection angle is reduced from 90{sup o} to 70{sup o}, the low velocity region was found to diminish significantly, both in terms of physical extent and magnitude, and hence, its ability to provide favorable conditions for flame anchoring and stabilization are greatly reduced. In the reacting JICF DNS a stable flame is observed for 90{sup o} injection angle and, on average, the flame root is in the vicinity of low velocity magnitude and stoichiometric mixture. When the injection angle is smoothly transitioned to 75{sup o} a transient flame blowout is observed. Ensemble averaged quantities on the flame base reveal two phases of the blowout characterized by a kinematic imbalance between flame propagation speed and flow normal velocity. In the first phase dominant flow structures repeatedly draw the flame base closer to the jet centerline resulting in richer-than-stoichiometric mixtures and high velocity magnitudes. In the second phase, in spite of low velocity magnitudes and a return to stoichiometry, due to jet bending and flame alignment normal to the cross-flow, the flow velocity normal to the flame base increases dramatically perpetuating the blowout.

08 HYDROGEN↗

Theoretical analyses of aerosol aging on a substrate without wall-effects by a cross-flow

Long time ({approx}1 day) aging or reactions of aerosol is typically studied using either large aerosol chambers (> 10 m3) or particles supported on a substrate to minimize wall effects. To avoid wall effects in the latter, it is often essential that the wall reactivity be extremely small (<< 10-5 reactions per encounter) and that the particle loadings be very small (< 1 pg/cm2) to eliminate transport-limited trace gas depletion near the particles and substrate. We evaluate here a cross-flow approach, which greatly reduces these constraints. Particles are to be supported on a micromesh ({approx}50% or more open area) through which the reactive gas is drawn at around a few hundred cm/s. The analysis shows how the competitions between flow and diffusion establishes a 'zone of isolation' several microns wide around each reactive particle, outside of which the reactivity of other particles or the substrate are irrelevant to the local reactions. This cross-flow approach reduces the effects of substrate and collective particle reactivity typically orders of magnitude, and will facilitate aging studies of supported aerosols.

54 ENVIRONMENTAL SCIENCES↗

Round jet in a cross flow - Influence of injection angle on vortex properties

A model is developed to infer the properties of a pair of diffuse contrarotating vortices for perpendicular jet injection into the cross flow. Attention is given to pressure distribution on the surface where the jet exhausts, especially in terms of V/STOL applications. A V/STOL wind tunnel experiment is described, whereby a round jet of air (10.16 cm dia) was discharged through a horizontal flat plate into the cross flow of the wind tunnel test section at angles of 45, 60, 75, and 90 deg. Results indicate that the effective vortex strength for both velocity ratios is highest near the jet orifice, and decreases as the vortices are swept downstream, at which point the effective vortex spacing increases. In addition, the core radius of the vortex exhibits properties similar to those of the effective vortex spacing

Krausche, D.↗

Performance Data from a 1-Meter Cross-flow Turbine with High Deflection Hydrofoils

Performance data of a 1-meter diameter cross-flow tidal turbine consisting of three NACA 0018 blades with two support struts with high deflection hydrofoils. Data was collected at the University of New Hampshire Jere A. Chase Ocean Engineering Lab within the tow tank. Three turbine parameters were varied: the blade materials, blade shape, and support strut position. A detailed description of the testing set-up and data files contained within the compressed "Turbine_Performance_Data.zip" file is in the "ReadMe.txt" file. Review of the original dataset "_Ver1" found that one of the tests had issues with one of the two redundant sensors. Resources were updated by replacing the dataset with measurements from the redundant sensor and are provided as version 2 "_Ver2".

16 TIDAL AND WAVE POWER↗

Multi-mode evaluation of power-maximizing cross-flow turbine controllers

A general method for predicting and evaluating the performance of three candidate cross-flow turbine power-maximizing controllers is presented in this paper using low-order dynamic simulation, scaled laboratory experiments, and full-scale field testing. For each testing mode and candidate controller, performance metrics quantifying energy capture (ability of a controller to maximize power), variation in torque and rotation rate (related to drive train fatigue), and variation in thrust loads (related to structural fatigue) are quantified for two purposes. First, for metrics that could be evaluated across all testing modes, we considered the accuracy with which simulation or laboratory experiments could predict performance at full scale. Second, we explored the utility of these metrics to contrast candidate controller performance. For these turbines and set of candidate controllers, energy capture was found to only differentiate controller performance in simulation, while the other explored metrics were able to predict performance of the full-scale turbine in the field with various degrees of success. Finally, effects of scale between laboratory and full-scale testing are considered, along with recommendations for future improvements to dynamic simulations and controller evaluation.

13 HYDRO ENERGY↗