Search NASA⌕ Search

SEARCH · Search NASA

Results for “DAMPER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

An active nutation damper for spacecraft

An active nutation damping device, consisting of an angular accelerometer, a dc-motor-driven flywheel, and associated electronics, developed for spacecraft use is described. This damping system was used on the LAGEOS spacecraft to control nutation buildup during the long coast period (approximately 75 minutes) after the third stage separation. The damper package was evaluated and proven on a three-axis gas-bearing simulator that duplicated the LAGEOS spacecraft critical flight dynamics. In addition, a failure analysis of the damper assembly was performed. Performance of the damper during the LAGEOS flight has confirmed the preflight evaluation and analysis.

Abercrombie, R. A.↗
NASA NTRS1979

Performance of two-stage fan with a first-stage rotor redesigned to account for the presence of a part-span damper

The NASA two-stage fan was tested with a redesigned first-stage rotor. The redesign included a new design approach to account for the presence of a part-span damper. At design speed the fan achieved a peak efficiency of 0.803, which is 1.9 percentage points higher than the original design. The peak efficiencies of the first stage and first rotor were 0.789 and 0.821, respectively. An improvement in efficiency of up to 5 percentage points in the damper region was achieved over the original large damper version. The stall margin, based on flow conditions at peak efficiency, was 10 percent at design speed.

Gorrell, W. T.↗
NASA NTRS1979

An off-design correlation of part span damper losses through transonic axial fan rotors

The experimental performance of 10 transonic fan rotors was used to correlate losses caused by midchord part-span dampers (PSD) during off-design operation between 50 and 100 percent of design speed. The design tip speed for the rotors used varied from 419 to 425 m/s and the design pressure ratios from 1.6 to 2.0. The loss attributable to the damper and the region influenced along the blade height was correlated with relevant aerodynamic and geometric parameters. The losses at the design point were estimated by a previously reported correlation (Roberts, 1978). Using this as a base, the off-design losses were correlated with variation in blade suction surface incidence. A check with independent data showed that the prediction of damper losses and region of influence was fair to good for most of the off-design data examined.

Roberts, W. B.↗
NASA NTRS1980

Off-design correlation for losses due to part-span dampers on transonic rotors

Experimental data from 10 transonic fan rotors were used to correlate losses created by part-span dampers located near the midchord position on the rotor blades. The design tip speed of these rotors varied from 419 to 425 m/sec, and the design pressure ratio varied from 1.6 to 2.0. Additional loss caused by the dampers for operating conditions between 50 and 100 percent of design speed were correlated with relevant aerodynamic and geometric parameters. The resulting correlation predicts the variation of total-pressure-loss coefficient in the damper region to a good approximation.

Roberts, W. B.↗
NASA NTRS1980

Elastomer damper performance - A comparison with a squeeze film for a supercritical power transmission shaft

This paper describes the design and testing of an elastomer damper on a super-critical power transmission shaft. The elastomers were designed to provide acceptable operation through the fourth bending mode and to control synchronous as well as nonsynchronous vibration throughout the operating range. The design of the elastomer was such that it could be incorporated into the system as a replacement for a squeeze-film damper without a reassembly, which could have altered the imbalance of the shaft. This provided a direct comparison of the elastomer and squeeze-film dampers without having to assess the effect of shaft imbalance changes.

Zorzi, E. S.↗
NASA NTRS1981

Engine dynamic analysis with general nonlinear finite-element codes. I Overall approach and development of bearing damper element

NASA-sponsored research on engine dynamic simulation using general finite element nonlinear time transient computer codes available on the open market is reviewed. The approach taken was to develop software packages to model engine components which are not typically found on dynamical structures and are therefore not already computer codes. The software package developed for squeeze-film bearing dampers is outlined, and the results of a parametric study of damper pressure for a variety of specified circular orbits are presented for both long-bearing and short-bearing solutions. The data from a four-degree-of-freedom rotor-damper-stator model under conditions of small rotor unbalance through large rotor unbalance are also given.

Adams, M. L.↗
NASA NTRS1983

Coulomb Friction Damper

Standard hydraulic shock absorber modified to form coulomb (linear friction) damper. Device damps very small velocities and is well suited for use with large masses mounted on soft springs. Damping force is easily adjusted for different loads. Dampers are more reliable than fluid dampers and also more economical to build and to maintain.

Appleberry, W. T.↗
NASA NTRS1981

Analysis of high load dampers

High load damping requirements for modern jet engines are discussed. The design of damping systems which could satisfy these requirements is also discusseed. In order to evaluate high load damping requirements, engines in three major classes were studied; large transport engines, small general aviation engines, and military engines. Four damper concepts applicable to these engines were evaluated; multi-ring, cartridge, curved beam, and viscous/friction. The most promising damper concept was selected for each engine and performance was assessed relative to conventional dampers and in light of projected damping requirements for advanced jet engines.

Bhat, S. T.↗
NASA NTRS1983

The analysis and testing of blade platform friction dampers used in the high pressure fuel turbopump (HPFTP) of the Space Shuttle Main Engine (SSME)

Premature cracking of the first stage turbine blades in HPFTP of the SSME could be alleviated by redesign of the platform friction dampers that are used to reduce the vibration response of the blades. Analytical studies by the lumped mass method of friction damper effectiveness and spin pit tests of a straingaged bladed disk have been performed. Methodologies used in the program are described. Preliminary results show that the effectiveness of the blade platform dampers can be increased if the frequency and amplitude of the most damaging forcing functions can be defined.

Dominic, R. J.↗
NASA NTRS1981

Optimal damper location in the vibration control of large space structures

The problem of finding the optimal location of active dampers for the vibration control of space structures is investigated. The optimal location is where maximum damping can be introduced to a particular vibration mode. To this end, classical root locus techniques are used to study the effect on eigenvalues of placing a damper on an undamped structure. An efficient formulation is derived which avoids the solution of the damped eigenvalue problem. Based on the observation of the results for a free-free beam model, a Minimum Constrained Frequency Criterion (MCFC) for locating the optimal damper location is proposed.

Wang, B. P.↗
NASA NTRS1984

Digital control system for space structural dampers

A recently developed concept for a damper was improved by adding a small taper to the proof-mass, and using a proximeter to determine position. Also, an experimental damper was built using a three-inch stroke in place of the standard one-inch stroke. The analog controller initially used was replaced by an independent digital controller slaved to a TRS-80 Model I computer, which also serves as a highly effective, low-cost development system. An overall system concept for the use of proof-mass dampers is presented.

Haviland, J. K.↗
NASA NTRS1983

Forced response of a cantilever beam with a dry friction damper attached. I - Theory. II - Experiment

A theoretical and experimental study of the forced vibration response of a cantilevered beam with Coulomb damping nonlinearity is described. Viscous damping in the beam is neglected. Beam and dry friction damper configurations of interest for applications to turbine blade vibrations are considered. It is shown that the basic phenomena found by Dowell (1983) for a simply supported beam with an attached dry friction damper of specific geometry also apply to a cantilevered beam and a more general representation of the dry friction damper and its associated mass and stiffness.

Dowell, E. H.↗
NASA NTRS1987

Non-linear identification of a squeeze-film damper

Described is an experimental study to identify the damping laws associated with a squeeze-film vibration damper. This is achieved by using a non-linear filtering algorithm to process displacement responses of the damper ring to synchronous excitation and thus to estimate the parameters in an nth-power velocity model. The experimental facility is described in detail and a representative selection of results is included. The identified models are validated through the prediction of damper-ring orbits and comparison with observed responses.

Stanway, Roger↗
NASA NTRS1988

Electromagnetic dampers for cryogenic applications

Cryogenic turbomachinery of the type used to pump high-pressure liquid hydrogen at -423 F and liquid oxygen at -297 F to the main engines of the Space Shuttle are subjected to lateral rotor vibrations from unbalance forces and transient loads. Conventional dampers which utilize viscous fluids such as lubricating oil cannot be used in turbopumps because the bearing components are filled with either liquid hydrogen or liquid oxygen, which have viscosity comparable to air and, therefore, are not effective in viscous dampers. Electromagentic dampers are currently being explored as a means of providing damping in cryogenic turbopumps because their damping effectiveness increases as temperature decreases and because they are compatible with the liquid hydrogen or liquid oxygen in the turbopumps.

Brown, Gerald V.↗
NASA NTRS1987

An integrated approach for friction damper design

A procedure is outlined for determining the optimal design of friction dampers for high speed turbomachinery blading. The procedure includes: an integration of bench test results with finite element analysis and a single mode blade model to ensure accuracy of the analytical model and improve reliability of the friction damper design; an extension of the single mode blade model to predict the engine behavior of friction dampers; and a new way of viewing analytical and experimental results to determine optimal design parameters when the levels of excitation and damping in the system are unknown. Analysis and experiments are performed on a test disk in order to demonstrate and verify the accuracy of the design procedure.

Cameron, T. M.↗
NASA NTRS1988

Evaluation of a turbine blade damper using an integral approach

An integrated experimental/analytical approach to friction damper design optimization in cases where gas turbine blade-response data are unavailable under actual engine operating conditions is presently applied to the case of a damper designed to relieve a blade-cracking problem on a liquid fuel rocket engine's turbopump. Attention is given to the experimental methods and analytical models used, as well as to the predicted damper performance. The inclusion of macroslip, microslip, and variable normal load effects was found to be necessary.

Kielb, Robert E.↗
NASA NTRS1989

An electroviscous damper

A new type of vibration damper for rotor systems was developed and tested. The damper contains electroviscous fluid which solidifies and provides Coulomb damping when an electric voltage is imposed across the fluid. The damping capacity is controlled by the voltage. The damper was incorporated in a flexible rotor system and found to be able to damp out high levels of unbalanced excitation. Other proven advantages include controllability, simplicity, and no requirement for oil supply. Still unconfirmed are the capabilities to eliminate critical speeds and to suppress rotor instabilities.

Nikolajsen, Jorgen L.↗
NASA NTRS1988

Elasticity effects on cavitation in a squeeze film damper undergoing noncentered circular whirl

Elasticity of the liner and its effects on cavitation were numerically determined for a squeeze film damper subjected to dynamic loading. The loading was manifested as a prescribed motion of the rotor undergoing noncentered circular whirl. The boundary conditions were implemented using Elrod's algorithm which conserves lineal mass flux through the moving cavitation bubble as well as the oil film region of the damper. Computational movies were used to analyze the rapidly changing pressures and vapor bubble dynamics throughout the dynamic cycle for various flexibilities in the damper liner. The effects of liner elasticity on cavitation were only noticeable for the intermediate and high values of viscosity used in this study.

Brewe, David E.↗