Search NASA⌕ Search

SEARCH · Search NASA

Results for “Data Computing Interface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

CFD Models of a Serpentine Inlet, Fan, and Nozzle

Several computational fluid dynamics (CFD) codes were used to analyze the Versatile Integrated Inlet Propulsion Aerodynamics Rig (VIIPAR) located at NASA Glenn Research Center. The rig consists of a serpentine inlet, a rake assembly, inlet guide vanes, a 12-in. diameter tip-turbine driven fan stage, exit rakes or probes, and an exhaust nozzle with a translating centerbody. The analyses were done to develop computational capabilities for modeling inlet/fan interaction and to help interpret experimental data. Three-dimensional Reynolds averaged Navier-Stokes (RANS) calculations of the fan stage were used to predict the operating line of the stage, the effects of leakage from the turbine stream, and the effects of inlet guide vane (IGV) setting angle. Coupled axisymmetric calculations of a bellmouth, fan, and nozzle were used to develop techniques for coupling codes together and to investigate possible effects of the nozzle on the fan. RANS calculations of the serpentine inlet were coupled to Euler calculations of the fan to investigate the complete inlet/fan system. Computed wall static pressures along the inlet centerline agreed reasonably well with experimental data but computed total pressures at the aerodynamic interface plane (AIP) showed significant differences from the data. Inlet distortion was shown to reduce the fan corrected flow and pressure ratio, and was not completely eliminated by passage through the fan

Chima, R. V.↗
NASA NTRS1968

Digital-computer interface systems.

Digital computer interface systems design for simulation, control, instrumentation and data processing, discussing hybrid computer linkages

Korn, G. A.↗
NASA NTRS1976

General Purpose Computer (GPC) to GPC systems interface description

The General Purpose Computer (GPC) 'subsystem' of the Orbiter Data Processing System was described. Two interface areas are discussed. One is the area of GPC intraconnections and intracommunications involving the hardware/software interface between the Central Processing Unit (CPU) and the Input/Output Processor (IOP). The other is the area of GPC interconnections and intercommunications and involves the hardware/software interface between the five Orbiter GPC's. Based on the detailed GPC interface given, it is felt that the basic CPU to IOP interface and the GPC to GPC interface have the potential for trouble free operation. However, due to the complexity of the interface and the criticality of GPC synchronization to overall avionics performance, the GPC to GPC interface should be carefully evaluated when attempting to resolve test anomalies that may involve GPC timing and synchronization errors.

Breyer, B. C.↗
NASA NTRS2012

Lunar Reconnaissance Orbiter (LRO) Command and Data Handling Flight Electronics Subsystem

A document describes a high-performance, modular, and state-of-the-art Command and Data Handling (C&DH) system developed for use on the Lunar Reconnaissance Orbiter (LRO) mission. This system implements a complete hardware C&DH subsystem in a single chassis enclosure that includes a processor card, 48 Gbytes of solid-state recorder memory, data buses including MIL-STD-1553B, custom RS-422, SpaceWire, analog collection, switched power services, and interfaces to the Ka-Band and S-Band RF communications systems. The C&DH team capitalized on extensive experience with hardware and software with PCI bus design, SpaceWire networking, Actel FPGA design, digital flight design techniques, and the use of VxWorks for the real-time operating system. The resulting hardware architecture was implemented to meet the LRO mission requirements. The C&DH comprises an enclosure, a backplane, a low-voltage power converter, a single-board computer, a communications interface board, four data storage boards, a housekeeping and digital input/output board, and an analog data acquisition board. The interfaces between the C&DH and the instruments and avionics are connected through a SpaceWire network, a MIL-STD-1553 bus, and a combination of synchronous and asynchronous serial data transfers over RS-422 and LVDS (low-voltage differential-signaling) electrical interfaces. The C&DH acts as the spacecraft data system with an instrument data manager providing all software and internal bus scheduling, ingestion of science data, distribution of commands, and performing science operations in real time.

Nguyen, Quang↗
NASA NTRS1976

An interface between a datametrics 1085A manometer and a Hewlett-Packard 2100S computer

A hardware/software interface designed to mate a Datametrics models 1085A electronic manometer to a Hewlett-Packard (HP) model 2100S computer is described. The software driver operates in the basic control system (BCS) and requires 173 words of memory; the hardware interface uses an HP data source interface (DSI) card which requires one computer input/output channel. Results obtained by incorporating this interface into a data acquisition system indicate that the interface operates successfully.

Hillard, M. E., Jr.↗
NASA NTRS1995

A three-dimensional orthogonal laser velocimeter for the NASA Ames 7- by 10-foot wind tunnel

A three-component dual-beam laser-velocimeter system has been designed, fabricated, and implemented in the 7-by 10-Foot Wind Tunnel at NASA Ames Research Center. The instrument utilizes optical access from both sides and the top of the test section, and is configured for uncoupled orthogonal measurements of the three Cartesian coordinates of velocity. Bragg cell optics are used to provide fringe velocity bias. Modular system design provides great flexibility in the location of sending and receiving optics to adapt to specific experimental requirements. Near-focus Schmidt-Cassegrain optic modules may be positioned for collection of forward or backward scattered light over a large solid angle, and may be clustered to further increase collection solid angle. Multimode fiber optics transmit collected light to the photomultiplier tubes for processing. Counters are used to process the photomultiplier signals and transfer the processed data digitally via buffered interface controller to the host MS-DOS computer. Considerable data reduction and graphical display programming permit on-line control of data acquisition and evaluation of the incoming data. This paper describes this system in detail and presents sample data illustrating the system's capability.

Dunagan, Stephen E.↗
NASA NTRS1988

Wideband Digital Interface Unit

Signals converted from serial to parallel and buffered for input to computer. Wideband digital interface unit converts serial input data bits to 16-bit words and feeds them as needed to host computer.

Baltau, William M.↗
NASA NTRS1975

Low cost computer subsystem for the Solar Electric Propulsion Stage (SEPS)

The Solar Electric Propulsion Stage (SEPS) subsystem which consists of the computer, custom input/output (I/O) unit, and tape recorder for mass storage of telemetry data was studied. Computer software and interface requirements were developed along with computer and I/O unit design parameters. Redundancy implementation was emphasized. Reliability analysis was performed for the complete command computer sybsystem. A SEPS fault tolerant memory breadboard was constructed and its operation demonstrated.

Source record↗
NASA NTRS1979

ATLAS, an integrated structural analysis and design system. Volume 5: System demonstration problems

One of a series of documents describing the ATLAS System for structural analysis and design is presented. A set of problems is described that demonstrate the various analysis and design capabilities of the ATLAS System proper as well as capabilities available by means of interfaces with other computer programs. Input data and results for each demonstration problem are discussed. Results are compared to theoretical solutions or experimental data where possible. Listings of all input data are included.

Samuel, R. A.↗
NASA NTRS1981

Common data buffer

Time-shared interface speeds data processing in distributed computer network. Two-level high-speed scanning approach routes information to buffer, portion of which is reserved for series of "first-in, first-out" memory stacks. Buffer address structure and memory are protected from noise or failed components by error correcting code. System is applicable to any computer or processing language.

Byrne, F.↗
NASA NTRS1985

Space station data system analysis/architecture study. Task 2: Options development DR-5. Volume 1: Technology options

The second task in the Space Station Data System (SSDS) Analysis/Architecture Study is the development of an information base that will support the conduct of trade studies and provide sufficient data to make key design/programmatic decisions. This volume identifies the preferred options in the technology category and characterizes these options with respect to performance attributes, constraints, cost, and risk. The technology category includes advanced materials, processes, and techniques that can be used to enhance the implementation of SSDS design structures. The specific areas discussed are mass storage, including space and round on-line storage and off-line storage; man/machine interface; data processing hardware, including flight computers and advanced/fault tolerant computer architectures; and software, including data compression algorithms, on-board high level languages, and software tools. Also discussed are artificial intelligence applications and hard-wire communications.

Source record↗
NASA NTRS1987

Space shuttle main engine anomaly data and inductive knowledge based systems: Automated corporate expertise

Progress is reported on the development of SCOTTY, an expert knowledge-based system to automate the analysis procedure following test firings of the Space Shuttle Main Engine (SSME). The integration of a large-scale relational data base system, a computer graphics interface for experts and end-user engineers, potential extension of the system to flight engines, application of the system for training of newly-hired engineers, technology transfer to other engines, and the essential qualities of good software engineering practices for building expert knowledge-based systems are among the topics discussed.

Modesitt, Kenneth L.↗
NASA NTRS1991

Space shuttle Mission Control Center upgrade

The Mission Control Center (MCC) is the facility that provides centralization of all mission operations in support of the shuttle from liftoff through landing. This facility serves as the focal point for real time flight control operations supporting the shuttle, spacelab, and selected payload systems. MCC upgrade accomplishments are as follows: replaced 5 mainframe computers and the associated input/output data interfaces; developed and installed a distributed data system with 81 workstations, 5 LANs, data drivers, and a fiber optic distribution subsystem; developed over 1.5 million lines of code to support new distributed system; developed new digital voice system which provides the MCC capacity to handle th Shuttle programs demands and growth potential to handle Space Station; replaced failing digital TV equipment with digital generation equipment; replaced obsolete center screen projector; and provided the platform for the multiprogram control center.

Duffin, Pat↗
NASA NTRS2013

PhoneSat - The Smartphone Nanosatellite

PhoneSat 2.4, carried into space on November 19, 2013 aboard a Minotaur I rocket from the Mid-Atlantic Regional Spaceport at NASAs Wallops Flight Facility in Virginia, is the first of the PhoneSat family to use a two-way S-band radio to allow engineers to command the satellite from Earth. This mission also serves as a technology demonstration for a novel attitude determination and control system (ADCS) that establishes and stabilizes the satellites attitude relative to Earth. Unlike the earlier PhoneSats that used a Nexus One, PhoneSat 2.4 uses the Nexus S smartphone, which runs Googles Android operating system, and is made by Samsung Electronics Co., Suwon, So. Korea. The smartphone provides many of the functions needed by the satellite such as a central computer, data memory, ready-made interfaces for communications, navigation and power all pre-assembled in a rugged electronics package.

PhoneSat↗
NASA NTRS1994

Personal Computer Monitors Instrumentation Bus

IBM-compatible personal computer used instead of logic analyzer or other special instrument to monitor IEEE-488 interface data bus that interconnects various pieces of laboratory equipment. Needed is short program for computer, commercial general-purpose interface bus circuit card, and adapter cable to link card to bus. Software available in Ada or Quick Basic language.

Conroy, Bruce L.↗