Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design and modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Steady-state off-design modeling of the supercritical carbon dioxide recompression cycle for concentrating solar power applications with two-tank sensible-heat storage

Concentrating solar power researchers are evaluating the potential of the supercritical carbon dioxide recompression cycle to improve the thermal efficiency and decrease the capital costs of next-generation systems. This analysis investigates the steady-state off-design performance of a recompression cycle integrated with two-tank sensible-heat thermal energy storage as the ambient temperature and heat-transfer fluid (HTF) inlet conditions to the cycle change. This paper presents off-design component models and then cycle convergence and control models to maximize net cycle power output while constraining the high-side pressure and air-cooler fan power to their respective design values and fixing the cycle HTF outlet temperature to its design value. Results show that inventory control and air-cooler fan power are important control parameters that can be optimized to maximize off-design power output as the ambient temperature and HTF mass flow rate diverge from design. The high-side pressure and fan power constraints cause the cycle net power to degrade when the ambient temperature is warmer than the design value, and this study calculates a maximum mass flow rate for hot days above which the cycle cannot achieve the design HTF outlet temperature. Finally, the analysis shows that optimizing compressor shaft speeds can improve cold-day performance by around 1.5 percentage points and part-load performance by up to 2.5 percentage points versus a baseline case with no active compressor control.

14 SOLAR ENERGY↗
DOE OSTI2024

The Case for Co-Designing Model Architectures with Hardware

While GPUs are responsible for training the vast majority of state-of-the-art deep learning models, the implications of their architecture are often overlooked when designing new deep learning (DL) models. As a consequence, modifying a DL model to be more amenable to the target hardware can significantly improve the runtime performance of DL training and inference. In this paper, we provide a set of guidelines for users to maximize the runtime performance of their transformer models. These guidelines have been created by carefully considering the impact of various model hyperparameters controlling model shape on the efficiency of the underlying computation kernels executed on the GPU. We find the throughput of models with “efficient” model shapes is up to 39% higher while preserving accuracy compared to models with a similar number of parameters but with unoptimized shapes.

Yin, Junqi↗
DOE OSTI2023

Design, Modeling, and Testing of a Novel Inductor for Electric Vehicles: Iron Nitride Soft Magnetic Composites

New technology for electric vehicles (EVs) must meet the requirements of higher energy usage, lower costs, and more sustainable source materials. One promising material for EV power system components is iron nitride (IN) soft magnetic composites (SMCs) because of their competitive magnetic properties and high abundance of the source materials. As part of an ongoing program at Sandia National Laboratories, this project focused on using computer modeling to optimize the prototyping process for an iron nitride SMC toroidal inductor to reach a target inductance of 600 μH. Four inductors with different combinations of wiring (26 AWG and 20 AWG) and vol% loading of iron nitride (65 vol% and 50 vol%) were fabricated at Cal Poly and characterized using an LCR meter. These inductors were also modeled using COMSOL Multiphysics™ with the Magnetic Fields module. The inductance data from the experiment and the model show that the 65 vol% IN prototypes and models agree with about 8% difference, while the 50 vol% IN samples show about a 9% difference between the prototype and the model. These results suggest that the model can predict inductance with both accuracy and precision with low confidence for the given sample size of four. An additional parameter of AC resistance is studied but the AC resistance results from the inductors and from the model generally do not agree closely, suggesting that the current model used in the project does not fully capture the mechanisms behind AC resistance of the inductor. With the focus of the project on inductance, the percent difference results of less than 9% across the four inductors that were tested increases confidence in the model’s predictive capabilities for inductance only. Using the inductance results from both the model and experiment, the final suggested inductor design is a 65 vol% core with 150 windings of 20 AWG wire that is 8 cm across and 1.5 cm tall to reach the inductance goal of 600 μH based on analysis using the optimized COMSOLTM model.

33 ADVANCED PROPULSION SYSTEMS↗
NASA NTRS1992

Analysis of the lettuce data from the variable pressure growth chamber at NASA Johnson Space Center: A three-stage nested design model

A model of three-stage nested experimental design was applied to analyze the lettuce data obtained from the variable pressure growth chamber test bed at NASA-Johnson Space Center. From the results of an application of the analysis of variance and covariance on the data set, it was noted that all of the (uncontrollable) factors, Side, Zone, Height and (controllable) PAR (photosynthetically active radiation), had nonhomogeneous effects on the dry weight of the edible biomass of lettuce per pot. Incidentally, the variations accountable to the (uncontrollable) factorial heterogeneities are merely 9 percent and 17 percent of the total variation for both the first and second crop test, respectively. After adjusting for the PAR as a covariate in the no-intercept model, the accountable variations to all the four factors are 94 percent and 92 percent for the first and the second crop test, respectively. With the use of a no-intercept simple linear regression model, the accountable variations to the factor PAR are 92 percent and 90 percent for the first and the second crop test, respectively. Evidently, the (controllable) factor PAR is the dominating one.

Lee, Tze-San↗
NASA NTRS1972

Preliminary shuttle structural dynamics modeling design study

The design and development of a structural dynamics model of the space shuttle are discussed. The model provides for early study of structural dynamics problems, permits evaluation of the accuracy of the structural and hydroelastic analysis methods used on test vehicles, and provides for efficiently evaluating potential cost savings in structural dynamic testing techniques. The discussion is developed around the modes in which major input forces and responses occur and the significant structural details in these modes.

Source record↗
NASA NTRS1984

A global low order spectral model designed for climate sensitivity studies

A two level, global, spectral model using pressure as a vertical coordinate is developed. The system of equations describing the model is nonlinear and quasi-geostrophic. A moisture budget is calculated in the lower layer only with moist convective adjustment between the two layers. The mechanical forcing of topography is introduced as a lower boundary vertical velocity. Solar forcing is specified assuming a daily mean zenith angle. On land and sea ice surfaces a steady state thermal energy equation is solved to calculate the surface temperature. Over the oceans the sea surface temperatures are prescribed from the climatological average of January. The model is integrated to simulate the January climate.

Hanna, A. F.↗
DOE OSTI2023

Design, modeling and simulation of nuclear-powered integrated energy systems with cascaded heating applications

Nuclear-renewable integrated energy systems (IES) consist of a variety of energy generation and conversion technologies and can be used to meet heterogeneous end uses (e.g., electricity, heat, and cooling demands). In addition to supply-demand balance, end-use heat demands usually require heat supply of certain temperature ranges. The effective and efficient utilization of heat produced within an IES is, therefore, a critical challenge. Here, this paper examines design options of an IES that includes heating processes of multiple temperature grades. We investigate a cascaded design configuration, where the remaining residual heat after high-grade heating processes [e.g., hydrogen production through high-temperature steam electrolysis (HTSE)] is recovered to meet the low-grade heating needs [e.g., district heating (DH)]. Additionally, a thermal energy storage system is integrated into the DH system to address the imbalance between heat supply and demand. This paper primarily focuses on the design and modeling of the proposed system and evaluates its operation with a 24-h transient process simulation using a DH demand profile with hourly resolution. The results indicate that the residual heat from the HTSE exhaust is insufficient for the DH demand, and additional topping heat directly from the reactor process steam is needed. Furthermore, the inclusion of thermal energy storage within the DH system provides the necessary balance between thermal generation and demand, thereby ensuring a consistent rated temperature of the DH supply water. This approach helps minimize the control actions needed on the reactor side.

08 HYDROGEN↗
NASA NTRS2016

Magnetic Shield Design Modeling and Validation for SWOT Spacecraft Ka-Band Extended Interaction Klystron

Two Extended Interaction Klystrons (EIKs) containing strong permanent magnets were modeled magnetically in a representative spacecraft geometry using commercial finite element modeling techniques and were validated against measurements made at varying distances. Initial modeling results for the 63 A-m2 dipole moment magnets showed that magnetic shields would be necessary in order to meet magnetic field requirements for the Surface Water and Ocean Topography (SWOT) spacecraft, which contains components that are susceptible to external DC magnetic fields. JPL and the EIK vendor proposed cold rolled steel and mu-metal as potential shield materials along with proposed thicknesses of 0.5 mm and 1.5 mm. Magnetic shields made from each of these materials were designed and modeled in software, taking highfield saturation into account. Prototype magnetic shields with these parameters were then built, measured with an existing EIK, and compared against modeling results. For single-axis field measurements along the dipole axis, modeling results were within 7 gauss of the measured values at 10 cm from the magnet, and converged to less than 1.5 gauss at distances greater than 14 cm from the magnet. Three-axis field measurements at locations of interest showed that model correlation improved to within 4 gauss at 11 cm and 2 gauss for distances ranging between 15 cm and 36 cm.

Gonzales, Edward↗
NASA NTRS2016

Magnetic Shield Design Modeling and Validation for SWOT Spacecraft Ka-Band Extended Interaction Klystron

Two Extended Interaction Klystrons (EIKs) containing strong permanent magnets were modeled magnetically in a representative spacecraft geometry using commercial finite element modeling techniques and were validated against measurements made at varying distances. Initial modeling results for the 63 A-m2 (amperes per square meter) dipole moment magnets showed that magnetic shields would be necessary in order to meet magnetic field requirements for the Surface Water and Ocean Topography (SWOT) spacecraft, which contains components that are susceptible to external DC (Direct Current) magnetic fields. JPL (Jet Propulsion Laboratory) and the EIK vendor proposed cold rolled steel and mu-metal as potential shield materials along with proposed thicknesses of 0.5 millimeters and 1.5 millimeters. Magnetic shields made from each of these materials were designed and modeled in software, taking high-field saturation into account. Prototype magnetic shields with these parameters were then built, measured with an existing EIK, and compared against modeling results. For single-axis field measurements along the dipole axis, modeling results were within 7 gauss of the measured values at 10 centimeters from the magnet, and converged to less than 1.5 gauss at distances greater than 14 centimeters from the magnet. Three-axis field measurements at locations of interest showed that model correlation improved to within 4 gauss at 11 centimeters and 2 gauss for distances ranging between 15 centimeters and 36 centimeters.

Gonzales, Edward↗
NASA NTRS1992

Modeling, design, fabrication, and testing of InP Gunn devices in the D-band (110 GHz - 170 GHz)

The development of fundamental Gunn sources for D-band frequencies requires improvements of doping profiles, processing technology, and circuit design. We have developed a technology for fabricating InP Gunn diodes using an InGaAs etch-stop layer between the InP substrate and the device layers. The epitaxial layers were grown by CBE. During device processing, the substrate is completely removed. Substrateless devices with an n(+) InGaAs cap layer are expected to have reduced contact and series resistances, and skin effect losses. This technology gives better uniformity and control of the device geometry across the processed chip. InP Gunn devices with a 1.7 micron long active region (doping : 9 x 10(exp 15) cm(exp -3)) have been mounted on copper heat sinks. Two tapered leads were then bonded to the diode and to four quartz standoffs. As a preliminary result, an output power of 13 mW at 82 GHz was obtained. Based on these RF measurements, we determine appropriate material parameters to be used in the Ensemble Monte Carlo model. Subsequently, we use this model to design and evaluate the performance of InP Gunn Devices for D-band frequencies. Using the same technology, we are currently processing Gunn devices with a 1 micron long active region for operation at higher frequencies.

Kamoua, R.↗
NASA NTRS2000

Design Models for the Development of Helium-Carbon Sorption Crycoolers

We have developed models for predicting the performance of helium-based Joule-Thomson continuous-flow cryocoolers using charcoal-pumped sorption compressors. The models take as inputs the number of compressors, desired heat-lift, cold tip temperature, and available precooling temperature and provide design parameters as outputs. Future laboratory development will be used to verify and improve the models. We will present a preliminary design for a two-stage vibration-free cryocooler that is being proposed as part of a mid-infrared camera on NASA's Next Generation Space Telescope. Model predictions show that a 10 mW helium-carbon cryocooler with a base temperature of 5.5 K will reject less than 650 mW at 18 K. The total input power to the helium-carbon stage is 650 mW. These models, which run in MathCad and Microsoft Excel, can be coupled to similar models for hydrogen sorption coolers to give designs for 2-stage vibration-free cryocoolers that provide cooling from approx. 50 K to 4 K.

Lindensmith, C. A.↗
NASA NTRS2000

Design Models for the Development of Helium-Carbon Sorption Cryocoolers

We have developed models for predicting the performance of helium-based Joule-Thomson continuous-flow cryocoolers using charcoal-pumped sorption compressors. The models take as inputs the number of compressors, desired heat-lift, cold tip temperature, and available precooling temperature and provide design parameters as outputs. Future laboratory development will be used to verify and improve the models. We will present a preliminary design for a two-stage vibration-free cryocooler that is being proposed as part of a mid-infrared camera on NASA's Next Generation Space Telescope. Model predictions show that a 10 mW helium-carbon cryocooler with a base temperature of 5.5 K will reject less than 650 mW at 18 K. The total input power to the helium-carbon stage is 650 mW. These models, which run in MathCad and Microsoft Excel, can be coupled to similar models for hydrogen sorption coolers to give designs for 2-stage vibration-free cryocoolers that provide cooling from approximately 50 K to 4 K.

Lindensmith, Chris A.↗
NASA NTRS1982

SOYCHMBR.I - A model designed for the study of plant growth in a closed chamber

The analytical model SOYCHMBER.I, an update and alteration of the SOYMOD/OARDC model, for describing the total processes experienced by a plant in a controlled mass environment is outlined. The model is intended for use with growth chambers for examining plant growth in a completely controlled environment, leading toward a data base for the design of spacecraft food supply systems. SOYCHMBER.I accounts for the assimilation, respiration, and partitioning of photosynthate and nitrogen compounds among leaves, stems, roots, and potentially, flowers of the soybean plant. The derivation of the governing equations is traced, and the results of the prediction of CO2 dynamics for a seven day experiment with rice in a closed chamber are reported, together with data from three model runs for soybean. It is concluded that the model needs expansion to account for factors such as relative humidity.

Reinhold, C.↗
NASA NTRS1980

Model design and instrumentation experiences with continuous-flow cryogenic tunnels

The development of wind tunnels that can be operated at cryogenic temperatures has placed several new demands on the ability to build and instrument wind tunnel models. The experiences at the NASA Langley Research Center relative to the design and instrumentation of models for continuous flow cryogenic wind tunnels are reviewed.

Kilgore, R. A.↗
NASA NTRS1993

Civil tiltrotor transport point design: Model 940A

The objective of this effort is to produce a vehicle layout for the civil tiltrotor wing and center fuselage in sufficient detail to obtain aerodynamic and inertia loads for determining member sizing. This report addresses the parametric configuration and loads definition for a 40 passenger civil tilt rotor transport. A preliminary (point) design is developed for the tiltrotor wing box and center fuselage. This summary report provides all design details used in the pre-design; provides adequate detail to allow a preliminary design finite element model to be developed; and contains guidelines for dynamic constraints.

Rogers, Charles↗
DOE OSTI2021

Design, modeling and experimental validation of a micro cantilever beam with an electro-controllable twisting ability

The structure design of micro cantilever beams (MCBs), which has a significant effect on MCBs' controllable actuation range, is usually restricted by the establishment of the inner electric circuit. This paper proposes the design of a micro electro-controllable twisting cantilever beam (METCB). The architecture and the fabrication diagram of the proposed METCB are presented before its features are theoretically and experimentally validated. In detail, the analytical validation includes a sequence of two models: electro-thermal and thermo-mechanical. Through these two models, the thermal distribution along the METCB and the deformation brought by the thermal distribution are investigated, respectively. On the basis of the design and equations, the METCB samples have been manufactured using a planar deposition technique with an e-beam evaporator. Two in-site experiments are then conducted to sequentially figure out the upper voltage limit of the inner electric circuit and the maximum temperature limit of the METCB. Finally, another experiment is carried out to explore the relation between the applied voltage and the relative twisting angle of the METCB sample. Here, the theoretical prediction and the observed experiment result both prove the feasibility of the proposed METCB and its electro-controllable twisting ability.

36 MATERIALS SCIENCE↗