Search NASA⌕ Search

SEARCH · Search NASA

Results for “Edge localized modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

71 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Analysis of Composite Skin-Stiffener Debond Specimens Using Volume Elements and a Shell/3D Modeling Technique

The debonding of a skin/stringer specimen subjected to tension was studied using three-dimensional volume element modeling and computational fracture mechanics. Mixed mode strain energy release rates were calculated from finite element results using the virtual crack closure technique. The simulations revealed an increase in total energy release rate in the immediate vicinity of the free edges of the specimen. Correlation of the computed mixed-mode strain energy release rates along the delamination front contour with a two-dimensional mixed-mode interlaminar fracture criterion suggested that in spite of peak total energy release rates at the free edge the delamination would not advance at the edges first. The qualitative prediction of the shape of the delamination front was confirmed by X-ray photographs of a specimen taken during testing. The good correlation between prediction based on analysis and experiment demonstrated the efficiency of a mixed-mode failure analysis for the investigation of skin/stiffener separation due to delamination in the adherents. The application of a shell/3D modeling technique for the simulation of skin/stringer debond in a specimen subjected to three-point bending is also demonstrated. The global structure was modeled with shell elements. A local three-dimensional model, extending to about three specimen thicknesses on either side of the delamination front was used to capture the details of the damaged section. Computed total strain energy release rates and mixed-mode ratios obtained from shell/3D simulations were in good agreement with results obtained from full solid models. The good correlations of the results demonstrated the effectiveness of the shell/3D modeling technique for the investigation of skin/stiffener separation due to delamination in the adherents.

Krueger, Ronald↗
NASA NTRSDate not supplied

Deep Learning-Based Negotiation Strategy Selection for Cooperative Conflict Resolution in Urban Air Mobility

This paper presents a collaborative conflict resolution technique using deep neural network-based intelligent search of the solution space. This approach offers a rapid convergence to a mutually acceptable solution for real-time conflict resolution, suitable for urban air mobility operations. Furthermore, the presented technique allows operational flexibility to the urban air mobility agents where these agents can collaboratively devise the solution via integrative negotiation, based on their local utility functions, as long as such a solution does not violate the global safety thresholds. The presented machine-to-machine negotiation method is built on our prior work on holistic assessment of the airspace and potential conflict detection implemented at-the-edge, onboard the unmanned aircraft systems. This paper extends the prior work to augment decision-making at-the-edge, thereby, promising a true distributed control architecture for urban air mobility. In this approach, each agent (a) builds a potential in-flight conflict map, (b) identifies the conflicting agents, (c) dynamically prepares a list of alternatives based on its current utility functions, (d) negotiates with the conflicting agents to pick one of these alternatives, and (e) implements the negotiated alternative to mutually resolve the conflict. Note that such an approach does not require a contingency plan to be made pre-flight, as the conflict resolution strategies are decided and negotiated in real time based on the present state of the agent. The contingency plan, if available, can serve as an input to the real-time conflict resolution strategy formulation, and also can be used as a fallback plan in case the negotiation fails and the impacted agents need to switch to a rule-based/supervisory resolution mode from the discussed distributed resolution mode. The presented collaborative negotiation-based conflict resolution technique incorporates a time-dependent reward function to catalyze collaborative resolution by incentivizing the agents with local and global rewards beneficial to their business operations.

Advanced Air Mobility↗
NASA NTRS1995

An intercomparison of plasma turbulence at three comets: Grigg-Skjellerup, Giacobini-Zinner, and Halley

We examine and intercompare the LF plasma wave turbulence at three comets: Grigg-Skjellerup (GS), Giacobini-Zinner (GZ), and Halley (H). All three have power spectral peaks at the local ion cyclotron frequency (the pump wave) at approx. 10(exp -2) Hz, and a power-law fall-off at higher frequencies that suggest the development of turbulent cascades. The power laws for the three comets are approximately f(exp -1.9), f(exp -1.9) and f(exp -2.1), respectively. However, other than the similarities in the power spectra, we find the magnetic field turbulence is considerably different at the three comets. Phase steepening is demonstrated to occur at the trailing edges of the GS waves. This is probably due to nonlinear steepening plus dispersion of the left-hand mode components. A coherency analysis of GZ turbulence indicates that it is primarily composed of righthanded mode components, i.e., the turbulence is 'whistlermode.' This too can be explained by nonlinear steepening plus dispersion of the magnetosonic waves. At the level of GS and GZ turbulence development when the spacecraft measurements were made, classical three-wave processes, such as the decay or modulation instabilities do not appear to play important roles. It is most likely that the nonlinear steepening and dispersive time scales are more rapid than three-wave processes, and the latter had not had time to develop for the relatively 'new' turbulence. The wave turbulence at Halley is linearly polarized. The exact nature of this turbulence is still not well understood at this time. Several possibilities are suggested, based on our preliminary analyses.

Tsurutani, Bruce T.↗
NASA NTRS2009

Characterization of Damage in Triaxial Braid Composites Under Tensile Loading

Carbon fiber composites utilizing flattened, large tow yarns in woven or braided forms are being used in many aerospace applications. Their complex fiber architecture and large unit cell size present challenges in both understanding deformation processes and measuring reliable material properties. This report examines composites made using flattened 12k and 24k standard modulus carbon fiber yarns in a 0 /+60 /-60 triaxial braid architecture. Standard straight-sided tensile coupons are tested with the 0 axial braid fibers either parallel with or perpendicular to the applied tensile load (axial or transverse tensile test, respectively). Nonuniform surface strain resulting from the triaxial braid architecture is examined using photogrammetry. Local regions of high strain concentration are examined to identify where failure initiates and to determine the local strain at the time of initiation. Splitting within fiber bundles is the first failure mode observed at low to intermediate strains. For axial tensile tests splitting is primarily in the 60 bias fibers, which were oriented 60 to the applied load. At higher strains, out-of-plane deformation associated with localized delamination between fiber bundles or damage within fiber bundles is observed. For transverse tensile tests, the splitting is primarily in the 0 axial fibers, which were oriented transverse to the applied load. The initiation and accumulation of local damage causes the global transverse stress-strain curves to become nonlinear and causes failure to occur at a reduced ultimate strain. Extensive delamination at the specimen edges is also observed.

Littell, Justin D.↗
NASA NTRS1993

On the instability of flow in a streamwise corner

The linear stability of an incompressible laminar flow in the blending boundary layer between the boundary layer in a 90 deg streamwise corner and a Blasius boundary layer well away from the corner is examined using a locally parallel flow approximation. It is shown that the influence of the outer boundary conditions associated with oblique modes of disturbances which are anti-symmetric about the bisector plane have a profound effect on the stability of the flow. As a result, in good agreement with observation, the critical streamwise Reynolds number, associated with a spanwise location is significantly reduced as the corner is approached, being R(sub Cr) = 60 approximately for spanwise distance of z* = 6x*R(sup -1) from the corner compared with R(sub Cr) = 322 approximately for z* = 20x*R(sup -1), where x* measures downstream distance from the leading edges. At R = 600, the growth rate of the most amplified mode of disturbance at the former location is over six times greater than that at the latter; the corresponding wave angle at the two locations is respectively 44 deg and 5 deg, approximately.

Dhanak, Manhar R.↗
NASA NTRS1983

Stagnation region gas film cooling: Effects of dimensionless coolant temperature

An experimental investigation was conducted to mode the film cooling performance for a turbine vane leading edge using the stagnation region of a cylinder in cross flow. Experiments were conducted with a single row of spanwise angled (25 deg) coolant holes for a range of the coolant blowing ratio and dimensionless coolant temperature with free stream-to-wall temperature ratio approximately 1.7 and Re sub D = 90000. the cylindrical test surface was instrumented with miniature heat flux gages and wall thermocouples to determine the percentage reduction in the Stanton number as a function of the distance downstream from injection (x/d sub 0) and the location between adjacent holes (z/S). Data from local heat flux measurements are presented for injection from a single row located at 5 deg, 22.9 deg, 40.8 deg, from stagnation using a hole spacing ratio of S/d = 5. The film coolant was injected with T sub c T sub w with a dimensionless coolant temperature in the range 1.18 or equal to theta sub c or equal to 1.56. The data for local Stanton Number Reduction (SNR) showed a significant increase in SNR as theta sub c was increased above 1.0.

Bonnice, M. A.↗
NASA NTRS1994

Spatial distribution of plasma wave activity in the nightside ionosphere of Venus

In this study we use 14 years of Pioneer Venus Orbiter Electric Field Detector (OEFD) data to define the characteristics of (VLF) burst activity in the nightside ionosphere of Venus. Our statistical results show that there are essentially four types of VLF signals. The first type of signal is only observed in the 100 Hz channel and not in any of the higher frequency channels (730 Hz, 5.4 kHz or 30 kHz). Occurrence of these waves is controlled by the magnetic field with a weaker dependence on electron density. The occurrence of these waves is controlled by the magnetic field with a weaker dependence on electron density. The occurrence rate decreases with increasing altitude to a height of 600 km. For higher altitudes beyond 600 km the occurrence rate remains roughly constant. The statistics of these signals are what one would expect for whistler mode waves from a subionospheric source. The second type of signal is broadline wave activity appearing below 300 km in the low altitude ionosphere. These signals often occur in all four channels of the OEFD. These signals are also thought to come from a subionospheric source. The third type of signal appearing near the edge of the planetary optical shadow. They are probably ion acoustic waves generated by a current driven instability associated with plasma clouds in the wake. The fourth type of signal is a narrow band wave. It occurs in either of the two high frequency channels in the high altitude tail region, and is attributed to locally generated Langmuir waves. In addition, we also observe spacecraft interference noise in both the 100 and 730 Hz channels. These signals mainly occur near the edge of the planetary optical shadow and have an inbound and outbound asymmetry in activity.

Ho, C.-M.↗
NASA NTRS1977

Preliminary development of a fundamental analysis model for crack growth in a fiber reinforced composite material

A mathematical model for the strength of fiber reinforced composites containing specific flaws is described. The approach is to embed a local heterogeneous region surrounding the crack tip in an anisotropic elastic continuum. By consideration of the individual failure events activated near the flaw tip, a strength prediction can be made from basic properties of the composite constituents. Computations for arbitrary flaw size and orientation have been performed for unidirectional composites with linear elastic-brittle constituent behavior. The mechanical properties were those of graphite epoxy. With the rupture properties arbitrarily varied to test the capability of the model to reflect real fracture modes in fiber composites, it is shown that fiber breakage, matrix crazing, crack bridging, matrix-fiber debonding, and axial splitting all can occur during gradually increasing load prior to catastrophic fracture. Qualitative comparisons with experimental results on edge-notched unidirectional graphite epoxy specimens have also been made.

Kanninen, M. F.↗
NASA NTRS1989

Experimental observations and finite element analysis of the initiation of fiber microbuckling in notched composite laminates

An understanding was developed of the factors that determine the semi-circular edge-notched compressive strength and the associated failure mode(s) were identified of thermoplastic composite laminates with multidirectional stacking sequences. The experimental observations and the detailed literature review suggest at least four factors that affected the determination of the strain levels at which fiber microbuckling initiates and thus, partially control the composite's compression strength. The dependent variables studied are the compressive strength of a reduced gage section compression specimen and the compression strength of a compression specimen with two semi-circular edge notches (no opposite free edges) centered along the gage section. In this research, specimens containing two semi-circular edge notches (no opposite free edges) were loaded in compression at a relatively slow rate to provide more stable development of fiber microbuckling damage. The results indicate that the local constraints (free surfaces, supporting ply orientation, and resin-rich regions) significantly affect the strain level for the initiation of in-plane fiber microbuckling. Preliminary results at an elevated temperature, 77 C, showed the shear stress yield strength of the resin was reduced and consequently, the resistance to fiber microbuckling was also reduced. The finite element analysis of the perfectly straight fiber problem indicates that the free surface effect causes a 10 percent reduction in the critical buckling strain. However, the experimentally measured reduction for fibers with an initial fiber curvature, was 35 percent.

Guynn, E. Gail↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbomachinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbopumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbomachinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test article is a low aspect ratio cantilevered plate, thus mimicing a single inducer blade that is unwrapped from its hub. The test article is oriented at zero angle of attack and has a triangular trip at its leading edge to induce cavitation. To change the extent of cavitation, the static pressure of the water tunnel is controlled. A high-speed camera is used to quantify the coverage of the cavitation sheet.

Fluid-Structure Interaction↗
NASA NTRS1980

Experimental investigation of graphite/polyimide sandwich panels in edgewise compression

The local and general buckling behavior of graphite/polyimide sandwich panels simply supported along all four edges and loaded in uniaxial edgewise compression was investigated. Material properties of adhesive and facings were determined from flatwise tension and sandwich beam flexure tests. Tensile and compressive material properties of the facings were determined at 116, R.T., and 589 K (-250, R.T., and 600 F) using the sandwich beam flexure test method. Results indicate that Gr/PI is a usable structural material for short term use at temperatures as high as 589 K (600 F). Buckling specimens were 30.5 X 33.0 cm (12 x 13 in.), had quasi-isotropic symmetric facings and a glass/polyimide honeycomb core. Core thicknesses varied and three panels of each thickness were tested in edgewise compression at room temperature to investigate failure modes and corresponding buckling formulas. Specimens 0.635 cm (0.25 in.) thick failed by overall buckling at loads close to the analytically predicted buckling load; all other panels failed by face wrinkling. Results of the winkling tests indicate that several buckling formulas were unconservative and therefore not suitable for design purposes; recommended wrinkling equations are presented.

Camarda, C. J.↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbo machinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbo pumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbo machinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test article is a low aspect ratio cantilevered plate, thus mimicing a single inducer blade that is unwrapped from its hub. The test article is oriented at zero angle of attack and has a triangular trip at its leading edge to induce cavitation. To change the extent of cavitation, the static pressure of the water tunnel is controlled. A high-speed camera is used to quantify the coverage of the cavitation sheet.

Structural Dynamics↗
NASA NTRS1989

Application of unstructured grid methods to steady and unsteady aerodynamic problems

The purpose is to describe the development of unstructured grid methods which have several advantages when compared to methods which make use of structured grids. Unstructured grids, for example, easily allow the treatment of complex geometries, allow for general mesh movement for realistic motions and structural deformations of complete aircraft configurations which is important for aeroelastic analysis, and enable adaptive mesh refinement to more accurately resolve the physics of the flow. Steady Euler calculations for a supersonic fighter configuration to demonstrate the complex geometry capability; unsteady Euler calculations for the supersonic fighter undergoing harmonic oscillations in a complete-vehicle bending mode to demonstrate the general mesh movement capability; and vortex-dominated conical-flow calculations for highly-swept delta wings to demonstrate the adaptive mesh refinement capability are discussed. The basic solution algorithm is a multi-stage Runge-Kutta time-stepping scheme with a finite-volume spatial discretization based on an unstructured grid of triangles in 2D or tetrahedra in 3D. The moving mesh capability is a general procedure which models each edge of each triangle (2D) or tetrahedra (3D) with a spring. The resulting static equilibrium equations which result from a summation of forces are then used to move the mesh to allow it to continuously conform to the instantaneous position or shape of the aircraft. The adaptive mesh refinement procedure enriches the unstructured mesh locally to more accurately resolve the vortical flow features. These capabilities are described in detail along with representative results which demonstrate several advantages of unstructured grid methods. The applicability of the unstructured grid methodology to steady and unsteady aerodynamic problems and directions for future work are discussed.

Batina, John T.↗
NASA NTRSDate not supplied

Cavitation Effects on the Structural Dynamics of Turbomachinery Components

The structural integrity of inducer and impeller blades in rocket engine turbomachinery must be evaluated in the face of complex excitation mechanisms including fluctuating pressures due to cavitation. Cavitation occurs when the local fluid pressure drops below the vapor pressure, causing the formation of vapor-filled bubbles. Cavitation can exist to various extents within the typical operating range of rocket engine turbopumps. Despite recent progress towards reducing uncertainties in structural dynamic models of turbomachinery components, the extent to which pump cavitation affects the structural dynamic properties (i.e., natural frequencies, damping, and mode shapes) of inducer and impeller blades remains largely unknown. To study the structural dynamic effects of cavitating flows, experiments are conducted in a high-speed water tunnel. The test articles mimic a single inducer blade that is unwrapped from the hub, thus resembling a low aspect ratio cantilevered plate. To induce cavitation, the plates are oriented at a non-zero angle of attack and have rough strips near their leading edges. To control the extent of cavitation, the static pressure of the water tunnel is controlled between roughly 0.5 and 1.5 atm. A high-speed camera is used to quantify the coverage of the cavitations heet. The sheet coverage is then correlated to changes in fluid-added mass and hydroelstic damping. In addition, a corresponding two-way coupled CFD/FE model is under development for test/analysis correlation.

Ben Davis↗
NASA NTRS1986

Wave speeds in the corona and the dynamics of mass ejections

A disturbance or coronal mass ejection being advected by the solar wind will expand at the fastest local characteristic speed - typically approximately the fast-mode speed. To estimate this characteristic wave speed and the velocity field in the ambient corona, it is necessary to know the magnetic field, temperature, and density. Only the density is known from coronal observations. The temperature, magnetic field, and velocity are not yet directly measured in the outer corona and must be estimated from a model. In this study, it is estimated that the magnetic field, solar wind velocity, and characteristic speeds use the MHD model of coronal expansion between 1 and 5 solar radii (R solar radii) with a dipole magnetic field at the base. This model, for a field strength of about 2 gauss at the base, gives flow speeds at low latitudes (near the heliospheric current sheet) of 250 km/s at 5 R solar radii and, 50 km/s at 2 solar radii, and fast-mode speeds to 400 to 500 km/s everywhere between 2 and 5 solar radii. This suggests that the outer edge of a velocity of mass ejection reported by MacQueen and Fisher (1983) and implies that the acceleration mechanism for coronal mass ejections is other than simple entrainment in the solar wind.

Suess, S. T.↗
NASA NTRS1999

Mars Global Surveyor Thermal Emission Spectrometer (TES) Observations of Dust Opacity During Aerobraking and Science Phasing

The Mars Global Surveyor (MGS) arrived at Mars in September 1997 near Mars southern spring equinox and has now provided monitoring of conditions in the Mars atmosphere for more than half a Mars year. The large majority of the spectra taken by the Thermal Emission Spectrometer (TES) are in a nadir geometry (downward looking mode) where Mars is observed through the atmosphere. Most of these contain the distinct spectral signature of atmospheric dust. For these nadir-geometry spectra we retrieve column-integrated infrared aerosol (dust) opacities. TES observations during the aerobraking and science-phasing portions of the MGS mission cover the seasonal range L(sub s)=184 deg - 28 deg. Excellent spatial coverage was obtained in the southern hemisphere. Northern hemisphere coverage is generally limited to narrow strips taken during the periapsis pass but is still very valuable. At the beginning of the mission the 9-(micron)meter dust opacity at midsouthern latitudes was low (0.15-0.25). As the season advanced through southern spring and into summer, TES observed several regional dust storms (including the Noachis dust storm of November 1997) where peak 9-(micron)meter dust opacities approached or exceeded unity, as well as numerous smaller local storms. Both large and small dust storms exhibited significant changes in both spatial coverage and intensity over a timescale of a day. Throughout southern spring and summer the region at the edge of the retreating southern seasonal polar ice cap was observed to be consistently more dusty than other latitudes.

Smith, Michael D.↗
NASA NTRS1998

Trends in Antarctic Surface Temperatures and Ice Extent from Satellite and Surface Observations

Surface air temperatures observed from stations around Antarctica have indicated predominantly positive trends which are as high as 0.4K per decade along the Antarctic Peninsula. Since the average air temperature during summer in the West Antarctic region is about -6 K, and since most of the stations are near coastal regions, it is important to know whether such trends are due to a local or large scale phenomenon. We analyzed about 19 years of infrared satellite data (1979-1997) to obtain a spatially detailed study of the variability of surface temperatures over the entire Antarctic region. We also analyzed potential impact of temperature changes over the sea ice cover using co-registered and nearly coincident microwave satellite data. The surface temperatures inferred from infrared data are shown to agree well with those observed from the limited number of Antarctic station data with a correlation coefficient of 0.98 and a standard deviation of less than 3K. The 19-year temperature data set shows positive trends of 0.12, 0.68, and 0.41 C per decade in ocean, sea ice and ice sheet surfaces, respectively. The sensitivity of the trend to record length was studied, using long term station data sets, and the results show that the trends start to stabilize at around 2 decades which is about the record length of satellite data. However, interannual fluctuations of the temperatures are large, especially in the ice sheets, and the 95% confidence level for the trends ranges from 0.12 to 1.22 for sea ice and from -0.74 to 1.55 C per decade for the ice sheet. In the sea ice regions, the position of the ice edge in winter with respect to the northernmost position of sea ice during the study period is also shown to be influenced by alternating warm and cold anomalies around the continent. This pattern is similar to that suggested by the presence of the Antarctic Circumpolar Wave (ACW) but the wavenumber appears to be predominantly mode 3 (instead of reported mode 2) for the Antarctic region. Unexpectedly, trends in the sea ice extent are found to be positive in most Antarctic sectors during the same period with the exception of the Bellingshausen and Amundsen Seas region.

Comisc, J. C.↗