Results for “Efficient recycling” — Page 4

DOE OSTI2021

Theoretical Analysis of a Single-Stage Gas-fired Ejector Heat Pump Water Heater

Ejector-driven systems have the ability to operate at high efficiencies, utilizing recycled thermal energy as a power source. For a typical ejector heat pump (EHP) system, the increase of the condenser temperature reduces the coefficient of performance (COP). In addition, if the condenser temperature is higher than the critical temperature, the ejector may not function. In this situation, the condenser temperature must be reduced, and an additional heater will be utilized to heat the production water from the condenser temperature to the desired temperature. In this study, a single-stage gas-fired EHP is investigated and thermodynamically modeled to optimize the system COP for the purpose of heating water by utilizing the thermal energy from the ambient air. The effects of the high-temperature evaporator (HTE) and low-temperature evaporator (LTE) on the ejector critical back pressure and the EHP system performance are examined for a HTE temperature range of 120–180 °C and LTE temperatures of 15.5, 17.5, and 19.5 °C. Our results show that an optimized COP for the EHP system exists and is dependent on HTE and LTE temperatures and the primary nozzle throat diameter. In addition, it is found that the peak EHP COP does not necessarily coincide with a large ejector COP. From this study, a maximum EHP COP of 1.31 is achieved at a HTE temperature of 170 °C and LTE temperature of 19.5 °C with a total heating capacity of 15.98 kW.

42 ENGINEERING↗

DOE OSTI2021

Theoretical Analysis of a Single-Stage Gas-Fired Ejector Heat Pump Water Heater

Ejector driven systems have the ability to operate at high efficiencies, utilizing recycled thermal energy as a power source. For a typical ejector heat pump system, the increase of the condenser temperature reduces the coefficient of performance (COP). In addition, if the condenser temperature is higher than the critical temperature, the ejector may not function. In this situation, the condenser temperature must be reduced, and an additional heater will be utilized to heat the production water from the condenser temperature to the desired temperature. In this investigation, a single-stage gas-fired ejector heat pump (EHP) is investigated and thermodynamically modeled in order to optimize the system COP for the purpose of heating water by utilizing the thermal energy from the ambient air. The effects of the high-temperature evaporator (HTE) and low-temperature evaporator (LTE) temperatures on the ejector critical back pressure and the EHP system performance are examined for a HTE temperature range of 120–180 °C and LTE temperatures of 15.5, 17.5, and 19.5 °C. Results show that an optimized COP of the EHP system exists which depends on HTE and LTE temperatures, primary nozzle throat diameters. In addition, it is found that the EHP COP is independent of the ejector COP. From this investigation a maximum EHP COP of 1.31 is able to be achieved for a HTE temperature of 160 °C and a LTE temperature of 19.5 °C with a total heat capacity of 15.98 kW.

Spitzenberger, Jeremy↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2023

Decarbonization of Wastewater Treatment with Microalgae Processes.

Microalgae can contribute to the decarbonization of wastewater treatment by municipalities, industries and agriculture, by substituting sunlight for energy intensive conventional treatment processes, while capturing nutrients and carbon in the algal biomass. The carbon fixed into the algal biomass can be converted to renewable natural gas (RNG) using anaerobic digestion or into renewable diesel and sustainable aviation fuel (SAF) using hydrothermal liquefaction (HTL), with greatly reduce the carbon footprints compared to conventional fuels. Bioplastics, biofertilizers and other bioproducts from microalgae biomass also provide potential benefits in greenhouse gas (GHG) reduction and domestic supply chains. Microalgae technologies can counter eutrophication caused by harmful algal blooms by recovering nutrients, N and P, from wastewaters, and even from very low nutrient concentrations found in surface waters. CO2 is required in microalgae cultivation and wastewater treatment to support maximal rates of the photosynthesis, with the CO2 obtained from the wastes themselves, other local sources or even atmospheric CO2. Greenhouse gas mitigation with microalgae processes is based on life cycle assessments, comparing such green processes with current energy intensive wastewater treatment, and nutrient reduction technologies. Microalgae technologies are specifically relevant to smaller, often disadvantaged, communities, where currently about 5,000 algae wastewater treatment ponds are operated by public utilities with many more are operated by industries. However, many, if not most, of these pond facilities require urgent technology upgrades to achieve the potential and goals of low cost GHG mitigation and efficient nutrient recycling. MicroBio Engineering Inc. is developing and has demonstrated several technologies that combine innovative carbon mitigation and decarbonization technologies for a circular economy, with longer-term potential for large-scale biofuels and biofertilizer production.

09 BIOMASS FUELS↗

DOE OSTI2025

Computationally Guided and Experimentally Validated Design of Custom Chelators for Critical Mineral Recovery

Selective, high throughput separation of target critical metals from complex environments such as fly ash leachates and mining process streams presents a significant challenge for economical production. Custom chelators and sorbents are an attractive technology for selective metal extraction, however it can be difficult to predict their performance, and significant experimental efforts are often required to develop chelating technologies. Here, we present a computational strategy focused on modelling chelator-metal binding interactions and benchmark these results versus experimental data. A computational pipeline combining forcefield, semiempirical, and meta-GGA methods with a thermodynamic framework optimized for error cancellation has been developed to predict binding energies of chelator complexes towards critical mineral recovery applications. This approach, originally validated on [2.2.2] cryptates binding mono- and divalent cations, demonstrated robust predictive capabilities with an R2 of 0.850 against experimental aqueous binding energies. The workflow includes metadynamics for exploring high-dimensional potential energy surfaces and a cluster-continuum model for accurate yet computationally efficient solvation modeling. Error cancellation between solvation energies of free and chelator-coordinated ions enables faster convergence, even with finite cluster sizes. Initial studies on the cryptates revealed consistent metal-ligand coordination patterns, with systematic variations influenced by ion size and charge, highlighting key structural features linked to binding selectivity. Further studies of a proprietary chelator have resulted in identification of previously unreported selectivity towards economically significant metals, which in-house experiments have confirmed, demonstrating the feasibility of this approach. By applying this methodology to new chelators targeting critical minerals such as lithium, cobalt, nickel and other strategic metals, we aim to accelerate the discovery of next-generation chelators for efficient recovery, recycling, and separation processes. This computational framework serves as the backbone of a high-throughput design pipeline tailored for sustainable resource utilization and may be applied to a wide range of systems to meet experimental needs.

computational materials↗

DOE OSTI2024

Revolutionizing Waste Management: AI-Powered Real-Time Characterization for Efficient Handling of Non-Recyclable Municipal Solid Waste

According to EPA, -300 MM tons of municipal solid waste (MSW) was available in the US as of 2018. Of that total material, nearly 50% was landfilled resulting in a significant loss for the potential to convert its energy value into cost effective and sustainable biofuels. Redirecting this material away from the landfill and into conversion ready feedstock for energy generation can directly address DOE's selling price < $2.50/GGE while securing the US national energy independence [1]. However, the paramount challenges in any rational fuel conversion strategy are understanding the chemical makeup, quality and associated calorific value of the MSW. Understanding these parameters is critical in achieving any acceptable fuel conversion and requires rapid characterization followed by accurate separation technologies. Therefore, we are proposing to address the rapid characterization by building a non-invasive, rapid, and highly accurate Artificial Intelligence (AI)-enabled spectrometric/optical approach augmented with multi-sensory information for advanced characterization of domestic heterogeneous MSW. North Carolina State University (NCSU) and the National Renewable Energy Laboratory (NREL), in partnership with strong support from the Town of Cary and IBM, Inc., will closely work together to implement this ground-breaking technology for the effective characterization of MSW for sustainable and affordable production of conversion-ready feedstocks, while solving the environment issue of planetary proportions.

artificial intelligence↗

DOE OSTI2021

Uranium In Situ Electrolytic Deposition with a Reusable Functional Graphene-Foam Electrode

Nuclear fission produces 400 GWe which represents 11% of the global electricity output. Uranium is the essential element as both fission fuel and radioactive waste. Therefore, the recovery of uranium is of great importance. In this study, an in situ electrolytic deposition method to extract uranium from aqueous solution is reported. A functionalized reduced graphene oxide foam (3D-FrGOF) is used as the working electrode, which acts as both a hydrogen evolution reaction catalyst and a uranium deposition substrate. The specific electrolytic deposition capacity for U(VI) ions with the 3D-FrGOF is 4560 mg g –1 without reaching saturation, and the Coulombic efficiency can reach 54%. Moreover, reduction of the uranium concentration in spiked seawater from 3 ppm to 19.9 ppb is achieved, which is lower than the US Environmental Protection Agency uranium limits for drinking water (30 ppb). Furthermore, the collection electrode can be efficiently regenerated and recycled at least nine times without much efficiency fading, by ejecting into 2000 ppm concentrated uranium solution in a second bath with reverse voltage bias. All these findings open new opportunities in using free-standing 3D-FrGOF electrode as an advanced separation technique for water treatment.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Application of Ionic Liquids for the Recycling and Recovery of Technologically Critical and Valuable Metals

Population growth has led to an increased demand for raw minerals and energy resources; however, their supply cannot easily be provided in the same proportions. Modern technologies contain materials that are becoming more finely intermixed because of the broadening palette of elements used, and this outcome creates certain limitations for recycling. The recovery and separation of individual elements, critical materials and valuable metals from complex systems requires complex energy-consuming solutions with many hazardous chemicals used. Significant pressure is brought to bear on the improvement of separation and recycling approaches by the need to balance sustainability, efficiency, and environmental impacts. Due to the increase in environmental consciousness in chemical research and industry, the challenge for a sustainable environment calls for clean procedures that avoid the use of harmful organic solvents. Ionic liquids, also known as molten salts and future solvents, are endowed with unique features that have already had a promising impact on cutting-edge science and technologies. This review aims to address the current challenges associated with the energy-efficient design, recovery, recycling, and separation of valuable metals employing ionic liquids.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A separations and purification process for improving yields and meeting fuel contaminant specifications for high-octane gasoline produced from dimethyl-ether over a Cu/BEA catalyst

In this work, we have been developing a three-step conversion of biomass-derived syngas to methanol to dimethyl-ether (DME) to non-aromatic hydrocarbons for use as high-octane gasoline and sustainable aviation fuel. This process produces branched alkanes from DME using a Cu/BEA catalyst and is a promising alternative to other syngas conversion processes such as Fischer-Tropsch to linear alkanes and traditional ZSM-5 catalyzed methanol to aromatic gasoline. In this short article we describe some advances in our understanding related to separations and purification via the use of more detailed experimental speciation in an updated process model involving multiple phase equilibrium-based separation steps. Primary modeled reactor outlet constituents (and weight %) are: C3 and lighter hydrocarbon gases (11.1%), C4s (54.5%), H 2 (1.2%), CO 2 (2.9%), water (5.0%), unreacted DME (16.5%), methanol (2.3%), and C5+ hydrocarbons (6.4%). DME (the primary reactant) and H 2 recycle and reuse are important for the overall process efficiency, and the recycle of C4s is important to increase the C5+ yield via reactivation and homologation. Thus H 2 , C4s, and DME are targeted for recycle, while methanol and water need to be removed from the product to conform with fuel specifications. Model predictions from Aspen Plus using the NRTL-RK property method indicate a fuel composition with C5+ content of 97.1 wt%, with minor constituents: 2.4 wt% C4s, 0.3 wt% methanol, 0.1 wt% DME, 0.03 wt% water, and 0.01 wt% C3s. These ranges of minor components conform with fuel quality requirements, and the modeled product is amenable for unconstrained blending to boost gasoline octane ratings.

09 BIOMASS FUELS↗

DOE OSTI2023

Evaluation of two extraction chromatography resins for scandium and titanium separation for medical isotope production

Scandium-47 ( 47 Sc) can be used in nuclear medicine as a therapeutic-diagnostic, or "theragnostic," radioactive medical isotope for cancer detection and treatment. The 47 Sc isotope can be produced through the photonuclear reaction 48 Ti(γ,p) 47 Sc by irradiating enriched 48 Ti target material. The enriched target material necessary for production is costly; 48 TiO 2 costs ~ $\$$1550/g, and targets can be > 50 g ($\$$77,500) to produce medically relevant amounts of 47 Sc. In order to keep costs low, a highly efficient separation of scandium from bulk titanium is desired, along with efficient methods for recycling the target material. Here this research is focused on evaluating efficient methods for the separation of scandium from bulk quantities of titanium using commercially available diglycolamide-based and hydroxamate-based extraction chromatography resins (DGA resin and ZR resin, respectively). The sorption of 47 Sc and Ti on these resins were investigated at varying concentrations of HNO 3 , HCl, H 2 SO 4 , and HF to explore how they might be used in a large-scale production/processing setting.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

DOE OSTI2024

Depolymerizable and recyclable luminescent polymers with high light-emitting efficiencies

Luminescent polymers are of great interest in a number of photonic technologies, including electroluminescence, bioimaging, medical diagnosis, bio-stimulation and security signage. Incorporating depolymerizability and recyclability into luminescent polymers is pivotal for promoting their sustainability and minimizing their environmental impacts at the end of the product lifecycle, but existing strategies often compromise the light-emitting efficiencies. Here, in this study, we develop a strategy that utilizes cleavable moiety to create depolymerizable and recyclable thermally activated delayed fluorescence (TADF) polymers without compromising their high light-emitting efficiencies. The electroluminescent devices based on the TADF polymers achieved a high external quantum efficiency of up to 15.1 %. The TADF polymers can be depolymerized under either mild acidic or heating conditions, with precise control of the kinetics, and the obtained pure monomers can potentially be isolated and repolymerized for subsequent life applications. This work promotes the end-of-life environmental friendliness and circularity of luminescent materials, paving the way to a sustainable photonic industry. Developing depolymerizable and recyclable polymers with high light-emitting efficiencies is of vital importance for sustainable photonic technologies, but remains challenging. Here the authors design a strategy to develop such polymers based on the use of controllable cleavable moiety.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Advances in ionic liquid recycling for lignocellulosic biomass pretreatment

Ionic liquids (ILs) are promising solvents for the pretreatment of lignocellulosic biomass due to their ability to disrupt cellulose, hemicellulose, and lignin structures. However, large-scale implementation requires the development of efficient recovery and recycling methods. This review provides a comprehensive analysis of the recyclability potential of ILs used in biomass pretreatment, emphasizing their mechanisms, recent innovations, and ongoing challenges. We begin by discussing the structural diversity and tunability of ILs, which underlie their effectiveness in biomass deconstruction. The distinct roles of IL anions and cations in dissolving specific biomass components are systematically presented and compared. Advances in IL recycling techniques, including antisolvent precipitation methods, membrane separation, and distillation, are critically examined, with attention to how mechanistic insights can inform the design of more efficient and selective recovery strategies. Despite progress, significant challenges remain to scaling up IL-based biomass processing, including high cost, environmental concerns, and impact of biomass-derived impurities (e.g., lignin residues, sugars, proteins) on IL purity and functionality after reuse. We also review the applicability of different ILs based on life cycle assessments and techno-economic analyses. Lastly, we identify critical research gaps and propose future directions, including the design and development of next-generation ILs with improved recyclability, reduced toxicity, and enhanced economic viability for industrial-scale applications.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Process Scale-Up of an Energy-Efficient Membrane Solvent Extraction Process for Rare Earth Recycling from Electronic Wastes

This study reports the process scale-up and long-term performance of an energy-efficient and cost-effective membrane solvent extraction (MSX) process for separation and recovery of high purity rare earth oxides (REOs) from scrap permanent magnets (SPMs). Here, the rare earth elements (REEs), including dysprosium, neodymium, and praseodymium, are recovered from SPMs using a neutral extractant, tetraoctyl diglycolamide (TODGA) embedded in a microporous polypropylene hollow fiber membrane module. The MSX process performance is demonstrated with bench scale module with membrane surface area of 1.4 m 2 to industrial scale modules with membrane surface area of up to 20 m2 to enable the processing of up to 1 ton month –1 of SPMs. The purity and the yield of the recovered REOs are >99.5 wt% and >95%, respectively. The average extraction rate of REOs is >10 g m –2 hr –1 . A skid of MSX system is assembled with a membrane area of 40 m 2 . The MSX skid successfully recovers REOs with a capacity of 300 kg REOs/month. Finally, it is determined that the organic phase containing the extractant maintains its performance up to 250 h. The results suggest that the MSX process is an economically viable and environmentally friendly process for separation and recovery of REOs from electronic wastes.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Efficient separation and coprecipitation for simplified cathode recycling

Hydrometallurgical recycling of spent lithium-ion batteries is among the most promising recovery approaches. The current hydrometallurgical method for battery recycling faces challenges such as complex separation and precipitation processes, and environmental concerns from the use of caustic inorganic acid and hazardous hydrogen peroxide. Our proposed modified method, namely polyol-metallurgy, uses citric acid in ethylene glycol as dual-function green solution to overcome these obstacles. This bifunctional solution leaches valuable metal ions from cathode materials (e.g., LiCoO 2 ), and then acts as chelating agents to selectively precipitate cobalt through an esterification reaction, without the need for additional precipitation agents. The leaching efficiency of cobalt and lithium reaches 99.55% and 97.65%, respectively, and more than 96% of cobalt could be directly self-precipitated and recovered. Further, the unique characteristics of the dual-function solution also avoids impurities from Al foils and PVDF/carbon black films, enabling the simple separation process. Therefore, the process can be completed in one-pot system with efficient leaching, separation and coprecipitation, making it more efficient and feasible for operation than existing alternatives.

25 ENERGY STORAGE↗

DOE OSTI2026

Ambient-Pressure Chemical Recycling of Thermoset Carbon Fiber-Reinforced Polymers via Low-Temperature Solvolysis: Techno-Economic and Life-Cycle Assessment

Carbon fiber-reinforced polymer (CFRP) waste is rapidly accumulating, with global volumes projected to exceed 500,000 tons annually by 2050. Virgin carbon fiber production is extremely energy- and cost-intensive, and growing demand has intensified supply-chain vulnerabilities associated with precursor availability and reliance on critical materials. Scalable recycling technologies therefore offer not only environmental benefits but also opportunities to reduce material costs and strengthen domestic composite supply chains. This study introduces an efficient, mild chemical recycling method for epoxy-amine CFRPs, utilizing acetic acid (80 wt%) and zinc acetate (1 wt%) at atmospheric pressure and low temperature (~110 °C). The solvolysis process preserves residual resin (~40%) on recycled carbon fibers (rCF), enhancing interfacial bonding in remanufactured composite materials. Recycled fibers retain ~90% of their mechanical properties, and recovered oligomers show potential for reuse in epoxy formulations, supporting material circularity. Techno-economic analysis (TEA) and life-cycle assessment (LCA) confirm the scalability and sustainability of this process.

Recycling CFRP↗

DOE OSTI2024

Leverage modern artificial intelligence (AI) enabled systems for waste reduction

Manufacturing industries continue to face challenges in reducing waste, as upstream strategies such as source reduction and product redesign require a deeper understanding of processes compared to conventional recycling methods. Recent advancements in artificial intelligence (AI) and machine learning (ML) have opened new opportunities to integrate modern computational techniques with traditional waste minimization strategies. This paper explores AI-enabled approaches for product redesign, source reduction, and recycling that can significantly reduce waste generation while improving efficiency and sustainability. AI-driven material substitution and lightweighting in product design enable discovery of novel materials with optimized properties, reducing waste without compromising performance. Reinforcement learning models optimize process parameters, raw material specifications, and machine sequencing to minimize production losses, while Industrial Internet of Things (IIoT) systems paired with AI analytics enhance real-time waste tracking, predictive maintenance, and quality inspection. Furthermore, AI-based demand forecasting and production planning reduce overproduction and excess inventory, as demonstrated in industrial applications. In recycling, ML-powered pattern recognition and robotic sorting technologies achieve higher accuracy in waste segregation, directly improving recycling efficiency. Complementary solutions such as smart bins and AI-enabled waste pickup scheduling optimize collection logistics, reducing both costs and emissions. Although implementation requires upfront investment in infrastructure and training, the long-term benefits include higher material efficiency, reduced waste, improved product quality, and stronger sustainability outcomes across the supply chain. By leveraging AI-enabled systems, manufacturers can align waste minimization efforts with circular economy principles, creating scalable solutions for both industry and society.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2022

Selective bacterial separation of critical metals: towards a sustainable method for recycling lithium ion batteries

The large scale recycling of lithium ion batteries (LIBs) is essential to satisfy global demands for the raw materials required to implement this technology as part of a clean energy strategy. However, despite what is rapidly becoming a critical need, an efficient and sustainable recycling process for LIBs has yet to be developed. Biological reactions occur with great selectivity under mild conditions, offering new avenues for the implementation of more environmentally sustainable processes. Here, we demonstrate a sequential process employing two bacterial species to recover Mn, Co and Ni, from vehicular LIBs through the biosynthesis of metallic nanoparticles, whilst Li remains within the leachate. Moreover the feasibility of Mn recovery from polymetallic solutions was demonstrated at semi-pilot scale in a 30 L bioreactor. Additionally, to provide insight into the biological process occurring, we investigated selectivity between Co and Ni using proteomics to identify the biological response and confirm the potential of a bio-based method to separate these two essential metals. Our approach determines the principles and first steps of a practical bio-separation and recovery system, underlining the relevance of harnessing biological specificity for recycling and up-cycling critical materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗