Search NASA⌕ Search

SEARCH · Search NASA

Results for “Energy - Natural gas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Life cycle cost assessment of future low heat rejection engines

The Adiabatic Diesel Engine Component Development (ADECD) represents a project which has the objective to accelerate the development of highway truck engines with advanced technology aimed at reduced fuel consumption. The project comprises three steps, including the synthesis of a number of engine candidate designs, the coupling of each with a number of systems for utilizing exhaust gas energy, and the evaluation of each combination in terms of desirability. Particular attention is given to the employed evaluation method and the development of this method. The objective of Life Cycle Cost (LCC) evaluation in the ADECD program was to select the best from among 42 different low heat rejection engine (LHRE)/exhaust energy recovery system configurations. The LCC model is discussed along with a maintenance cost model, the evaluation strategy, the selection of parameter ranges, and a full factorial analysis.

Petersen, D. R.↗
NASA NTRS1973

Normal and Tangential Momentum Accommodation for Earth Satellite Conditions

Momentum accommodation was determined experimentally for gas-surface interactions simulating in a practical way those of near-earth satellites. Throughout the ranges of gas energies and incidence angles of interest for earth-conditions, two components of force were measured by means of a vacuum microbalance to determine the normal and tangential momentum-accommodation coefficients for nitrogen ions on technical-quality aluminum surfaces. For these experimental conditions, the electrodynamics of ion neutralization near the surface indicate that results for nitrogen ions should differ relatively little from those for nitrogen molecules, which comprise the largest component of momentum flux for near-earth satellites. The experimental results indicated that both normal and tangential momentum-accommodation coefficients varied widely with energy, tending to be relatively well accommodated at the higher energies, but becoming progressively less accommodated as the energy was reduced to and below that for earth-satellite speeds. Both coefficients also varied greatly with incidence angle, the normal momentum becoming less accommodated as the incidence angle became more glancing, whereas the tangential momentum generally became more fully accommodated. For each momentum coefficient, an empirical correlation function was obtained which closely approximated the experimental results over the ranges of energy and incidence angle. Most of the observed variations of momentum accommodation with energy and incidence angle were qualitatively indicated by a calculation using a three-dimensional model that simulated the target surface by a one-dimensional attractive potential and hard sphere reflectors.

Knechtel, Earl D.↗
NASA NTRS2000

Raman Shifting a Tunable ArF Excimer Laser to Wavelengths of 190 to 240 nm With a Forced Convection Raman Cell

Tunable radiation, at ultraviolet wavelengths, is produced by Raman shifting a modified 285-mJ ArF excimer laser. Multiple Stokes outputs are observed in H2, CH4, D2, N2, SF6, and CF4 (20, 22, 53, 21, 2.1, and 0.35 percent, respectively). Numbers in parentheses are the first Stokes energy conversion efficiencies. We can access 70 percent of the frequency range 42000-52000 cm (exp -1) (190-240 nm) with Stokes energies that vary from 0.2 microJoule to 58 mJ inside the Raman cell. By using 110 mJ of pump energy and D 2 , the tunable first Stokes energy varies over the 29-58 mJ range as the wavelength is tuned over the 204-206 nm range. Dependence on input energy, gas pressure, He mixture fraction, and circulation of the gas in the forced convection Raman cell is discussed; Stokes conversion is also discussed for laser repetition rates from 1 to 100 Hz. An empirical equation is given to determine whether forced convection can improve outputs for a given repetition rate.

Balla, R. Jeffrey↗
NASA NTRS2000

Magnetic Flux Compression Concept for Nuclear Pulse Propulsion and Power

The desire for fast, efficient interplanetary transport requires propulsion systems having short acceleration times and very high specific impulse attributes. Unfortunately, most highly efficient propulsion systems which are within the capabilities of present day technologies are either very heavy or yield very low impulse such that the acceleration time to final velocity is too long to be of lasting interest, One exception, the nuclear thermal thruster, could achieve the desired acceleration but it would require inordinately large mass ratios to reach the range of desired final velocities. An alternative approach, among several competing concepts that are beyond our modern technical capabilities, is a pulsed thermonuclear device utilizing microfusion detonations. In this paper, we examine the feasibility of an innovative magnetic flux compression concept for utilizing microfusion detonations, assuming that such low yield nuclear bursts can be realized in practice. In this concept, a magnetic field is compressed between an expanding detonation driven diamagnetic plasma and a stationary structure formed from a high temperature superconductor (HTSC). In general, we are interested in accomplishing two important functions: (1) collimation of a hot diamagnetic plasma for direct thrust production; and (2) pulse power generation for dense plasma ignition. For the purposes of this research, it is assumed that rnicrofusion detonation technology may become available within a few decades, and that this approach could capitalize on recent advances in inertial confinement fusion ICF) technologies including magnetized target concepts and antimatter initiated nuclear detonations. The charged particle expansion velocity in these detonations can be on the order of 10 (exp 6)- 10 (exp 7) meters per second, and, if effectively collimated by a magnetic nozzle, can yield the Isp and the acceleration levels needed for practical interplanetary spaceflight. The ability to ignite pure fusion micro-bursts with reasonable levels of input energy is an equally challenging scientific problem. It remains to be seen, however, whether an effective ignition driver can be developed which meets the requirements for practical spaceflight application (namely high power density, compactness, low weight, and low cost). In this paper, system level performance and design issues are examined including generator performance, magnetic flux compression processes, magnetic diffusion processes, high temperature superconductor (HTSC) material properties, plasmadynamic processes, detonation plasma expansion processes, magnetohydrodynamic instabilities, magnetic nozzle performance, and thrust production performance. Representative generator performance calculations based on a simplified skin layer formulation are presented as well as the results of exploratory small-scale laboratory experiments on magnetic flux diffusion in HTSC materials. In addition, planned follow-on scientific feasibility experiments are described which utilize high explosive detonations and high energy gas discharges to simulate the plasma conditions associated with thermonuclear micro-detonations.

Litchford, Ronald J.↗
NASA NTRS2000

BOREAS TF-1 SSA-OA Weekly Tower CH4 and N2O Flux

The BOREAS TF-1 team collected various trace gas and energy flux data in its efforts to characterize the temporal energy and gas exchanges that occurred over the SSA-OA site. This data set contains methane (CH4) and nitrous oxide (N2O) fluxes that were measured at the BOREAS SSA-OA site. These fluxes were measured from 16-Apr to 16-Sep-1994. The data were averaged to weekly values and are available in tabular ASCII files.

Thurtell, George↗
NASA NTRS2005

An Approximate Ablative Thermal Protection System Sizing Tool for Entry System Design

A computer tool to perform entry vehicle ablative thermal protection systems sizing has been developed. Two options for calculating the thermal response are incorporated into the tool. One, an industry-standard, high-fidelity ablation and thermal response program was integrated into the tool, making use of simulated trajectory data to calculate its boundary conditions at the ablating surface. Second, an approximate method that uses heat of ablation data to estimate heat shield recession during entry has been coupled to a one-dimensional finite-difference calculation that calculates the in-depth thermal response. The in-depth solution accounts for material decomposition, but does not account for pyrolysis gas energy absorption through the material. Engineering correlations are used to estimate stagnation point convective and radiative heating as a function of time. The sizing tool calculates recovery enthalpy, wall enthalpy, surface pressure, and heat transfer coefficient. Verification of this tool is performed by comparison to past thermal protection system sizings for the Mars Pathfinder and Stardust entry systems and calculations are performed for an Apollo capsule entering the atmosphere at lunar and Mars return speeds.

Dec, John A.↗
NASA NTRS2006

An Approximate Ablative Thermal Protection System Sizing Tool for Entry System Design

A computer tool to perform entry vehicle ablative thermal protection systems sizing has been developed. Two options for calculating the thermal response are incorporated into the tool. One, an industry-standard, high-fidelity ablation and thermal response program was integrated into the tool, making use of simulated trajectory data to calculate its boundary conditions at the ablating surface. Second, an approximate method that uses heat of ablation data to estimate heat shield recession during entry has been coupled to a one-dimensional finite-difference calculation that calculates the in-depth thermal response. The in-depth solution accounts for material decomposition, but does not account for pyrolysis gas energy absorption through the material. Engineering correlations are used to estimate stagnation point convective and radiative heating as a function of time. The sizing tool calculates recovery enthalpy, wall enthalpy, surface pressure, and heat transfer coefficient. Verification of this tool is performed by comparison to past thermal protection system sizings for the Mars Pathfinder and Stardust entry systems and calculations are performed for an Apollo capsule entering the atmosphere at lunar and Mars return speeds.

Dec, John A.↗
NASA NTRS2014

Solid Rocket Launch Vehicle Explosion Environments

Empirical explosion data from full scale solid rocket launch vehicle accidents and tests were collected from all available literature from the 1950s to the present. In general data included peak blast overpressure, blast impulse, fragment size, fragment speed, and fragment dispersion. Most propellants were 1.1 explosives but a few were 1.3. Oftentimes the data from a single accident was disjointed and/or missing key aspects. Despite this fact, once the data as a whole was digitized, categorized, and plotted clear trends appeared. Particular emphasis was placed on tests or accidents that would be applicable to scenarios from which a crew might need to escape. Therefore, such tests where a large quantity of high explosive was used to initiate the solid rocket explosion were differentiated. Also, high speed ground impacts or tests used to simulate such were also culled. It was found that the explosions from all accidents and applicable tests could be described using only the pressurized gas energy stored in the chamber at the time of failure. Additionally, fragmentation trends were produced. Only one accident mentioned the elusive "small" propellant fragments, but upon further analysis it was found that these were most likely produced as secondary fragments when larger primary fragments impacted the ground. Finally, a brief discussion of how this data is used in a new launch vehicle explosion model for improving crew/payload survival is presented.

Richardson, E. H.↗
DOE OSTI2022

JISEA Annual Meeting: Clean Energy for Oil and Gas Topic Table

Presentation on clean energy for oil and gas topic discussion table at the 2022 JISEA annual meeting. Many refineries may have wind and solar resources and clean energy technology costs are declining. JISEA created an oil and gas consortium including Baker Hughes, Conoco Phillips, Extraction Oil & Gas, INGAA Foundation, and Kinder Morgan to explore potential pathways for integrating clean energy into oil and gas operations. This presentation goes over JISEA case studies that demonstrate reliable and affordable clean power for oil and gas operations. JISEA used the REopt Energy Planning Platform and evaluated several potential future scenarios.

clean energy↗
DOE OSTI2022

Enabling Technology - Reducing Greenhouse Gas Emissions and Energy Demands in the Meat Production Industry via Scaling Advanced 3D Culture Bioreactors

The project “Enabling Technology - Reducing Greenhouse Gas Emissions and Energy Demands in the Meat Production Industry via Scaling Advanced 3D Culture Bioreactors” focuses on developing transformational and disruptive food technologies, specifically in the area of alternative protein and meat production techniques. The impetus for developing alternative protein technologies include reducing intensive greenhouse gas emissions and energy/land/water usages associated with conventional meat production (animal agriculture). Additional rationales include providing alternatives to livestock rearing as a means of reducing antimicrobial resistance (most antibiotic and antimicrobial use occurs in food-producing animals), as well as the transmission of zoonotic diseases. The goal of this ARPA-E project was to research and develop novel and effective technologies to produce cell-cultured meat (also named in vitro meat, cultivated meat). Cell-cultured meat is an alternative protein or meat technology that involves directly growing muscle and fat tissues (which comprise meat) without using the full animal. This offers benefits in terms of animal welfare (elimination of animal slaughter), while also being projected to be more resource efficient in terms of metrics such as land use and greenhouse gas emissions, especially when compared to beef and lamb. Cell cultured meat additionally offers greater control over the cultivated cells, enabling more precise control over nutrition and taste. For example, cultured cells could be tuned to produce antioxidants such as carotenoids to improve human health. However, to date there are no scalable methods of producing cell-cultured meat cheaply at a large scale.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Clean Energy in Oil & Gas Consortium: Compressor Station Case Study

JISEA conducted analysis of technical and economic potential of incorporating low-emissions energy sources into various oil and gas operations in different locations to assist the oil and gas industry with decision-making. The case study analysis presented here evaluated renewable energy opportunities at an all-electric compressor station located in Texas.

Baker Hughes↗
NASA NTRS1991

The metal abundance and specific energy of intracluster gas

The hot gas in the cores of rich galaxy clusters is metal-rich with nearly solar abundances of metals. It is not clear whether the metals were shed from galaxies via protogalactic winds or via ram-pressure stripping. It has been suggested that if metals were injected via centrally concentrated stripping, the overall abundances could be much less than those observed in cluster cores, diminishing the degree of stellar processing required. The observed energetics of intracluster gas can be used to deduce the metal injection mechanism, which in turn may allow the global metal abundance uncertainty to be resolved in the absence of spatially resolved X-ray spectra. Existing X-ray spectral and surface brightness data for galaxy clusters indicate that the gas in cool clusters has substantially greater specific energy than could have been gained through cluster collapse. Supernovae-driven protogalactic winds can provide this extra energy, while ram-pressure stripping cannot. Such protogalactic winds will distribute metals fairly homogeneously. Much processing of gas through stars is then required, with protogalaxies losing perhaps one-half of their initial luminous mass in metal-rich winds. Furthermore, the oxygen-to-iron ratio observed in two clusters indicates that the bulk of the iron in cluster gas was produced by Type II supernovae, not Type I supernovae, as is usually supposed.

White, Raymond E., III↗
DOE OSTI2025

Supply Chain Energy and Greenhouse Gas Analysis Using the Materials Flows Through Industry (MFI) Tool: Examination of Alternative Technology Scenarios for the U.S. Chemical Sector

Chemical manufacturing is a large and diverse sector of the U.S. economy, with products, fuels, and a wide assortment of materials used daily by both the public and businesses. Currently, several of the largest volume chemicals produced in the United States rely on fossil fuels as a feedstock, energy source, or both. The list of chemicals includes steam cracking products such as ethylene, propylene, benzene, and xylenes as well as products such as ammonia and methanol. The focus for this work is on platform chemicals that are both produced in the largest volume and have a high potential for subsequent processing into more specialized products. In this study, we explore several new pathways that reduce the overall energy consumption and greenhouse gas (GHG) emissions for each product. These pathways include energy efficiency measures applied to existing production methods, the use of bio‐based fuels and/or feedstocks as new production methods, and electrification of high‐energy‐input stages within current production methods. Scenarios for energy demand and GHG reduction were conducted with the National Renewable Energy Laboratory's Materials Flows through Industry tool. Projections of the energy demand and GHG emissions in 2030 and 2050 are included, using grid composition projections from the NREL ReEDS model. The alternative scenarios selected showcase the effect of realistic changes the industry could make, focusing on technologies with a high level of technical readiness.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
NASA NTRS1997

Rotational Energy Transfer of N2 Gas Determined Using a New Ab Initio Potential Energy Surface

Rotational energy transfer between two N2 molecules is a fundamental process of some importance. Exchange is expected to play a role, but its importance is somewhat uncertain. Rotational energy transfer cross sections of N2 also have applications in many other fields including modeling of aerodynamic flows, laser operations, and linewidth analysis in nonintrusive laser diagnostics. A number of N2-N2 rigid rotor potential energy surface (PES) has been reported in the literature.

Huo, Winifred M.↗
DOE OSTI2023

Supply Chain Energy and Greenhouse Gas Analysis Using the Materials Flows through Industry (MFI) Tool: Examination of Decarbonization Technology Scenarios for the U.S. Glass Manufacturing Sector

Glass manufacturing is a major part of the U.S. economy, and glass products in multiple sectors - flat glass, container glass, and fiberglass - are a part of everyday life. Despite glass manufacturing's long history, there are still many opportunities for glass production to improve in terms of both in overall energy consumption and greenhouse gas (GHG) emission reduction. Scenarios for the flat, container, and fiberglass sectors show the effect that each improvement has on primary energy demand and GHG emissions, starting from an industry baseline that reflects current manufacturing practices. Using the National Renewable Energy Laboratory's Material Flows through Industry tool, multiple scenarios are examined for each glass sector by applying a combination of energy reduction, increased electrification, hydrogen cofiring, a more renewable electric grid, and increased use of cullet. Additional decarbonization options are possible for glass but are left for later analysis due to cost, feasibility, or data issues. Primary energy demand can be reduced by 75%-83% compared to baseline inputs, depending on the sector, and GHG emissions are reduced by 82%-86%. Applying the maximum level of improvements listed here has the potential to save over 300 million GJ and 25 million metric tons of GHGs by 2050.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1989

A space-based combined thermophotovoltaic electric generator and gas laser solar energy conversion system

This paper describes a spaceborne energy conversion system consisting of a thermophotovoltaic electric generator and a gas laser. As a power source for the converson, the system utilizes an intermediate blackbody cavity heated to a temperature of 2000-2400 K by concentrated solar radiation. A double-layer solar cell of GaAs and Si forms a cylindrical surface concentric to this blackbody cavity, receiving the blackbody radiation and converting it into electricity with cell conversion efficiency of 50 percent or more. If the blackbody cavity encloses a laser medium, the blackbody radiation can also be used to simultaneously pump a lasing gas. The feasibility of blackbody optical pumping at 4.3 microns in a CO2-He gas mixture was experimentally demonstrated.

Yesil, Oktay↗
DOE OSTI2020

Life cycle greenhouse gas emissions and energy use of polylactic acid, bio-derived polyethylene, and fossil-derived polyethylene

Bioplastics recently have become an attractive, viable, and popular alternative to conventional petroleum-based plastics, with the hope that replacing fossil-derived plastics with renewable alternatives will reduce greenhouse gas (GHG) emissions and fossil energy consumption (FEC). The bioplastic industry is encouraging creative designs and enhanced properties such as biodegradability, which is considered a sustainable solution for waste plastic management. However, biodegradability also means that carbon in the product is emitted to the atmosphere as GHG emissions. In this paper, a life cycle analysis (LCA) of biodegradable polylactic acid (PLA) and bio-polyethylene (bio-PE) plastics was conducted to understand the environmental effects of these bioplastics from feedstock production to product end-of-life (EOL). In particular, emissions from biodegradability (EOL emissions) are accounted for. The results were compared to those of conventional fossil-based plastics such as high-density polyethylene (HDPE) and low-density polyethylene (LDPE). Results showed that the lowest GHG emissions (-1.0 and 1.7 kg CO 2 e per kg for bio-PE and PLA with no biodegradation, respectively) and FEC (29 and 46 MJ per kg of bio-PE and PLA, respectively) were achieved with bio-derived plastics, particularly bio-PE plastic. However, despite the benefits of biogenic carbon uptake, when landfill and composting emissions were considered for the PLA pathway, the life cycle emissions of PLA increase significantly, from 16% to 163% depending on the biodegradation condition, compared to the case where there is no degradation in the landfill. This study also contributed to understand the effects on the GHG emissions of biodegradability in landfill and composting scenarios, regional electricity mix, and plastics manufacturing technologies. (C) 2020 The Authors. Published by Elsevier Ltd.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Untapped Benefits of Porous Liquids for Gas Capture: Low-Energy Regeneration

Current liquid-phase gas capture materials incur high operational costs due to energy-intensive regeneration processes, creating an industrial need for alternative materials that retain engineering benefits while reducing energy requirements. Porous liquids (PLs), liquid-phase materials with permanent internal porosity, have emerged as promising replacements with excellent gas absorption capacity and selectivity. Despite these benefits, evaluation of regeneration in PLs remains rare. In this Perspective, we evaluate the effects of solvent interactions, mass transport, and binding site formation that control PL regeneration. While conventional regeneration methods exist in PLs, the diversity of PL compositions allows for novel regeneration processes including light irradiation via use of photosensitive azobenzene-based cages, isostatic compression to collapse internal pore structures, and localized heating via sonication for gas desorption. In conclusion, the wide variability in porous host materials that generate the internal porosity in PLs facilitates innovative low-energy regeneration pathways, positioning them as a transformative solution in separation technologies.

gas capture↗