SEARCH · Search NASA

Results for “Excellent Agreement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Analytical prediction with multidimensional computer programs and experimental verification of the performance, at a variety of operating conditions, of two traveling wave tubes with depressed collectors

Experimental and analytical results are compared for two high performance, octave bandwidth TWT's that use depressed collectors (MDC's) to improve the efficiency. The computations were carried out with advanced, multidimensional computer programs that are described here in detail. These programs model the electron beam as a series of either disks or rings of charge and follow their multidimensional trajectories from the RF input of the ideal TWT, through the slow wave structure, through the magnetic refocusing system, to their points of impact in the depressed collector. Traveling wave tube performance, collector efficiency, and collector current distribution were computed and the results compared with measurements for a number of TWT-MDC systems. Power conservation and correct accounting of TWT and collector losses were observed. For the TWT's operating at saturation, very good agreement was obtained between the computed and measured collector efficiencies. For a TWT operating 3 and 6 dB below saturation, excellent agreement between computed and measured collector efficiencies was obtained in some cases but only fair agreement in others. However, deviations can largely be explained by small differences in the computed and actual spent beam energy distributions. The analytical tools used here appear to be sufficiently refined to design efficient collectors for this class of TWT. However, for maximum efficiency, some experimental optimization (e.g., collector voltages and aperture sizes) will most likely be required.

Dayton, J. A., Jr.↗

NASA NTRS1992

Proton affinity of methyl nitrate - Less than proton affinity of nitric acid

Several state-of-the-art ab initio quantum mechanical methods were used to investigate the equilibrium structure, dipole moments, harmonic vibrational frequencies, and IR intensities of methyl nitrate, methanol, and several structures of protonated methyl nitrate, using the same theoretical methods as in an earlier study (Lee and Rice, 1992) of nitric acid. The ab initio results for methyl nitrate and methanol were found to be in good agreement with available experimental data. The proton affinity (PA) of methyl nitrate was calculated to be 176.9 +/-5 kcal/mol, in excellent agreement with the experimental value 176 kcal/mol obtained by Attina et al. (1987) and less than the PA value of nitric acid. An explanation of the discrepancy of the present results with those of an earlier study on protonated nitric acid is proposed.

Lee, Timothy J.↗

NASA NTRS2013

Advanced Optical Diagnostics for Ice Crystal Cloud Measurements in the NASA Glenn Propulsion Systems Laboratory

A light extinction tomography technique has been developed to monitor ice water clouds upstream of a direct connected engine in the Propulsion Systems Laboratory (PSL) at NASA Glenn Research Center (GRC). The system consists of 60 laser diodes with sheet generating optics and 120 detectors mounted around a 36-inch diameter ring. The sources are pulsed sequentially while the detectors acquire line-of-sight extinction data for each laser pulse. Using computed tomography algorithms, the extinction data are analyzed to produce a plot of the relative water content in the measurement plane. To target the low-spatial-frequency nature of ice water clouds, unique tomography algorithms were developed using filtered back-projection methods and direct inversion methods that use Gaussian basis functions. With the availability of a priori knowledge of the mean droplet size and the total water content at some point in the measurement plane, the tomography system can provide near real-time in-situ quantitative full-field total water content data at a measurement plane approximately 5 feet upstream of the engine inlet. Results from ice crystal clouds in the PSL are presented. In addition to the optical tomography technique, laser sheet imaging has also been applied in the PSL to provide planar ice cloud uniformity and relative water content data during facility calibration before the tomography system was available and also as validation data for the tomography system. A comparison between the laser sheet system and light extinction tomography resulting data are also presented. Very good agreement of imaged intensity and water content is demonstrated for both techniques. Also, comparative studies between the two techniques show excellent agreement in calculation of bulk total water content averaged over the center of the pipe.

Bencic, Timothy J.↗

NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Modal and nonmodal instability characteristics of cylindrically blunted flat plates with varying leading edge radii are described for Mach 4 and Mach 6 freestream conditions. The selection of leading edge radii and freestream parameters is informed by experimental conditions. The investigation of this 2D problem provides a slow entropy layer swallowing which allows for an isolated development of perturbations seeded upstream within different wall-normal regions of the flow. At both Mach numbers, a decrease in modal instability amplification was seen as the leading edge radius was increased. Nonmodal analysis reveals amplifying perturbations in the boundary layer as well as in the entropy layer. The medium bluntness regime exhibits the strongest amplification of nonmodal disturbances that is nonmonotonic in character. Small amplitude boundary forcing at the plate surface or volumetric forcing at various wall-normal heights was used to account for receptivity effects. While wall forcing effectively induced modal instabilities, only an actuation above the boundary layer captured disturbances that amplify within the entropy layer. The optimal nonmodal theory’s entropy-layer disturbance evolution exhibited outstanding agreement with controlled forcing, including receptivity effects. The evolution of entropy-layer disturbances from the optimal nonmodal theory showed excellent agreement with the results of receptivity to controlled forcing. Therefore, the nonmodal optimal growth analysis may provide a useful as well as efficient technique to identify the complete disturbance spectrum in blunt hypersonic configurations, where both modal and nonmodal disturbances can amplify in the boundary-layer and entropy-layer regions.

Boundary layer transition↗

NASA NTRS2022

Linear Disturbance Amplification Over Blunted Flat Plates in High-Speed Flows

Boundary layer transition↗

NASA NTRS1987

Guided-wave approaches to spectrally selective energy absorption

Results of experiments designed to demonstrate spectrally selective absorption in dielectric waveguides on semiconductor substrates are reported. These experiments were conducted with three waveguides formed by sputtering films of PSK2 glass onto silicon-oxide layers grown on silicon substrates. The three waveguide samples were studied at 633 and 532 nm. The samples differed only in the thickness of the silicon-oxide layer, specifically 256 nm, 506 nm, and 740 nm. Agreement between theoretical predictions and measurements of propagation constants (mode angles) of the six or seven modes supported by these samples was excellent. However, the loss measurements were inconclusive because of high scattering losses in the structures fabricated (in excess of 10 dB/cm). Theoretical calculations indicated that the power distribution among all the modes supported by these structures will reach its steady state value after a propagation length of only 1 mm. Accordingly, the measured loss rates were found to be almost independent of which mode was initially excited. The excellent agreement between theory and experiment leads to the conclusion that low loss waveguides confirm the predicted loss rates.

Stegeman, G. I.↗

NASA NTRS1983

Calculation of inviscid flow over shuttle-like vehicles at high angles of attack and comparisons with experimental data

A computer code HALIS, designed to compute the three dimensional flow about shuttle like configurations at angles of attack greater than 25 deg, is described. Results from HALIS are compared where possible with an existing flow field code; such comparisons show excellent agreement. Also, HALIS results are compared with experimental pressure distributions on shuttle models over a wide range of angle of attack. These comparisons are excellent. It is demonstrated that the HALIS code can incorporate equilibrium air chemistry in flow field computations.

Weilmuenster, K. J.↗

NASA NTRS1981

Statistical analysis of atmospheric turbulence about a simulated block building

An array of towers instrumented to measure the three components of wind speed was used to study atmospheric flow about a simulated block building. Two-point spacetime correlations of the longitudinal velocity component were computed along with two-point spatial correlations. These correlations are in good agreement with fundamental concepts of fluid mechanics. The two-point spatial correlations computed directly were compared with correlations predicted by Taylor's hypothesis and excellent agreement was obtained at the higher levels which were out of the building influence. The correlations fall off significantly in the building wake but recover beyond the wake to essentially the same values in the undisturbed, higher regions.

Steely, S. L., Jr.↗

NASA NTRS1961

Heat-Transfer Measurements on the Apexes of Two 60 deg Sweptback Delta Wings (Panel Semiapex Angle of 30 deg) Having 0 deg and 45 deg Dihedral at a Mach Number of 4.95

An experimental investigation was conducted to evaluate the heat-transfer rates at the apex of two 60 degree sweptback delta wings (panel semi-apex angle of 30 degrees) having cylindrical leading edges and 0 degrees and 45 degree positive dihedral. The models tested might correspond to the first several feet of a hypersonic reentry vehicle. The tests were conducted at a Mach number of 4.95 and a stagnation temperature of 400 F. nominal test-section unit Reynolds numbers varied from 2 x 10(exp 6) to 12 x 10(exp 6) per foot. The results of the investigation indicated that the laminar heat-transfer distributions (ratio of local to stagnation-line heating rate) about the models normal to the leading edges were in close agreement with two-dimensional blunt-body theory. The three-dimensional stagnation point heat-transfer rate on the 0 degree dihedral model was in excellent agreement with theory and the stagnation-line heat transfer on the straight portion of the leading edge of both models approached a constant level 12 percent above the theoretical stagnation-line level on an isolated swept infinite cylinder. When the heating rates on the 45 degree dihedral model (planform sweep of 69.3 degree) were compared with those on the 0 degree dihedral model (planform sweep of 60 degrees) at equal angles of attack and equal lifts greater than zero, the stagnation-line heating rates on the 45 degrees dihedral model were, in general, considerably lower as a result of the difference in effective sweeps of the leading edges. On the wing panels inboard from the stagnation lines, the differences in heating were very small. The stagnation-line heat-transfer variation with angle of attack, the shift in stagnation-line location, and the reduction in stagnation-line heat transfer resulting from the increase in effective sweep when positive dihedral is incorporated into a constant-panel 0 degree dihedral wing, all agreed with the results of a theoretical study made of highly swept delta wings with large positive dihedral.

Gunn, Charles R.↗

NASA NTRS2017

Fluid Transient Analysis during Priming of Evacuated Line

Water hammer analysis in pipe lines, in particularly during priming into evacuated lines is important for the design of spacecraft and other in-space application. In the current study, a finite volume network flow analysis code is used for modeling three different geometrical configurations: the first two being straight pipe, one with atmospheric air and other with evacuated line, and the third case is a representation of a complex flow network system. The numerical results show very good agreement qualitatively and quantitatively with measured data available in the literature. The peak pressure and impact time in case of straight pipe priming in evacuated line shows excellent agreement.

Bandyopadhyay, Alak↗

NASA NTRS2017

Status and Plans for Finalization of SRT's Contribution to AIRS Version-7 and Version-7 AO

Version-6.46 temperature profiles, water vapor profiles, and especially total O3, are very much compared to Version-6. With minor tweaking, Version-6.46 is a good candidate for use in Version-7. JPL Version-6.4.6 and Version-6.4.6 AO monthly mean products agree extremely well with each other. Version-6.4.6 AO is accurate enough that there is not necessarily a need to process both Version-7 and Version-7 AO data sets. Single day comparisons show Version-6.46 CrIS/ATMS and Version-6.46 AIRS/AMSU products agree extremely well with each other. We need to demonstrate agreement of Version-6.46 CrIS/ATMS and Version-6.46 AO products on a monthly mean basis for different months and years. CrIS/ATMS and AIRS/AMSU monthly mean comparisons showed excellent agreement using a previous version.

CrIS/ATMS↗

NASA NTRS1983

Field-incidence transmission of treated orthotropic and laminated composite panels

In an effort to improve understanding of the phenomenon of noise transmission through the sidewalls of an aircraft fuselage, an analytical model was developed for the field incidence transmission loss of an orthotropic or laminated composite infinite panel with layers of various noise insulation treatments. The model allows for four types of treatments, impervious limp septa, orthotropic trim panels, porous blankets, and air spaces, while it also takes into account the effects of forward speed. Agreement between the model and transmission loss data for treated panels is seen to be fairly good overall. In comparison with transmission loss data for untreated composite panels, excellent agreement occurred.

Koval, L. R.↗

NASA NTRS2016

The Low-Lying Electronic States of SiO

The singlet states of SiO that correlate with ground state atoms have been studied. The computed spectroscopic constants are in good agreement with experiment. The lifetime of the E state has been calculated to be 10.9 ns; this is larger than the results of previous computations and is in excellent agreement with the experimental value of 10.5 +/- 1.1 ns. The lifetime of the A state is about three times larger than found in experiment. We suggest that absorption from the X state to the (2)(exp 1) II state is responsible for the unidentified lines in the experiment of Hormes et al.

Charles W Bauschlicher↗

NASA NTRS2016

In Search of a Time Efficient Approach to Crack and Delamination Growth Predictions in Composites

Analysis benchmarking was used to assess the accuracy and time efficiency of algorithms suitable for automated delamination growth analysis. First, the Floating Node Method (FNM) was introduced and its combination with a simple exponential growth law (Paris Law) and Virtual Crack Closure technique (VCCT) was discussed. Implementation of the method into a user element (UEL) in Abaqus/Standard(Registered TradeMark) was also presented. For the assessment of growth prediction capabilities, an existing benchmark case based on the Double Cantilever Beam (DCB) specimen was briefly summarized. Additionally, the development of new benchmark cases based on the Mixed-Mode Bending (MMB) specimen to assess the growth prediction capabilities under mixed-mode I/II conditions was discussed in detail. A comparison was presented, in which the benchmark cases were used to assess the existing low-cycle fatigue analysis tool in Abaqus/Standard(Registered TradeMark) in comparison to the FNM-VCCT fatigue growth analysis implementation. The low-cycle fatigue analysis tool in Abaqus/Standard(Registered TradeMark) was able to yield results that were in good agreement with the DCB benchmark example. Results for the MMB benchmark cases, however, only captured the trend correctly. The user element (FNM-VCCT) always yielded results that were in excellent agreement with all benchmark cases, at a fraction of the analysis time. The ability to assess the implementation of two methods in one finite element code illustrated the value of establishing benchmark solutions.

Krueger, Ronald↗

NASA NTRS1977

Gravity model improvement using GEOS-3 (GEM 9 and 10)

The use of collocation permitted GEM 9 to be a larger field than previous derived satellite models, GEM 9 having harmonics complete to 20 x 20 with selected higher degree terms. The satellite data set has approximately 840,000 observations, of which 200,000 are laser ranges taken on 9 satellites equipped with retroreflectors. GEM 10 is complete to 22 x 22 with selected higher degree terms out to degree and order 30 amounting to a total of 592 coefficients. Comparisons with surface gravity and altimeter data indicate a substantial improvement in GEM 9 over previous satellite solutions; GEM 9 is in even closer agreement with surface data than the previously published GEM 6 solution which contained surface gravity. In particular the free air gravity anomalies calculated from GEM 9 and a surface gravity solution are in excellent agreement for the high degree terms.

Lerch, F. J.↗

NASA NTRS2016

Validation of High Speed Earth Atmospheric Entry Radiative Heating from 9.5 to 15.5 km/s

This paper presents an overview of the analysis and measurements of equilibrium radiation obtained in the NASA Ames Research Center's Electric Arc Shock Tube (EAST) facility as a part of recent testing aimed at reaching shock velocities up to 15.5 km/s. The goal of these experiments was to measure the level of radiation encountered during high speed Earth entry conditions, such as would be relevant for an asteroid, inter-planetary or lunar return mission. These experiments provide the first spectrally and spatially resolved data for high speed Earth entry and cover conditions ranging from 9.5 to 15.5 km/s at 13.3 and 26.6 Pa (0.1 and 0.2 Torr). The present analysis endeavors to provide a validation of shock tube radiation measurements and simulations at high speed conditions. A comprehensive comparison between the spectrally resolved absolute equilibrium radiance measured in EAST and the predictive tools, NEQAIR and HARA, is presented. In order to provide a more accurate representation of the agreement between the experimental and simulation results, the integrated value of radiance has been compared across four spectral regions (VUV, UV/Vis, Vis/NIR and IR) as a function of velocity. Results have generally shown excellent agreement between the two codes and EAST data for the Vis through IR spectral regions, however, discrepancies have been identified in the VUV and parts of the UV spectral regions. As a result of the analysis presented in this paper, an updated parametric uncertainty for high speed radiation in air has been evaluated to be [9.0%, -6.3%]. Furthermore, due to the nature of the radiating environment at these high shock speeds, initial calculations aimed at modeling phenomena that become more significant with increasing shock speed have been performed. These phenomena include analyzing the radiating species emitting ahead of the shock and the increased significance of radiative cooling mechanisms.

Equilibrium↗

NASA NTRS1978

Stratospheric NO and HNO3 observations in the Northern Hemisphere for three seasons

NO, HNO3, and O3 levels and air temperature were measured as a function of latitude in the 18 to 21 km region of the stratosphere, and the sum of odd nitrogen, equal to NO + NO2 + HNO3, was calculated and compared with model predictions. (NO2 values were inferred from photochemical equilibrium characteristics.) The data show that NO measurements generally exhibit good agreement with model predictions for low and midlatitudes but poor agreement at high latitudes. The experimental sum of odd nitrogen mixing ratios and model predictions agree within a factor of 2-1/2 or better at both 20 and 40 deg N, and show excellent agreement for latitudinal dependence.

Loewenstein, M.↗

NASA NTRS1977

Far-field multimodal acoustic radiation directivity

A comparison is made between approximate equations for far-field acoustic radiation patterns and exact equations for single and multimodal excitations in order to determine the validity range for the approximate approach. It is found that for single-mode cases: (1) the gross behavior of the primary lobes is adequately described by the approximate equations, (2) some error is found for lower and zero radial order modes, and (3) some agreement is yielded between exact and approximate sidelobes, although the approximate equation was not intended to simulate sidelobes. Multimodal approximate equations are compared to exact equations for various distributions of modal power; for all cases excellent agreement is found. For multimodal patterns it is noted that many modes influence the final level and shape of the directivity curve, although the major contributions are from the higher radial order modes.

Saule, A. V.↗