Search NASA⌕ Search

SEARCH · Search NASA

Results for “Extrusion Process”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

A novel freeform extrusion fabrication process for producing solid ceramic components with uniform layered radiation drying

An extrusion-based additive manufacturing process, called the Ceramic On-Demand Extrusion (CODE) process, for producing three-dimensional ceramic components with near theoretical density is introduced in this paper. Heere in this process, an aqueous paste of ceramic particles with a very low binder content (<1 vol%) is extruded through a moving nozzle at room temperature. After a layer is deposited, it is surrounded by oil (to a level just below the top surface of most recent layer) to preclude non-uniform evaporation from the sides. Infrared radiation is then used to partially, and uniformly, dry the just-deposited layer so that the yield stress of the paste increases and the part maintains its shape. The same procedure is repeated for every layer until part fabrication is completed. Several sample parts for various applications were produced using this process and their properties were obtained. The results indicate that the proposed method enables fabrication of large, dense ceramic parts with complex geometries.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Strength Variation in Processing Multiport Extrusion Tubes of A1100 and A3102 Alloys

The manufacturing process of multiport extrusion tubes generally includes homogenization, extrusion, roll leveling and heat treatment. In order to investigate the influence of the manufacturing procedures on strength variation of multiport extrusion tubes made of A1100 and A3102 alloys, the tube fabrication experiments and following materials characterization are carried out. The alloys’ stress–strain curves after every processing procedure are measured, and pressure-bearing capacity of the tubes is tested. The tubes’ strength and pressure-bearing capacity reach the peak values after straightening process and drop to the minimum after annealing. The contributions of solid solution hardening, grain boundary hardening and constituent particle strengthening to yield strength are evaluated. It is deduced that cluster hardening is the dominant strengthening mechanism for the as-homogenized and as-extruded samples; the contribution of clusters is second to work hardening after straightening process; slight cold work in conjunction with high-temperature annealing accelerates abnormal grain growth. The loss of strength increment from clusters can be interpreted by the remarkable reduction of high-angle grain boundaries after abnormal grain growth.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Techno-Economic Analysis for Shear Assisted Processing and Extrusion (ShAPE) of High Strength Aluminum Alloys

Aluminum alloy 7075 (AA7075) is a high strength aluminum alloy (HSAL), attractive for applications such as automotive, aviation, aerospace, defense, and marine applications. However, AA7075 has not yet been widely adopted due slow extrusion speed, high energy use, narrow process window, and sensitivity to incipient melting common in conventional extrusion methods. Alternative extrusion methods may overcome these limitations. New research funded by the U.S. Department of Energy (DOE) Advanced Manufacturing Office (AMO) is exploring the use of a new SPP approach called Shear Assisted Processing and Extrusion (ShAPE) for the manufacture of AA7075 extrusions. Pacific Northwest National Laboratory (PNNL) are leading the development, testing and characterization of ShAPE, which is showing that high speed ShAPE extrusions (e.g., above 12 meters/min) which is significantly faster than the 1-2 meters/min possible with conventional AA7075 extrusions. Initial findings from the economic and energy analysis indicate that AA7075 tubes created with ShAPE use less energy than tubes that are conventionally heated and extruded. The reduction in energy use is primarily a result of using direct chill cast (non-homogenized) billets, eliminating the pre-heating step, and faster extrusion speeds. The TEA model translates CAPEX and O&M costs to a manufacturing cost, and then a minimum sustainable price (MSP) per ton of extruded product for multiple facility capacities. A sample output figure of the TEA model is presented below. It presents results of the preliminary version of the TEA model.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2025

Assessment of Benefits of Solid-State Advanced Manufacturing Processes for Nuclear Energy Products

The Advanced Materials and Manufacturing Technology (AMMT) program develops cross cutting technologies in support of a broad range of nuclear reactor technologies and maintains U.S. leadership in materials and manufacturing technologies for nuclear energy applications. This overall project provides the U.S. Department of Energy a critical feasibility study comparison of three solid-state processes to other AM processes, thereby providing the feasibility of the solid-state processes examined to manufacture 316H SS and ODS steel components: • Fused-filament fabrication (FFF): This work provides an initial evaluation of the impact of powder morphology and sizes on the FFF process, and the feasibility and adaptability for different material systems, to use FFF for ODS steels and 316 SS. • Shear-assisted processing and extrusion (ShAPE): Specifically for this portion of the project on ShAPE tube forming, the objectives will be to determine the feasibility to direct tube forming of high tensile strength steel tubing, specifically for ODS steel to determine the effect of the patented extrusion process on the dispersoids of the ODS material. Additionally, as often ODS powders are mechanically alloyed and therefore more platelike or angular, this feasibility was to explore the impact on the optimization process and initial feasibility of direct tube forming. • Cold spray and friction stir additive manufacturing as a stretch goal: Bulk and near net shape manufacturing processes for high-temperature, high-strength alloys are needed. Additionally, cold spray techniques can be applied in-situ at the operational level for repair and can provide multiple benefits to the nuclear industry. These tasks aim to provide information to show benefits of cold spray during the full life cycle, namely research and development, product manufacturing, and repair to mention a few key points.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2013

Manufacture of gradient micro-structures of magnesium alloys using two stage extrusion dies

This paper aims to manufacture magnesium alloy metals with gradient micro-structures using hot extrusion process. The extrusion die was designed to have a straight channel part combined with a conical part. Materials pushed through this specially-designed die generate a non-uniform velocity distribution at cross sections inside the die and result in different strain and strain rate distributions. Accordingly, a gradient microstructure product can be obtained. Using the finite element analysis, the forming temperature, effective strain, and effective strain rate distributions at the die exit were firstly discussed for various inclination angles in the conical die. Then, hot extrusion experiments with a two stage die were conducted to obtain magnesium alloy products with gradient micro-structures. The effects of the inclination angle on the grain size distribution at cross sections of the products were also discussed. Using a die of an inclination angle of 15°, gradient micro-structures of the grain size decreasing gradually from 17 μm at the center to 4 μm at the edge of product were achieved.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear assisted processing and extrusion of enhanced strength aluminum alloy tubing

Hollow extrusions are used in many industries to make strong, lightweight, and affordable structures. Shear Assisted Processing and Extrusion (ShAPE) enables the extrusion of many alloys, often with noteworthy properties. In this investigation, ShAPE was used to extrude 1 and 2 mm wall tubes of aluminum alloy 6063 measuring 12 mm in diameter at extrusion speeds up to 3.8 m/min. This speed is 10 and 15 times faster than has been reported for any alloy using ShAPE and friction stir back extrusion, respectively. Increasing the extrusion speed from 0.7 to 3.8 m/s resulted in using 68% less process energy at steady state. Microstructural analysis and tensile testing were performed on as-extruded tubes and tubes with a direct T5 heat treatment. Grain refinement from 65 µm to below 20 µm was observed. Growth of macroscale Mg 2 Si strengthening precipitates was not observed. ShAPE processing resulted in recrystallization, and extrusion speed was shown to influence final extrudate texture. Here, transmission electron microscopy analysis revealed that the as-extruded microstructure was free of nanoscale ß" strengthening precipitates. Nanoscale ß" was prominent in direct-aged (T5) ShAPE tubes, similar to a slightly over-aged conventional T6 microstructure. As-extruded tubes had ultimate tensile strengths on par with conventional T5 extrusions and approximately double the total elongation. Tubes that underwent a T5 heat treatment had yield and ultimate strengths averaging 198 and 234 MPa, respectively, with an average total elongation of 11%. The tensile test results are comparable to a conventional T6 heat treatment, but without the solutionization heat treatment step. Mechanical properties either remained flat or improved with increased extrusion speed, which suggests that ShAPE can be scaled up to an industrial process to create energy- and economically efficient high-strength extrusions.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Fabrication of thin-walled tubes from alloy 602 CA using shear assisted processing and extrusion

Thin-walled tube is usually produced seamlessly via an expensive multi-step process or via welding of thin sheets but at reduced performance. To overcome the current process and performance inefficiencies, advanced manufacturing methods need to be investigated. In this investigation, shear assisted processing and extrusion (ShAPE) was used to fabricate thin-walled Inconel 602 tube in a single-step. Tubes measuring 0.83 m length with a 12 mm outer diameter and 1 mm wall thickness were fabricated with an average surface roughness, Ra of 1.6 µm and Rz of 15 µm. Tensile testing of tubes in the as-fabricated condition showed strength increases of 4-35% over current offerings while maintaining or improving elongation. Electron microscopy analysis revealed the recrystallized microstructure with refined inter- and intra-granular carbides. Preliminary results obtained in this investigation shows the feasibility of producing thin-wall high temperature tube in single-step via ShAPE. This achievement marks a significant step towards manufacturing larger diameter nickel alloy tubes for the U.S. Department of Energy’s Waste Treatment and Immobilization Plant.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Shear Assisted Processing and Extrusion of Magnesium Alloy Machining Chips

The Pacific Northwest National Laboratory (PNNL) utilized Shear Assisted Processing and Extrusion (ShAPE) to convert magnesium alloy machining chips directly into wrought material. PNNL fabricated 0.25” and 0.50” round rod from cold compacted briquettes pressed from dry-machined chips by Loukus Technologies. The alloy composition is proprietary and protected by a Materials Transfer Agreement (MTA) between PNNL and Loukus. Extrusions were fabricated using the ShAPE 2.0 machine, tooling, and process. PNNL is evaluating tensile properties per ASTM E8 and microstructure for grain size, texture, and porosity using Scanning Electron Microscopy (SEM) and Electron Backscatter Diffraction (EBSD). Tensile properties and microstructure results were not available at the time of writing this document. Extruded rods have also been sent to Loukus for evaluation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear Assisted Processing and Extrusion of Aluminum Alloy 7075 Tubing at High Speed

Conventional extrusion of aluminum alloy 7075 is limited to 1-2 meters per minute in order to avoid surface tearing and cracking. An emerging technique called Shear Assisted Processing and Extrusion (ShAPE) was used to extrude aluminum alloy 7075 tubing at a speed of 7.4 meters per minute without inducing surface defects. The faster extrusion speed is attributed to the unique flow characteristics inherent to the ShAPE process compared to conventional extrusion. Tubes with an inner diameter of 10 mm, outer diameter of 12 mm, and length of 2 meters were extruded at temperatures ranging from 340°C to 466°C. Tensile testing was performed per ASTM B557-15 with strain measured using digital image correlation. An ultimate tensile strength of 565 ± 4.6 MPa, yield strength of 496 ± 8.7 MPa, and elongation of 16.4 ± 1.0 % were measured for extrusion made at 362°C and heat treated to the T6 condition.

Shear Assisted Processing and Extrusion, Friction ↗
DOE OSTI2018

Effect of high content of manganese on microstructure, texture and mechanical properties of magnesium alloy

Highlights: • Extremely refined Mg-3.0Mn alloys are prepared by conventional extrusion process. • Mn addition can effectively weaken the basal texture of the alloys. • Strength, yield anisotropy and ductility have been obviously improved. - Abstract: In the present investigation, microstructure, texture and mechanical properties of Mg-3Mn alloys fabricated by hot extrusion process with the extrusion temperatures of 250 °C and 300 °C were investigated. The results revealed that the samples exhibited the refined microstructure and weakened basal texture. Refined microstructure of the samples was attributed to the dynamic precipitates suppressing the recrystallization grain growth during extrusion process. Weakened basal texture of the samples was explained as a result of particle stimulated nucleation (PSN) promoted by coarsened Mn precipitates altering the texture of extruded profiles during recrystallization by orienting the c-axis of grains at an angle that favors basal slip activity. As a result, the samples exhibited the high tensile elongation and good yield strength at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Study on Interfacial Phenomena in Aluminum–Aluminum Bimetal Fabricated by Extrusion at Different Temperatures

Aluminum–aluminum bimetal was prepared by spray-formed Al22Si alloy and ZL102 through extrusion process under solid–solid state, semisolid state and solid–liquid state. The microstructures and bonding strength of the bimetallic interface were studied, and the fracture behaviors of different bimetallic states were compared. The results showed that perfect metallic bond is produced through the semisolid extrusion process. The bimetal through solid–solid extrusion process is a large number of particles extruding through gaps among the cracked oxide layers, thus realized the metallurgical combination with the virgin metal. The process of semisolid extrusion is to break the oxide film under the temperature and pressure to achieve the bimetallic bonding. Besides, the hard particles wrapped by liquid metal can also enhance bonding strength. The tensile strength of bimetal fabricated by semisolid extrusion shows more promising results than that made by solid–solid combination and solid–liquid combination; the tensile strength improved from 83.3 to 120.5 MPa, an increase of about 45%. The process presented in this study provides a promising and effective approach for achieving Al22Si/Zl102 bimetal with high-quality metallurgical bonded interface.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Wrought Aluminum-Cerium Alloys by Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the very low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60% compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. These results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Metal Scrap Upcycling with Shear Assisted Processing and Extrusion (ShAPE)

The overarching objective of this project is to convert metal scraps, such as aluminum, titanium, and other alloys provided by the industry, into extruded tubing, wires, and rods. Upcycling of scrap will be accomplished using Shear Assisted Processing and Extrusion (ShAPE). This approach is a new solution for recycling. The specific aims of this project are as follows: 1. Receive metal scrap under a Material Transfer Agreement (MTA), in the form of billets, from select industry partners that meet the following requirements: outer diameter of 1.245 inches (+/-0.003 inches), inner diameter drilled with a 0.404-inch drill bit, and a length of 4.0 inches (+/-0.01 inches). The billet must be cast or compacted to greater than 98% density. If the industry partner does not have the capabilities to prepare the billets, PNNL can make introductions to third-party entities as needed. Industry partners will also provide a composition analysis as weight percent. 2. Extrude metal scrap via the ShAPE process at PNNL. 3. Evaluate and benchmark the extrudate material properties per the ASTM B557-15 – Testing Tubulars Standard or similar wire and rod standards. 4. Characterize the extrudate microstructure for any of the following: grain size, second phase composition, and texture. Additional testing may include corrosion per the ASTM B117 standard and electro-potential. 5. Deliver specimens to industry partners under an MTA for additional third-party evaluations. Industry partners will, in return, provide a non-proprietary report on any testing, including testing per the ASTM B557-15, ASTM B117, and other industry standards. 6. PNNL will develop data and insights to support intellectual property capture, a published non-proprietary technical report, research collaborations, and commercialization opportunities.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Microstructure stability of ultra-fine grained magnesium alloy AZ31 processed by extrusion and equal-channel angular pressing (EX–ECAP)

Thermal stability of the ultra-fine grained (UFG) microstructure of magnesium AZ31 alloy was investigated. UFG microstructure was achieved by a combined two-step severe plastic deformation process: the extrusion (EX) and subsequent equal-channel angular pressing (ECAP). This combined process leads to refined microstructure and enhanced microhardness. Specimens with UFG microstructure were annealed isochronally at temperatures 150–500 °C for 1 h. The evolution of microstructure, mechanical properties and dislocation density was studied by electron backscatter diffraction (EBSD), microhardness measurements and positron annihilation spectroscopy (PAS). The coarsening of the fine-grained structure at higher temperatures was accompanied by a gradual decrease of the microhardness and decrease of dislocation density. Mechanism of grain growth was studied by general equation for grain growth and Arrhenius equation. Activation energies for grain growth were calculated to be 115, 33 and 164 kJ/mol in temperature ranges of 170–210 °C, 210–400 °C and 400–500 °C (443–483 K, 483–673 K and 673–773 K), respectively. - Highlights: • Microhardness of UFG AZ31 alloy decreases with increasing annealing temperature. • This fact has two reasons: dislocation annihilations and/or grain growth. • The activation energies for grain growth were calculated for all temperature ranges.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural refinement of an Al-Ce-Mg alloy via Shear Assisted Processing and Extrusion

Al-Ce alloys have attracted recent interest because of their high thermal stability due to the low solubility of Ce in the Al matrix. The Al 11 Ce 3 eutectic phase gives excellent strain hardening behavior and moderate high-temperature strength in the as-cast state. However, its strengthening effect is limited by its coarse as-cast structure. Therefore, alternative manufacturing methods such as additive manufacturing or equal channel angular pressing have been applied to refine the Al 11 Ce 3 phase to good effect. However, these techniques are both expensive and time-consuming. Therefore, this study aims to use Shear Assisted Processing and Extrusion (ShAPE), an emerging solid phase processing technique that is more easily scalable than the previously mentioned methods. ShAPE can produce useful cross-sections of an Al-8Ce-4Mg alloy while refining the Al 11 Ce 3 phase to produce a higher strength material. It was found that a low temperature ShAPE process can improve the room temperature yield strength by ~60 % compared to a binary Al-4Mg alloy. Additionally, the high-temperature yield strength of the Al-Ce alloys increased by 20%, with a simultaneous 15% improvement in ductility compared to the binary Al-Mg alloy. Finally, these results highlight the potential for ShAPE as a processing technique for Al-Ce alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Conversion of real-world aluminum scrap streams into high-performance Al–Mg–Si–Cu automotive alloys using shear assisted processing and extrusion

The conversion of post-consumer aluminum (Al) scrap into usable Al alloys without adding primary Al is challenging because of excess impurities. In this work, >99% post-consumer Twitch, used beverage cans (UBCs), and remelt scrap ingots (RSIs) were used as feedstock materials. As-cast and solution heat-treated feedstock billets were extruded using Shear Assisted Processing and Extrusion (ShAPE) at ~510°C, followed by press quenching. To explore the development of the microstructure, texture, and underlying mechanisms and how they contribute to the overall strengthening in as-extruded and artificially aged samples, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) were used to collect microstructure and texture data. The enhanced strength and ductility were corroborated with the microstructural features and crystallographic texture. Simple shear $\textrm{A}/\bar{\textrm{A}}$, $\textrm{A}_1^*/\textrm{A} _2^*$ texture components along with weak $\textrm{C}$ and $\textrm{B}/\bar{\textrm{B}}$ texture components were formed during extrusion; the texture was strengthened after heat treatment. The refined second-phase particles helped to retain the deformed microstructure and texture. The contributions of dislocation and precipitate strengthening were maximized when billets were solution-heat-treated prior to extrusion. This is attributed to the formation of effective supersaturated solid solutions during the ShAPE process, which precipitate out during the peak age treatment. Overall, the highest yield strength of 305 MPa, ultimate tensile strength of 350 MPa, and elongation of 12% were achieved in artificially aged samples, which are comparable to those of Al 6082-T6.

Al alloy↗
DOE OSTI2025

Upcycling of aluminum Twitch scrap via Shear Assisted Processing and Extrusion (ShAPE)

Aluminum is publicly perceived as recyclable, but mixed alloys and impurities in aluminum scrap require dilution via energy-intensive primary aluminum or downcycling to low-quality castings. In this study, cast billets of shredded aluminum scrap (Twitch) were blended with pre-consumer AA 6061, extruded into tubes via Shear Assisted Processing and Extrusion (ShAPE), and aged to T1 and T6 tempers. Microscopy reveals that ShAPE refined and distributed the deleterious AlFeSi phases. Furthermore, the Twitch extrusions had tensile properties comparable to AA 6061 yet without homogenizing or adding primary aluminum. Energy savings were 85% compared to conventional extrusion of primary aluminum alloys.

ShAPE↗
DOE OSTI2019

Elucidating the Effect of TiB{sub 2} Volume Percentage on the Mechanical Properties and Corrosion Behavior of Al5083-TiB{sub 2} Composites

Al5083-TiB{sub 2} in situ composites with 1, 3, and 5 volume percentages of TiB{sub 2} were fabricated. The effect of different volume percentages of TiB{sub 2} reinforcement particles on the mechanical properties and corrosion resistance of these composites was investigated. The hot extrusion process resulted in fragmentation and more homogeneous distribution of TiB{sub 2} particles throughout the Al5083 matrix. Also, the grain size reduced as the amount of TiB{sub 2} reinforcement particles increased which caused the improvement of both the strength and ductility of the material. It was shown that the hardness, the ultimate tensile strength (UTS), and the yield strength (YS) of both the as-cast and extruded materials increased with increasing TiB{sub 2} content. Also, TiB{sub 2} addition combined with the extrusion process improved both UTS and elongation (El.%) of the extruded structures which can be attributed to the presence of TiB{sub 2} particles and obtained microstructural refinement by hot extrusion process. However, the extruded Al5083-5 vol.% TiB{sub 2} composite showed lower ductility in comparison with the extruded Al5083-1 vol.% TiB{sub 2} and Al5083-3 vol.% TiB{sub 2} composites. Moreover, it could be concluded that the corrosion resistance and also the pitting corrosion behavior of the Al5083 alloy do not significantly change in the presence of TiB{sub 2} reinforcement particles.

36 MATERIALS SCIENCE↗