Search NASA⌕ Search

SEARCH · Search NASA

Results for “FINS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Field intercomparison of ice nucleation measurements: the Fifth International Workshop on Ice Nucleation Phase 3 (FIN-03)

Abstract. The third phase of the Fifth International Ice Nucleation Workshop (FIN-03) was conducted at the Storm Peak Laboratory in Steamboat Springs, Colorado, in September 2015 to facilitate the intercomparison of instruments measuring ice-nucleating particles (INPs) in the field. Instruments included two online and four offline measurement systems for INPs, which are a subset of those utilized in the laboratory study that comprised the second phase of FIN (FIN-02). The composition of the total aerosols was characterized using the Particle Analysis by Laser Mass Spectrometry (PALMS) and Wideband Integrated Bioaerosol Sensor (WIBS) instruments, and aerosol size distributions were measured by a laser aerosol spectrometer (LAS). The dominant total particle compositions present during FIN-03 were composed of sulfates, organic compounds, and nitrates, as well as particles derived from biomass burning. Mineral-dust-containing particles were ubiquitous throughout and represented 67 % of supermicron particles. Total WIBS fluorescing particle concentrations for particles with diameters of > 0.5 µm were 0.04 ± 0.02 cm−3 (0.1 cm−3 highest; 0.02 cm−3 lowest), typical of the warm season in this region and representing ≈ 9 % of all particles in this size range as a campaign average. The primary focus of FIN-03 was the measurement of INP concentrations via immersion freezing at temperatures > −33 °C. Additionally, some measurements were made in the deposition nucleation regime at these same temperatures, representing one of the first efforts to include both mechanisms within a field campaign. INP concentrations via immersion freezing agreed within factors ranging from nearly 1 to 5 times on average between matched (time and temperature) measurements, and disagreements only rarely exceeded 1 order of magnitude for sampling times coordinated to within 3 h. Comparisons were restricted to temperatures lower than −15 °C due to the limits of detection related to sample volumes and very low INP concentrations. Outliers of up to 2 orders of magnitude occurred between −25 and −18 °C; a better agreement was seen at higher and lower temperatures. Although the 5–10 factor agreement of INP measurements found in FIN-03 aligned with the results of the FIN-02 laboratory comparison phase, giving confidence in progress of this measurement field, this level of agreement still equates to temperature uncertainties of 3.5 to 5 °C that may not be sufficient for numerical cloud modeling applications that utilize INP information. INP activity in the immersion-freezing mode was generally found to be an order of magnitude or more, making it more efficient than in the deposition regime at 95 %–99 % water relative humidity, although this limited data set should be augmented in future efforts. To contextualize the study results, an assessment was made of the composition of INPs during the late-summer to early-fall period of this study inferred through comparison to existing ice nucleation parameterizations and through measurement of the influence of thermal and organic carbon digestion treatments on immersion-freezing ice nucleation activity. Consistent with other studies in continental regions, biological INPs dominated at temperatures of > −20 °C and sometimes colder, while arable dust-like or other organic-influenced INPs were inferred to dominate below −20 °C.

54 ENVIRONMENTAL SCIENCES↗

Radiation from an array of gray circular fins of trapezoidal profile

A numerical method is developed to calculate the temperature distribution and radiation heat transfer for an annular fin and tube radiator, with fins having trapezoidal profiles. All surfaces are assumed gray and to emit and reflect diffusely. Radiative interactions between adjacent fins and between the fins and tube are included. The thermal conductivity of the fin material may vary linearly with temperature. Results of a parametric study of the special case of circular fins of triangular profile having constant thermal conductivity are presented and used to optimize a fin array with respect to minimum weight.

Schnurr, N. M.↗

Radiation from an array of longitudinal fins of triangular profile

Radiation from an array of longitudinal fins of triangular profile is analyzed, including fin-to-fin and fin-to-base interactions. The effect of base cylinder radiation and the fin-base radiative interaction is found to be significant for fin width/tube radius ratios less than 8. Results presented may be used to optimize the design of a fin array with respect to weight.

Schnurr, N. M.↗

Experimental investigation of vortices shed by various wing fin configurations

Forty-six different fins, which were members of twelve plan-form families, were tested. A two dimensional Boeing single element airfoil at an angle of attack of eight degrees and a sweepback angle of thirty-two was used to simulate a portion of the wing of a generator aircraft. Various free stream velocities were used to test any individual fin at its particular angle of attack. While the fin itself was mounted on the upper surface of the generator model, the angle of attack of each fin was varied until stall was reached and/or passed. The relative fin vortex strengths were measured in two ways. First, the maximum angular velocity of a four blade rotor placed in the fin vortex center was measured with the use of a stroboscope. Second, the maximum rolling moment on a following wing model placed in the fin vortex center was measured by a force balance.

Iversen, J.↗

PNS predictions for supersonic/hypersonic flows over finned missile configurations

Finned missile design entails accurate and computationally fast numerical techniques for predicting viscous flows over complex lifting configurations at small to moderate angles of attack and over Mach 3 to 15; these flows are often characterized by strong embedded shocks, so that numerical algorithms are also required to capture embedded shocks. The recent real-gas Flux Vector Splitting technique is here extended to investigate the Mach 3 flow over a typical finned missile configuration with/without side fin deflections. Elliptic grid-generation techniques for Mach 15 flows are shown to be inadequate for Mach 3 flows over finned configurations and need to be modified. Fin-deflection studies indicate that even small amounts of missile fin deflection can substantially modify vehicle aerodynamics. This 3D parabolized Navier-Stokes scheme is also extended into an efficient embedded algorithm for studying small axially separated flow regions due to strong fin and control surface deflections.

Bhutta, Bilal A.↗

Heat-transfer coefficients for air flowing in round tubes, in rectangular ducts, and around finned cylinders

Report reviews published data and presents some new data on heat transfer to air flowing in round tubes, in rectangular ducts, and around finned cylinders. The available data for heat transfer to air in straight ducts of rectangular and circular cross section have been correlated in plots of Stanton number versus Reynolds number to provide a background for the study of the data for finned cylinders. Equations are recommended for both the streamlined and turbulent regions, and data are presented for the transition region between turbulent and laminar flow. Use of hexagonal ends on round tubes causes the characteristics of laminar flow to extend to high Reynolds numbers. Average coefficients for the entire finned cylinder have been calculated from the average temperature at the base of the fins and an equation which was derived to allow for the effectiveness of the fins. The available results for each finned cylinder are correlated herein in terms of graphs of Stanton number versus Reynolds number. In general, for a given Reynolds number, the Stanton number increases with increases in both spacing and width of the fins, and is apparently independent of cylinder diameter and temperature difference. For a given coefficient of heat transfer improved baffles and rough or wavy surfaces give a substantial reduction in pumping power per unit of heat transfer surface and a somewhat smaller decrease in pressure drop. (author)

Drexel, Rober E↗

Wind-tunnel Tests of a Model of a Wingless Fin-controlled Missile to Obtain Static Stability and Control Characteristics Through a Range of Mach Numbers from 0.5 to 0.88

An investigation at medium to high subsonic speeds has been conducted in the Langley low-turbulence pressure tunnel to determine the static stability and control characteristics and to measure the fin normal forces and moments for a model of a wingless fin-controlled missile. The data were obtained at Reynolds number of 2.1 x 10(6) based on the missile maximum diameter or 17.7 x 10(6) based on missile length; this Reynolds number was found to be large enough to avoid any large scale effects between the test and the expected flight Reynolds number. With the horizontal-fin deflection limited to a maximum of 6 degrees, longitudinally stable and trimmed flight could not be maintained beyond an angle of attack of 17 degrees for a Mach number of 0.88 and beyond 20 degrees for a Mach number of 0.50 for any center-of-gravity location without the use of some auxiliary stability or control device such as jet vanes. Mach number had no appreciable effect on the center-of-pressure positions and only a slight effect on neutral-point position. There was a shift in neutral-point position of about 1 caliber as the angle of attack was varied through the range for which the neutral point could be determined. Yawing the model to angles of sideslip up to 7 degrees had little effect on the longitudinal stability at angles of attack up to 15 degrees; however, above 15 degrees, the effect of sideslip was destabilizing. With the vertical fins at a plus-or-minus 6 degree roll deflection, the rolling moment caused by yawing the model at high angles of attack could be trimmed out up to angles of sideslip of 6.5 degrees and an angle of attack of 26 degrees for a Mach number of 0.50; this range of sideslip angles was reduced to 3 degrees at a Mach number of 0.88. The data indicated that, at lower angles of attack, the trim range extended to higher angles of sideslip. The total normal-force and hinge-moment coefficients for both horizontal fins were slightly nonlinear with both angle-of-attack and fin deflection. The effect of Mach number was to reduce the slopes of the hinge-moment coefficient with angle of attack and deflection angle. In general, the effort of increasing the sideslip angle was to reduce the values of the fin normal-force and hinge-moment coefficients.

Burrows, Dale L↗

Static Longitudinal Stability of a Rocket Vehicle Having a Rear-Facing Step Ahead of the Stabilizing Fins

Tests were conducted at Mach numbers of 3.96 and 4.65 in the Langley Unitary Plan wind tunnel to determine the static longitudinal stability characteristics of a fin-stabilized rocket-vehicle configuration which had a rearward facing step located upstream of the fins. Two fin sizes and planforms, a delta and a clipped delta, were tested. The angle of attack was varied from 6 deg to -6 deg and the Reynolds number based on model 6 length was about 10 x 10. The configuration with the larger fins (clipped delta) had a center of pressure slightly rearward of and an initial normal-force-curve slope slightly higher than that of the configuration with the smaller fins (delta) as would be expected. Calculations of the stability parameters gave a slightly lower initial slope of the normal-force curve than measured data, probably because of boundary-layer separation ahead of the step. The calculated center of pressure agreed well with the measured data. Measured and calculated increments in the initial slope of the normal-force curve and in the center of pressure, due to changing fins, were in excellent agreement indicating that separated flow downstream of the step did not influence flow over the fins. This result was consistent with data from schlieren photographs.

Keynton, Robert J.↗

Aerothermoelastic Analysis of a NASP-Like Vertical Fin

Several aeroelastic stability analyses for a vertical fin similar to that of the National Aero-Space Plane are described. The objectives of the study were to design and obtain an experimental data base for a supersonic wind-tunnel model of the fin in order to examine the effects of thermal loading on the flutter characteristics. This paper describes the preliminary efforts to design the wind-tunnel model, including several of the geometric parameter variations that were analyzed. The dominant flutter mechanism involved a flap vibration mode and a fin bending mode. Variation of the thicknesses of flap and root flexures, used to attach the flap to the fin, and the fin to a support, significantly affected the flutter boundary. Uniform thermal loads, affecting only material properties, had little effect, as did the application of different uniform temperatures to each side of the fin. In contrast, the application of significant chord-wise thermal gradients induced stresses which reduced the flutter dynamic pressure by as much as 37 percent. For less extreme distributed loading, the low-aspect ratio fin was relatively unaffected.

Rodgers, John P.↗

Pattern bonded finned cold plate

An apparatus includes a fin pack of parallel plates that protrude from a base, a lid attachable to the fin pack opposite the base, and a brazing material painted onto the lid only in a plurality of wettable regions. The lid is positioned against the fin pack, opposite the base, with portions of the plurality of regions contacting edges of the parallel plates. The lid is brazed to the fin pack without intrusion of the brazing material between the parallel plates. This is accomplished by obtaining a lid to be attached to a fin pack of parallel plates that protrude from a base, painting the lid with the brazing material only in a plurality of wettable regions, positioning the lid against the fin pack, opposite the base, with portions of the plurality of regions contacting edges of the parallel plates, and brazing the lid to the fin pack.

Schultz, Mark D.↗

A new flow pattern map for flow boiling of R410A in horizontal micro-fin tubes considering the effect of the helix angle

This paper presents an improved flow pattern map for flow boiling in horizontal micro-fin tubes considering the effect of helix angle. The proposed map is modified from the one developed for horizontal smooth tubes by Wojtan et al. (2005) and takes the early transition to annular flow due to micro-fin geometry into account. Visualization of R410A flow boiling is carried out through the transparent smooth and micro-fin tubes with 0°, 10° and 18° helix angle and plotted on the proposed map for comparison. The result shows that the flow pattern map for micro-fin tube with 0° helix angle is generally similar to that for the smooth tube. For the tube with 10° and 18° helix angle, the annular flow occurs at lower vapor quality and lower mass flux. The proposed map shows good agreements when compared with the visualization and reflects the downward shift (to lower mass flux and vapor quality conditions) of the SW-WA transition with the increase of the helix angle. In order to further validate the proposed model, the flow pattern transitions calculated from the equations are also compared with the experimental data of the micro-fin tube in literature. The results show that the modified map increase the prediction accuracy of the flow patterns in the micro-fin tube.

42 ENGINEERING↗

POPs in free-ranging pilot whales, sperm whales and fin whales from the Mediterranean Sea: Influence of biological and ecological factors

The pilot whale Globicephala melas, the sperm whale Physeter macrocephalus, and the fin whale Balaenoptera physalus are large cetaceans permanently inhabiting the Mediterranean Sea. These species are subjected to numerous anthropogenic threats such as exposure to high levels of contaminants. Therefore, selected persistent organic pollutants POPs (29 PCBs, 15 organochlorine compounds, 9 PBDEs and 17 PCDD/Fs) were analysed in blubber biopsies of 49 long-finned pilot whales, 61 sperm whales and 70 fin whales sampled in the North Western Mediterranean Sea (NWMS) from 2006 to 2013. Contamination profile and species feeding ecology were then combined through the use of stable isotopes. δ{sup 13}C, δ{sup 15}N values and POPs levels were assessed through IR-MS and GC–MS respectively. To assess the toxic potency of the dioxin-like compounds, the TEQ approach was applied. δ{sup 15}N values were 12.2±1.3‰ for sperm whales, 10.5±0.7‰ for pilot whales and 7.7±0.8‰ in fin whales, positioning sperm whales at higher trophic levels. δ{sup 13}C of the two odontocetes was similar and amounted to −17.3±0.4‰ for sperm whales and −17.8±0.3‰ for pilot whales; whilst fin whales were more depleted (−18.7±0.4‰). This indicates a partial overlap in toothed-whales feeding habitats, while confirms the differences in feeding behaviour of the mysticete. Pilot whales presented higher concentrations than sperm whales for ΣPCBs (38,666±25,731 ng g{sup −1} lw and 22,849±15,566 ng g{sup −1} lw respectively), ΣPBDEs (712±412 ng g{sup −1} lw and 347±173 ng g{sup −1} lw respectively) and ΣDDTs (46,081±37,506 ng g{sup −1} lw and 37,647±38,518 ng g{sup −1} lw respectively). Fin whales presented the lowest values, in accordance with its trophic position (ΣPCBs: 5721±5180 ng g{sup −1} lw, ΣPBDEs: 177±208 ng g{sup −1} lw and ΣDDTs: 6643±5549 ng g{sup −1} lw). Each species was characterized by large inter-individual variations that are more related to sex than trophic level, with males presenting higher contaminant burden than females. The discriminant analysis (DA) confirmed how DDTs and highly chlorinated PCBs were influential in differentiating the three species. Pollutant concentrations of our species were significantly higher than both their Southern Hemisphere and North Atlantic counterparts, possibly due to the particular Mediterranean geomorphology, which influences pollutants distribution and recycle. Dioxin-like PCBs accounted for over 80% of the total TEQ. This study demonstrated (1) an important exposure to pollutants of Mediterranean cetaceans, often surpassing the estimated threshold toxicity value of 17,000 ng g{sup −1} lw for blubber in marine mammals; and (2) how the final pollutant burden in these animals is strongly influenced not only by the trophic position but also by numerous other factors such as sex, age, body size and geographical distribution. - Highlights: • We analysed POPs concentrations in cetaceans from North-western Mediterranean Sea. • We integrated δ{sup 13}C and δ{sup 15}N values to combine trophic position and contamination. • Odontocetes show PCBs level higher than the toxicity threshold of 17 μg g{sup −1} lw. • Trophic position, sex, body size and distribution affect interspecies diversity.

54 ENVIRONMENTAL SCIENCES↗

Characterization and Scaling of Forced Convective Swirl in Sinusoidal Wavy-Plate-Fin Cores of Compact Heat Exchangers

The characterization and scaling of the thermal-hydraulic performance in wavy plate-fin compact heat exchanger cores, based on the understanding of the physical phenomena and heat transfer enhancement mechanism is delineated. Experimental data are presented for forced convection in air (Pr = 0.71) with flow rates in the range 50 ≤ Re ≤ 4000. A variety of wavy-fin cores that span viable applications, with geometrical attributes described by the cross section aspect ratio α (ratio of fin spacing to height), fin corrugation aspect ratio γ (ratio of 2× corrugation amplitude to wave pitch), and fin spacing ratio ζ (ratio of fin spacing to wave pitch), are considered. To characterize and correlate the vortex-flow mixing in interfin spaces, a Swirl number Sw is introduced from the balance of viscous, inertial and centrifugal forces. It is shown that the laminar, transitional and turbulent flow regimes can be explicitly identified by this Swirl number. Based on the experimental results and extended analysis, new correlations for Fanning friction factor f and Colburn factor j are developed with Sw, α, γ, and ζ as scaling parameters. Requisite expressions are devised by a superposition of both enhancement components due to the corrugated surface area enlargement and induced swirl flow field, and they are combined to cover the laminar, transitional and turbulent regimes by the method of asymptotic matching. The resulting generalized correlations are further shown to predict all available experimental data for f and j factors to within ±20% and ±15%, respectively.

42 ENGINEERING↗

Some effects of tip fins on wing flutter characteristics

A wind tunnel investigation has been conducted over the Mach number range from about 0.6 to 1.2 to determine the effects of large tip fins on the flutter characteristics of a swept wing. The basic wing configuration had an aspect ratio of 0.95, leading-edge sweep of 40 deg 0, and trailing-edge sweep of 21 deg. Two of these configurations were modified with tip fins of 60 deg dihedral and had effective aspect ratios of 1.5 and 2.2. In general, the results indicate that the addition of tip fins reduces the flutter speed, with the larger fin having the greater effect. Comparison of the experimental flutter speeds at Mach numbers between 0.60 and 0.90 with calculated values obtained by using doublet-lattice unsteady aerodynamic theory was good. Analytical results where structural and aerodynamic effects of the tip fins were isolated indicated that the reduction in flutter speed produced by the addition of the fins was caused by both effects, with the structural effect being the more pronounced.

Goetz, R. C.↗

Effect of wing fins on lift-generated wakes

A theoretical and experimental study has been made of the effect of wing-mounted fins on the vortex wakes of subsonic aircraft. The theory is used (a) to gain an understanding of wake alleviation by vortex injection and (b) to guide the experimental investigation. Wind-tunnel tests were used to evaluate the alleviation achievable and to find the optimum values for the various fin parameters. It was found that vertical fins mounted on the upper surface of a wing could lower the wake-induced rolling moments on an encountering wing by a factor of 3 or more. The most promising fin configuration found for the Boeing 747 model is a fin positioned 48% outboard from the centerline to the wingtip with a height of 0.014 span, a chord of 0.085 span, and an 18 deg angle of attack. This fin configuration caused a 10% increase in drag but no lift penalty.

Rossow, V. J.↗

Transonic static and dynamic stability characteristics of a finned projectile configuration

Static and dynamic stability tests were made of a finned projectile configuration with the aft-mounted fins arranged in a cruciform pattern. The tests were made at free stream Mach numbers of 0.7, 0.9, 1.1, and 1.2 in the Langley 8-foot transonic pressure tunnel. Some of the parameters measured during the tests were lift, drag, pitching moment, pitch damping, and roll damping. Configurations tested included the body with undeflected fins, the body with various fin deflections for control, and the body with fins removed. Theoretical estimates of the stability derivatives were made for the fins on configuration.

Boyden, R. P.↗

Low-speed wind-tunnel investigation of wing fins as trailing-vortex-alleviation devices on a transport airplane model

The trailing-vortex-alleviation effectiveness of both a one- and a two-fin configuration (semicircular with a radius of 0.043 semispan) on a jumbo-jet transport airplane model in its landing configuration was investigated in the Langley V/STOL tunnel, by the trailing-wing sensor technique. The fins were located on the upper surface of the transport model wing along the 30-percent-chord line. The fin configurations were effective in reducing the vortex-induced rolling moment, by amounts varying from 28 to 60 percent, on the trailing wing model located at a distance of 7.8 transport model wing spans downstream of the transport model. The flow over the fins and over the transport airplane model wing downstream of the fins was observed to be separated and turbulent. All fin configurations caused a reduction in maximum lift coefficient, a positive increment in drag coefficient, and an increment in nose-up pitching-moment coefficient on the transport airplane model.

Croom, D. R.↗

Overall contact conductance of a prototype Parallel Fin Thermal Interface

The Parallel Fin Thermal Interface has been developed and tested as an orbital replaceable interface. The interface consists of two identical plates with pairs of opposing parallel straight fins. Each pair of fins is sandwiched between two insert plates pressed against the fins with enough force for good heat transfer through the interface. Two prototype parallel fin interfaces were built (Model 140 and 380) with different fin and insert plate dimensions. Samples of the interfacing surfaces were found to have roughness values ranging from 22 to 35 microinches. Overall interface conductance (Hc) values of 46.7 to 74.2 Btu/hr sq ft-F were obtained for the 140 model in vacuum with an interface pressure from 18.8 to 37.5 psi, respectively. The Model 380 exhibited Hc values from 31.2 to 46.8 Btu/hr sq ft-F in vacuum, with respective interface pressures of 14.2 and 22.0 psi. Several correlations were found to agree with test data to within 20 percent.

Stobb, C. A.↗